High and selective CO2 capture by two mesoporous acylamide-functionalized rht-type metal-organic frameworks

Two mesoporous and flexible acylamide-functionalized rht-type MOFs exhibit not only high excess unsaturation CO(2) uptake (157 wt%) at 20 bar and 273 K, but also good selectivity of CO(2)/CH(4) (8.6) and CO(2)/N(2) (34.3). The advantages of acylamide groups for CO(2) capture have been further confirmed by GCMC and first-principles calculations.     

High CO2 uptake and selectivity by triptycene-derived benzimidazole-linked polymers

Successful incorporation of triptycene into benzimidazole-linked polymers leads to the highest CO(2) uptake (5.12 mmol g(-1), 273 K and 1 bar) by porous organic polymers and results in high CO(2)/N(2) (63) and CO(2)/CH(4) (8.4) selectivities.     

Design of covalent organic frameworks for methane storage

We designed 14 new covalent organic frameworks (COFs), which are expected to adsorb large amounts of methane (CH(4)) at 298 K and up to 300 bar. We have calculated their delivery uptake using grand canonical Monte Carlo (GCMC) simulations. We also report their thermodynamic stability based on 7.5 ns molecular dynamics simulations. Two new frameworks, COF-103-Eth-trans and COF-102-Ant, are found to exceed the DOE target of 180 v(STP)/v at 35 bar for methane storage. Their performance is comparable to the best previously reported materials: PCN-14 and Ni-MOF-74. Our results indicate that using thin vinyl bridging groups aid performance by minimizing the interaction methane-COF at low pressure. This is a new feature that can be used to enhance loading in addition to the common practice of adding extra fused benzene rings. Most importantly, this report shows that pure nonbonding interactions, van der Waals (vdW) and electrostatic forces in light elements (C, O, B, H, and Si), can rival the enhancement in uptake obtained for microporous materials derived from early transition metals.     

A mesoporous metal-organic framework constructed from a nanosized C3-symmetric linker and [Cu24(isophthalate)24] cuboctahedra

The mesoporous framework [Cu(3)(L)(H(2)O)(3)]·(DMF)(35)·(H(2)O)(35) (NOTT-119) shows on desolvation a BET surface area of 4118(200) m(2) g(-1), a pore volume of 2.35 cm(3) g(-1), a total H(2) uptake of 101 mg g(-1) at 60 bar, 77 K and a total CH(4) uptake of 327 mg g(-1) at 80 bar, 298 K.     

Microporous polycarbazole with high specific surface area for gas storage and separation

Microporous polycarbazole via straightforward carbazole-based oxidative coupling polymerization is reported. The synthesis route exhibits cost-effective advantages, which are essential for scale-up preparation. The Brunauer-Emmett-Teller specific surface area for obtained polymer is up to 2220 m(2) g(-1). Gas (H(2) and CO(2)) adsorption isotherms show that its hydrogen storage can reach to 2.80 wt % (1.0 bar and 77 K) and the uptake capacity for carbon dioxide is up to 21.2 wt % (1.0 bar and 273 K), which show a promising potential for clean energy application and environmental field. Furthermore, the high selectivity toward CO(2) over N(2) and CH(4) makes the obtained polymer possess potential application in gas separation.     

MIL-96, a porous aluminum trimesate 3D structure constructed from a hexagonal network of 18-membered rings and mu3-oxo-centered trinuclear units

A new aluminum trimesate Al12O(OH)18(H2O)3(Al2(OH)4)[btc]6.24H2O, denominated MIL-96, was synthesized under mild hydrothermal conditions (210 degrees C, 24 h) in the presence of 1,3,5-benzenetricarboxylic acid (trimesic acid or H3btc) in water. Hexagonal crystals, allowing a single-crystal XRD analysis, are grown from a mixture of trimethyl 1,3,5-benzenetricarboxylate (Me3btc), HF, and TEOS. The MIL-96 structure exhibits a three-dimensional (3D) framework containing isolated trinuclear mu3-oxo-bridged aluminum clusters and infinite chains of AlO4(OH)2 and AlO2(OH)4 octahedra forming a honeycomb lattice based on 18-membered rings. The two types of aluminum groups are connected to each other through the trimesate species, which induce corrugated chains of aluminum octahedra, linked via mu2-hydroxo bonds with the specific -cis-cis-trans- sequence. The 3D framework of MIL-96 reveals three types of cages. Two of them, centered at the special positions 0 0 0 and 2/3 1/3 1/4, have estimated pore volumes of 417 and 635 A3, respectively, and encapsulate free water molecules. The third one has a smaller pore volume and contains disordered aluminum octahedral species (Al(OH)6). The solid-state NMR characterization is consistent with crystal structure and elemental and thermal analyses. The four aluminum crystallographic sites are resolved by means of 27Al 3QMAS technique. This product is able to sorb both carbon dioxide and methane at room temperature (4.4 mmol.g(-1) for CO2 and 1.95 mmol.g(-1) for CH4 at 10 bar) and hydrogen at 77 K (1.91 wt % under 3 bar).     

High H2 uptake in Li-, Na-, K-metalated covalent organic frameworks and metal organic frameworks at 298 K

The Yaghi laboratory has developed porous covalent organic frameworks (COFs), COF102, COF103, and COF202, and metal-organic frameworks (MOFs), MOF177, MOF180, MOF200, MOF205, and MOF210, with ultrahigh porosity and outstanding H(2) storage properties at 77 K. Using grand canonical Monte Carlo (GCMC) simulations with our recently developed first principles based force field (FF) from accurate quantum mechanics (QM), we calculated the molecular hydrogen (H(2)) uptake at 298 K for these systems, including the uptake for Li-, Na-, and K-metalated systems. We report the total, delivery and excess amount in gravimetric and volumetric units for all these compounds. For the gravimetric delivery amount from 1 to 100 bar, we find that eleven of these compounds reach the 2010 DOE target of 4.5 wt % at 298 K. The best of these compounds are MOF200-Li (6.34) and MOF200-Na (5.94), both reaching the 2015 DOE target of 5.5 wt % at 298 K. Among the undoped systems, we find that MOF200 gives a delivery amount as high as 3.24 wt % while MOF210 gives 2.90 wt % both from 1 to 100 bar and 298 K. However, none of these compounds reach the volumetric 2010 DOE target of 28 g H(2)/L. The best volumetric performance is for COF102-Na (24.9), COF102-Li (23.8), COF103-Na (22.8), and COF103-Li (21.7), all using delivery g H(2)/L units for 1-100 bar. These are the highest volumetric molecular hydrogen uptakes for a porous material under these thermodynamic conditions. Thus, one can obtain outstanding H(2) uptakes with Li, Na, and K doping of simple frameworks constructed from simple, cheap organic linkers. We present suggestions for strategies for synthesis of alkali metal-doped MOFs or COFs.     

Bimetallo-radical carbon-hydrogen bond activation of methanol and methane

Carbon-hydrogen bond cleavage reactions of CH3OH and CH4 by a dirhodium(II) diporphyrin complex with a m-xylyl tether (.Rh(m-xylyl)Rh.(1)) are reported. Kinetic-mechanistic studies show that the substrate reactions are bimolecular and occur through the use of two Rh(II) centers in the molecular unit of 1. Second-order rate constants (T = 296 K) for the reactions of 1 with methanol (k(CH3OH) = 1.45 x 10-2 M-1 s-1) and methane (k(CH4) = 0.105 M-1 s-1) show a clear kinetic preference for the methane activation process. The methanol and methane reactions with 1 have large kinetic isotope effects (k(CH3OH)/k(CD3OD) = 9.7 +/- 0.8, k(CH4)/k(CD4) = 10.8 +/- 1.0, T = 296 K), consistent with a rate-limiting step of C-H bond homolysis through a linear transition state. Activation parameters for reaction of 1 with methanol (DeltaH = 15.6 +/- 1.0 kcal mol-1; DeltaS = -14 +/- 5 cal K-1 mol-1) and methane (DeltaH = 9.8 +/- 0.5 kcal mol-1; DeltaS = -30 +/- 3 cal K-1 mol-1) are reported.     

A Novel Bismuth‐Based Metal–Organic Framework for High Volumetric Methane and Carbon Dioxide Adsorption

Solvothermal reaction of H₄L (L=biphenyl‐3,3′,5,5′‐tetracarboxylate) and Bi(NO₃)₃ ? (H₂O)₅ in a mixture of DMF/MeCN/H₂O in the presence of piperazine and nitric acid at 100 °C for 10 h affords the solvated metal–organic polymer [Bi₂(L)_1.5(H₂O)₂] ? (DMF)_3.5 ? (H₂O)₃ (NOTT‐220‐solv). A single crystal X‐ray structure determination confirms that it crystallises in space group P2/c and has a neutral and non‐interpenetrated structure comprising binuclear {Bi₂} centres bridged by tetracarboxylate ligands. NOTT‐220‐solv shows a 3,6‐connected network having a framework topology with a {4 ? 6²}₂{4² ? 6⁵ ? 8⁸}{6² ? 8} point symbol. The desolvated material NOTT‐220a shows exceptionally high adsorption uptakes for CH₄ and CO₂ on a volumetric basis at moderate pressures and temperatures with a CO₂ uptake of 553 g L^?1 (20 bar, 293 K) with a saturation uptake of 688 g L^?1 (1 bar, 195 K). The corresponding CH₄ uptake was measured as 165 V(STP)/V (20 bar, 293 K) and 189 V(STP/V) (35 bar, 293 K) with a maximum CH₄ uptake for NOTT‐220a recorded at 20 bar and 195 K to be 287 V(STP)/V, while H₂ uptake of NOTT‐220a at 20 bar, 77 K is 42 g L^?1. These gas uptakes have been modelled by grand canonical Monte Carlo (GCMC) and density functional theory (DFT) calculations, which confirm the experimental data and give insights into the nature of the binding sites of CH₄ and CO₂ in this porous hybrid material.     

GCMC investigation into adamantane-based aromatic frameworks with diamond-like structure as high-capacity hydrogen storage materials

A new class of 3D adamantane-based aromatic framework (AAF) with diamond-like structure was computationally designed with the aid of density functional theory (DFT) calculation and molecular mechanics (MM) methods. The hydrogen storage capacities of these AAFs were studied by the method of grand canonical Monte Carlo (GCMC) simulations. The calculated pore sizes of three AAFs reveal that AAF-1 and AAF-2 belong to microporous materials, while AAF-3 is a member of mesoporous materials. The GCMC results reveal that at 77 K and 100 bar, AAF-3 exhibits the highest gravimetric hydrogen uptake of 29.50 wt%, while AAF-1 shows the highest volumetric hydrogen uptake of 63.04 g L(-1). In particular, the gravimetric hydrogen uptake of AAF-3 reaches the Department of Energy's target of 6 wt% at room temperature. The extraordinary performances of these new AAFs in hydrogen storage have made them enter the list of top hydrogen storage materials up to now.     

High pressure pyrolysis of toluene. 1. Experiments and modeling of toluene decomposition

The pyrolysis of toluene, the simplest methyl-substituted aromatic molecule, has been studied behind reflected shock waves using a single pulse shock tube. Experiments were performed at nominal high pressures of 27 and 45 bar and spanning a wide temperature range from 1200 to 1900 K. A variety of stable species, ranging from small hydrocarbons to single ring aromatics (principal soot precursors such as phenylacetylene and indene) were sampled from the shock tube and analyzed using standard gas chromatographic techniques. A detailed chemical kinetic model with 262 reactions and 87 species was assembled to simulate the stable species profiles (specifically toluene, benzene and methane) from the current high-pressure pyrolysis data sets and shock tube-atomic resonance absorption spectrometry (ARAS) H atom profiles obtained from prior toluene pyrolysis experiments performed under similar high-temperature conditions and lower pressures from 1.5 to 8 bar. The primary steps in toluene pyrolysis represent the most sensitive and dominant reactions in the model. Consequently, in the absence of unambiguous direct experimental measurements, we have utilized recent high level theoretical estimates of the barrierless association rate coefficients for these primary reactions, C6H5 + CH3 --> C6H5CH3 (1a) and C6H5CH2 + H --> C6H5CH3 (1b) in the detailed chemical kinetic model. The available data sets can be successfully reconciled with revised values for deltaH0f(298K)(C6H5CH2) = 51.5 +/- 1.0 kcal/mol and deltaH0f(298K)(C6H5) = 78.6 +/- 1.0 kcal/mol that translate to primary dissociation rate constants, reverse of 1a and 1b, represented by k(-1a,infinity) = (4.62 x 10(25))T(-2.53)exp[-104.5 x 10(3)/RT] s(-1) and k(-1b,infinity) = (1.524 x 10(16))T(-0.04)exp[-93.5 x 10(3)/RT] s(-1) (R in units of cal/(mol K)). These high-pressure limiting rate constants suggest high-temperature branching ratios for the primary steps that vary from 0.39 to 0.52 over the temperature range 1200-1800 K.     

Functionalizing porous aromatic frameworks with polar organic groups for high-capacity and selective CO2 separation: a molecular simulation study

Porous aromatic frameworks (PAFs) were recently synthesized with the highest surface area to date; one such PAF (PAF-1) has diamond-like structure with biphenyl building blocks and exhibits exceptional thermal and hydrothermal stabilities. Herein, we computationally design new PAFs by introducing polar organic groups to the biphenyl unit and then investigate their separating power toward CO(2) by using grand-canonical Monte Carlo (GCMC) simulations. Among these functional PAFs, we found that tetrahydrofuran-like ether-functionalized PAF-1 shows higher adsorption capacity for CO(2) at 1 bar and 298 K (10 mol per kilogram of adsorbent) and also much higher selectivities for CO(2)/CH(4), CO(2)/N(2), and CO(2)/H(2) mixtures when compared with the amine functionality. The electrostatic interactions are found to play a dominant role in the high CO(2) selectivities of functional PAFs, as switching off atomic charges would decrease the selectivity by an order of magnitude. This work suggests that functionalizing porous frameworks with tetrahydrofuran-like ether groups is a promising way to increase CO(2) adsorption capacity and selectivity, especially at ambient pressures.     

Kinetics and mechanism of methane, methanol, and dimethyl ether C-H activation with electrophilic platinum complexes

The relative rates of C-H activation of methane, methanol, and dimethyl ether by [(N-N)PtMe(TFE-d(3))](+) ((N-N) = ArN=C(Me)-C(Me)=NAr; Ar = 3,5-di-tert-butylphenyl, TFE-d(3) = CF(3)CD(2)OD) (2(TFE)) were determined. Methane activation kinetics were conducted by reacting 2(TFE)-(13)C with 300-1000 psi of methane in single-crystal sapphire NMR tubes; clean second-order behavior was obtained (k = 1.6 +/- 0.4 x 10(-3) M(-1) s(-1) at 330 K; k = 2.7 +/- 0.2 x 10(-4) M(-1) s(-1) at 313 K). Addition of methanol to solutions of 2(TFE) rapidly establishes equilibrium between methanol (2(MeOD)) and trifluoroethanol (2(TFE)) adducts, with methanol binding preferentially (K(eq) = 0.0042 +/- 0.0006). C-H activation gives [(N-N)Pt(CH(2)OD)(MeOD)](+) (4), which is unstable and reacts with [(RO)B(C(6)F(5))(3)](-) to generate a pentafluorophenyl platinum complex. Analysis of kinetics data for reaction of 2 with methanol yields k = 2.0 +/- 0.2 x 10(-3) M(-1) s(-1) at 330 K, with a small kinetic isotope effect (k(H)/k(D) = 1.4 +/- 0.1). Reaction of dimethyl ether with 2(TFE) proceeds similarly (K(eq) = 0.023 +/- 0.002, 313 K; k = 5.5 +/- 0.5 x 10(-4) M(-1) s(-1), k(H)/k(D) = 1.5 +/- 0.1); the product obtained is a novel bis(alkylidene)-bridged platinum dimer, [(diimine)Pt(mu-CH(2))(mu-(CH(OCH(3)))Pt(diimine)](2+) (5). Displacement of TFE by a C-H bond appears to be the rate-determining step for all three substrates; comparison of the second-order rate constants (k((methane))/k((methanol)) = 1/1.3, 330 K; k((methane))/k((dimethy)(l e)(ther)) = 1/2.0, 313 K) shows that this step is relatively unselective for the C-H bonds of methane, methanol, or dimethyl ether. This low selectivity agrees with previous estimates for oxidations with aqueous tetrachloroplatinate(II)/hexachloroplatinate(IV), suggesting a similar rate-determining step for those reactions.     

超临界甲烷在纳米材料中最适吸附压力的确定

用巨正则Monte Carlo (GCMC)方法模拟了超临界甲烷在层柱纳米材料中的吸附.模拟中,层柱纳米材料采用了柱子均匀分布在层板间的模型, 非极性分子甲烷采用Lennard Jones分子模型, 层板墙采用Steele的10 4 3模型, 流体分子与柱子的相互作用采用点 点 (site to site) 的方法计算.得到了甲烷的随着压力先增大后减小的超额吸附等温线.在T=207.3 K时,1.02、1.70和2.38 nm孔宽对应的最适操作压力 (即对应于最大吸附量时的操作压力) 分别为2.4、3.1和3.7 MPa.然而,在T=237.0 K时,1.02、1.70和2.38 nm孔宽对应的最适操作压力分别为2.9、3.6和4.9 MPa,分别比T=207.3 K时相同孔宽下对应的最适操作压力至少高0.5 MPa. 模拟结果表明, GCMC方法是研究材料吸附性能的一种强有力的工具.     

High-capacity hydrogen and nitric oxide adsorption and storage in a metal-organic framework

Gas adsorption experiments have been carried out on a copper benzene tricarboxylate metal-organic framework material, HKUST-1. Hydrogen adsorption at 1 and 10 bar (both 77 K) gives an adsorption capacity of 11.16 mmol H2 per g of HKUST-1 (22.7 mg g(-)1, 2.27 wt %) at 1 bar and 18 mmol per g (36.28 mg g(-)1, 3.6 wt %) at 10 bar. Adsorption of D2 at 1 bar (77 K) is between 1.09 (at 1 bar) and 1.20(at <100 mbar) times the H2 values depending on the pressure, agreeing with the theoretical expectations. Gravimetric adsorption measurements of NO on HKUST-1 at 196 K (1 bar) gives a large adsorption capacity of approximately 9 mmol g(-1), which is significantly greater than any other adsorption capacity reported on a porous solid. At 298 K the adsorption capacity at 1 bar is just over 3 mmol g(-1). Infra red experiments show that the NO binds to the empty copper metal sites in HKUST-1. Chemiluminescence and platelet aggregometry experiments indicate that the amount of NO recovered on exposure of the resulting complex to water is enough to be biologically active, completely inhibiting platelet aggregation in platelet rich plasma.     

Effect of the Ethanol/BTC Ratio on the Methane Uptake of Mechanochemically Synthesized MOF-199

We report on a detailed textural analysis of mechanochemically synthesized MOF-199 including N₂ adsorption-desorption and CO₂ adsorption isotherms data at 77 K and 273 K (up to atmospheric pressure), respectively, and CH₄ adsorption data at 298 K (up to 35 bar). We used the isotherm adsorption data to determine the micropore volume of the MOF-199 structures, to establish their methane uptake capacity and to understand how these properties depended on the Ethanol/BTC ratio used during the synthesis. The maximum methane uptake capacity for our specimens was recorded at 130 v/v at 35 bars. These results open an avenue for a better understanding of alternative manufacturing processes of MOF structures for gas storage applications.     

Highly selective carbon dioxide uptake by [Cu(bpy-n)2(SiF6)] (bpy-1 = 4,4'-bipyridine; bpy-2 = 1,2-bis(4-pyridyl)ethene)

A previously known class of porous coordination polymer (PCP) of formula [Cu(bpy-n)(2)(SiF(6))] (bpy-1 = 4,4'-bipyridine; bpy-2 = 1,2-bis(4-pyridyl)ethene) has been studied to assess its selectivity toward CO(2), CH(4), N(2), and H(2)O. Gas sorption measurements reveal that [Cu(bpy-1)(2)(SiF(6))] exhibits the highest uptake for CO(2) yet seen at 298 K and 1 atm by a PCP that does not contain open metal sites. Significantly, [Cu(bpy-1)(2)(SiF(6))] does not exhibit particularly high uptake under the same conditions for CH(4), N(2), and, H(2)O, presumably because of its lack of open metal sites. Consequently, at 298 K and 1 atm [Cu(bpy-1)(2)(SiF(6))] exhibits a relative uptake of CO(2) over CH(4) of ca. 10.5:1, the highest value experimentally observed in a compound without open metal sites. [Cu(bpy-2)(2)(SiF(6))] exhibits larger pores and surface area than [Cu(bpy-1)(2)(SiF(6))] but retains a high CO(2)/CH(4) relative uptake of ca. 8:1.     

Novel (3,4,6)-connected metal-organic framework with high stability and gas-uptake capability

A microporous and noninterpenetrated metal-organic framework [Cu(3)(L)(2)(DABCO)(H(2)O)]·15H(2)O·9DMF (1) has been synthesized using two different ligands, [1,1':3',1″-terphenyl]-4,4″,5'-tricarboxylic acid (H(3)L) and 1,4-diazabicyclo[2.2.2]octane (DABCO). As revealed by variable-temperature powder X-ray diffraction (VT-PXRD) measurements, N,N'-ditopic DABCO plays an important role for stabilization of the Cu-L framework. The three-dimensional framework of 1 exhibits high stability and excellent adsorption capacity for H(2) (54.3 mg g(-1) at 77 K and 20 bar), CO(2) (871 mg g(-1) at 298 K and 20 bar), CH(4) (116.7 mg g(-1), 99 cm(3) (STP) cm(-3) at 298 K and 20 bar), and n-pentane (686 mg g(-1) at 298 K and 1 bar). Interestingly, the excellent selectivity toward CO(2) over N(2) at ambient temperature (273 and 298 K) and 1 bar makes complex 1 possess practical application in gas separation and purification.     

Cubic and rhombohedral heterobimetallic networks constructed from uranium, transition metals, and phosphonoacetate: new methods for constructing porous materials

Four heterobimetallic U(vi)/M(ii) (M = Mn, Co, Cd) carboxyphosphonates have been synthesized. M(2)[(UO(2))(6)(PO(3)CH(2)CO(2))(3)O(3)(OH)(H(2)O)(2)]·16H(2)O (M = Mn(ii), Co(ii), and Cd(ii)) adopt cubic three-dimensional network structures with large cavities approximately 16 ? in diameter that are filled with co-crystallized water molecules. [Cd(3)(UO(2))(6)(PO(3)CH(2)CO(2))(6)(H(2)O)(13)]·6H(2)O forms a rhombohedral channel structure with hydrated Cd(ii) within the channels. The cubic compound (Co) displays differential gas absorption with a surface area for CO(2) uptake of 40 m(2) g(-1) at 273 K, and no uptake of N(2) at 77 K.     

Stability and reactivity of methane clathrate hydrates: insights from density functional theory

The sI methane clathrate hydrate consists of methane gas molecules encapsulated as dodecahedron (5(12)CH(4)) and tetrakaidecahedron (5(12)6(2)CH(4)) water cages. The characterization of the stability of these cages is crucial to an understanding of the mechanism of their formation. In the present work, we perform calculations using density functional theory to calculate interaction energies, free energies, and reactivity indices of these cages. The contributions from polarization functions to interaction energies is more than diffuse functions from Pople basis sets, though both functions from the correlation-consistent basis sets contribute significantly to interaction energies. The interaction energies and free energies show that the formation of the 5(12)CH(4) cage (from the 5(12) cage) is more favored compared to the 5(12)6(2)CH(4) cage (from the 5(12)6(2) cage). The pressure-dependent study shows a spontaneous formation of the 5(12)CH(4) cage at 273 K (P ≥ 77 bar) and the 5(12)6(2)CH(4) cage (P = 100 bar). The reactivity of the 5(12)CH(4) cage is similar to that of the 5(12) cage, but the 5(12)6(2)CH(4) cage is more reactive than the 5(12)6(2) cage.