Magneto-transport properties of dilute granular ferromagnets

We present magnetoresistance (MR) measurements performed on quench-condensed granular Ni thin films which are on the verge of electric continuity. In these systems, the electric conductivity is believed to be governed by the resistance between a very small number of grains. The films exhibit sharp resistance jumps as a function of magnetic field. We interpret these findings as being the result of magneto-mechanical distortions that occur in single grains which act as bottlenecks in the dilute percolation network. The observed features provide a unique measure of magnetostriction effects in nano-grain structures as well as being able to shed light on some of the properties of regular granular magnetic films.     

Highly Strained Si Films with Ultra-low Dislocation Density Grown on Virtual Substrates of Thin Thickness

By using compositionally graded SiGe films as virtual substrates, tensile strained Si films with the strain of 1.5% and the threading dislocation density less than 1.0 × 10^5 cm-2 are successfully grown in micron size windows by molecular beam epitaxy （MBE）. The thickness of the virtual substrates was only 33Onto. On the surface of the s-Si films no cross-hatched lines resulting from misfit dislocations could be observed. We attribute these results to the edge-induced strain relaxation of the epitaxial films in windows, and the patterned virtual substrates with compositionally graded SiGe films.     

Visible transmission through metal-coated colloidal crystals

Large-scale periodically structured metal films with enhanced optical transmission in visible frequencies were fabricated by depositing silver onto colloidal crystals. The obtained transmission properties are similar to those observed through periodical hole arrays in planar metal films. We have experimentally observed two enhanced transmission pass bands in visible frequencies in these metal films due to the excitation of surface plasmon polaritons. The peak positions of the pass bands depend on the size of the colloidal spheres. The transmission spectra highly depend on the incident angle for p-polarized light but are weak for s-polarized light. Our fabrication method provides a promising approach for the fabrication of large-scale low-cost plasmonic crystals with submicrometer periodicity.     

Magnetic force microscopy studies of domain walls in nickel and cobalt films

A magnetic force microscopy is used to examine the domain walls in nickel and cobalt films deposited by argon ion sputtering. Thin nickel films deposited at high substrate temperatures exhibit coexistent Bloch and Neel walls. Films grown at room temperature display alternative Bloch lines with cap switches. These films agglomerate to form grains after annealed at high temperatures. The film composed of larger grains behaves better nucleation implying magnetic domains of closure, while the film composed of smaller grains exhibits more defects implying alternative Bloch lines. We have also observed domain displacements and cap switches, which occur due to precipitation of particles in small grain size films. Stripe domains are observed for film thicknesses larger than 100 nm. They become zigzag cells when an external field of 1.5 T is applied perpendicular to the surface of the films. This experiment indicates that the domain sizes in thin films and the strip widths for thick films both depend on the square-root of the film thickness, which varies from 5 to 45 nm and from 100 to 450 nm, respectively.     

Structural changes of diamond-like carbon films due to atomic hydrogen exposure during annealing

We have deposited diamond-like carbon (DLC) films by radio-frequency magnetron sputtering, and have annealed the films under various conditions to investigate the effects of annealing on the structural properties by visible Raman spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy. The structural ordering of hydrogenated DLC films occurs during annealing below 400 °C in a vacuum and a hydrogen gas atmosphere, while unhydrogenated DLC films are not ordered during annealing even at 700 °C. On the other hand, the ordering and the decrease of the sp³ content are observed for both the films after annealing under an atomic hydrogen exposure. The ordering progresses as the annealing temperature and time are increased. The reduction of the film thickness after annealing is suppressed with increasing annealing temperature. The results suggest that both the preferential etching by atomic hydrogen and the hydrogen evolution encourage the structural changes under an atomic hydrogen exposure.     

Nanoscale formation mechanism of conducting filaments in NiO thin films

We have studied the nanoscale electrical properties of NiO thin films by using conducting atomic force microscopy (CAFM) to understand the mechanism of resistance change of the NiO thin films as we changed the applied voltage. We observed that inhomogeneous conducting filaments were generated by external voltage bias; in addition, some of the inhomogeneous conducting filaments were durable while some of them were not, and they disappeared. We deduced that the resistance change of the NiO thin films was related to inhomogeneous filamentary conducting paths generated by both Ni ions in thermodynamically unstable NiO and the existence of conducting filament segments generated by high voltage bias.     

Multilayer Au/TiO2Composite Films with Ultrafast Third-Order Nonlinear Optical Properties

We report on the ultrafast third-order optical nonlinearity in multilayer Au/TiO2 composite films fabricated on quartz substrates by pulsed laser deposition technique. The linear optical properties of the films are determined and optical absorption peaks due to surface plasmon resonance of Au particles are observed at about 590hm. The third-order optical nonlinearities of the films are investigated by z-scan method using a femtosecond laser （50 fs） at the wavelength of 800 nm. The sample showed fast nonlinear optical responses with nonlinear absorption coefficient and nonlinear refractive index being -3.66 × 10^-10 m/W and -2.95 × 10^-17 m^2/W, respectively. The results also show that the nonlinear optical effects increase with the increasing Au concentration in the composite films.     

记录薄膜Te—In—Sb光学性质的研究

采用高频溅射方法制成Te-In-Sb系统的非晶态薄膜.系统的研究了不同组分薄膜的透射、反射谱,及其在结晶过程中的变化.用透射电镜研究了Te-In-Sb薄膜的结构和晶化过程.分析了组分对薄膜的吸收系数、介电常数、光学能隙等光学性质的影响.并由此综合评价了Te-In—Sb系统中比较适合作为光盘介质的组成.     

Influence of Grain Size on Electrical and Optical Properties of InP Films

InP film samples were prepared by spray pyrolysis technique using aqueous solutions of InCl₃ and Na₂HPO₄, which were atomized with compressed air as carrier gas onto glass substrates at 500°C with different thicknesses of the films. It is found that the resistivity of the polycrystalline films strongly depends on the grain size. It is observed that the grain size of the films increase with the decrease of the energy band gap and strain of the film. The changes observed in the energy band gap and strain related to the film grain size of the films are discussed in detail.     

Swift heavy ion induced surface modifications in nano-crystalline Li-Mg ferrite thin films

The swift heavy ion (190 MeV Au¹⁴⁺) induced modifications in surface morphologies of the nanocrystals of ferrite thin films have been extensively studied through the images of atomic force microscopy (AFM). In most of the irradiated films significant features like, the ditch and dike structures, have been observed through out the surface. We try to explain the observed changes on the basis of thermal spike model followed by momentum transfer induced lateral mass transport. In addition to these changes some new and interesting features have been noticed after irradiation in 8F and 9F ferrite thin films. These new features are attributed to sputtering phenomenon due to the presence of defects like latent tracks.     

Electronic structure of GaN(0001)‐2 × 2 thin films grown by PAMBE

Gallium nitride thin films were grown on silicon carbide (0001) by plasma‐assisted molecular beam epitaxy (PAMBE). The samples were cooled down in nitrogen plasma and characterized in situ by reflection high energy electron diffraction (RHEED), photoelectron spectroscopy (XPS/UPS), and atomic force microscopy (AFM) revealing stoichiometric and smooth GaN films virtually free of contaminations. We present valence band data obtained by UPS with strong emission from surface states inside the fundamental band gap. These states and the observed 2 × 2 surface reconstruction are highly sensitive towards residual molecules. Once these surface states have disappeared the original state could not be recovered by surface preparation methods underlining the necessity of in situ investigations on as‐grown surfaces. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of annealing on structural and electrical properties of the Li–Mn–O thin films, prepared by high frequency RF magnetron sputtering

Li–Mn–O thin film cathode materials are prepared by high frequency (27.12 MHz) RF magnetron sputtering. The high RF frequency gives higher deposition rates without compromising on the quality of the films. This investigation focuses on the effects of post-annealing on the micro-structural, morphological and electrical properties of Li–Mn–O films. It is observed that with the increase of annealing temperature the crystallinity as well as the electrical conductivity of the films increases. The films annealed at 600–700 °C are found to have high structural perfection and good electrical properties.     

Polyelectrolytes tethered to a free surface

Several attempts have been already carried out in order to tether charged chains by an end at a free fluctuating surface. We review here most of these attempts and focus on how close the physics of charged brushes can be investigated by such an approach. We first describe results about films of charged-neutral diblock copolymers spread at the surface of water. Results can be mostly rationalized in terms of charged brushes although additional structurations and fluctuations of the interface can be observed. The latter deformations are also observed when adsorbed layers of charged-neutral diblock copolymers are considered. At last, we examine how free suspended films of charged-neutral diblock copolymers can be viewed as two opposing charged brushes, both in terms of thickness and pressure. Received 9 May 2000     

Photosensitivity of nanocrystalline ZnO films grown by PLD

We have studied the properties of ZnO thin films grown by laser ablation of ZnO targets on (0 0 0 1) sapphire (Al₂O₃), under substrate temperatures around 400 °C. The films were characterized by different methods including X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and atomic force microscopy (AFM). XPS analysis revealed that the films are oxygen deficient, and XRD analysis with θ-2θ scans and rocking curves indicate that the ZnO thin films are highly c-axis oriented. All the films are ultraviolet (UV) sensitive. Sensitivity is maximum for the films deposited at lower temperature. The films deposited at higher temperatures show crystallite sizes of typically 500 nm, a high dark current and minimum photoresponse. In all films we observe persistent photoconductivity decay. More densely packed crystallites and a faster decay in photocurrent is observed for films deposited at lower temperature.     

Infrared electroluminescence from a Si MOS structure with Ge in the oxide

We report on room-temperature infrared electroluminescence (EL) from metal-oxide-semiconductor devices made from Si. We compare the luminescence from RF sputtered oxide films containing SiO₂ with and without Ge by using a composite target and luminescence from a SiO₂ layer made by rapid thermal oxidation. The sputtered films were annealed in the temperature range 600-900 °C. This densifies the films and is likely to reduce the concentration of defects. A luminescence peak located around 1150-1170 nm is observed at current densities as low as 0.1 A/cm². The corresponding photon energy is close to that of the Si band gap. In addition, we observe several broad luminescence bands in the range 1000-1750 nm. These bands get stronger with Ge in the SiO₂ film. Some of these bands have previously been suggested and are directly associated with Ge. Since we observe that the intensity is correlated with the presence of Ge while the mere presence of the bands is not, we discuss the EL bands being due to defects which concentration is influenced by Ge in the oxide.     

Strain relaxation of CdTe films growing on lattice-mismatched substrates

We have deposited CdTe films by laser-assisted epitaxy approach and investigated the influence of substrate and film thickness on the film properties. Grown on Si(001), GaAs(001), and quartz substrates; the CdTe films exhibit preferential orientation along the cubic CdTe(111) direction. When the films are thin (<500 nm), a blueshift of the band gap and splitting of valence bands were observed. These results are attributed to the existence of residual strains induced by mismatch of the film lattice constant with that of the substrate, and by their difference in thermal expansion coefficients. The bulk band-gap energy of 1.5 eV was achieved on the surface of thick CdTe films grown on Si(001) substrate, indicating that strain was almost completely relaxed in this case. Our results demonstrate that by a proper selection of substrate and film thickness it is possible to grow film semiconductors with band gap approaching those of bulk crystals.     

Magnetism in very thin films of permalloy measured by spin polarized cascade electrons

The spin polarizationP of the low energy cascade electrons excited with a primary unpolarized electron beam is measured with ultrathin films of permalloy (Ni₈₀Fe₂₀) as a function of film thickness, external magnetic field, and temperatureT. Surface adsorbates of small concentrations of less than 10% of a monolayer can change the Curie point and the saturation value ofP ₀(T0) by as much as 30%. The Ta-substrate induces a magnetically dead region in permalloy. Conventional spin wave theory cannot account for the observed smallT-dependence of the magnetizationM. Films on a nonmagnetic substrate are compared to similar films coupled to bulk permalloy over an interface of Ta. TheT-dependence ofM with the coupled films can be explained by spin wave theory. At lowT, the films coupled to the bulk exhibit a faster decrease ofM than the uncoupled films. We propose that this thermal stabilization of the magnetization in very thin ferromagnetic films is due to quenching of the long wavelength spin modes.     

Optical and Magnetic Properties of Fe-Doped GaN Diluted Magnetic Semiconductors Prepared by MOCVD Method

Fe-doped GaN thin films are grown on c-sapphires by metal organic chemical vapour deposition method （MOCVD） Crystalline quality and phase purity are characterized by x-ray diffraction and Raman scattering measurements. There are no detectable second phases formed during growth and no significant degradation in crystalline quality as Fe ions are doped. Fe-related optical transitions are observed in photoluminescence spectra. Magnetic measurements reveal that the films show room-temperature ferromagnetic behaviour. The ferromagnetism may originate from carrier-mediated Fe-doped GaN diluted magnetic semiconductors or nanoscale iron clusters and FeN compounds which we have not detected.     

Anomalies of attenuation and phase velocity of surface acoustic waves in YBa2Cu3O7‒δ thin films in the vicinity of Tc

We present measurements of the attenuation and phase velocity of surface acoustic waves in thin YBa₂Cu₃O films as a function of temperature, in magnetic fields up to 3.6 T applied parallel to the c-axis of the films. We have observed anomalies in both, the attenuation and the phase velocity in the vicinity of the superconducting critical temperature which do not depend on the magnetic field. Possible origins of these anomalies, observed, to our knowledge, for the first time in YBa₂Cu₃O thin films, are discussed and compared to bulk acoustic wave experiments. We present a kind of feedback technique for surface acoustic waves which improves the sensitivity of this type of measurement. The actual sensitivity limits are mentioned. Received: 7 August 1997 / Revised: 7 November 1997 / Accepted: 17 November 1997     

Spray pyrolysis deposition of ZnO thin films on FTO coated substrates from zinc acetate and zinc chloride precursor solution at different growth temperatures

ZnO thin films were fabricated using zinc chloride and zinc acetate precursors by the spray pyrolysis technique on FTO coated glass substrates. The ZnO films were grown in different deposition temperature ranges varying from 400 to 550 °C. Influences of substrate temperature and zinc precursors on crystal structure, morphology and optical property of the ZnO thin films were investigated. XRD patterns of the films deposited using chloride precursor indicate that (1 0 1) is dominant at low temperatures, while those deposited using acetate precursor show that (1 0 1) is dominant at high temperatures. SEM images show that deposition temperature and type of precursor have a strong effect on the surface morphology. Optical measurements show that ZnO films are obviously influenced by the substrate temperatures and different types of precursor solutions. It is observed that as temperature increases, transmittance decreases for ZnO films obtained using zinc chloride precursor, but the optical transmittance of ZnO films obtained using zinc acetate precursor increases as temperature increases.