Silver modified magnetic carbon nanotubes composite as a selective solid phase extractor for preconcentration and determination of trace mercury ions in water solution

A magnetic composite of silver/iron oxides/carbon nanotubes (Ag/Fe₃O₄/CNTs) was synthesized and used as an adsorbent for the preconcentration of mercury ions in water solutions at room temperature (25°C) in this study. The silver nanoparticles were supported on the magnetic CNTs. The modification enabled the composite had not only a high adsorption capacity for mercury ions (Hg²⁺) but also the magnetic isolation properties. A fast, sensitive, and simple method was successfully developed for the preconcentration and determination of trace amount of Hg²⁺ in water using the synthesized nanocomposite as adsorbent. The mercury concentration was determined by an atomic fluorescence spectrometer (AFS). The experimental conditions such as pH value, extraction temperature, extraction time, sample volume, eluent composition and concentration, sorbent amount, and coexisting ions were investigated for the optimization. A 500 mL of sample volume resulted in a preconcentration factor of 125. When a 200 mL of sample was employed, the limit of detection for Hg²⁺ was as low as 0.03 ng mL^?1with relative standard deviation of 4.4% at 0.1 ng mL^?1 (n = 7). The ease of synthesis and separation, the good adsorption capacity, and the satisfactory recovery will possibly make the composite an attractive adsorbent for the preconcentration of ultratrace Hg²⁺ in waters.     

Reactivity of sugar cane bagasse as a natural solid phase extractor for selective removal of Fe(III) and heavy-metal ions from natural water samples

This work introduces the feasibility of using sugar cane bagasse (SCB) – a sugar cane industry waste – as a selective solid phase extractor for Fe(III). The order of metal uptake capacities in μmol g^?1 for the extraction of six tested metal ions from aqueous solution using static technique is Fe(III) > Cu(II) > Pb(II) > Zn(II) > Cd(II) > Co(II). Since SCB exhibits remarkable binding characteristics for Fe(III), special interest was devoted for optimizing its uptake and studying its selectivity properties under static and dynamic conditions. In this respect, batch experiments were carried out at the pH range 1.0–4.0, initial concentration of metal ion (10–100 μmol), weight of phase (25, 50, 75, 100, 125 and 150 mg) and shaking time (10, 30, 45, 60, 90, 120 and 150 min). FT-IR spectra of SCB before and after uptake of Fe(III) were recorded to explore the nature of the functional groups responsible for binding of Fe(III) onto the studied natural biosorbent. The equilibrium data were better fitted with Langmuir model (r² = 0.985) than Freundlich model (r² = 0.934). Moreover, Fe(III) sorption was fast and completed within 60 min. The adsorption kinetics data were best fitted with the pseudo-second-order type. As a view to find a suitable application of SCB based on its unique property as a benign sorbent, it was found that, Fe(III) spiked natural water samples such as doubly distilled water (DDW), drinking tap water (DTW), natural drinking water (NDW), ground water (GW) and Nile River water (NRW) was quantitatively recovered (>95.0%) using batch and column experiments, with no matrix interferences.     

Alumina modified by dimethyl sulfoxide as a new selective solid phase extractor for separation and preconcentration of inorganic mercury(II)

Dimethyl sulfoxide (DMSO) was simply immobilized to neutral alumina via quite strong hydrogen bonding between sulfoxide oxygen and surface alumina hydroxo groups. The produced alumina-modified dimethyl sulfoxide (AMDMSO) solid phase (SP)-extractor experienced high thermal and medium stability. Moreover, the small and compact size of DMSO moiety permit high surface coverage evaluated to be 2.1 ± 0.1 mmol g⁻¹ of alumina. Hg(II) uptake was 1.90 mmol g⁻¹(distribution coefficient log K_d = 5.658) at pH 1.0 or 2.0, 1.68 mmol g⁻¹ (log K_d = 4.067) at pH 3.0 or 4.0 while the metal ions Ca(II), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Cd(II) and Pb(II) showed low values 0.513-0.118 mmol g⁻¹ (log K_d < 3.0) in the pH range 4.0-7.0. A mechanism was suggested to explain the unique uptake of Hg(II) ions by binding as neutral and chloroanionic species predominate at pH values ≤ 3.0 of a medium rich in chloride ions. A direct and fast batch separation mode was achieved successfully to retain selectively Hg(II) in presence of other eight coexisting metal ions. Thus, Hg(II) was completely retained; Ca(II), Co(II), Ni(II) and Cd(II) were not retained, while Pb(II), Cu(II), Zn(II) and Fe(III) exhibited very low percentage retention evaluated to be 0.42, 0.49, 1.4 and 5.43%, respectively. The utility of the new modified alumina sorbent for concentrating of ultratrace amounts of Hg(II) was performed by percolating 2 l of doubly distilled water, drinking tap water, and Nile river water spiked with 10 ng/l over 100 mg of the sorbent packed in a minicolumn used as a thin layer enrichment bed prior to the determination by CV-AAS. The high recovery values obtained (98.5 ± 0.5, 98.5 ± 0.5 and 103.0 ± 1.0) based on excellent enrichment factor 1000, along with a good precision (R.S.D.% 0.51-0.97%, N = 3) demonstrate the accuracy and validity of the new modified alumina sorbent for preconcentrating ultratrace amounts of Hg(II) with no matrix interference.     

Preparation,characterization and applications of polyurethane foam functionalized with resorcinol for quantitative separation and determination of silver(I) and mercury(II) from tap and wastewater

A stable chelating resin matrix was prepared by covalently linking resorcinol with polyurethane foam matrix through a –N=N– group. Preconcentration and determination of trace Ag⁺ and Hg²⁺ ions from samples of different origin, using Res-PUF, were studied. Various conditions influencing the sorption of these metal ions onto Res-PUF were optimized. The kinetics of sorption of the Ag⁺ and Hg²⁺ by Res-PUF were found to be fast, reached equilibrium in few minutes (5–10?min) and followed a first-order rate equation with an overall rate constant k in 0.102 and 0.267/min, respectively. Study of the variation of the sorption of the tested metal ions with temperature yielded average values for ΔG, ΔH and ΔS of ?3.94, ?22.02 and ?58.37, respectively. The mean free sorption energy (E) computed from the Dubinin–Radushkevich (D–R) isotherm was found to be equal to 8.91 kJ/mol, which reflects the chelation sorption process. The capacities of the foam material were 0.15 and 0.07?mmol/g for Ag⁺ and Hg²⁺, respectively. Preconcentration factors of?>?50 were achieved (RSD?≈?5.99). The proposed preconcentration procedure was applied successfully to the determination of trace metal ions in natural and wastewater samples.     

Preconcentration and separation of iron, zinc, cadmium and mercury, from waste water using Nile blue a grafted polyurethane foam

The present work describes a novel method for the incorporation of Nile blue A into polyurethane foam matrix. This foam material was found to be very suitable for the extraction of metal ions from aqueous solutions. The characterization of Nile blue A grafted foam and the effect of halide concentration, pH, shaking time, extraction isotherm and capacity have been investigated. This foam material was found to be suitable for the separation and preconcentration of iron (III), zinc (II), cadmium (II) and mercury (II) from waste water. The extraction was accomplished in (15-20) minutes. Iron was separated from acid medium (2-4 M HCl), zinc from (3-5 M HCl), cadmium from (4-6 M HCl) as thiocyanate complexes and mercury was separated from (1-2 M HCl) as chloride.     

Selective separation of silver(I) and mercury(II) ions in natural water samples using alumina modified thiouracil derivatives as new solid phase extractors

A simple and reliable solid-phase extraction (SPE) method has been developed to synthesise two new sorbents: 6-propyl-2-thiouracil and 5,6-diamino-2-thiouracil physically loaded onto alumina surface, phases I and II, respectively. The synthesis of these new phases has been confirmed by IR-spectroscopy. The surface concentrations of the organic moieties were determined to be 0.182 and 0.562 mmol g^?1 for phases I and II, respectively. The evaluation of the selectivity and metal uptake properties incorporated in these two alumina phases were also studied and discussed for 10 different metal ions: Ca(II), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Cd(II), Hg(II), Pb(II) and Ag(I) under different controlling factors. The data obtained clearly indicated that the new SP-extractors have the highest affinity for retention of Hg(II) ions. Selective separation of Hg(II) from Ag(I) as one of the most interfering ion, in addition to the other eight coexisting metal ions under investigation, was achieved successfully using the new sorbents at pH = 9.0 under static conditions. Therefore, Hg(II) exhibits major retention percentage (100.0%) using phase I or II. However, Ag(I) exhibits minor retention percentage equal to 1.33% using phase I and 0.67% using phase II. On the other hand, the retention percentage of the other eight metal ions ranged (0.0–3.08%) using phase I and (0.0–1.54%) using phase II at the same pH. The new phases were applied for separation and determination of trace amounts of Hg(II) and Ag(I) spiked natural water samples using cold vapour atomic absorption spectroscopy and atomic absorption spectroscopy with no matrix interference. The high recovery values of Hg(II) and Ag(I) obtained using phases I and II were ranged 98.9 ± 0.1–99.2 ± 0.05% along with a good precision (RSD% 0.01–0.502%, N = 3) demonstrate the accuracy and validity of the new sorbents for separation and determination of Hg(II) and Ag(I).     

Ultrasonic-assisted supramolecular solvent-based liquid phase microextraction of mercury as 1-(2-pyridylazo)-2-naphthol complexes from water samples

A separation-preconcentration method based on supramolecular solvent ultrasonic-assisted liquid-phase microextraction (Ss-USA-LPME) for spectrophotometric determination of mercury as 1-(2-pyridylazo)-2-naphthol (PAN) chelates has been established. Red coloured Hg(II)-PAN hydrophobic complex was extracted into the supramolecular phase (1-decanol/THF) at pH 9.5. The extract was separated from aqueous phase by centrifugation, diluted with ethanol and determined by UV–Vis spectrophotometer at λ_max = 560 nm. The influences of important analytical parameters such as pH, amount of PAN, 1-decanol and THF, sample volume and matrix effects for the quantitative recoveries were examined and optimised. Under the optimised experimental conditions, the amount of ligand, 1-decanol and THF were 1.0 × 10^–4 M, 200 µL and 300 µL, respectively. The optimum time of ultrasonic bath and centrifugation were found as 2 min and 5 min. A linear calibration graph was obtained linearly in the concentration ranges of 8.3–1000 µg L^?1. The preconcentration factor was obtained as 20. The limit of detection (LOD) was 2.6 µg L^?1 with the relative standard deviation (RSD) of 2.4% for mercury (C = 100 µg L^?1, n = 7). The validity of the developed Ss-USA-LPME technique was checked with a certified reference material of NIST 1641d. The presented method has been successfully applied to the determination of mercury in water samples.     

Double-walled carbon nanotubes as a solid phase extractor for separation-preconcentration of traces of gold from geological and water samples

In this work, a solid phase extraction method has been developed using a column filled with double-walled carbon nanotubes (DWNT) for preconcentration-separation of gold(III) ions prior to their flame atomic absorption spectrometric determination. Gold(III) ions were quantitatively recovered on DWNT in 1.0?mol?L^?1 HCl. The influences of the analytical conditions including eluent type, sample volume, etc. on the recoveries of gold(III) ions were examined. The effects of concomitant ions were also investigated. The detection limits for gold(III) based on 3σ was calculated as 1.5?µg?L^?1. The procedure presented in this paper was applied to the gold content of a number of water, geological and anodic slime samples with successful results.     

A solid phase extraction using a chelate resin immobilizing carboxymethylated pentaethylenehexamine for separation and preconcentration of trace elements in water samples

A chelate resin immobilizing carboxymethylated pentaethylenehexamine (CM-PEHA resin) was prepared, and the potential for the separation and preconcentration of trace elements in water samples was evaluated through the adsorption/elution test for 62 elements. The CM-PEHA resin could quantitatively recover various elements, including Ag, Cd, Co, Cu, Fe, Ni, Pb, Ti, U, and Zn, and rare earth elements over a wide pH range, and also Mn at pH above 5 and V and Mo at pH below 7. This resin could also effectively remove major elements, such as alkali and alkaline earth elements, under acidic and neutral conditions. Solid phase extraction using the CM-PEHA resin was applicable to the determination of 10 trace elements, Cd, Co, Cu, Fe, Mn, Mo, Ni, Pb, V, and Zn, in certified reference materials (EnviroMAT EU-L-1 wastewater and ES-L-1 ground water) and treated wastewater and all elements except for Mn in surface seawater using inductively coupled plasma atomic emission spectrometry. The detection limits, defined as 3 times the standard deviation for the procedural blank using 500 mL of purified water (50-fold preconcentration, n = 8), ranged from 0.003 μg L⁻¹ (Mn) to 0.28 μg L⁻¹ (Zn) as the concentration in 500 mL of solution.     

Pretreatment of water samples using UV irradiation-peroxodisulfate for the determination of total mercury

Potassium peroxodisulfate (14 g l⁻¹, 25 ml) has been observed to readily oxidize water under UV irradiation (30 W mercury arc tube), even at room temperature. The reaction is complete in 20 min, producing oxygen in stoichiometric amounts. The reaction was applied to pretreatment for the determination of total mercury by cold vapor atomic absorption spectrometry (AAS).The response of mercury(II) chloride by the UV irradiation method was higher than that by the standard permanganate method (95 °C, 2 h). The conversion efficiency of mercury by the UV irradiation method, the standard method and by non-treatment was found to be 100, 93.6 and 85.0%, respectively. The study is also applied to methylmercury, ethylmercury and phenylmercury chlorides.     

Critical comparison of two standard digestion procedures for the determination of total mercury in natural water samples by cold vapour atomic absorption spectrometry

Two pretreatment procedures for total mercury determinations in natural water samples were compared. The first, the Swedish Standard method (DP1), involves digestion of water in the presence of concentrated nitric acid at 120°C and under pressure for 30 min. In the West German Standard method (DP2), small volumes of nitric and sulphuric acids, permanganate and peroxodisulphate are added to the sample, and digestion proceeded at 50°C in an ultrasonic bath. Mercury was determined after both digestion procedures using a modified cold vapour atomic absorption spectrometric method, in which mercury generated on addition of a reducing agent is collected and subsequently atomized in a platinum-lined graphite furnace. The efficacy of the two digestion procedures was tested using various standard organic mercury compounds and it was found that only DP2 provided quantitative recoveries. Purification of the reagents required by DP2 was achieved using a mercury-selective ion-exchange resin, Chelite S, resulting in blank levels below 1.5 ng Hg l^?1. Both methods were applied to the determination of total mercury in an unpolluted marsh water sample, giving 2.0 ng Hg l^?1 (DP1) and 2.7 ng Hg l^?1 (DP2). The West German Standard digestion procedure (DP2) is recommended for the determination of total mercury in natural water samples.     

New solid phase extractors for selective separation and preconcentration of mercury (II) based on silica gel immobilized aliphatic amines 2-thiophenecarboxaldehyde Schiff’s bases

2-Thiophenecarboxaldhyde is chemically bonded to silica gel surface immobilized monoamine, ethylenediamine and diethylenetriamine by a simple Schiff’s base reaction to produce three new SP-extractors, phases (I-III). The selectivity properties of these phases toward Hg(II) uptake as well as eight other metal ions: Ca(II), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Cd(II) and Pb(II) were extensively studied and evaluated as a function of pH of metal ion solution and equilibrium shaking time by the batch equilibrium technique. The data obtained clearly indicate that the new SP-extractors have the highest affinity for retention of Hg(II) ion. Their Hg(II) uptake in mmol g⁻¹ and distribution coefficient as log K_d values are always higher than the uptake of any other metal ion along the range of pH used (pH 1.0-10.0). The uptake of Hg(II) using phase I was 2.0 mmol g⁻¹ (log K_d 6.6) at pH 1.0 and 2.0. 1.8 mmol g⁻¹ (log K_d 4.25), 1.6 mmol g⁻¹ (log K_d 3.90) and 1.08 mmol g⁻¹ (log K_d 3.37) at pH 3.0, 5.0 and 8.0, respectively. Selective separation of Hg(II) from the other eight coexisting metal ions under investigation was achieved successfully using phase I at pH 2.0 either under static or dynamic conditions. Hg(II) was completely retained while Ca(II), Co(II) and Cd(II) ions were not retained. Ni(II), Cu(II), Zn(II), Pb(II) and Fe(III) showed very low percentage retention values to be 0.74, 0.97, 3.5 and 6.3%, respectively. Moreover, the high recovery values (95.5 ± 0.5, 95.8 ± 0.5 and 99.0% ± 1.0) of percolating two liters of doubly distilled water, drinking tap water and Nile river water spiked with 5 ng/l of Hg(II) over 100 mg of phase I packed in a minicolumn and used as a thin layer enrichment bed demonstrate the accuracy and validity of the new SP-extractors for preconcentration of the ultratrace amount of spiked Hg(II) prior to the determination by borohydride generation atomic absorption spectrometry (AAS) with no matrix interference. The detection limit (3σ) for Hg(II) based on enrichment factor 1000 was 4.75 pg/ml. The precision (R.S.D.) obtained for different amounts of mercury was in the range 0.52-1.01% (N = 3) at the 25-100 ng/l level.     

Sulfhydryl-functionalised magnetic nanoparticles as sorbent in dispersive solid-phase extraction for the rapid enrichment of mercury species from natural water samples

The sulfhydryl-functionalised core-shell Fe₃O₄@SiO₂ magnetic nanoparticles (Fe₃O₄@SiO₂–RSH MNPs)-based dispersive solid-phase extraction method was developed. The goal of this method is the extraction of mercury species from natural water samples. An interesting aspect of the method is that, thanks to the spontaneously aggregate, the MNPs with a sub-30-nm-size range could be fast and efficiently extracted by 0.45 μm pore size mixed cellulose esters membrane filter. Thus, the elution step can be conducted by passing small amounts eluent through the MNPs on the membrane. It is also found that addition of Ag⁺ to water sample could improve the elution efficiency, and furthermore, minimises the matrix effects during the extraction of mercury species from natural water samples. The feasibility of the method was studied, and extraction efficiency was evaluated. The results showed that, calculated at 5 ng/L spiked concentration levels, absolute recoveries were 89.4%, 91.9% and 64.2%, and enrichment factors (EFs) were 596, 613 and 428, for inorganic mercury, methylmercury and ethylmercury, respectively. The high EFs were achieved in 5 min of overall extraction time. The method was applied to groundwater and river water samples. The results showed that its suitability for use in fast extracting trace levels of mercury species from natural water samples.     

Solvothermal synthesis of EDTA-functionalized magnetite-carboxylated graphene oxide nanocomposite as a potential magnetic solid phase extractor of p-phenylenediamine from environmental samples

The use of carboxylated graphene oxide (CGO) in the removal of organic pollutants from aquatic life is a recent and significant issue. In this study, EDTA-functionalized magnetite-carboxylated graphene oxide nanocomposite (EDTA-MCGO) was first used for the adsorptive removal of p-phenylenediamine (PDA) from industrial wastewaters. Based on the great surface area of the magnetic nanocomposite and the huge number of carboxyl groups from CGO and EDTA, multiple interactions to adsorb PDA can be anticipated. The maximum adsorption capacity of EDTA-MCGO was 994.75?mg g^?1 at pH 7.8 and this value was decreased to 94.7% after seven cycles. The adsorption process was spontaneous and fits the pseudo-second-order kinetic model. PDA strongly deposited on the EDTA-MCGO surface via different electrostatic interactions and hydrogen bonding. The PDA removal efficiency from different environmental wastewaters was 98.6?±?0.6%. All the results demonstrate that the EDTA-MCGO nanocomposite is a potential magnetic extractor of aromatic contaminants from aquatic life.GRAPHICAL ABSTRACT     

Evaluation of polychlorotrifluoroethylene as sorbent material for on-line solid phase extraction systems: determination of copper and lead by flame atomic absorption spectrometry in water samples

Polychlorotrifluoroethylene (PCTFE) in the form of beads was applied, as packing material for flow injection on-line column preconcentration and separation systems coupled with flame atomic absorption spectrometry (FAAS). Its performance characteristics were evaluated for trace copper determination in environmental samples. The on-line formed complex of metal with diethyldithiophosphate (DDPA) was sorbed on the PCTFE surface. Isobutyl methyl ketone (IBMK) at a flow rate of 2.8 mL min⁻¹ was used to elute the analyte complex directly into the nebulizer-burner system of spectrophotometer. The proposed sorbent material reveal, excellent chemical and mechanical resistance, fast adsorption kinetics permitting the use of high sample flow rates up to 15 mL min⁻¹ without loss of retention efficiency. For copper determination, with 90 s preconcentration time the sample frequency was 30 h⁻¹, the enhancement factor was 250, which could be further improved by increasing the loading (preconcentration) time. The detection limit (3s) was c_L = 0.07 μg L⁻¹, and the precision (R.S.D.) was 1.8%, at the 2.0 μg L⁻¹ Cu(II) level. For lead determination, the detection limit was c_L = 2.7 μg L⁻¹, and the precision (R.S.D.) 2.2%, at the 40.0 μg L⁻¹ Pb(II) level. The accuracy of the developed method was evaluated by analyzing certified reference materials and by recovery measurements on spiked natural water samples.     

An electropolymerized aniline-based fiber coating for solid phase microextraction of phenols from water

An aniline-based polymer was electrochemically prepared and applied as a new fiber coating for solid phase microextraction (SPME) of some priority phenols from water samples. The polyaniline (PANI) film was directly electrodeposited on the platinum wire surface in sulfuric acid solution using cyclic voltammetry (CV) technique. The efficiency of new coating was investigated using a laboratory-made SPME device and gas chromatography with flame ionization detection for the extraction of some phenols from the headspace of aqueous samples. The scanning electron microscopy (SEM) images showed the homogeneity and the porous surface structure of the film. The results obtained proved the ability of this polymer as a suitable SPME fiber coating for trapping the selected phenols. Influential parameters affecting the extraction process were optimized and an extraction time of 50 min at 50 °C gave maximum efficiency, when the aqueous sample was saturated with NaCl and adjusted at pH 2. This new coating can be prepared easily in a reproducible manner and it is rather inexpensive and stable against most of organic solvents. The PANI thickness can be precisely controlled by the number of CV cycles. At the optimum conditions, the R.S.D. for a double distilled water spiked with phenol and chlorophenols at ppb level were 4.8-17% (n = 3) and detection limits for the studied compounds were between 0.69 and 3.7 ng ml⁻¹, except for phenol and 4-chlorophenol. The optimized method was successfully applied to some real-life water samples.     

Electrosynthesis of a new selective chelating agent for solid phase extraction of Ni(II) from water samples: characterisation and analytical applications

A new polymer as a selective chelating agent for separation and preconcentration of nickel ions from water samples was prepared by electropolymerisation of 4-nitrophenol. Electrosynthesis was carried out on the lead cathode in aqueous sodium acetate solution. The electrode-product is a dark-brown powder, insoluble in water but soluble in methanol, N,N-dimethylformamide (DMF) and tetrahydrofuran (THF). The electrode-product was characterised by differential scanning calorimetry (DSC), gel permeation chromatography (GPC), FT-IR, ¹H-NMR, cyclic voltammetry (CV) and UV-Vis spectrometry. A proper mechanism and structure of the prepared polymer was suggested. A few drops of methanolic solution of electrode-product formed a blue complex with nickel ions in an aqueous medium in the pH range of 6 to 10. This new chelating reagent was used as a coating material on activated charcoal and applied for solid phase extraction of trace amounts of nickel ions from natural and waste waters. The effect of different parameters such as type of eluent, elution conditions, sample volume and sample flow rate and mass of coating material were studied. In the presence of co-existing ions, no significant interferences were observed. Under the optimal conditions, limits of detection (LOD) and quantification (LOQ) were 0.32 and 1 µg L^?1 Ni(II), respectively. The proposed method was used for determination of Ni(II) in some lagoons south of the Caspian Sea and waste waters of factories. The validity of this method was confirmed by the comparison of the obtained results with the results of ICP-OES.     

Optimization of a new resin, Amberlyst 36, as a solid-phase extractor and determination of copper(II) in drinking water and tea samples by flame atomic absorption spectrometry

A new simple and reliable method has been developed to separate and preconcentrate trace copper ion in drinking water and tea samples for subsequent measurement by flame atomic absorption spectrometry (FAAS). The copper ions are adsorbed quantitatively during passage of aqueous solutions through Amberlyst 36 cation exchange resin. After the separation and preconcentration stage, the analyte was eluted with a potassium cyanide solution and determined by FAAS. Different factors including pH of sample solution, sample volume, amount of resin, flow rate of aqueous solution, volume and concentration of eluent, and matrix effects for preconcentration were examined. The analytical figures of merit for the determination of copper are as follows: analytical detection limit (3 sigma), 0.26 microg/L; precision (RSD), 3.1% for 100 microg/L; enrichment factor, 200 (using 1000 mL of sample solution and 5 mL of eluent); time of analysis, 3.5 h (for obtaining enrichment factor of 200); capacity of resin, 125 mg/g. The method was applied for copper determination by FAAS in tap water, commercial natural spring water, commercial treated drinking water, and commercial tea bag sample. The accuracy of the method is confirmed by analyzing tea leaves (GBW 07605). The results demonstrated good agreement with the certified values.     

Facile synthesis of a novel nanocomposite for determination of mercury and copper ions in food and water samples

This paper describes the modification of sodium aluminum silicate hydrate by 3-bromo-5-chlorosalicylaldehyde to form a new composite. Furthermore, X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), Transmission electron microscopy (TEM), CHN elemental analysis, Nitrogen gas sorption analyzer, and Scanning electron microscopy (SEM) tools were used for characterizing the synthesized composite. The XRD pattern of the synthesized composite shows a halo at 2Θ = 25°, confirming the destruction of the crystalline structure of the nanomaterial owing to the association with an organic substance. The synthesized composite was utilized for the removal and preconcentration of mercury and copper ions from water and food samples. The maximum adsorption capacity of the synthesized composite towards mercury and copper ions is 107.53 and 130.89 mg/g, respectively. In addition, the relative standard deviation was less than 3 %, showing excellent reproducibility. The dynamic analytical ranges are 0.8–380 μg/L and 1.00–550 μg/L for copper and mercury ions, respectively. The preconcentration factor is 10.     

Development of a broad selective molecularly imprinted polymers-based solid phase extraction of contraceptive drug levonorgestrel from water samples

A broad selective molecularly imprinted polymers-based solid phase extraction (MISPE) for levonorgestrel (LNG) from water samples was developed. Using LNG as a template molecule, acrylamide (AA) as functional monomer, ethylene glycol dimethacrylate (EGDMA) as linking agent and bulk polymerisation as a synthetic method, the molecularly imprinted polymers (MIPs) were synthesised and characterised. The MIPs displayed a high specific rebinding for LNG with the imprinting factor of 3.71. The Scatchard analysis showed that there was at least one class of binding site for LNG formed in the MIPs with the dissociation constant of 8.046?µg?mL^?1. The results of selectivity testing indicated that the MIPs also exhibited high cross-reactivity with structurally related compounds (estrone, methylprednisolone and ethinyl estradiol), but no recognition with non-structurally related compound (indomethacin), suggesting that the MIPs could be used as a broad recognition absorbent. MISPE column was prepared by packing MIPs particles into a common SPE cartridge. The MISPE extraction conditions including loading, washing and eluting solutions were carefully optimised. Water samples spiked with LNG were extracted by MISPE column and detected by high-performance liquid chromatography. The recoveries were found to be 79.97?～?132.79% with relative standard deviations (RSD) of 1.92?～?10.43%, indicating the feasibility of the prepared MIPs for LNG extraction.