多壁碳纳米管固相萃取净化-高效液相色谱法测定猪肉和鸡肉中的磺胺多残留

建立了多壁碳纳米管为吸附剂的固相萃取净化-高效液相色谱-紫外检测测定猪肉和鸡肉中多种磺胺类药物多残留的方法。样品采用乙腈提取,多壁碳纳米管固相萃取净化,NaH₂PO₄缓冲溶液（pH 5.5~6.0）溶解上样,5%（v/v）丙酮-正己烷淋洗,丙酮-二氯甲烷（1：1,v/v）洗脱。色谱分离以50 mmol/L NaH₂PO₄-乙腈（7：3,v/v）为流动相,方法的线性范围为0.01~1.00 mg/L,线性相关系数大于0.998,检出限（LOD）为0.003 mg/L,定量限（LOQ）为0.01 mg/L。在0.02~0.2 mg/kg添加范围内,9种磺胺类药物的回收率高于70%,RSD低于8%,表明多壁碳纳米管对磺胺类药物具有较强的吸附富集能力。该方法简便、准确可用于动物组织及产品中磺胺药物残留的检测。     

Cigarette filter as sorbent for on-line coupling of solid-phase extraction to high-performance liquid chromatography for determination of polycyclic aromatic hydrocarbons in water

An on-line solid-phase extraction (SPE) protocol using the cigarette filter as sorbent coupled with high-performance liquid chromatography (HPLC) was developed for simultaneous determination of trace naphthalene (NAPH), phenanthrene (PHEN), anthracene (ANT), fluoranthene (FLU), benzo(b)fluoranthene (BbF), benzo(k)fluoranthene (BkF), benzo(a)pyrene (BaP), and benzo(ghi)perylene (BghiP) in water samples. To on-line interface solid-phase extraction to HPLC, a preconcentration column packed with the cigarette filter was used to replace a conventional sample loop on the injector valve of the HPLC for on-line solid-phase extraction. The sample solution was loaded and the analytes were then preconcentrated onto the preconcentration column. The collected analytes were subsequently eluted with a mobile phase of methanol-water (95:5). HPLC with a photodiode array detector was used for their separation and detection. The detection limits (S/N = 3) for preconcentrating 42 mL of sample solution ranged from 0.9 to 58.6 ng L(-1) at a sample throughput of 2 samples h(-1). The enhancement factors were in the range of 409-1710. The developed method was applied to the determination of trace NAPH, PHEN, ANT, FLU, BbF, BkF, BaP and BghiP in local river water samples. The recoveries of PAHs spiked in real water samples ranged from 87 to 115%. The precisions for nine replicate measurements of a standard mixture (NAPH: 4.0 microg L(-1), PHEN: 0.40 microg L(-1), ANT: 0.40 microg L(-1), FLU: 2.0 microg L(-1), BbF: 1.6 microg L(-1), BkF: 2.0 microg L(-1), BaP: 2.0 microg L(-1), BghiP: 1.7 microg L(-1)) were in the range of 1.2-5.1%.     

Preparation and evaluation of a mixed-bed immunoaffinity column for selective purification of sixteen sulfonamides in pork muscle

This paper describes the preparation of a novel mixed-bed immunoaffinity chromatography (IAC) column by coupling four monoclonal antibodies against different sulfonamides (SAs) to Sepharose 4B. The IAC column can be used to simultaneously extract and purify 16 SAs in pork muscle. The dynamic column capacities for all SAs in mixed standard solution were between 312 and 479 ng/mL gel. After simple extraction and IAC cleanup, the sample solution can be directly injected for liquid chromatography-ultraviolet analysis. The recoveries of SAs from spiked samples at levels of 25, 50 and 100 μg/kg ranged from 83.3 to 103.1% with variation coefficient less than 8.6%. The comparison of IAC with liquid-liquid extraction and solid phase extraction indicated that IAC has better purification effect and needs less organic solution than conventional methods, thus it would be an ideal method for selective purification of SAs in pork muscle.     

固相萃取-高效液相色谱同时测定沼液中3种四环素类和6种磺胺类抗生素

建立了一种用固相萃取高效液相色谱法同时测定沼液中3种四环素类(TCs)和6种磺胺类(SAs)抗生素的分析方法.样品经Na2 EDTA提取,固相萃取小柱富集净化,甲醇洗脱后,用高效液相色谱-紫外检测法测定.检测波长270 nm,柱温25℃,流动相为乙腈-o.1％甲酸水溶液,采用等度洗脱.9种待测组分实现了基线分离,线性范围为0.02～10 mg·L-1.沼液实际样品的加标回收率范围为74.2％～102.9％.方法的检出限为2.8～21.0 μg·L-1.应用此方法对南京地区分别以猪粪、牛粪、鸡粪为发酵原料的3个沼气工程的沼液样品进行分析测定,结果表明在3种不同发酵原料的沼液环境中,不同频率地检出了四环素类和磺胺类抗生素,浓度范围为21.7～125.5μg·L-1.该方法具有准确可靠、快速简便等优点,可用于沼液中上述9种组分的同时测定.     

固相萃取-高效液相色谱法测定动物肉组织中磺胺类药物的残留

建立了一种快速、灵敏、环保的固相萃取-反相高效液相色谱同时分析动物肉组织中5种磺胺类药物残留的方法。将样品加入到盛有无水硫酸钠的离心管中,再用乙酸乙酯提取;提取液经氨基固相萃取柱净化后,用1.5%（体积分数）乙酸乙醇溶液洗脱。洗脱液用高效液相色谱分离,二极管阵列检测器检测,外标法定量。5种磺胺类药物的线性关系良好,磺胺二甲基嘧啶(SM2)、磺胺间甲氧嘧啶(SMM)、磺胺甲唑(SMZ)的线性范围均为30～5000 μg/L,磺胺二甲氧嘧啶(SDM)、磺胺喹啉(SQ)的线性范围均为60～5000 μg/L。2种动物肉组织(鸡肉、猪肉)中5种磺胺类药物的加标回收率在73.2%至97.3%范围内,当添加水平为50 μg/kg时,加标回收率的相对标准偏差在2.5%至11.6%范围内;SM2,SMM和SMZ的检测限（S/N=3）和定量限（S/N=10）分别为3 μg/kg和10 μg/kg,SDM和SQ的检测限和定量限分别为7 μg/kg和25 μg/kg。     

羧基化多壁碳纳米管固相萃取-液相色谱-串联质谱法测定环境水体中四溴双酚A和双酚A

建立了羧基化碳纳米管固相萃取-液相色谱-串联质谱联用检测环境水体中四溴双酚A和双酚A的方法。比较了多壁碳纳米管、C60和羧基化多壁碳纳米管作为固相吸附剂对水体中四溴双酚A和双酚A的吸附效率。固相萃取浓缩后的样品经Thermo Scientific Hypersil C18色谱柱（150 mm×4.6 mm,3 μm）分离,采用串联质谱负离子模式进行检测。结果表明,四溴双酚A和双酚A在0.02~1.0 mg/L范围内具有良好的线性关系（r²≥0.99）,空白样品中的检出限（S/N=3）分别为0.04 μg/L和0.2 μg/L。将所建立的方法应用于实际环境水体中四溴双酚A和双酚A的检测,添加回收率在82%~99%之间,精密度小于5.0%,该方法可用于复杂环境样品中痕量四溴双酚A和双酚A的检测。     

固相萃取-高效液相色谱法同时测定牛奶中残留的9种磺胺类药物

建立了同时测定牛奶中残留的9种磺胺类药物的固相萃取-高效液相色谱分析方法。牛奶样品经磷酸盐缓冲液稀释后高速离心去除脂肪,过C18小柱,用水淋洗,甲醇洗脱,洗脱液经氮气吹干后用乙酸乙酯溶解,并过氨基固相萃取小柱净化,用正己烷及水淋洗,以甲醇-乙腈-水（含1%乙酸）(体积比为1∶1∶8)洗脱,洗脱液用于高效液相色谱分析。采用Inertsil ODS-3 C18柱分离,以水-乙酸和甲醇-乙腈为流动相进行梯度洗脱,二极管阵列检测器检测,外标法定量。9种磺胺类药物标准曲线的线性回归系数均在 0.9999 以上,线性范围为25～5000 μg/L,检出限为1.7～2.8 μg/L,定量限为5.7～9.2 μg/L。在10,20,40 μg/L 添加水平下的添加回收率为72.1%~88.3%,相对标准偏差为2.3%～5.0%。该方法具有快速、灵敏的特点,符合现行兽药残留分析的要求。     

Validation Method for the Determination of Sulfonamide Residues in Bovine Milk by HPLC

A simple, rapid, sensitive and reliable high-performance liquid chromatographic method for the simultaneous determination of eight sulfonamides (SAs) in bovine milk was developed (sulfadiazine, sulfathiazole, sulfamethazine, sulfamethoxypyridazine, sufamonomethoxine, sulfamethoxazole, sulfadimethoxine and sulfaquinoxaline) in bovine milk was developed. Samples were prepared by extraction with ethyl acetate and cleaning-up with an anion solid-phase extraction (SPE) column. Analytical separation was performed on an Inertsil ODS-3 column with photodiode-array detection at 270 nm under gradient condition. The whole procedure was evaluated according to the European Commission Decision 2002/657/EC. Specificity, decision limit (CCα), detection capacity (CCβ), trueness and precision were determined during the validation process. It was found that the analytes were isolated from spiked samples with good recoveries between 70.5 and 89.0%. The used analytical conditions allow to successively separating all the tested sulfonamides with good limit of detection between 0.8 and 1.5 μg L⁻¹.     

Ionic liquid-based microwave-assisted dispersive liquid-liquid microextraction and derivatization of sulfonamides in river water, honey, milk, and animal plasma

The ionic liquid-based microwave-assisted dispersive liquid-liquid microextraction (IL-based MADLLME) and derivatization was applied for the pretreatment of six sulfonamides (SAs) prior to the determination by high-performance liquid chromatography (HPLC). By adding methanol (disperser), fluorescamine solution (derivatization reagent) and ionic liquid (extraction solvent) into sample, extraction, derivatization, and preconcentration were continuously performed. Several experimental parameters, such as the type and volume of extraction solvent, the type and volume of disperser, amount of derivatization reagent, microwave power, microwave irradiation time, pH of sample solution, and ionic strength were investigated and optimized. When the microwave power was 240 W, the analytes could be derivatized and extracted simultaneously within 90 s. The proposed method was applied to the analysis of river water, honey, milk, and pig plasma samples, and the recoveries of analytes obtained were in the range of 95.0-110.8, 95.4-106.3, 95.0-108.3, and 95.7-107.7, respectively. The relative standard deviations varied between 1.5% and 7.3% (n=5). The results showed that the proposed method was a rapid, convenient and feasible method for the determination of SAs in liquid samples.     

High-performance liquid chromatographic methods for the determination of sulfonamides in tissue, milk and eggs.

In the last decade, significant research has been done to improve the existing high-performance liquid chromatographic (HPLC) methods and also towards developing simple, reliable and sensitive HPLC methods for sulfonamides in meat, milk and eggs. The replacement of solvent extraction with solid-phase extraction or matrix solid-phase dispersion techniques is a step forward. Significant improvements in sensitivity have been achieved. This review concentrates on HPLC methods for the determination of sulfonamides in foods of animal origin published after 1980. The existing methods are critically evaluated and suggestions for future research are made.     

On-line coupling of dynamic microwave-assisted extraction to solid-phase extraction for the determination of sulfonamide antibiotics in soil

A rapid technique based on dynamic microwave-assisted extraction (DMAE) coupled on-line with solid-phase extraction (SPE) was developed for the determination of sulfonamides (SAs) including sulfadiazine, sulfameter, sulfamonomethoxine and sulfaquinoxaline in soil. The SAs were first extracted with acetonitrile under the action of microwave energy, and then directly introduced into the SPE column which was packed with neutral alumina for preconcentration of analytes and clean-up of sample matrix. Subsequently, the SAs trapped on the alumina were eluted with 0.3% acetic acid aqueous solution and determined by liquid chromatography-tandem mass spectrometry. The DMAE parameters were optimized by the Box-Behnken design. Maximum extraction efficiency was achieved using 320 W of microwave power; 12 mL of extraction solvent and 0.8 mL min⁻¹ of extraction solvent flow rate. The limits of detection and quantification obtained are in the range of 1.4-4.8 ng g⁻¹ and 4.6-16.0 ng g⁻¹ for the SAs, respectively. The mean values of relative standard deviation of intra- and inter-day ranging from 2.7% to 5.3% and from 5.6% to 6.7% are obtained, respectively. The recoveries of SAs obtained by analyzing four spiked soil samples at three fortified levels (20 ng g⁻¹, 100 ng g⁻¹ and 500 ng g⁻¹) were from 82.6 ± 6.0% to 93.7 ± 5.5%. The effect of standing time of spiked soil sample on the SAs recoveries was examined. The recoveries of SAs decreased from (86.3-101.9)% to (37.6-47.5)% when the standing time changed from one day to four weeks.     

Evaluation of carbon nanotubes as a solid-phase extraction adsorbent for the extraction of cephalosporins antibiotics, sulfonamides and phenolic compounds from aqueous solution

The adsorptive potential of carbon nanotubes (single-walled carbon nanotubes and multi-walled carbon nanotubes) for solid-phase extraction of three groups of highly polar compounds (namely cephalosporins antibiotics, sulfonamides and phenolic compounds) was tested in this article. The analytes were strongly retained by the carbon nanotubes. And acceptable recoveries were obtained with the addition of ammonium acetate into eluents. The effects of solution pH on the recoveries of the antibiotics and phenolic compounds were examined. To check the retention abilities of three groups of compounds on carbon nanotubes, fixed amount of each analyte was added to different volumes (up to 500 mL) of aqueous solution, and then extracted by the sorbents. Comparative studies showed that the carbon nanotubes were much superior to C₁₈ for the extraction of the highly polar analytes. For the cephalosporins antibiotics and sulfonamides, the carbon nanotubes showed stronger retention capability than graphitized carbon blacks, but for some of the phenolic compounds graphitized carbon blacks seemed to be more suitable, indicating different retention mechanisms of these analytes. To further assess the enrichment ability of carbon nanotubes for highly polar compounds, the solid-phase extraction method of multi-walled carbon nanotubes packed cartridge was well developed, and the sulfonamides were used as model compounds. Under the optimal procedures, the detection limits of sulfonamides were in the range of 27-38 ng L⁻¹. The spiked recoveries from several real water samples obtained for sulfathiazole and sulfadiazine ranged from 55% to 79% and 72% to 92%, respectively, while the recoveries of sulfapyridine and sulfamethazine were in the range of 85-102%.     

Application of NaClO-treated multiwalled carbon nanotubes as solid phase extraction sorbents for preconcentration of trace 2,4-dichlorophenoxyacetic acid in aqueous samples

Multiwalled carbon nanotubes functionalized by oxidation of original multiwalled carbon nanotubes with NaClO were prepared and their application as solid phase extraction sorbent for 2,4-dichlorophenoxyacetic acid (2,4-D) was investigated systemically, and a new method was developed for the determination of trace 2,4-D in water samples based on extraction and preconcentration of 2,4-D with solid phase extraction columns packed with NaClO-treated multiwalled carbon nanotubes prior to its determination by HPLC. The optimum experimental parameters for preconcentration of 2,4-D, including the column activating conditions, the amount of the sorbent, pH of the sample, elution composition, and elution volume, were investigated. The results indicated 2,4-D could be quantitatively retained by 100 mg NaClO-treated multiwalled carbon nanotubes at pH 5, and then eluted completely with 10 mL 3:1 (v/v) methanol-ammonium acetate solution (0.3 mol/L). The detection limit of this method for 2,4-D was 0.15 μg/L, and the relative standard deviation was 2.3% for fortified tap water samples and 2.5% for fortified riverine water sample at the 10 μg/L level. The method was validated using fortified tap water and riverine water samples with known amount of 2,4-D at the 0.4, 10, and 30 μg/L levels, respectively.     

固相萃取-高效液相色谱-串联质谱法同时测定土壤中氟喹诺酮、四环素和磺胺类抗生素

建立了固相萃取-高效液相色谱-串联质谱法同时检测土壤中氟喹诺酮类、四环素类和磺胺类18种抗生素的分析方法。土样经含50%乙腈的磷酸盐缓冲液(pH=3)提取后,以SAX-HLB串联小柱净化富集,在HPLC/MS/MS多反应监测模式下进行定性及定量分析。添加浓度为200和50μg/kg时,土壤中氟喹诺酮类、四环素类、磺胺类的加标回收率分别为67.2%～89.0%,62.2%～85.4%和55.8%～97.4%;其相对标准偏差为1.1%～17.2%。以3倍信噪比估算出氟喹诺酮类、四环素类、磺胺类的检出限分别为3.4～8.9μg/kg,0.56～0.91μg/kg和0.07～1.85μg/kg。应用此方法检测6种不同类型土壤样品,结果表明,污灌区土壤中检出有抗生素,浓度为1.72～119.6μg/kg。     

Improved high-performance liquid chromatographic procedure for the determination of lasalocid in chicken tissues and egg using polymeric and porous graphitic carbon columns.

A high-performance liquid chromatographic (HPLC) method for the determination of the ionophore coccidiostat lasalocid in poultry muscle and eggs was developed. The drug was extracted from tissue with acetonitrile. The extract was partitioned between saturated salt and carbon tetrachloride and the organic layer evaporated to dryness. Clean-up was by solid-phase extraction on a silica column. HPLC analysis was carried out on either a polymeric PLRP-S or a porous graphitic carbon Hypercarb column with a basic mobile phase and fluorescence detection with excitation at 310 nm and emission at 420-430 nm. Average recoveries from poultry muscle at the 0.002, 0.010 and 0.050 mg kg-1 levels were 65.7, 72.0 and 77.9%, respectively. Average recoveries from egg at the 0.010 and 0.100 mg kg-1 levels were 76.2 and 76.4%, respectively.     

Miniaturized fiber-in-tube solid-phase extraction as the sample preconcentration method for microcolumn liquid-phase separations

Miniaturized fiber-in-tube solid-phase extraction (fiber-in-tube SPE) has been developed as a solventless sample preconcentration technique for microcolumn liquid-phase separation methods. Short capillaries packed with polymer filaments were employed as the extraction tube and the preconcentration power for phthalates in aqueous solutions was studied. On the basis of the successful on-line coupling of this preconcentration method with liquid chromatography (LC), a more miniaturized extraction cartridge, which is installed in the rotor of the micro-injector, has been developed. With a modified commercially available valve, on-line coupling of this sample preconcentration method to capillary electrochromatography (CEC) was also investigated.     

Hexafluoroisopropanol-induced coacervation in aqueous mixed systems of cationic and anionic surfactants for the extraction of sulfonamides in water samples

Hexafluoroisopropanol (HFIP)-induced coacervation in aqueous mixed systems of catanionic surfactants of dodecyltrimethylammonium bromide (DTAB) and sodium dodecyl sulfate (SDS) was described in detail, and its application in the extraction of strongly polar sulfonamides (SAs) was investigated. With 10 % (v/v) HFIP inclusion, coacervation formation and two-phase separation occur in a wide range of SDS/DTAB mole ratios (88:12～0:100 mol/mol) and total surfactant concentrations (10～200 mmol/L). The interactions between HFIP and DTAB play an important role in coacervation formation. The HFIP-induced SDS–DTAB coacervation extraction proves to be an efficient method for the extraction and preconcentration of SAs. Both hydrophobic interaction and polar interactions (hydrogen–bond, electrostatic, and π-cation) contribute to the distribution of SAs into coacervate phase. The proposed HFIP-induced SDS–DTAB coacervation extraction combined with HPLC–UV was employed for the extraction and quantitative determination of SAs in environmental water samples. Limits of detection were 1.4～2.5 ng mL^?1. Excellent linearity with correlation coefficients from 0.9990 to 0.9995 was obtained in the concentration of 0.01～10 μg mL^?1. Relative recoveries were in the range of 93.4～105.9 % for analysis of the lake, underground, and tap water samples spiked with SAs at 0.01, 1.0, and 10 μg/mL, respectively. Relative standard deviations were 0.7～3.2 % for intraday precision and 1.3～4.6 % for interday precision (n?=?3). Concentration factors were 17～49 for three water samples spiked with 0.01 μg/mL SAs. The results demonstrate that the proposed extraction method is feasible for the preconcentration and determination of trace SAs in real water samples. Graphical abstract

?     

Eco-friendly and Cleaner Process Using Online Microwave-assisted Steam Extraction Coupled with Solid-phase Extraction for Trace Analysis of Sulfonamides in Animal Feed

An environmentally friendly method for extracting sulfonamides(SAs) residues from animal feed was described and applied. The method used online microwave-assisted steam extraction coupled with solid phase extraction(MASE-SPE), which was followed by the analysis using high performance liquid chromatography-mass spectrometry(HPLC-MS/MS). The SAs residues were extracted successively with water steam under microwave irradiation, and thus directly introduced into an SPE column containing cation-exchange resin. The SAs were then eluted with methanol-ammonia(90:10, volume ratio) from the SPE column and followed by HPLC-MS/MS. The limits of detection(LODs) for the analytes ranged from 0.24 ng/g to 0.49 ng/g. The limits of quantification(LOQs) ranged from 0.82 ng/g to 1.63 ng/g. Average recoveries of SAs were 76.3%-92.1%. The developed method was a reliable and environmentally friendly alternative to previous methods with respect to time, solvent and labor consumption for the analysis of SAs in animal foodstuffs.     

Determination of thiol compounds by solid-phase extraction using multi-walled carbon nanotubes as adsorbent coupled with high-performance liquid chromatography-fluorescence detection

Microchimica Acta - We describe a method for solid-phase extraction of biogenic thiols using multi-walled carbon nanotubes as adsorbent, and their subsequent determination via HPLC and fluorescence...     

A nanocomposite made from conducting organic polymers and multi-walled carbon nanotubes for the adsorption and separation of gold(III) ions

We describe a new method for the separation and preconcentration of traces of Au(III) in environmental samples. Sorbents made from modified multiwalled carbon nanotubes and conducting polymers (PANI and PEDOT) were used for solid-phase extraction. The Au(III) ions are adsorbed as a result of the interaction with the electron pairs of =N- and -S- groups. Effects of pH value, flow rate and volume of sample, type, volume and concentration of eluent, and the adsorption capacity were investigated. The maximum adsorption capacity of MWCNTs/PANI and MWCNTs/PEDOT are 159 and 176?mg?g^?1, and the detection limits of this method are below 0.3 and 0.5?ng?mL^?1, respectively. The procedure was successfully applied to the determination of traces of Au(III) in a reference material and in environmental samples.