High sensitivity of positron annihilation lifetime to time and pressure effects in gas-exposed polymers

Positron annihilation lifetime (PAL) experiments are performed in polycarbonate (PC) exposed to CO₂ and He gases as a function of time and pressure. In PC/CO₂ systems, hole size and fraction reduced from PAL data increase as a function of CO₂ pressure and exposure time. Significant hysteresis in positron lifetime data is observed during CO₂ abasorption/desorption. In PC/He systems, no variation is observed. Hole size distribution in the CO₂-exposed polymers is found to be significantly broader than in unexposed samples. The high sensitivity of PAL results to CO₂ exposure of PC is thought to relate to the microstructural changes in the polymer matrix, such as penetrant plasticization, gas hydrostatic pressure effect, and molecular filling and creation of holes.     

Effect of CO2 exposure on free volumes in polystyrene studied by positron annihilation spectroscopy

Free‐volume properties, size and distribution, in amorphous polystyrene exposed to CO₂ gases have been measured as a function of pressure to 800 psi (5.5 MPa), of time, and of temperature using positron annihilation lifetime spectroscopy. The free volume increases significantly and its distribution broadens as a function of pressure. The free volume relaxes as a function of time with a characteristic time of 15 h, and 5.7 h for 400, and 800 psi, respectively, after depressurizing under vacuum. A portion of free volume created by CO₂ exposure remains permanently in the polymer after CO₂ exposure. The glass transition temperature decreases significantly as a function of CO₂ pressure from the free‐volume data and is compared with the differential scanning calorimeter results. The observed free‐volume variations as a function of pressure, time, and temperature are discussed in terms of hole expansion, creation, free‐volume relaxation, plasticization, and hole filling in amorphous polymers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 388–405, 2008     

Measurement of free-volume hole size distribution in Nafion-117 using positron annihilation spectroscopy

We report a new result of free-volume hole size distribution in water and ethanol-swollen Nafion-117 polymer. With the increase in water content, free-volume hole size decreases, but overall the volume fraction increases. The hole size distribution in dry polymer is seen to be distinctly different from hydrated membranes. The narrow and symmetric distribution in hydrated membrane as compared to dry membrane is believed to be a consequence of crosslinking due to cluster formation. In alcohol-swollen membranes, on the other hand, not only are the free-volume size and fraction seen to be higher, the hole size distribution is seen to be broader compared to dry or hydrated membranes, indicating the effect of penetration of alcohol into the hydrophobic backbone region. We have also examined our results vis-a-vis reported gas diffusion studies in Nafion in the framework of existing free-volume model. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 983–989, 1998     

On the ionic conductivity of polymer electrolytes in terms of hole fraction

A theoretical model to interpret the conductivity of ions through polymer electrolytes is established in terms of the temperature and pressure‐dependent hole fraction computed from Simha‐Somcynsky hole theory. The model successfully linearizes the logarithm of PPG and PEG conductivity data with NaCF₃SO₃ in a 20:1 ratio for a broad range of temperature and pressure. The conductivity parameter and transmission coefficient with an additive hole fraction constant are discussed and compared for both species. The derivative of the logarithm of conductivity with respect to the hole fraction decreases inversely with the hole fraction and saturates at about 0.08 and 0.12 hole fractions for PPG and PEG, respectively. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2249–2254, 2008     

Compressed‐gas‐induced crystallization in tert‐butyl poly(ether ether ketone)

tert‐Butyl‐substituted poly(ether ether ketone) (tBuPEEK), which does not undergo crystallization with thermal annealing, crystallizes readily when treated with compressed CO₂. The dissolved CO₂ causes a reduction in the glass‐transition temperature of the polymer–gas system and enhances the chain mobility of the macromolecules, thereby bringing about crystallization. In the presence of CO₂, crystallization is increasingly favored with increasing CO₂ pressure and treatment temperature. The melting point of tBuPEEK crystals increases linearly with the CO₂ pressure applied in the treatment, indicating an increase in the order and/or size of the crystals. The extent of crystallinity increases when small amounts of methanol or dichloromethane are used as a cosolute with CO₂. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1505–1512, 2001     

Measurement and prediction of solubilities and diffusion coefficients of carbon dioxide in starch–water mixtures at elevated pressures

The solubility and diffusion coefficient of carbon dioxide in intermediate‐moisture starch–water mixtures were determined both experimentally and theoretically at elevated pressures up to 16 MPa at 50 °C. A high‐pressure decay sorption system was assembled to measure the equilibrium CO₂ mass uptake by the starch–water system. The experimentally measured solubilities accounted for the estimated swollen volume by Sanchez–Lacombe equation of state (S‐L EOS) were found to increase almost linearly with pressure, yielding 4.0 g CO₂/g starch–water system at 16 MPa. Moreover, CO₂ solubilities above 5 MPa displayed a solubility increase, which was not contributed by the water fraction in the starch–water mixture. The solubilities, however, showed no dependence on the degree of gelatinization (DG) of starch. The diffusion coefficient of CO₂ was found to increase with concentration of dissolved CO₂, which is pressure‐dependent, and decrease with increasing DG in the range of 50–100%. A free‐volume‐based diffusion model proposed by Areerat was employed to predict the CO₂ diffusivity in terms of pressure, temperature, and the concentration of dissolved CO₂. S‐L EOS was once more used to determine the specific free volume of the mixture system. The predicted diffusion coefficients showed to correlate well with the measured values for all starch–water mixtures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 607–621, 2006     

An in situ study of plasticization of polymers by high-pressure gases

A high-pressure differential scanning calorimetric technique is described for studying polymer plasticization by compressed gases at pressures to 100 atm. The in situ measurements avoid problems due to gas desorption encountered with conventional DSCs, thus providing an accurate way to determine the change in glass transition temperature, T_g, with pressure, p. The entire T_g–p curve can be established in less than 2 days. The glass transition was observed as a sharp step in the case of 100–200-μm thin samples, whereas thicker samples gave a broad transition; highly reproducible results were obtained for the thin samples. For PS–CO₂, the measured T_gs under various pressures were found to be in good agreement with literature values. Results for the systems PS–HFC134a, PVC–CO₂, and PC–CO₂ are also reported. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 977–982, 1998     

Analysis of polystyrene surface properties on thin film bonding under carbon dioxide pressure using nanoparticle embedding technique

A gold nanoparticle embedding technique is used to determine how vacuum and pressured carbon dioxide (CO₂) affect polystyrene (PS) thin film properties. The pressured CO₂ greatly increased the gold nanoparticle embedding depth, possibly due to a low cohesive energy density near the film surface. For the monodisperse PS used in this study (M_n = 214,000), two spin‐coated thin films with intimate contact can be bonded below the bulk glass transition temperature (T_g) under CO₂ pressure when the embedded depth is larger than half of the gyration radius of PS molecules. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1535–1542, 2009     

Sorption and diffusion of carbon dioxide in wood‐fiber/polystyrene composites

In this study, sorption and diffusion of carbon dioxide (CO₂) in wood‐fiber/polystyrene composites were investigated. The effects of gas pressure and fiber content on the solubility and diffusion coefficients were evaluated. A statistical analysis indicated that pressure is more important than fiber content in determining the solubility and diffusivity of CO₂. An increase in saturation pressure causes an increase in the solubility and diffusion coefficients, whereas inclusion of the fibers decreases both of these properties. Models were developed to predict the uptake and diffusion coefficients of CO₂ in the composite samples as functions of pressure and fiber content. A theoretical model based on Henry's law and the Langmuir equation compared favorably to the experimental data for CO₂ solubility. This dual mode model also described both the transient sorption and desorption data, but only if the concentration‐dependent value of diffusivity was treated as a history‐dependent parameter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 723–735, 2002     

Dual mode model for mixed gas permeation of CO2, H2, and N2 through a dry chitosan membrane

Dry chitosan is an excellent candidate for facilitated transport membranes that can be utilized in industrial applications, such as fuel cell operations and other purification processes. This article is the first to report temperature effects on transport properties of CO₂, H₂, and N₂ in a gas mixture typical of such applications. At a feed pressure of 1.5 atm, CO₂ permeabilities increased (0.381–26.1 barrers) at temperatures of 20–150 °C with decreasing CO₂/N₂ (19.7–4.55) and CO₂/H₂ (3.14–1.71) separation factors. The pressure effect on solubilities and permeabilities were fitted to the extended dual mode model and its corresponding mixed gas permeation model. The dual mode and transport parameters, the sorption heats and the activation energies of Henry's and Langmuir's regimes and their pre‐exponential parameters were determined. The Langmuir's capacity constants were utilized to estimate chitosan's glass transition temperature (CO₂: 172 °C, N₂: 175 °C, and H₂: 171 °C). The activation energies of diffusion in the Henry's law and Langmuir regimes were dependent on the collision diameter of the gases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2620–2631, 2007     

Suppression of CO2-plasticization by semiinterpenetrating polymer network formation

CO₂-induced plasticization may significantly spoil the membrane performance in high-pressure CO₂/CH₄ separations. The polymer matrix swells upon sorption of CO₂, which accelerates the permeation of CH₄. The polymer membrane looses its selectivity. To make membranes attractive for, for example, natural gas upgrading, plasticization should be minimized. In this article we study a polymer membrane stabilization by a semiinterpenetrating polymer network (s-ipn) formation. For this purpose, the polyimide Matrimid 5218 is blended with the oligomer Thermid FA-700 and subsequently heat treated at 265°C. Homogeneous films are prepared with different Matrimid/Thermid ratios and different curing times. The stability of the modified membrane is tested with permeation experiments with pure CO₂ as well as CO₂/CH₄ gas mixtures. The original membrane shows a minimum in its permeability vs. pressure curves, but the modified membranes do not indicating suppressed plasticization. Membrane performances for CO₂/CH₄ gas mixtures showed that the plasticizing effect indeed accelerates the permeation of methane. The modified membrane clearly shows suppression of the undesired methane acceleration. It was also found that just blending Matrimid and Thermid was not sufficient to suppress plasticization. The subsequent heat treatment that results in the s-ipn was necessary to obtain a stabilized permeability. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1547–1556, 1998     

Chromatographic investigation of the effect of dissolved carbon dioxide on the glass transition temperature of a polymer and the solubility of a third component (additive)

The effect of dissolved carbon dioxide on the glass transition temperature of a polymer, PMMA, has been investigated using molecular probe chromatography. The probe solute was iso-octane, and the specific retention volumes of this solute in pure PMMA and mixtures of PMMA with CO₂ were measured over a temperature range of 0 to 180°C and CO₂ pressures from 1 to 75 atm. The amount of CO₂ dissolved in the polymer was calculated from a model fit to previously published solubility data determined chromatographically. Classical van't Hoff-type plots were used to determine the glass transition temperature of CO₂-impregnated PMMA from low pressure up to 46 atm of CO₂. Solvent-induced plasticization was observed with the glass transition temperature decreasing by about 40°C. At some pressures, glass transitions at low temperatures could not be determined from the van't Hoff plots because of the proximity of the polymer glass transition temperature to the gas–liquid transition temperature for CO₂. For these pressures, a new method was developed to determine the glass transition composition. The glass transition pressure was then calculated from the measured composition and temperature using an isotherm model. In every case, the glass transition temperature decreased linearly with increasing concentration of CO₂ in the polymer. However, at higher compositions, the glass transition pressure decreased with increasing composition and decreasing temperature. The observed retention volume of iso-octane with PMMA in a glassy state was correlated with an adsorption model developed from a theory for liquid–solid chromatography derived by Martire. This model accurately described the observed decrease in retention of iso-octane by adsorption on the surface of glassy PMMA with increasing concentration of CO₂ dissolved in the polymer. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2537–2549, 1998     

Dispersion polymerization of methyl methacrylate in supercritical carbon dioxide: Influence of helium concentration on particle size and particle size distribution

Dispersion polymerizations of methyl methacrylate utilizing poly(1,1,-dihydroperfluorooctyl acrylate) as a steric stabilizer in supercritical carbon dioxide (CO₂) were carried out in the presence of helium. Particle size and particle size distribution were found to be dependent on the amount of inert helium present. Particle sizes ranging from 1.64 to 2.66 μm were obtained with various amounts of helium. Solvatochromic investigations using 9-(α-perfluoroheptyl-β,β-dicyanovinyl)julolidine indicated that the solvent strength of CO₂ decreases with increasing helium concentration. This effect was confirmed by calculations of Hildebrand solubility parameters. Dispersion polymerization results indicate that PMMA particle size can be attenuated by the amount of helium present in supercritical CO₂. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2009–2013, 1997     

Solid‐state microcellular and nanocellular polysulfone foams

In this article, we report on the process for creating microcellular and nanocellular polysulfone (PSU) foams. Microcellular foams with cell size up to 8 µm and nanocellular foams with cell size in the range of 20–30 nm were created. A range of CO₂ concentration was achieved by varying saturation temperature, from 5% at 60 °C to 14.7% at ?10 °C. The CO₂ concentration has a strong influence on the cellular structure. There exists a critical concentration window, between 10.7% and 12.3%, within which cell nucleation densities increase rapidly and cell sizes drop from micrometer range to below 1 µm into the nanometer range. Nanofoams with cell nucleation densities exceeding 10¹⁵ cells/cm³ and void fraction of up to 48% are achieved. At the high CO₂ concentration region, the change from closed nanocellular structure to bicontinuous nanoporous structure is observed. Also, nanostructures on the cell wall of microcells are observed and believed to be formed via stress‐induced nucleation/spinodal decomposition. The PSU nanofoams produced in this study present an opportunity to produce polymer nanofoams with a relatively high service temperature. The ability to create cells of different length scales provides an opportunity to study the effect of cell size on the foams properties. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 975–985     

CO2‐delayed crystallization of isotactic polypropylene: A kinetic study

The effect of CO₂ on the nonisothermal crystallization of isotactic polypropylene (iPP) was studied with high‐pressure differential scanning calorimetry at cooling rates of 0.2–5 °C/min. CO₂ significantly delayed the melt crystallization of iPP, and both the crystallization temperature and the heat of crystallization decreased with increasing CO₂ pressure. The crystallization rate of iPP, as characterized by the half‐time, was also prolonged by the presence of CO₂. With a modified Ozawa model developed by Seo, the Avrami crystallization exponent n of iPP was calculated. This value was depressed by the addition of CO₂ and was strongly dependent on the CO₂ pressure at low cooling rates. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1518–1525, 2003     

Preparation of CO_2 selective composite membranes using Pebax/CuBTC/PEG-ran-PPG ternary system

Three phase Pebax~? MH 1657/PEG-ran-PPG/CuBTC(polymer/liquid/solid) was successfully deposited as a selective layer on a porous Polysulfone(PSF) support. In fact, the beneficial properties of PEG(high selectivity) with those of PPG(high permeability, amorphous) have been combined with superior properties of mixed matrix membrane(MMMs). The membranes were characterized by DSC, TGA and SEM, while CuBTC was characterized by CO_2 and CH_4adsorption test. Statistically based experimental design(central composite design, CCD) was applied to analyze and optimize the effect of PEG-ran-PPG(10–50 wt%) and CuBTC(0–20 wt%) mass contents on the CO_2 permeance and CO_2/CH_4 ideal selectivity. Based on the regression coefficients of the obtained models, the CO_2 permeance was notably influenced by PEG-ran-PPG,while CuBTC has the most significant effect on the CO_2/CH_4 ideal selectivity. Under the optimum conditions(PEG-ran-PPG: 32.76 wt% and CuBTC: 20 wt%), nearly 620% increase in the CO_2 permeance and43% enhancement in the CO_2/CH_4 ideal selectivity was observed compared to the neat Pebax. The effect of pressure(3, 9 and 15 bar) on the pure and mixed gas separation performance of the composite membranes was also investigated. The high solubility of CO_2 in the membranes resulted in the enhancement of CO_2 permeability with increase in gas pressure.     

Syntheses and permselectivity properties of polysulfones based on bisphenol A and 1, 1 bi‐2 naphthol

Polysulfone copolymers based on mixtures of bisphenol A, BPA, and 1,1 bi‐2 naphthol, BN, diols have been synthesized and their gas permeability coefficients and selectivity separation factors for O₂/N₂ and CO₂/CH₄, at 5 atm and 35 °C, have been measured in a standard permeation cell. The polysulfone copolymers can form flexible thin films suitable for gas separation membranes. The gas selectivity for O₂/N₂ measured for the polysulfone copolymers synthesized with 50 and 70 mol % of BN, with the rest being BPA, in the initial mixture of diols are 6.4 and 6.8, respectively. The corresponding gas permeability coefficients for O₂ are 1.24 and 1.09 Barrers. Compared to the corresponding selectivity and permeability balance reported for polysulfones based on pure BPA, BPA–PSF, the copolymers show a balance that moves in the direction of higher selectivity with small losses in the permeability of the fastest gas. From the glass transition temperature determinations, it is observed that the incorporation of BN in the repeating unit of BPA–PSF inhibits large‐scale segmental motions that are reflected in reductions in the diffusivity coefficients for all gases. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 226–231, 2004     

Sorption of small molecules in various polycarbonates and Kapton-H

Pressure-composition isotherms were determined at 20°C for CO₂ in Kapton and various substituted polycarbonates and for H₂O, Ar, N₂, CH₄, and acetone in bisphenol-A-polycarbonate. The isotherms are described by two parameters an average free energy of sorption and a width of a Gaussian distribution of free sorption energies. Within the framework of a recent model these parameters can be calculated assuming an elastic distortion of the polymer caused by the incorporation of solute atoms in preexisting holes. By comparing experimental values with predictions of the model the experimental width of the free energy distribution is only 30% smaller than the theoretical one. Functional relationships are obeyed between the sorption parameters on the one hand and glass transition temperature, average hole volume, and molecular volume of the solute on the other hand. Deviations occur for larger molecules like acetone and ethylene which are attributed to a viscoelastic distortion of the polymer. Comparing free energies of solution for the rubbery and glassy state of the polymer reveals more negative values for the glassy polymers despite their extra elastic distortion energy. This discrepancy is overcome by taking into account that the occupied volume has to be re-formed in the case of the rubbery or liquid polymer. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 483–494, 1998     

Specific ionic conduction in poly[oligo (oxyethylene glycol) methacrylate] (PMEO)–Li salt complexes under high‐pressure CO2

We measured the ionic conductivity of amorphous poly[oligo (oxyethylene glycol) methacrylate] (PMEO)–lithium salt complexes under a CO₂ pressure varying from 0.1 to 20 MPa. The pressure dependence of the conductivity was positive, and the conductivity was higher than that under an inert gas such as N₂. The ion‐conductive behavior has been modeled using both the Vogel–Tammann–Fulcher (VTF) equation and activation volume theory. The calculated parameters of the VTF equation show that CO₂ that had permeated into the PMEO matrix acts as solvent molecules to dissolve ions and lower the glass transition temperature at high pressures. The ionic conduction in PMEO complexes under high‐pressure CO₂ was scarcely related to the VTF parameters and activation volume equations. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3151–3158, 2005     

Electron paramagnetic resonance spin probe study of carbon dioxide‐induced polymer plasticization

Steady‐state electron paramagnetic resonance (EPR) spectroscopy using nitroxide spin probes has been used to investigate the plasticization of poly(vinyl acetate) and poly(ethyl methacrylate) by carbon dioxide. By varying the CO₂ pressure at constant ambient temperature, the glass transition for each polymer could be depressed to 25 °C. This effect has been quantified by a parameter P_50G, obtained by plotting the EPR spectral width as a function of CO₂ pressure. Certain spin probes showed free volume distribution effects, manifested in the EPR spectra as “double peaks.” Possible reasons for this phenomenon are presented and discussed, and the efficacy of CO₂ as a plasticizer is clearly demonstrated by direct comparison with di‐n‐butyl phthalate. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2097–2108, 2005