Flow-assisted automated solid-phase microextraction for the determination of chloroethers in aqueous matrices

In this study a method of flow-assisted automated solid-phase microextraction (FA-SPME) was developed for the determination of organic pollutants in aqueous samples. A CTC Combi-PAL autosampler coupled with gas chromatography–mass spectrometry (GC–MS) was used to automate the entire extraction process. In this method, the SPME fibre was exposed to 100 mL of sample in a direct immersion mode for 10 min. After exposure, the fibre was desorbed at the injection port of GC–MS. To demonstrate the applicability of FA-SPME, chloroethers were selected as model compounds. Good linear correlation was found over a concentration range of 0.5–100 µg/L. The detection limits of the method were determined between 0.02 and 0.05 µg/L with the coefficients of determination (R²) from 0.9980 to 0.9996. The relative standard deviations (RSDs) of the FA-SPME for three sequential FA-SPME analyses were determined to be in the range between 1.2% and 6.2% (n = 3). The applicability of the method was assessed by means of recovery studies and satisfactory values for all compounds were obtained. This optimised method was used in the analysis of water and human urine samples to show the matrix effect on FA-SPME. This FA-SPME/GC–MS is substantially faster and suitable for the routine continuous flow-mode environmental monitoring applications.     

Headspace solid-phase microextraction with on-fiber derivatization for the determination of aldehydes in algae by gas chromatography-mass spectrometry

A simple, fast, sensitive and cost-effective method based on headspace solid-phase microextraction (HS-SPME) with on-fiber derivatization coupled with gas chromatography-mass spectrometry was developed for the determination of six typical aldehydes, 2E-hexenal, heptanal, 2E-heptenal, 2E,4E-heptadienal, 2E-decenal and 2E,4E-decadienal in laboratory algae cultures. As derivatization reagent, O-2,3,4,5,6-(pentafluorobenzyl) hydroxylamine hydrochloride, was loaded onto the poly(dimethylsiloxane)/divinylbenzene fiber for aldehydes on-fiber derivatization prior to HS-SPME. Various influence factors of extraction efficiency were systematically investigated. Under optimized extraction conditions, excellent method performances for all the six aldehydes were attained, such as satisfactory extraction recoveries ranging from 67.1 to 117%, with the precision (relative standard deviation) within 5.3-11.1%, and low detection limits in the range of 0.026-0.044 μg/L. The validated method was successfully applied for the analysis of the aldehydes in two diatoms (Skeletonema costatum and Chaetoceros muelleri), two pyrrophytas (Prorocentrum micans and Scrippsiella trochoidea) and Calanus sinicus eggs (feeding on the two diatoms above).     

Purge-assisted headspace solid-phase microextraction combined with gas chromatography-mass spectrometry for determination of chlorophenols in aqueous samples

A simple, economical and very effective method is demonstrated for simultaneous determination of 2,4-dichlorophenol, 2,4,6-trichlorophenol, 2,3,4,6-tetrachlorophenol and pentachlorophenol, in aqueous samples, by using purge-assisted headspace solid-phase microextraction (PA/HS-SPME) coupled to gas chromatography-mass spectrometry (GC-MS). In the new method, purging the sample enhances the removal of the trace chlorophenols without derivatization from the matrices to the headspace. Extraction parameters including extraction temperature, purge gas flow rate and extraction time were systematically investigated. Under optimal conditions, the relative standard deviations (RSDs) were 4-11% at 50 pg/mL and 5-14% at 5 pg/mL, respectively. The recoveries were in the range of 83-114%. Detection limits were determined at the fg level. These results indicate that PA/HS-SPME provides a significant contribution to highly efficient extraction of semi-volatile CPs, especially for pentachlorophenol, which has the smallest Henry's constant and large octanol-water partitioning coefficient. In addition, the proposed method was successfully applied to the analysis of chlorophenols in landfill leachate. New perspectives are opened for headspace extraction of relatively low vapor pressure compounds in complex matrices.     

Surfactant-sensitized malachite green method for trace determination of orthophosphate in aqueous solution

A surfactant-sensitized spectrophotometric method for determination of trace orthophosphate has been developed using anion surfactant (Ultrawet 60 L) with molybdate and malachite green in low acidic medium (pH_T 1.0). The method detection limit (3 × standard deviation of blank, n = 10) was 8 nM and the calibration curve was linear over a range of 10-400 nM (r² = 0.997). The molar absorptivity was 1.26 × 10⁵ L mol⁻¹ cm⁻¹ at 600 nm with the background correction at 530 nm. The precision of method was 3.4% at 50 nM and 2.4% at 100 nM orthophosphate (n = 10). The hydrolysis of eight organic phosphorus and polyphosphate compounds was less than 2% of the total phosphorus present (5-10 μM). This method showed less arsenate interference than previous methods, with only 3% even in the presence of orthophosphate in the samples. No interference of silicate up to 40 μM was observed. Background anions (in an order of SO₄²⁻ > NO₃⁻ > Cl⁻) have greater effects than cations (Ca²⁺ > Mg²⁺ > Na⁺) on the reagent blank and the molar absorptivity of the color product.     

Development of solid-phase extraction and solid-phase microextraction methods for the determination of chlorophenols in cork macerate and wine samples

Tri-, tetra- and pentachlorophenol (TCP, TeCP and PCP) can be considered the precursors in the formation of corresponding chloroanisoles, known to be powerful odorants in corks and wine. Determining the presence of these chlorophenolic compounds in cork soaking solutions (ethanol/water mixtures, 12% (v/v) ethanol used for cork quality control testing), or in wine can be achieved by acetylation/gas chromatography electron-capture detection. In order to reach the required sensitivity, a previous preconcentration step is necessary. Solid-phase extraction (SPE) and headspace solid-phase microextraction (HS-SPME) have given good results for the preconcentration of TCP, TeCP and PCP in such matrices. The use of Oasis HLB cartridges gives acceptable recoveries for the three compounds when different volumes (50-250 mL) of cork macerate with concentrations ranging from 20 to 150 ng/L are processed. Preconcentration based on HS-SPME has also been optimised with a 100 microm polydimethylsiloxane fibre and in situ derivatization. The HS-SPME method allows chlorophenols in a cork soaking solution and in wine to be determined with a limit of detection of 1 ng/L for each compound (in cork macerate) and a repeatability of around 0.5%-5% (n=8) for a concentration level of 30 ng/L.     

A critical review in calibration methods for solid-phase microextraction

Solid-phase microextraction (SPME) was developed to address the need for rapid sampling and sample preparation, both in the laboratory and on-site. Unlike traditional sample preparation methods, SPME is a non-exhaustive extraction technique in which only a small portion of the target analyte is removed from the sample matrix. Therefore, calibration of SPME for quantitative analysis is very important. In this review, we summarized the proposed SPME calibration methods and the characteristics of these methods were discussed.     

Analysis of aldehydes in water by solid-phase microextraction with on-fiber derivatization

The solid-phase microextraction (SPME) technique with on-fiber derivatization was evaluated for the analysis of aldehydes in water. The poly(dimethylsiloxane)/divinylbenzene (PDMS/DVB) fiber was used and O-2,3,4,5,6-(pentafluorobenzyl)hydroxylamine hydrochloride (PFBHA) were first loaded onto the fiber. The aldehydes in water sample were agitated into headspace and extracted by SPME with on-fiber derivatization. Gas chromatography/mass spectrometry (GC/MS) was used for the analysis of oximes formed and the adsorption-time profiles were examined. The precision, recovery and method detection limits (MDLs) were evaluated with spiked bidistilled water, chlorinated tap water as well as well water. The relative standard deviations from different spiked water sample were all less than 10% and the recoveries were 100 +/- 15%. With 2 ml of water sample, MDLs were in the range of 0.12-0.34 microg/l. Compared with other techniques, the study shown here provided a simple, fast and reliable method for the analysis of aldehydes in water.     

Simple and automatic determination of aldehydes and acetone in water by headspace solid-phase microextraction and gas chromatography-mass spectrometry

We describe a simple and automatic method to determine nine aldehydes and acetone simultaneously in water. This method is based on derivatization with 2,2,2-trifluoroethylhydrazine (TFEH) and consecutive headspace-solid-phase microextraction and gas chromatography-mass spectrometry. Acetone-d(6) was used as the internal standard. Aldehydes and acetone in water reacted for 30 min at 40°C with TFEH in a headspace vial and the formed TFEH derivatives were simultaneously vaporized and adsorbed on polydimethylsiloxane-divinylbenzene. Under the established condition, the method detection limit was 0.1-0.5 μg/L in 4 mL water and the relative standard deviation was less than 13% at concentrations of 0.25 and 0.05 mg/L. This method was applied to determine aldehydes and acetone in 5 mineral water and 114 surface water samples. All mineral water samples had detectable levels of methanal (24.0-61.8 μg/L), ethanal (57.7-110.9 μg/L), propanal (11.5-11.7 μg/L), butanal, pentanal (3.3-3.4 μg/L) and nonanal (0.3-0.4 μg/L). Methanal and ethanal were also detected in concentration range of 2.7-117.2 and 1.2-11.9 μg/L, respectively, in surface water of 114 monitoring sites in Korea.     

Microwave-assisted headspace solid-phase microextraction for the rapid determination of organophosphate esters in aqueous samples by gas chromatography-mass spectrometry

The rapid and solvent-free determination of organophosphate esters (OPEs) in aqueous samples via one-step microwave-assisted headspace solid-phase microextraction (MA-HS-SPME) followed by gas chromatography-mass spectrometry (GC-MS) analysis is described. Tri-n-butyl phosphate (TnBP) and tris-(2-ethylhexyl) phosphate (TEHP) were selected as model compounds for the method of development and validation. The effects of various extraction parameters for the quantitative extraction of these analytes by MA-HS-SPME were systematically investigated and optimized. The analytes, in a 20 mL water sample (in a 40 mL sample bottle containing 2 g of NaCl, pH 3.0), were efficiently extracted by a polydimethylsiloxane-divinylbenzene (PDMS-DVB) fiber placed in the headspace when the system was microwave irradiated at 140 W for 5 min. The limits of quantification (LOQs) for TnBP and TEHP were 0.5 and 4 ng/L, respectively. Using the standard addition method, MA-HS-SPME coupled with GC-MS was utilized to determine selected OPEs in surface water and wastewater treatment plants (WWTP) influent/effluent samples. Preliminary results show that TnBP was commonly detected OPEs in these aqueous samples, the correlation coefficients (r²) of the standard addition curves were greater than 0.9822, indicating that the developed method appears to be a good alternative technique for analyzing OPEs in aqueous samples.     

Determination of aldehydes in drinking water using pentafluorobenzylhydroxylamine derivatization and solid-phase microextraction

A headspace solid-phase microextraction (HS-SPME) procedure followed by gas chromatography and electron capture detection (GC-ECD) has been developed for the determination of aldehydes in drinking water samples at microg/l concentrations. A previous derivatization with o-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine hydrochloride (PFBHA) was performed due to the high polarity and instability of these ozonation by-products. Several SPME coatings were tested and the divinylbenzene-polydimethylsiloxane (DVB-PDMS) coating in being the most suitable for the determination of these analytes. Experimental SPME parameters such as selection of coating, sample volume, addition of salt, extraction time and temperature of desorption were studied. Analytical parameters such as precision, linearity and detection limits were also determined. HS-SPME was compared to liquid-liquid microextraction (proposed in US Environmental Protection Agency Method 556) by analyzing spiked water samples; a good agreement between results obtained with both techniques was observed. Finally, aldehydes formed at the Barcelona water treatment plant (N.E. Spain) were determined at levels of 0.1-0.5 microg/l. As a conclusion, HS-SPME is a powerful tool for determining ozonation by-products in treated water.     

Recent development in liquid phase microextraction for determination of trace level concentration of metals—A review

As the drive towards green extraction methods has gained momentum in recent years, it has not always been possible to eliminate organic solvents completely. However, the volumes employed have been reduced remarkably, so that a single microdrop is sufficient in some cases. This effort has led to the development of various liquid phase microextractions namely single drop microextraction (SDME), hollow fiber liquid phase microextraction (HF-LPME), dispersive liquid-liquid microextraction (DLLME) and solidified floating organic drop microextraction (SFODME). In this review, the historical development and overview of these miniaturized liquid phase extraction methodologies have briefly been discussed and a comprehensive collection of application of the these methods in combination with different analytical techniques for preconcentration and determination of ultra trace amounts of metals and organometal ions in various matrices have been summarized.     

Ordered mesoporous carbon film as an effective solid-phase microextraction coating for determination of benzene series from aqueous media

The present work reports preparation of ordered mesoporous carbon (OMC) film supported on a graphite fiber as a new type of solid-phase microextraction (SPME) fiber for determination of benzene series from aqueous media. The strategy for the supported OMC film preparation was combined dip-coating technology with solvent evaporation-induced self-assembly (EISA) approach. A graphite fiber was immersed in an ethanol solution containing phenolic resin and Pluronic triblock copolymer. Upon solvent evaporation and subsequent pyrolysis under 700 °C, the phenolic resin and the surfactant self-assembled on the surface of the graphite fiber to form smooth OMC film. X-ray diffraction (XRD), transmission electron microscopy (TEM) and nitrogen isothermal adsorption results indicate that the resultant OMC film possesses well-ordered two dimensional hexagonal mesostructure with pore diameters of 4.5 nm and BET surfaces of 630 m²/g. Scanning electron microscopy (SEM) studies show the supported OMC film with thickness at 8.5 μm is continuous and defect-free. The SPME efficiency of the OMC fiber was evaluated by analysis of five benzene series (benzene, toluene, ethylbenzene, p-xylene and m-xylene) from water samples by gas chromatography-flame ionization detection (GC-FID). The analysis results indicate that the prepared OMC fiber has wide linear ranges (0.5–500 μg/L), low detection limits (0.01–0.05 μg/L) and good repeatabilities (4.0–5.8% for one fiber, 2.9–8.7% for fiber-to-fiber). Compared with commercial counterparts, the OMC fiber exhibits improved extraction efficiency for benzene series and PAHs.     

Evaluation of capillary gas chromatography columns for the determination of free volatile amines after solid-phase microextraction

Summary Gas-liquid chromatographic capillary columns coated with 14% diphenyldimethylpolysiloxane, base-deactivated 5% diphenyldimethylpolysiloxane, or poly(ethylene glycol), and deactivated porous polymer for capillary gas-solid chromatography were evaluated for analysis of low-molecular-weight (C₁−C₉) amines. Solid-phase microextraction with a polydimethylsiloxane fiber was used for headspace sampling and for introduction of the sample into the gas chromatograph. As expected, basic of aliphatic gaseous or volatile aliphatic amines (carbon number: C₁−C₄). A thick (e. g. 3 μm) film of 5% diphenyldimethylpolysiloxane enabled determination of analytes in a wider molecular-weight range (C₃−C₉) with acceptable efficiency and resolution.     

Application of solid-phase microextraction for determination of organic vapours in gaseous matrices

This paper reviews the practical applications of solid-phase microextraction (SPME) in the analysis of organic vapours which are pollutants of atmospheric air, indoor air and workplace air. Applications to headspace of solids and liquids such as different waters, soils, food, etc., are also included. Problems related to calibration in SPME analysis of gaseous matrices are also dealt with. Calibration procedures and apparatus for generation of standard gaseous mixtures are described. Advantages and limitations of SPME based gas chromatographic methods of air organic pollutants are discussed.     

A novel solid-phase microextraction method based on polymer monolith frit combining with high-performance liquid chromatography for determination of aldehydes in biological samples

In this work, a polypropylene frit with porous network structure (20 μm pole size) was first utilized as the mould of polymer monolithic material, poly(methacrylic acid-co-ethylene glycol dimethacrylate) (MAA-co-EDMA) monolith was synthesized within channels and macropores of the frit. A simple and sensitive solid-phase microextraction method based on polymer monolith frit coupled with high-performance liquid chromatography (HPLC) was established and applied to analysis of hexanal and heptanal in biological samples (human urine and serum). In the method, small molecule metabolites (aldehydes) in biological samples derivatized with 2,4-dinitrophenylhydrazine (DNPH), and the formed hydrazones were extracted simultaneously on the monolithic frit and thereafter ultrasound-assisted desorbed with acetonitrile as elution solvent. The experimental parameters with regard to polymerization, derivatization and extraction were investigated. Under the optimal conditions, the linearity was in the range of 0.02–5.0 μmol L⁻¹ (r = 0.9994) for both hexanal and heptanal and the limits of detection (S/N = 3) were 0.81 nmol L⁻¹ for hexanal and 0.76 nmol L⁻¹ for heptanal. The relative standard deviations (RSDs, n = 5) were less than 6.5% for the same monolithic frit and less than 8.9% for the different monolithic frits. Satisfactory recoveries ranging from 70.71% to 88.73% were obtained for the urine samples. The method possesses many advantages including simple setup, fast analysis, low cost, sufficient sensitivity, good biological compatibility and less organic solvent consumption. The proposed method is a useful assistant tool in the clinical early diagnosis of lung disease by monitoring aldehyde biomarker candidates in complex biological samples.     

Evaluation of solid-phase microextraction conditions for the determination of polycyclic aromatic hydrocarbons in aquatic species using gas chromatography

This paper describes a headspace solid-phase microextraction (HS-SPME) procedure coupled to gas chromatography with mass spectrometric detection (GC–MS) for the determination of eight PAHs in aquatic species. The influence of various parameters on the PAH extraction efficiency was carefully examined. At 75 °C and for an extraction time of 60 min, a polydimethylsiloxane–divinylbenzene (PDMS/DVB) fiber coating was found to be most suitable. Under the optimized conditions, detection limits ranged from 8 to 450 pg g⁻¹, depending on the compound and the sample matrix. The repeatability varied between 7 and 15% (RSD). Accuracy was tested using the NIST SRM 1974b reference material. The method was successfully applied to different samples, and the studied PAHs were detected in several of the samples. Figure Headspace SPME sampling followed by GC–MS facilitates routine monitoring of PAHs in aquatic species     

Semiquantitative determination of off-notes in mint oils by solid-phase microextraction

Mint essential oils are produced by the steam distillation of dried or partially dried harvested plant material. In the United States, harvesting is done mechanically so that any weeds found in the field are concomitantly harvested. Steam distillation of contaminated plant material leads to off-notes in the oil, which are currently determined by a sensory panel. Furthermore, nonoptimized distillation conditions can lead to the thermal degradation of carbohydrates and proteins resulting also in the formation of very volatile off top-notes. As a result, the use of a nonequilibrated solid-phase microextraction (SPME) procedure to determine the off-notes is evaluated. The results of this evaluation include a combination of semiquantitative data, odor threshold data, and mathematical data manipulation to ascertain the capabilities of a SPME approach. The results are correlated with sensory panel data to yield a relatively rapid analytical methodology that can be used either in place of or in support of sensory analyses. The main advantage of the technique described is to provide some semiquantitative data in support of the odor-panel screening of mint oils for off-notes. Based on the data presented in this report, it is believed that this has been successfully demonstrated.     

Rapid determination of organotin compounds by headspace solid-phase microextraction

Headspace solid-phase microextraction (SPME) followed by gas chromatography (GC) coupled to pulsed flame photometric detection have been investigated for the simultaneous speciation analysis of 14 organotin compounds, including methyl-, butyl-, phenyl-, and octyltins compounds. The analytical process (sorption on SPME fibre and thermal desorption in GC injection port) has been optimised using experimental designs. Six operating factors were considered in order to evaluate their influence on the performances of a SPME-based procedure. The evaluation of accuracy, precision and limits of detection (LODs) according to ISO standards and IUPAC recommendations has allowed the method to be validated. The LODs obtained for the 14 studied organotins compounds are widely sub-ng(Sn) l(-1). The precision evaluated using relative standard deviation ranges between 9 and 25% from five determinations of the analytes at 0.25-125 ng(Sn) l(-1) concentrations. The accuracy was studied throughout the analysis of spiked environmental samples. These first results show that headspace SPME appears really as attractive for organotins determination in the environment and the monitoring of their biogeochemical cycle.     

自动顶空衍生化固相微萃取法测定啤酒中的老化醛类化合物

采用邻-五氟苯甲基羟胺(PFBOA)衍生,顶空固相微萃取(HS-SPME)和气相色谱质谱(GC-MS)测定啤酒中2-甲基丁醛、3-甲基丁醛、反-2-壬烯醛等8种老化醛类化合物.顶空固相微萃取采用65 μm PDMS/DVB纤维,先用纤维吸附PFBOA溶液,再将纤维插入装有2 mL啤酒的20 mL顶空进样瓶的顶空中在60 ℃萃取60 min,衍生和萃取都在自动进样器中进行.采用GC-MS检测,特征离子为m/z 181.8种羰基化合物在0.2～500 μg/L范围内线性关系良好,相关系数在0.990以上.检测样品的相对标准偏差为1.0%～15.7%,回收率为88%～103%.同时研究并讨论了萃取纤维、萃取温度、萃取时间、样品体积等因素对醛类萃取量的影响.该方法可用于啤酒保鲜期研究和产品质量控制.