Investigation of Relaxation Process of Nylon 1212 Using Dielectric Relaxation Spectroscopy

The relaxation processes of α-form nylon 1212 from 50°C up to 160°C were studied by dielectric relaxation spectroscopy (DRS) in a wide frequency range of 63 Hz to 5 MHz. The α relaxation, the electrode relaxation, and the conductivity relaxation of nylon 1212 were observed and analyzed in detail using permittivity and modulus formalism. Electrode polarization and dc conductivity were the origin of high dielectric permittivity values at low frequencies and high temperatures. The strength of the imaginary part of the electric modulus of conductivity relaxation M″ _max was nearly independent of temperature. The distribution of local conductivity and relaxation time became broader with decreasing temperature.     

Effect of carbon nanotubes implantation on electrical properties of sisal fibre–epoxy composites

In this paper, the effects of carbon nanotubes (CNT) implantation and sisal fibre size on the electrical properties of sisal fibre-reinforced epoxy composites are reported. For this purpose, the epoxy composites reinforced with CNT-implanted sisal fibre of 5 mm and 10 mm lengths were prepared by hand moulding and samples characterized for their electrical properties, such as dielectric constant (ε′), dielectric dissipation factor (tan δ) and AC conductivity (σ_ac) at different temperatures and frequencies. It was observed that the dielectric constant increases with increase in temperature and decreases with increase in frequency from 500 Hz to 5 KHz. Interestingly, the sample having CNT-implanted sisal fibre of 5 mm length exhibited the highest value of dielectric constant than the one with length 10 mm. This is attributed to the increased surface area of sisal fibre and enhancement of the interfacial polarization. At a constant volume and a length of 5 mm of the fibres, the number of interfaces per unit volume element is high and results in a higher interfacial polarization. The interfaces decrease as the fibre length increases, and therefore, the value of ε′ decreases at 10 mm fibre length. The peak value of the dielectric constant decreases with increasing frequency. A continuous decrease in dissipation factor (tan δ) with increasing frequency for all samples was observed, while at lower temperatures, the values of tan δ remains approximately same. The AC conductivity for 5 mm length sisal epoxy composite and 10 mm length sisal fibre–epoxy composites is higher than that of pure epoxy at all the frequencies.     

Effects of oxygen partial pressure on the ferroelectric properties of pulsed laser deposited Ba0.8Sr0.2TiO3 thin films

The Ba_0.8Sr_0.2TiO₃ thin films were grown on the Pt–Si substrate at 700 °C by using a pulsed laser deposition technique at different oxygen partial pressure (PO₂) in the range of 1–20 Pa and their properties were investigated. It is observed that the PO₂ during the deposition plays an important role on the tetragonal distortion ratio, surface morphology, dielectric permittivity, ferroelectric polarization, switching response, and leakage currents of the films. With an increase in PO₂, the in-plane strain for the BST films changes from tensile to compressive. The films grown at 7.5 Pa show the optimum dielectric and ferroelectric properties and also exhibit the good polarization stability. It is assumed that a reasonable compressive strain, increasing the ionic displacement, and thus promotes the in-plane polarization in the field direction, could improve the dielectric permittivity. The butterfly features of the capacitance–voltage (C–V) characteristics and the bell shape curve in polarization current were attributed to the domain reversal process. The effect of pulse amplitude on the polarization reversal behavior of the BST films grown at PO₂ of 7.5 Pa was studied. The peak value of the polarization current shows exponential dependence on the electric field.     

Dielectric absorption in mixtures of anisole with some primary alcohols at microwave frequency

Dielectric properties of binary mixtures of anisole with methanol (MeOH), 1-propanol (1-PrOH), 1-butanol (1-BuOH) and 1-heptanol (1-HeOH) over an entire concentration range have been studied at a fixed temperature 40°C. The dielectric constant (ε′) and dielectric loss (ε″) of the binary mixtures of polar liquids have been determined at a microwave frequency of 9.1?GHz. The static dielectric permittivity (ε ₀) of the liquid samples was also determined using a precision LCR meter. Determined values of static dielectric permittivity (ε ₀) and dielectric permittivity (ε*) at 9.1?GHz frequency were used to evaluate relaxation time (τ) and high frequency limit dielectric permittivity (ε _∞). Dielectric parameters were interpreted in terms of molecular interaction between the anisole and alcohol molecules.     

A pure dielectric metamaterial absorber with broadband and thin thickness based on a cross-hole array structure

A pure dielectric metamaterial absorber with broadband and thin thickness is proposed, whose structure is designed as a periodic cross-hole array. The pure dielectric metamaterial absorber with high permittivity is prepared by ceramic reinforced polymer composites. Compared with those with low permittivity, the absorber with high permittivity is more sensitive to structural parameters, which means that it is easier to optimize the equivalent electromagnetic parameters and achieve wide impedance matching by altering the size or shape of the unit cell. The optimized metamaterial absorber exhibits reflection loss below -10 dB in 7.93 GHz-35.76 GHz with a thickness of 3.5 mm, which shows favorable absorption properties under the oblique incidence of TE polarization (±45°). Whether it is a measured or simulated value, the strongest absorbing peak reaches below -45 dB, which exceeds that of most metamaterial absorbers. The distributions of power loss density and electric and magnetic fields are investigated to study the origin of their strong absorbing properties. Multiple resonance mechanisms are proposed to explain the phenomenon, including polarization relaxation of the dielectric and edge effects of the cross-hole array. This work overcomes the shortcomings of the narrow absorbing bandwidth of dielectrics. It demonstrates that the pure dielectric metamaterial absorber with high permittivity has great potential in the field of microwave absorption.     

Temperature and induced electric field dependence on the phase transition of 9/70/30, 9/65/35 and 9/60/40 PLZT ceramics

In this work, Pb_0.91La_0.09(Zr_1–xTi_x)_0.9775O₃ ceramics where x = 0.3, 0.35 and 0.4 (the composition near MPB) were prepared by solid solution method. After fabrication process, electrical property was measured by LCR meter. Polarization and induced strain behavior of the samples were investigated by using interferometry technique modified with Sawyer–Tower circuit at various temperatures. The results of dielectric, polarization and induced strain properties were due to the Zr/Ti ratios, which changed their behavior when temperature was varied (30–70 °C). The normal to macro-micro domains to relaxor and paraelectric phase transition was demonstrated which is related to linear or nonlinear increase of polarization and induced strain as a function of applied subswitching electric field.     

Enhancement of dielectric and ferroelectric properties in ferroelectric superlattices

I studied theoretically the enhancement of remanent polarization and dielectric permittivity of interfacial-coupled ferroelectric superlattices based on the Landau–Ginzburg theory. Our model adopts the Landau–Khalatnikov equation to describe hysteresis behavior and takes the time-dependent space-charge-limited conductivity into account to investigate the ferroelectric and dielectric properties of ferroelectric superlattices. The results are in good agreement with recent experimental observations on the enhancement of remanent polarization and permittivity of BaTiO₃/SrTiO₃ superlattices and heterolayered Pb(Zr,Ti)O₃ thin films.     

On the effect of SHI irradiation on dielectric properties of Y3+xFe5−xO12 (x=0.0–0.6) system

The present work aims to investigate the pre- and post-effect of 50 MeV Li³⁺ ion irradiation at a fluence of 5×10¹³ ions/cm² on the dielectric properties of Y_3+xFe_5?xO₁₂, x=0.0, 0.2, 0.4 and 0.6, garnet system over broad temperature, 300–673 K, and frequency, 100 Hz–13 MHz, ranges. Thermal variation of ac resistivity measurements suggests that the mechanism responsible for conduction in the system is polaron hopping. The observed modifications in dielectric properties after swift heavy ion irradiation are mainly due to the modifications of the metal–insulator contacts due to radiation damage-induced disorder and irradiation-induced point/cluster of defects in the material and also compressive strain generated in the lattice structure. The electric modulus presentation and the complex impedance spectral analysis have been employed to study the relaxation process. The YFeO₃ phase is found to be irradiation hard phase as compared with the garnet phase.     

Influence of Nd:YAG laser irradiation on AC impedance and dielectric properties of lithium ferrite

Polycrystalline samples of Li_0.5Fe_2.5O₄ spinel ferrite have been synthesized by a standard ceramic technique. The samples were irradiated with an Nd:YAG laser to study the effect of laser irradiation on the structural, dielectric and AC impedance properties. The X-ray diffraction results show the formation of a disordered cubic structure after irradiation. The dielectric constant (?′), dielectric loss (?″) and the loss tangent (tan δ ) were measured at room temperature as a function of frequency (f=20 Hz–1 MHz) for the irradiated and unirradiated samples of Li_0.5Fe_2.5O₄ spinel ferrite. The dielectric constant of the irradiated samples is decreased in magnitude compared to the unirradiated samples. It was found that laser irradiation increases the polarization and the resistivity of the samples as a result of electronic rearrangement and lattice defects. The AC conductivity of the samples was derived from the dielectric constant and loss tangent data. The change in AC conductivity is attributed to the creation of lattice vacancies after laser irradiation. The AC impedance analysis was used to separate the grain and grain boundary of the Li_0.5Fe_2.5O₄ spinel ferrite.     

Dielectric,thermal and Raman spectroscopy studies of lead-free (Na0.5Bi0.5)1−xSrxTiO3 (x = 0, 0.04 and 0.06) ceramics

ABSTRACT

Lead-free (Na_0.5Bi_0.5)_1?xSr_xTiO₃ (x = 0, 0.04 and 0.06) ceramics with relative densities above 97% were prepared by solid-state synthesis process. Their dielectric, thermal and Raman properties were studied. X-ray diffraction analysis shows perovskite structure with rhombohedral symmetry at room temperature. Sr doping of Na_0.5Bi_0.5TiO₃ (NBT) results in an increase of the dielectric permittivity, diffusing of the permittivity maximum and its shift toward lower temperatures. The temperature of the rhombohedral–tetragonal phase transition indicated by the differential scanning calorimetry (DSC) peak and relaxational dielectric anomaly near the depolarization temperature are also shifted toward lower temperatures. The observed increase and broadening of the permittivity maximum, enhancement of the dielectric relaxation near the depolarization temperature, broadening of the DSC anomaly related to the rhombohedral–tetragonal phase transition and broadening of the Raman bands with increasing Sr content are attributed to the increase of the degree of cationic disorder and evident enhancement of the relaxor-like features in NBT–xST. This enhancement could play a positive role in the improvement of the piezoelectric performance of NBT-based ceramics.     

Dielectric Dispersion Study of Poly(vinyl Pyrrolidone)–Polar Solvent Solutions in the Frequency Range 20 Hz–1 MHz

Influence of polar solvents environment and polymer concentrations on the electrical properties (complex dielectric constant, ac electrical conductivity, complex electric modulus and complex impedance) of the solutions of poly(vinyl pyrrolidone) (PVP) in polar solvents, namely water, ethyl alcohol, ethylene glycol, diethylene glycol, poly(ethylene glycol), glycerol, dimethyl sulfoxide and dimethyl formamide, have been investigated in the frequency range 20 Hz–1 MHz at 25°C. Comparative analysis of the dielectric dispersion curves confirms that the solvent molecular size and number of its hydroxyl groups, and the solutions viscosity, are the major factors which governs the PVP chain segmental motion. The ionic conduction and electrode polarization phenomena has a dominant influence on the large increase of complex dielectric constant values of the solutions of PVP‐polar solvent in the lower frequency region. The values of relaxation times corresponding to these phenomena are also reported.     

Mechanism of the polarization response in the relaxor state of lead scandotantalate single crystals with different levels of ion ordering

The dielectric properties and optical transmission of stoichiometric lead scandotantalate (PST) single crystals in strong electric fields was studied above the temperature of the spontaneous ferroelectric phase transition (T_sp). It is shown that the mechanism of polarization response directly above T_sp is related to induced polarization effects and macrohysteretic behavior only in ac fields above 5 kV/cm. Ananalysis of reciprocal dielectric permittivity carried out over a broad temperature range far above the temperature at which the dielectric permittivity passes through a maximum revealed that specific features of the relaxor behavior manifest themselves up to 400°C even in highly ordered PST crystals.     

Effective permittivity of periodic composite materials: Numerical modeling by the finite element method

The effective properties of composite materials are closely related to the composition and arrangement of its constituents. Many studies and articles are actively studying the dielectric properties of heterogeneous structures with random and periodic arrangement. In the quasistatic limit, we use the finite element method as a numerical tool to evaluate the effective permittivity of two and three component composites. Two heterostructures are investigated; the first is formed by crossed dielectric cylinders in permanent contact and arranged in three layers. The cylinders are immersed in a dielectric host medium. The second structure is similar to the first except that the tubes are covered by an interphase layer. The numerical tool used to extract the exact value of the effective permittivity takes into account all internal multipolar interactions which contribute to the polarization of the material medium. The impacts of the relative permittivity and volume fraction of cylinders, the thickness of interphase and its dielectric constant are reported. The Maxwell–Garnett theory fails to predict the effective permittivity of the studied structures for high volume fraction and permittivity contrast. To overcome this problem, an amendment was made to the McLachlan equation McQ also termed the Two Exponent Single Percolation Equation TESPE. The first exponent t is held equal to 1 and the other exponent s is depending on the volume fraction. s is calculated so that the whole values of the effective permittivity obtained by the McQ rule are exactly the same values obtained by the simulations. Finally, we obtained a chart and a model to find the values of s, a fast way that is very useful for practitioners and design engineers of composite materials.     

Raman spectra and anomalies of dielectric properties and thermal expansion of lead-free (1−x)Na0.5Bi0.5TiO3-xSrTiO3 (x = 0, 0.08 and 0.1) ceramics

ABSTRACT

Thermal expansion, Raman and dielectric properties of the lead-free (1?x)Na_0.5Bi_0.5TiO₃-xSrTiO₃ (x = 0, 0.08 and 0.1) ceramic solid solutions, fabricated by the conventional solid-state reaction method, were investigated. The Sr-doping results in an increase of the dielectric permittivity, broadening of the permittivity maximum, enhancement of the relaxation near depolarization temperature, broadening of the Raman bands and shift of all anomalies toward lower temperatures. The observed effects are attributed to an increase of the degree of cationic disorder and enhancement of the relaxor-like features. Anomalies in the thermal expansion strain were observed at the temperatures corresponding to the dielectric anomalies but not related to any phase transitions. These anomalies are supposed to follow changes of the averaged unit cell volume in the temperature interval of tetragonal and rhombohedral phase coexistence.     

Pretransitional dielectric properties of nematogenic 4-cyanophenyl-4′-n-heptylbenzoate

This article presents results of the static and dynamic dielectric studies performed for mesogenic 4-cyanophenyl-4′-n-heptylbenzoate in the isotropic (I) and nematic (N) phases. Pretransitional phenomena are observed in the vicinity of I–N phase transition as an anomalous temperature behavior of both the static and the dynamic dielectric properties of the compound. The temperature dependence of the static permittivity is correlated with the entropy change induced by the probing electric field while an anomalous behavior of the dielectric relaxation directly points out for a subdiffusional Brownian rotation of mesogenic molecules in the vicinity of the phase transition.     

Preparation of TiO2–MWCNT core/shell heterostructures containing a single MWCNT and their electromagnetic properties

TiO₂–MWCNT core/shell heterostructures containing a single MWCNT have been successfully prepared via solvothermal method. TiO₂–MWCNT heterostructures with different morphologies and electromagnetic (EM) properties have obtained by adjusting the weight ratio of titanium dioxide (TiO₂₎ and multi-walled carbon nanotubes (MWCNT) (weight ratio: 1:1, 5:1 and 10:1). EDS spectrum and X-ray diffraction analysis reveal that the product is composed of Ti, O, and C elements, and the crystal structure of TiO₂ is tetragonal anatase phase. SEM and TEM images show that the MWCNTs are coated by a thin layer of TiO₂ crystals, and the average diameters of the needle-like TiO₂ nanocrystals are less than 100 nm. EM properties of the as-prepared TiO₂–MWCNT heterostructures are investigated in the 0.5–18.0 GHz range. The permittivity and permeability of the TiO₂–MWCNT heterostructures change obviously as the weight ratio of TiO₂ and MWCNT increases. Moreover, the typical resonance–antiresonance phenomenon can be observed in the permittivity and permeability curves.     

Carbon materials with quasi-graphene layers: the dielectric, percolation properties and the electronic transport mechanism

We investigate the dielectric properties of multi-walled carbon nanotubes (MWCNTs) and graphite filling in SiO₂ with the filling concentration of 2-20 wt.% in the frequency range of 10²-10⁷ Hz. MWCNTs and graphite have general electrical properties and percolation phenomena owing to their quasi-structure made up of graphene layers. Both permittivity ε and conductivity σ exhibit jumps around the percolation threshold. Variations of dielectric properties of the composites are in agreement with the percolation theory. All the percolation phenomena are determined by hopping and migrating electrons, which are attributed to the special electronic transport mechanism of the fillers in the composites. However, the twin-percolation phenomenon exists when the concentration of MWCNTs is between 5-10 wt.% and 15-20 wt.% in the MWCNTs/SiO₂ composites, while in the graphite/SiO₂ composites, there is only one percolation phenomenon in the graphite concentration of 10-15 wt.%. The unique twin-percolation phenomenon of MWCNTs/SiO₂ is described and attributed to the electronic transfer mechanism, especially the network effect of MWCNTs in the composites. The formation of network plays an essential role in determining the second percolation threshold of MWCNTs/SiO₂.     

Enhanced dielectric permittivity of fluorine polyimide matrix with embedded graphene

A polymer nanohybrid material with enhanced dielectric permittivity was prepared using the fluorine‐containing polyimide (PI) 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride/4,4′‐oxydianiline (6FDA/ODA) as matrix and graphene as conductive filler in our present work. Studies on the dielectric properties of the 6FDA/ODA–graphene nanohybrid films show that the dielectric permittivity (ε) can be significantly enhanced by the layer‐by‐layer structure of graphene and the presence of fluorine also has an important influence on the improvement of ε. The percolation theory and microcapacitor model are used to explain the change of dielectric properties and a percolation threshold f_c = 0.0152 (2.45 wt%) was obtained by a linear‐fit calculation.

     

Contemplations on the impressions of MeV swift heavy ion irradiation on nonlinear optical dimethyl-amino-pyridinium-4-nitrophenolate-4-nitro-phenol (DMAPNP) single crystals

Organic nonlinear optical crystal dimethyl-amino-pyridinium-4-nitrophenolate-4-nitro-phenol was subjected to 100 MeV Ag⁸⁺ ions and 50 MeV Si⁸⁺ ions. The radiation effects are studied in terms of processes observed with the pristine samples and in comparison with them. The dielectric properties of the crystals were studied before and after irradiation from 100 Hz to 5 MHz at various temperatures (308–383 K). A drastic increase in the dielectric constant is seen due to irradiation. The dielectric constant and conductivity increases with the increase of irradiation fluence for the samples. The observed results are discussed in detail.     

Dielectric properties of Bi4Ti3O12–SrBi4Ti4O15 intergrowth ceramics synthesized by a modified oxalate route

In this study, Bi₄Ti₃O₁₂–SrBi₄Ti₄O₁₅ (BIT–SBTi) intergrowth ferroelectric ceramics was synthesized by a modified oxalate route. The phase formation behaviour, structure, morphology and electrical properties of the intergrowth ceramics were also investigated. The phase formation takes place through intermediate phases like SrBi₂O₄ and Bi₁₂TiO₂₀. The precursor mostly changes to Bi₄Ti₃O₁₂ at 600°C and to BIT–SBTi intergrowth at 800°C. Rietveld analysis of the X-ray diffraction pattern showed that the structure of the intergrowth compound was orthorhombic with lattice parameters a = 5.4408(3), b = 5.4505(1) and c = 74.0851(4) Å. The intergrowth ferroelectrics showed a phase transition at 610°C and a frequency-stable permittivity and dielectric loss behaviour. The intergrowth ferroelectrics also showed a larger 2P_r than their constituents BIT and SBTi.