基于空气孔微结构光纤的表面等离子体共振折射率传感器北大核心CSCD

提出了一种基于表面等离子体共振(SPR)效应增强的光子晶体光纤折射率传感器。该传感器结构通过光纤熔接机拼接光子晶体光纤(PCF),在光子晶体光纤中间引入一个空气孔形成PCF-空气孔-PCF的光纤传感结构,随后使用磁控溅射镀膜工艺在其表面沉积一层薄金膜制备而成。实验探究了折射率及温度对传感器的响应。结果表明,在1.333~1.389的折射率范围内,所提出的传感器的平均折射率灵敏度为2 142.52 nm,且测量线性度为0.981,品质因子约13.10。实验结果表明该传感器对温度不敏感。相比于无空气孔的PCF传感结构,引入的空气孔增强了SPR效应,使得传感器拥有良好的共振峰深度。得益于上述优势,该类型传感器有望在生物医学、环境监测等领域得到应用。     

High sensitivity dual core photonic crystal fiber sensor for simultaneous detection of two samples

The optical control ability of photonic crystal fiber (PCF) is a distinctive property suitable for improving sensing and plasma performance. This article proposes a dual-core D-channel PCF sensor that can detect two samples simultaneously, which effectively solves the problems of coating difficulty and low wavelength sensitivity. The PCF has four layers of air holes, which dramatically reduces the optical fiber loss and is more conducive to the application of sensors in actual production. In addition, by introducing dual cores on the upper and lower sides of the central air hole, reducing the spacing between the core and the gold nanolayer, a stronger evanescent field can be generated in the cladding air hole. The optical fiber sensor can detect the refractive index of two samples simultaneously with a maximum sensitivity of 21300 nm/RIU. To the best of our knowledge, the sensitivity achieved in this work is the highest sensitivity with the dual sample synchronous detection sensors. The detection range of the refraction index is 1.35-1.41, and the resolution of the sensor is 4.695×10^-6. Overall, the sensor will be suitable for medical detection, organic chemical sensing, analyte detection, and other fields.     

基于表面等离子体共振和定向耦合的D形光子晶体光纤折射率和温度传感器

利用光子晶体光纤结构的灵活性和性能的优越性, 设计了一种基于D形光子晶体光纤的折射率和温度传感器. 在D形光子晶体光纤表面抛磨并镀上金纳米薄膜, 作为表面等离子体共振传感通道用来测量液体折射率; 在包层的一个空气孔中填充温敏液体甲苯, 作为定向耦合通道实现对温度的测量. 进一步的数值计算发现, 基于定向耦合效应的温度传感和基于表面等离子体共振的折射率传感相互独立, D形光子晶体光纤同时进行折射率和温度传感检测. 在各向异性的完美匹配层边界条件下利用全矢量有限元法对该传感器特性进行了数值研究, 发现D形光子晶体光纤的空气孔直径决定了定向耦合吸收峰的中心波长和温度传感的灵敏度, 金薄膜的厚度和D形结构的抛磨深度仅影响表面等离子体共振峰的相对强度. 结果表明: 该传感器在-10–80 ℃的温度范围内具有11.6 nm/℃的温度灵敏度, 在1.34–1.44折射率范围内折射率灵敏度最高可达26000 nm/RIU.     

Long period grating cascaded to photonic crystal fiber modal interferometer for simultaneous measurement of temperature and refractive index

We propose and demonstrate a novel and simple dual-parameter measurement scheme based on a cascaded optical fiber device of long-period grating (LPG) and photonic crystal fiber (PCF) modal interferometer. The temperature and refractive index (RI) can be measured simultaneously by monitoring the spectral characteristics of the device. The implemented sensor shows distinctive spectral sensitivities of -30.82 nm/RIU (refractive index unit) and 47.4 pm/°C by the LPG, and 171.96 nm/RIU and 10.4 pm/°C by the PCF modal interferometer. The simultaneous measurement of the temperature and external RI is experimentally demonstrated by the sensor. The temperature shift and RI shift calculated by the sensor matrix agree well with the actual temperature and RI change in the experiment.     

Numerical analysis of a photonic crystal fiber based on two polarized modes for biosensing applications

This paper presents a theoretical study on a photonic crystal fiber plasmonic refractive index biosensor. The proposed photonic crystal fiber sensor introduces the concept of simultaneous detection with the linearly polarized and radially polarized modes because the sensing performance of the sensor based on both modes is relatively high, which will be useful for selecting the modes to make the detection accurately. The sharp single resonant peaks of the linearly polarized mode and radially polarized mode, are stronger and more sensitive to the variation of analyte refractive index than that of any other polarized mode in this kind of photonic crystal fiber. For linearly polarized mode and radially polarized mode, the maximum sensitivities of 10448.5nm per refractive index unit and 8230.7nm per refractive index unit can be obtained, as well as 949.8 and 791.4 for figure of merits in the sensing range of 1.33-1.45, respectively. Compared with the conventional Au-metalized surface plasmon resonance sensors, our device is better and can be applied as a biosensor.     

基于光子晶体光纤交叉敏感分离的磁场温度传感研究

提出了一种基于定向耦合效应和表面等离子共振效应的交叉敏感分离的磁场温度传感结构.在光子晶体光纤的一个特定空气孔中填充磁流体,利用磁流体的磁光效应和定向耦合效应形成磁场传感通道;在垂直方向的另一空气孔的内壁镀金纳米薄膜并填充甲苯液体,利用甲苯的温敏效应和表面等离子共振效应形成温度传感通道.对应输出谱出现两个损耗峰,测量损耗峰位置可以间接测出磁场强度和温度变化.通过理论计算()和结构优化,在90—270 Oe1 Oe=10~3/(4π) A/m范围内,磁场强度的灵敏度最高可达1.16 nm/Oe;在25—60?C范围内,温度的灵敏度可达-9.07 nm/?C.虽然填充的两种液体的折射率都受环境温度的影响,但通过建立灵敏度系数矩阵,可以消除磁场强度与温度的交叉敏感,实现磁场温度双参量的高灵敏度检测.     

Highly sensitive photonic crystal fiber biosensor based on titanium nitride

A highly sensitive surface plasmon resonance photonic crystal fiber (PCF) biosensor based on Titanium Nitride (TiN) as a new alternative plasmonic material is proposed and analyzed. The TiN has high stability, high conductivity, and corrosion resistance which make it an ideal material for nanofabrication. The suggested biosensor is analyzed by full vectorial finite element method with perfectly matched layer as boundary conditions. In this paper, the biosensor geometrical parameters are studied to achieve high sensitivity for both polarized modes. A refractive index sensitivity of 7700 and 3600 nm/RIU for quasi-transverse electric and quasi transverse magnetic modes, respectively, are obtained. Additionally, the reported biosensor could be used for detecting an unknown analyte refractive index ranging from 1.32 to 1.34 with a high linearity. Further, the proposed biosensor structure is easy for fabrication using standard PCF fabrication current technologies.     

Polarization detection analysis of dual-channel surface plasmon resonance sensing for silicone oils based on the D-shaped fiber with a central hole

We present and numerically characterize a dual channel surface plasmon resonance (SPR) sensor based on a D-shaped fiber with a central hole for silicone oil detections. The proposed design incorporates two metalized channels to facilitate the simultaneous detection of one group of silicone oils, which can consist of two different species. It has been demonstrated that the p-polarized input light can induce two peaks among surface plasmon resonance places, which come from the coupling between the core-guided mode and the fundamental surface plasmon polariton (SPP) modes at the D-shaped surface and around the central hole surface. However, the s-polarized input light can only induce one peak among surface plasmon resonance places, which comes from the coupling between the core-guided mode and the fundamental SPP mode around the central hole surface. The simulation results show that the characteristic responses of two channels independently correspond to the refractive index variations in the silicone oils with which they are in contact. A maximum sensitivity of 3500 nm/RIU (refractive index unit) and 4400 nm/RIU are achieved for channel A and B, respectively. This kind of sensor structure and polarization related demodulation method is promising in the simultaneous multi-analytes sensing applications in the future.     

倾斜光纤光栅溶液折射率传感器的实验研究

根据倾斜光纤光栅(TFBG)和表面镀金的TFBG传感器测量折射率的基本原理,通过OptiGrating软件模拟了不同浓度溶液下TFBG的透射谱和芯层模与某阶包层模耦合引起的谐振峰,初步得出了TFBG各阶包层模随着外界折射率的增大而向右偏移、在一定的传感范围内中心波长与外界折射率呈线性关系的结论。用小型离子溅射仪对TFBG镀45 nm厚度左右的金膜,并用扫描电镜在微观上观察镀膜效果。通过不同浓度下的NaCl溶液、MgCl₂溶液、CaCl₂溶液实验,对比研究了裸TFBG和镀金TFBG传感器对溶液折射率的传感特性。从而验证了模拟仿真得出的结论并定量分析得知：镀金后具有表面等离子体共振的TFBG溶液折射率灵敏度大于500 nm·RIU-1,而裸TFBG为2 nm·RIU-1左右,大约提高了200～300倍,且在一定范围内中心波长与溶液折射率的线性拟合度都在0.99以上。     

Photonic crystal fiber sensor based on hybrid mechanisms: Plasmonic and directional resonance coupling

We propose a special refractive index sensor design based on a photonic crystal fiber. Two analyte channels are introduced, with one analyte channel coated with gold layer and the other one without gold layer. A hybrid resonance method is used in the sensor to achieve a large dynamic index range, where surface plasmon resonance occurs when the analyte index is lower than that of the fiber material, while the core mode couples with the resonant mode of the adjacent analyte-filled cylinder when the analyte index is larger than the fiber material. When considering fluorinated polymer fibers, a broad index range of analyte refractive index from 1.25 to 1.45 with high sensitivity can be achieved. The maximal sensitivities reach 1.4 × 10⁴ nm/RIU and 2.7 × 10⁴ nm/RIU respectively when refractive index is in the range of 1.25 to 1.383 and 1.383 to 1.45. The sensor characteristics, make this simple sensor very interesting for detecting a wide range of fluid's refractive index or chemical agent concentration.     

Photonic crystal microcavity as a highly sensitive platform for RI detection

In this paper, we propose a new design principle of two-dimensional photonic crystal refractive index sensors with high transmission and sensitivity simultaneously. The proposed sensor is made of two waveguide couplers and one microcavity which is obtained by varying the radius of one air hole in the center of PC structure. The microcavity is separated from the input and output waveguides by many holes of the PC. It is shown that by injecting an analyte such as gas or a liquid into a sensing hole, and thus changing its refractive index, a shift in the resonant wavelength may occur. The transmission spectra, quality factor and sensitivity of the sensor have been analyzed numerically by the finite difference time domain (FDTD) method. The sensitivity value of the sensor has been found to be 668 nm/(RIU with minimum detection limit of 0.002 RIU), which proves the ability of the structure to produce biosensor PhC.     

Characterization of specially designed polarization maintaining photonic crystal fiber from far field radiation patterns

We report the development of theory and experiment for the characterization of polarization maintaining photonic crystal fiber (PM PCF) from far field intensity measurements. In this specially designed photonic crystal fiber, the air hole diameters along orthogonal axes adjacent to the core region are different, and hence create an effective index difference between the two orthogonal polarization modes. From the experimental measurements of the far field radiation pattern, we obtain transmission characteristics of PM PCF in terms of mode field diameters (MFD), V-values along major and minor axes, mode field area, birefringence, core radius, effective refractive index of cladding and numerical apertures along major and minor axes of PM PCFs. It is shown that the experimentally obtained geometrical and wave guiding parameters of the PM PCF match with the manufacturer/simulation/scanning electron microscope (SEM) data within the experimental limits.     

孪生孔光子晶体光纤

在光子晶体光纤典型的空气孔三角形排布图案中,将每个空气孔替换为一对孪生空气孔对,孪生空气孔对之间有确定的间距和固定的轴向,并由其形成包层的基本单元.在端面中心位置缺失一孪生空气孔对,由高折射率的背景材料将光场束缚于此形成纤芯.在包层中所有的孪生空气孔对按照三角形规则均匀排列.在这种新型结构中,由于所有孪生空气孔对都具有相同轴向而使得两个正交方向上的折射率不对称,从而导致双折射效应.本文利用有限差分法进行数值计算,所设计孪生空气孔对光子晶体光纤在两个正交方向上的折射率差Δneff可达到10－4.孪生空气孔对结构参量可在一定程度上影响双折射效果,增大空气孔或减小孪生空气孔对内部间距都可在一定程度上增大双折射效应.     

混合导引型光子晶体光纤中纤芯折射率相关的导光特性研究

利用全矢量有限元法研究了一种混合导引型光子晶体光纤在纤芯折射率改变时,光纤导光机理和模式的演变特性.当纤芯折射率小于混合包层中空气孔包层的有效折射率时,芯模的导光机理为"双带隙导引型";当纤芯折射率位于空气孔和高折射率两套包层的有效折射率之间时,芯模的导光机理为"单带隙+全内反射导引型";当纤芯折射率大于高折射率棒包层的有效折射率时,芯模的导光机理为"全内反射导引型".并对该光纤在上述三种条件下的导光特性进行了比较和讨论.这些结果对设计特殊用途的光子晶体光纤具有指导意义. 关键词： 混合导引型光子晶体光纤 带隙 模式     

Design of a highly sensitive photonic crystal waveguide platform for refractive index based biosensing

In this paper, a photonic crystal waveguide platform on silicon-on-insulator substrate is proposed in order to realize a highly sensitive refractive index based biosensor. Following the design, the analysis of the sensor structure are made by using the three dimensional Finite Difference Time Domain method. The principle of sensing is based on the change in refractive index, which in turn changes the output spectrum of the waveguide. Results show that the sensitivity of the sensor depends mainly on the geometrical properties of the defect region of the photonic crystal structure. The phenomenon is verified for various samples having refractive index ranging from 1 (air) to 1.57 (Bovine serum albumin). Further, the structure is compared with few other conventional photonic crystal waveguide designs to analyze the sensing performance. The estimated value of sensitivity of the sensor is found to be 260 nm/RIU with a detection limit of 0.001 RIU. This high sensitivity can enhance the performance of low-concentration analytes detection.     

螺旋形塑料光纤表面等离子体共振折射率传感器

研究了基于波长调制的螺旋形塑料光纤(plastic optical fiber, POF)表面等离子体共振(surface plasmon resonance, SPR)折射率传感器。采用机械热压和扭曲法将塑料光纤制备成螺旋形,在螺旋形POF上通过磁控溅射蒸镀一定厚度(约50 nm)的金属薄膜来激励SPR效应,从而形成螺旋形POF-SPR传感器。通过对螺旋形POF-SPR传感器的结构进行修饰,研究不同结构参数对折射率传感特性的影响。实验结果表明:由厚度为500μm扁平形POF扭制、螺纹数为4的螺旋形POF-SPR传感器具有较好的线性度和折射率传感特性,在折射率为1.335～1.400范围内测得的灵敏度为1 262 nm/RIU。该传感器具有成本较低、制备简单、结构稳定等优点。     

Design and optimization of nano-column array based surface plasmon resonance sensor

In this paper, a surface plasmon resonance fiber sensor based on gold nano-column array instead of gold film is designed and optimized. The finite element method is used to optimize the diameter of the nano-gold column under the consideration of figure of merit, which relates to the sensitivity, resonance wavelength and resonance intensity. The optimized sensor has 70 nm gold nano-column coated on a side polished single mode fiber. The results show that the average sensitivity reaches 5318 nm/RIU when the environmental refractive index changing from 1.33 to 1.39 RIU, which is much higher than those in the conventional surface plasmon resonance structure. The optimizes design will serve a vital foundation to the fabrication of high performance fiber optic surface plasmon resonance sensors based on nano metallic structure.     

光子晶体光纤的弯曲损耗振荡特性分析

综合运用弯曲光纤的等效直光纤模型、全矢量频域有限差分法及各向异性完全匹配层吸收边界,计算了两种类型(折射率引导型和带隙型)光子晶体光纤(PCF)的弯曲损耗.通过数值模拟弯曲损耗随弯曲半径的变化关系,证实了两种光子晶体光纤均具有弯曲损耗振荡特性.进而分析了两种光子晶体光纤弯曲损耗振荡的产生机理并给出了与损耗峰对应的包层模式.结果表明,振荡的产生源于基模与包层模式的耦合,其中,折射率引导型光子晶体光纤的弯曲损耗振荡机理类似于传统双包层光纤,带隙型光子晶体光纤弯曲损耗振荡的产生则是两种不同类型的包层模式共同作用的结果.     

Surface plasmon resonance-induced tunable polarization filters based on nanoscale gold film-coated photonic crystal fibers

Surface plasmon resonance induced tunable polarization filters based on nanoscale gold film-coated photonic crystal fibers were proposed and analyzed. The characteristics of the polarization filter were calculated by finite element method(FEM). The gold film was selectively coated on the inner wall of one cladding air hole which was located near the fiber core along the y-axis direction. When the phase of core fundamental mode and surface plasmon polaritons(SPPs) mode matches,the two modes couple with each other intensely. Numerical results show that the resonance wavelength and strength vary with fiber structural parameters and the index of the infilling liquid. The fiber parameters were optimized to achieve specific functions. Under the optimal structure, we realized a dual channel filter at the communication wavelength of 1.31 μm and1.55 μm for y polarization direction and x polarization direction. Then a single channel polarized filter at the communication wavelength of 1.55 μm is also achieved by adjusting the refractive index of the infilling liquid. The proposed polarization filters realized dual channel filtering and single channel filtering simultaneously under the same structure for the first time to the best of our knowledge.     

基于无芯光纤的多参数测量传感器

设计并制作了一种基于单模-无芯-单模-无芯-单模光纤结构的马赫-曾德尔传感器,可用来同时测量折射率和温度.该传感器中,两处无芯光纤充当输入、输出耦合器,中间单模光纤作为传感臂.利用有限元仿真和理论分析,确定耦合器和传感臂的最优长度为15 mm.在无芯光纤中激发出的高阶模进入单模光纤的包层传输,由于倏逝场的作用,受到环境折射率和温度的影响.选取透射谱不同干涉级次的波谷作为研究对象,实现了折射率和温度的同步测量.实验结果表明:1545 nm附近干涉谷的折射率和温度灵敏度分别为–153.89 nm/RIU(refractive index unit)和0.166 nm/℃;1570 nm附近干涉谷的折射率和温度灵敏度分别为–202.74 nm/RIU和0.183 nm/℃.该传感器在实现折射率和温度同步测量的同时,仍能保持较高灵敏度,在生物医疗等方面有着较好的应用前景.