Effect of secondary electrons from latent tracks created in YBCO by swift heavy ion irradiation

Swift heavy ions (SHI) with electronic energy loss exceeding a value of 14.4 keVnm⁻¹ create amorphized latent tracks in YBCO type superconductors. In the low fluence regime of an ion beam where tracks do not overlap, a decrease of the superconducting transition temperature as probed through resistivity studies, is not expected due to availability of percolating current paths. The present study however shows T_c decrease by about 1–3 K in thin films of YBCO when irradiated by 250 MeVAg ions at 79 K at a fluence of 5×10¹⁰–1×10¹² ionscm⁻². The highest fluence used in the present study is three times less than the fluence where track overlapping becomes significant. The T_c tends to increase towards the preirradiation value on annealing the films at room temperature. To explain this unusual result, we consider the effect of ion irradiation in inducing materials modification not only through creation of amorphized latent tracks along the ion path, but also through creation of atomic disorder in the oxygen sublattice in the Cu–O chains of YBCO by the secondary electrons. These electrons are emitted radially from the tracks during the passage of the SHI. Considering the correlation between the charge state of copper and its oxygen coordination, we show in particular that the latter process is a consequence of the inelastic interaction of the SHI induced low-energy secondary electrons with the YBCO lattice, which result in chain oxygen disorder and T_c decrease.     

MgO衬底上YBa2Cu3O7-δ台阶边沿型约瑟夫森结的制备及特性

MgO衬底上的YBa2Cu3O7-δ(YBCO)台阶边沿型约瑟夫森结(台阶结)在高灵敏度高温超导量子干涉器(superconducting quantum interference device,SQUID)等超导器件研制方面具有重要的应用价值和前景.本文对此类YBCO台阶结的制备和特性进行了研究.首先利用离子束刻蚀技术和两步刻蚀法在MgO(100)衬底上制备陡度合适、边沿整齐的台阶,然后利用脉冲激光沉积法在衬底上生长YBCO超导薄膜,进而利用紫外光刻制备出YBCO台阶结.在结样品的电阻-温度转变曲线中,观测到低于超导转变温度时的电阻拖尾现象,与约瑟夫森结的热激活相位滑移理论一致.伏安特性曲线测量表明结的行为符合电阻分路结模型,在超导转变温度TC附近结的约瑟夫森临界电流密度TC随温度T呈现出(TC-T)^2的变化规律,77 K时JC值为1.4×10^5 A/cm^2.利用制备的台阶结,初步制备了YBCO射频高温超导SQUID,器件测试观察到良好的三角波电压调制曲线,温度77 K、频率1 kHz时的磁通噪声为250μΦ0/Hz^1/2.本文结果为进一步利用MgO衬底YBCO台阶结研制高性能的高温超导SQUID等超导器件奠定了基础.     

Coulomb-Gas scaling law for a superconducting Bi(2+y)Sr(2-x-y)La(x)CuO(6+delta) thin films in magnetic fields

The electrical transport properties of epitaxial superconducting Bi(2+y)Sr(2-x-y)La(x)CuO(6+delta) thin films have been studied in magnetic fields. Using a modified Coulomb-gas scaling law, we can fit all the magnetic field dependent low resistance data with a universal scaling curve, which allows us to determine a relation between the activation energy of the thermally activated flux flow resistance and the characteristic temperature scaling parameters.     

Observation of defects and growth orientations of YBa2Cu3Ox thin films with YSZ buffer layers on Si

We have investigated defects and in-plate orientations of YBa₂Cu₃O_x thin films prepared by pulsed laser deposition (PLD) with YSZ as a buffer layer. The films showed c-axis oriented growth with the transition temperature T_co up to 87 K. Several types of defects including thermally induced cracks, grain boundaries and outgrowths were observed by scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM). The grain boundary provided a favorable path for crack propagation. The outgrowths nucleated on the YSZ surface grew with stoichiometric composition. According to X-ray diffraction (XRD) and HRTEM studies the YSZ buffer layer grew with the orientation relationship, YSZ110//Si110 and YSZ(001)//Si(001) up to the YBCO/YSZ interface. The superconducting YBCO films on top grew mainly with YBCO100//Si110 and YBCO(001)//Si(001), with some minor portions of YBCO110//Si110 and YBCO(001)//Si(001).     

In situ grown epitaxial YBa2Cu3O7 − x thin films by pulsed laser deposition under reduced oxygen pressure during cool-down time

We report novel pulsed laser deposition conditions that were used to obtain superconducting epitaxial YBCO thin films, grown in situ using an oxygen pressure lower than the usual one during the cool-down time. We studied the influence of the PLD conditions as substrate temperature, oxygen pressure, laser fluence, and number of laser pulses on the crystallographic and morphological features, and on the superconducting properties of the films. Good superconducting properties were obtained without a high temperature post-deposition annealing process. A maximum critical temperature of 88.6 K was obtained.     

Tuning the absorption band in the THz range of YBCO films patterned by means of HEHI lithography

High energy heavy ion lithography was used for modulating through implanted nanostructures the local structural and electrical properties of high temperature superconducting YBa₂Cu₃O₇ films. The controlled reduction of the critical temperature of irradiated films results in a localization into heavy ion patterned micro-regions of the electrical dissipation, viable in a given temperature range and driven by ion fluence, bias current and applied magnetic field. The measurement of the response of such nanostructured YBCO films to electromagnetic radiation in the infrared band (MIR–FIR region) is presented. It turns out that the ion induced structural modification of both superconducting film and substrate is actually enabling the infrared optical absorption of YBCO, so that the viability of low noise THz detection above the liquid nitrogen temperature is shown.     

Modulation of the electronic states of perovskite SrCrO3 thin films through protonation via low-energy hydrogen plasma implantation approaches

Hydrogenation of transition metal oxides offers a powerful platform to tailor physical functionalities as well as for potential applications in modern electronic technologies.An ideal nondestructive and efficient hydrogen incorporation approach is important for the realistic technological applications.We demonstrate the proton injection on SrCro3 thin films via an efficient low-energy hydrogen plasma implantation experiments,without destroying the original lattice framework.Hydrogen ions accumu-late largely at the interfacial regions with amorphous character which extend about one-third of the total thickness.The Hx.SrCro3(HSCO)thin films appear like exfoliated layers which however retain the fully strained state with distorted perovskite structure.Proton doping induces the change of Cr oxidation state from Cr^4+to Cr^3+in HSCO thin films and a transition from metallic to insulat-ing phase.Our investigations suggest an attractive platform in manipulating the electronic phases in proton-based approaches and may offer a potential peeling off strategy for nanoscale devices through low-energy hydrogen plasma implantation approaches.     

Peak effect at microwave frequencies in swift heavy ion irradiated YBa2Cu3O7-δ thin films

The vortex dynamics at microwave frequencies in YBa₂Cu₃O_7-δ (YBCO) films have been studied. We observe a peak in the microwave (4.88 and 9.55 GHz) surface resistance in some films in magnetic fields up to 0.8 T. This is associated with the ‘peak-effect’ phenomenon and reflects the order-disorder transformation of the flux line lattice near the transition temperature. Introduction of artificial pinning centers like columnar defects created as a result of irradiation with 200 MeV Ag ion (at a fluence of 4×10¹⁰ ions/cm²) leads to the suppression of the peak in films previously exhibiting ‘peak effect’.     

Metastable phases in YBCO films created by short-term annealings

The effect of short-term low-temperature annealing in air and in vacuum on the properties of HTSC films of YBCO is studied. It is shown that, under certain conditions of preparation of initial samples, a transition from the HTSC phase with the superconducting transition temperature T_c=90 K to a phase with T_c=60 K occurs without a noticeable change in the oxygen content. It is found that, as a result of short-term annealings, a transition from the HTSC phase with T_c=60 K to the phase with T_c=90 K can occur only through the vacuum annealing stage, which converts the sample into the superconducting state. Short-term annealings lead to multiple reversible “switching” of the films from one phase to another. The obtained results are of practical interest, since the proposed method can be used to quickly obtain superconducting YBCO films in various phase states. It is shown, in addition, that the annealing procedure makes it possible not only to increase the oxygen concentration but also to produce a structural rearrangement of a YBCO film.     

质子对BaTiO3薄膜辐照损伤的计算机模拟

本文先应用分子动力学模拟BaTiO₃体系在初级击出原子(primary knock-on atom, PKA)轰击下缺陷产生和复合的动力学过程, 模拟结果表明：PKA的方向和能量对缺陷数目有重要影响, 并计算了Ba, O和Ti原子的平均位移阈能分别为69 eV, 51 eV和123 eV, 远大于SRIM程序默认的位移阈能25 eV. 然后应用蒙特卡罗软件包SRIM, 模拟质子在BaTiO₃薄膜中的能量损失过程, 比较位移阈能对模拟结果的影响, 分析质子能量和入射角度对空位数量以及分布的影响. 结果表明空位数量随着质子能量增加而增加, 增加的速率随能量的增加是降低的;当入射角度大于60°, 空位数量随入射角增大而明显减少.     

GaInP/GaAs/Ge三结太阳电池不同能量质子辐照损伤模拟

以GaInP/GaAs/Ge三结太阳电池为研究对象,开展了能量为0.7, 1, 3, 5, 10 MeV的质子辐照损伤模拟研究,建立了三结太阳电池结构模型和不同能量质子辐照模型,获得了不同质子辐照条件下的I-V曲线,光谱响应曲线,结合已有实验结果验证了本文模拟结果,分析了三结太阳电池短路电流、开路电压、最大功率、光谱响应随质子能量的变化规律,利用不同辐照条件下三结太阳电池最大输出功率退化结果,拟合得到了三结太阳电池最大输出功率随位移损伤剂量的退化曲线.研究结果表明,质子辐照会在三结太阳电池中引入位移损伤缺陷,使得少数载流子扩散长度退化幅度随质子能量的减小而增大,从而导致三结太阳电池相关电学参数的退化随质子能量的减小而增大.相同辐照条件下,中电池光谱响应退化幅度远大于顶电池光谱响应退化幅度,中电池抗辐照性能较差,同时中电池长波范围内光谱响应的退化幅度比短波范围更大,表明中电池相关电学参数的退化主要来源于基区损伤.     

Interplay of self-doping and disorder in epitaxial Bi2Sr2Ca(n-1)Cu(n)O(2n+4+x) (n = 1,2) thin films under heavy-Ion irradiation

We propose a novel mechanism for the modification of T(c) in Bi(2)Sr(2)Ca(n-1)Cu(n)O(2n+4+x) epitaxial thin films (2212 and 2201) under energetic heavy-ion irradiation. By irradiating films with various oxygen content, we show from the temperature dependence of the resistance that irradiation always produces a doping effect superimposed on the damage caused to the sample. The effect is larger in 2201 than in 2212 thin films. The T(c) decrease observed by irradiating optimally doped films is partially due to this doping effect. Irradiation of semiconducting samples restores metallic superconducting behavior.     

低能离子对高温超导YBa_2Cu_3O_(7-δ)薄膜的表面改性和机理

低能氩离子束轰击并后退火处理的离子束表面改性,会影响高温超导薄膜的表面结构和超导特性,但是其中的深刻微观机理不清楚.本文通过连续改变离子束轰击时间,系统研究了离子束表面改性对于超导膜结构和临界电流密度的影响.通过扫描电子显微镜、X射线衍射、J_(c-scanning)测试表征样品的结构特性和超导特性,并得出内应变、氧空位缺陷等参量.研究表明,经过表面改性的钇钡铜氧(YBa_2Cu_3O_(7-δ),YBCO)薄膜,随轰击时间增加表面形貌会变得更加均匀致密,a轴晶粒消失,并且临界电流密度有了显著的提高.由化学键收缩配对模型分析得出,临界电流密度的提高与薄膜内应变增大和引发的局部YBCO结构中Cu—O键收缩有关.     

Investigation on FR(LT)–FR(HT) phase transition and pyroelectric properties of pulsed laser deposited Pb(Zr0.93Ti0.07)O3 thin films

The preparation process, crystallinity and electrical properties of pulse laser deposited Pb(Zr_xTi_1−x)O₃ (PZT) thin films were investigated in this paper. PZT (x = 0.93) thin film samples deposited at different substrate temperatures were prepared. Si (1 1 0) was the substrate; Ag and YBCO were the top electrode and the bottom electrode respectively. The bottom electrode YBCO was deposited on the Si substrate by pulsed laser deposition (PLD), and then PZT was epitaxially deposited on YBCO also by PLD. After annealing, the top electrode Ag was prepared on PZT by thermal evaporation, and then the Ag/PZT/YBCO/Si structured thin films were obtained. The XRD and the analysis of their electrical characters showed that, when the substrate temperature was elevated from 600 °C to 800 °C, the crystallinity and electrical properties of PZT thin films became better and better, and the F_R(LT)–F_R(HT) phase transition of PZT (x = 0.93) thin films occurred at 62 °C. The PZT film deposited at 800 °C had the best pyroelectric properties, and when the F_R(LT)–F_R(HT) phase transition of this film occurred, the peak value of pyroelectric coefficient (p) was obtained, with a value of 1.96 × 10⁻⁶ C/(cm² K). The PZT film deposited at 800 °C had the highest remnant polarization (P_r) and the lowest coercive field (E_c), with the values of 34.3 μC/cm² and 41.7 kV/cm respectively.     

The statistical distribution of magnetic critical currents determined by HTSC film morphology

An analysis is made of the geometric and morphological properties of YBCO superconducting films and of their effect on the magnetic and transport phenomena. A study is presented of the statistical characteristics of critical currents derived from the variation of trapped magnetic flux induced by passing a pulsed transport current. It is shown that the critical currents in the materials under study have a specific statistical distribution, whose main properties are due to the morphology of their structure and can be determined by geometric-probability analysis. The superconducting film is considered as a percolation system. An empirical normal-phase cluster-area distribution function was used to derive the distribution function of magnetic critical currents, which describes adequately the experimental data on how transport current affects trapped magnetic flux. The critical current for transition of a film to the resistive state has been calculated. Fiz. Tverd. Tela (St. Petersburg) 41, 1739–1742 (October 1999)     

采用MOD法在LAO上制备YBCO超导薄膜的Raman光谱研究

研究了TFA-MOD法在铝酸镧基体上制备YBCO超导薄膜时不同初始热处理温度对薄膜的影响。通过XRD、Ram an光谱和SEM等手段,对生长过程中的YBCO超导薄膜结构进行表征、分析,探讨了YBCO的生长机制。     

金属有机物化学气相法制备YBCO超导薄膜研究

运用金属有机物化学气相沉积法(MOCVD),在LaAlO3(LAO)单晶上沉积YBa2Cu3O7-x(YBCO)超导薄膜。通过使用优化的进液装置,使金属有机源连续、稳定地输送至蒸发皿进行闪蒸。通过优化总气压、氧分压等生长条件,获得高质量的YBCO薄膜。在固定的温度条件下,调节反应总气压和氧分压,在总压为380Pa,氧分压为180Pa获得YBCO薄膜临界电流密度Jc=0.6MA/cm2。随着氧分压增大,YBCO薄膜产生a轴取向,(005)峰向左偏移,且薄膜中的Cu/Ba由1.0变化至1.63。在Cu/Ba=1.48时,YBCO薄膜结构与性能较优。     

在金属基片上激光沉积YBCO超导薄膜

介绍了在金属基片上激光沉积缓冲层和ＹＢａ２Ｃｕ３ｏ７－ｘ（ＹＢＣＯ）高温超导薄膜的研究结果。在带ｙｔｔｒｉａ－ｓｔａｂｉｌｉｚｅｄ－ｚｉｒｃｏｎｉａ（ＹＳＺ）缓冲层的ＮｉＣｒ合金基片上,激光原位沉积出ＹＢＣＯ超导薄膜,薄膜的零电阻转变温度度４８Ｋ,７７Ｋ时临界电流密度约为２００Ａ／ｃｍ＾２;缓冲层的取向可以通过选择适当的沉积参数来改善;用扫描隧道电子显微镜对ＹＢＣＯ薄膜的微观结构分析表明：完善的螺     

Time resolved spectra of optical and electrical transient response induced by nanosecond laser pulses in amorphous AgInSbTe films

The phase transition dynamics of amorphous Ag₈In₁₄Sb₅₅Te₂₃ (AIST) thin films induced by single nanosecond laser pulses were studied by transient optical reflectivity and electrical resistance measurements with nanosecond resolution. Phase transition driven by nanosecond laser pulses can be achieved in a proper fluence range on AIST thin films. The results show that phase transition dynamics driven by nanosecond laser pulses was a multi-stage optical evolution process involving melt, solidification, recalescence, and recrystallion. However, it was found that the real-time responses of optical and electrical signals were quite different under the same irradiated condition. The recalescence process reflected by the second rising of optical reflectivity will not result in obvious changes in electrical resistance. The dependence of saturated time determined by optical and electrical evolution curve on laser pulse fluence was compared and analyzed. A two-dimensional percolation model was employed to explain the difference between electrical and optical transient responses.     

Control of the vortex flow in microchannel arrays produced in YBCO films by heavy-ion lithography

High-energy heavy-ion lithography is a powerful tool for tuning both structural and electromagnetic properties of high temperature superconductors by inducing nanometer scale defects confined in micron scale patterns. We show how the vortex dynamics in YBCO thin films patterned by heavy-ion lithography can be controlled and potentially exploited for device applications. Both local critical temperature and local critical currents are effectively tailored by the imposed irradiation geometry. The direct visualization of the real-time dynamics of the magnetic pattern is achieved by the magneto-optical imaging technique, while confined vortex flow is revealed by the simultaneous measurement of the electrical resistance both along and perpendicular (Hall resistance) to the direction of the applied current. It is shown that, for microchannel arrays inclined with respect to the transport current flow, the direction of vortex motion is solely determined by the imposed irradiation pattern geometry, in a well-defined temperature range, for a given applied current.