Vibrational Spectrometry Strategies for Quality Control of Procymidone in Pesticide Formulations

Abstract

Two vibrational spectrometry–based methodologies were developed for procymidone determination in wettable powdered pesticide formulations. The Fourier‐transform infrared (FTIR) procedure was based on the selective extraction of procymidone by chloroform and determination by peak area measurement between 1451 and 1441 cm^?1, using a baseline correction established between 1490 and 1410 cm^?1, and a precision of 0.4% and a limit of detection of 0.01% w/w procymidone for a sample mass of 25 mg were obtained. For FT‐Raman determination, the selected conditions were peak area measurement between 1005 and 995 cm^?1 Raman shift, with a baseline correction fixed between 1030 and 947 cm^?1, and a relative standard deviation of 1% and a limit of detection of 0.8% procymidone in the original sample were obtained. The sample frequency for FTIR determination was 30 hr^?1, lower than that for Raman with 40 hr^?1. FT‐Raman reduces to the minimum the reagent consumption and waste generation, also avoiding the sample handling and contact of the operator with the pesticide. It can be concluded that the proposed methods are appropriate for quality control in commercial pesticide formulations.     

Raman Spectroscopic Analysis of Perovskite-Structured Alkali Metal Fluorides Containing Nickel and Copper Ions

ABSTRACT

The mixed metal fluorides containing alkali metals have a range of important applications in optical and electronic devices. Raman spectrums of two such fluorides were examined. Raman spectrum of KCuF₃ at 300 K exhibited bands at 261, 295, 363, 468, 519, and 549 cm^?1, indicating site symmetry (orthorhombic) lower than the tetragonal symmetry as observed from the powder X-ray diffraction pattern. Cubic KNiF₃ showed bands at 410, 468, and 657 cm^?1. The first two bands were attributed to the second-order phonon scattering, and the band at 657 cm^?1 was assigned to two-magnon peak.     

An Infrared Method,with Reduced Solvent Consumption,for the Determination of Chlorsulfuron in Pesticide Formulations

A simple method has been developed for the determination of Chlorsulfuron in pesticide formulations by Fourier Transform Infrared (FTIR). Samples were diluted with CHCl_3^? , and the FTIR spectra of the samples and standards were obtained at a nominal resolution of 4 cm^? 1 from 4000 to 900 cm^? 1 with the accumulation of 25 scans. Chlorsulfuron determination was based on the measurement of peak area values from 1373 to 1363 cm^? 1 which were corrected by use of a two points baseline defined from 1401 to 1302 cm^? 1. The limit of detection achieved, which was of the order of 6 µg g^? 1, was appropriate for the determination of Chlorsulfuron in commercially available formulations. FTIR results were statistically comparable with those found by High Performance Liquid Chromatography (HPLC). The procedure reduces organic solvent consumption per sample to less than 3 ml CHCl₃, reduces waste generation and increases the sample measurement frequency up to 60 h^? 1.     

Carbonization in boron-ion-implanted polymethylmethacrylate as revealed from Raman spectroscopy and electrical measurements

ABSTRACT

The results of Raman spectroscopy and electrical measurements of 40 keV boron-ion-implanted polymethylmethacrylate with ion doses from 6.25 × 10¹⁴ to 5.0 × 10¹⁶ ions/cm² are reported for the first time. The Raman spectra recorded in the 400–3800 cm^?1 range, showing the formation of new carbon–carbon bands for the as-implanted samples at higher ion doses (>10¹⁶ ions/cm²), are found to be an additional support for carbonization processes earlier revealed by slow positrons. The current–voltage dependences at 360 K testify also that the as-implanted samples examined with higher fluences (3.75 × 10¹⁶ and 5.0 × 10¹⁶ ions/cm²) have created a very thin conductive layer or conductive joints due to carbonization.     

Investigation of L(+)-Ascorbic acid with Raman spectroscopy in visible and UV light

Abstract: Raman spectroscopy investigations of l(+)-ascorbic acid and its mono- and di-deprotonated anions (AH^? and A^2?) are reviewed and new measurements reported with several wavelengths, 229, 244, 266, 488, and 532 nm. Results are interpreted, assisted by new DFT/B3LYP quantum chemical calculations with 6-311++G(d,p) basis sets for several conformations of ascorbic acid and the anions. Raman spectra were measured during titration with NaOH base in an oxygen-poor environment to avoid fluorescence when solutions were alkaline. The ultraviolet (UV) absorption band for ascorbic acid in aqueous solution at ～247 nm was found to cause strong resonance enhancement for the ring C?C stretching mode (called B) at ～1692 cm^?1. The ascorbate mono-anion absorbs at ～264.8 nm giving Raman resonance enhancement for the same ring C–C bond stretching, downshifted to ～1591 cm^?1. Finally, for the ascorbate di-anion, absorption was found at ～298.4 nm with molar absorptivity of ～7,000 L mol^?1 cm^?1 and below ～220 nm. With UV light (244 and 266 nm), strongly basic solutions gave pronounced Raman resonance enhancement at ～1556 cm^?1. Relatively weak preresonance enhancement was seen for A^2? when excitation was done with 229 nm UV light, allowing water bands to become observable as for normal visible light Raman spectra.     

The Translation Mechanism of Smectite to Illite: An Infrared Spectroscopic Study of Ordered Mixed-Layer Illite/Smecite

The infrared spectral characteristics of ordered mixed-layer illite/smectite interstratified clay mineral with different mixed-layer ratios (S% = 5%, 10%, 15%, 20%, 25%, and 30%, where S% is mixed-layer ratio) from the Shihezi Formation of Late Permian in the Hanxing mining area, Hebei province of China, were studied by infrared spectroscopy. The results show that three infrared regions (3625 cm^?1±, 1200–1000 cm^?1, 850–700 cm^?1) changed with S%'s variation. The characteristic absorption bands of smectite at 3640 cm^?1, 1030 cm^?1, and 825 cm^?1 disappeared gradually with the decrease of S%, and the intensity of characteristic absorption bands of illite at 3625 cm^?1, 1100 cm^?1, 1024 cm^?1, 796 cm^?1, and 777 cm^?1 increased. These changes indicated that the illitization of smectite was realized by partial substitution of aluminum iron (Al³⁺) for silicon iron (Si⁴⁺) in silico-oxygen (Si–O) tetrahedron.     

Effect of uniaxial pressure on the Raman spectra of fluoro perovskites containing manganese with sodium or potassium

ABSTRACT

Perovskite structured mixed metal fluorides containing manganese/sodium or potassium have been synthesized in pure form by a greener precipitation route and characterized by high-resolution powder X-ray diffraction and Raman spectroscopy techniques. While all the reflections in the powder X-ray diffraction pattern of potassium manganese fluoride could be indexed in cubic symmetry with a = 4.1889 Å, sodium manganese fluoride showed reflections at positions typical of orthorhombic symmetry (Pnma space group) with a = 5.751, b = 8.008, and c = 5.548 Å. Potassium manganese fluoride in powder form showed bands at 209, 291, 386, 558, 621, and 733 cm^?1 in the Raman spectrum at room temperature. All these bands disappeared and second-order band at 1151 and 1298 cm^?1 emerged when the powders were compacted under pressure ranging between 1 and 4 tons (uniaxial). A similar change was noticed for sodium manganese fluoride in which bands at 1099, 1149, 1203, and 1286 cm^?1 were observed for the compacted samples. The response of the vibrational modes of these compounds to uniaxial pressure revealed the existence of large structural disorder in them. Additionally, the need for the extreme care to collect and interpret Raman data of polycrystalline samples of these systems has been illustrated through this study.     

Indole in Argon Matrix: The Near UV Spectra.

Abstract

The near UV absorption, steady-state polarized fluorescence excitation and time–-resolved fluorescence emission spectra of indole in argon matrix are reported. The absorption maxima of the four lowest singlet transitions were identified at 35095 cm^?1(also the S_{1, 0} 0–0 band), 37650 cm^?1 (S_2,0), 47415 cm^?1 (S_3,0), and 51680 cm^?1 (S_4,0). No distinct 0–0 band of the second transition was identified but the linearly polarized, steady-state fluorescence excitation spectrum indicates an onset of weak S_2,0 bands on the blue side of the S_1,0 0–0 peak (35095 + 400 cm^?1). Only one fluorescence emission component, of 4.9±0.2 ns, was obtained by excitation over the S_{1, 0} 0–0 + 565 cm^?1 to S_1,0 0–0 - 245 cm^?1 domain. The reported data strongly suggest the ¹L_b ^?1A₁ and ¹L_a ^?1A₁assignment for the lowest and next lowest transitions, respectively.     

Controlling the defect density to improve the output power of InGaN/GaN-based vertical light-emitting diodes by using substrates patterned with SiO2 lenses

In this study, we investigated the effect of SiO₂ lenses on the output power of InGaN/GaN-based vertical light-emitting diodes (VLEDs; wavelength = 445 nm) and compared the results to those of reference VLEDs without the SiO₂ lenses (planar samples). Arrays of SiO₂ lenses (pitch = 3 μm, width = 2.5 μm, height = 1.0 μm) were formed on c-plane sapphire substrates. The external quantum efficiency (EQE) of the packaged VLEDs with planar and patterned substrates was characterised. At 5 mA, the EQE of the patterned samples was 150% higher than that of the planar samples. A patterned, N-polar, n-GaN sample contained far fewer nanopipes (approximately 2.2 × 10⁵ cm^?2) than a planar n-GaN sample (approximately 2.4 × 10⁶ cm^?2). Furthermore, the patterned samples contained far fewer threading dislocations (approximately 1.0 × 10⁸ cm^?2) than the planar samples (approximately 5.0 × 10⁸ cm^?2). Scanning electron microscopy (SEM) images showed that the photoelectrochemical (PEC)-etched patterned samples contained cones that were 150% larger than that of the PEC-etched planar samples. In addition, SEM images, cathode luminescence measurements and finite-difference time-domain simulations were used to characterise the improved light output of the patterned samples.     

Changes in Dentin Collagen After Sample Grinding and Heating

ABSTRACT

Changes to the structure of the organic matrix of the dentin tissue were determined after sample grinding and heating. Powder dentin measuring 25–38 µm and slices with a thickness of about 50 µm were employed. Spectra acquisition was conducted with a Fourier-transform infrared spectrometer. The thermal treatment was performed between 100°C and 300°C, with steps of 25°C. After grinding, two bands (1283.5 ± 0.5 cm^?1 and 1240.7 ± 0.5 cm^?1) shifted to higher wavenumbers, while three bands (1339.5 ± 0.5 cm^?1, 1283.5 ± 0.5 cm^?1, and 1202.7 ± 0.5 cm^?1) shifted to lower wavenumbers after thermal treatment in the range 100–300°C; the band at 1283.5 ± 0.5 cm^?1 shifted only 2 cm^?1. Thermal treatment produced a wavenumber shift in the opposite direction compared with the shift produced after grinding. The observed changes in the vibration modes of the structure indicate that sample preparation or sterilization involving grinding and heating must be carefully evaluated in order to preserve the natural characteristic of the collagen structure.     

Vibrational Spectroscopy of the Borate Mineral Priceite—Implications for the Molecular Structure

ABSTRACT

Priceite is a calcium borate mineral and occurs as white crystals in the monoclinic pyramidal crystal system. We have used a combination of Raman spectroscopy with complimentary infrared spectroscopy and scanning electron microscopy with Energy-dispersive X-ray Spectroscopy (EDS) to study the mineral priceite. Chemical analysis shows a pure phase consisting of B and Ca only. Raman bands at 956, 974, 991, and 1019 cm^?1 are assigned to the BO stretching vibration of the B₁₀O₁₉ units. Raman bands at 1071, 1100, 1127, 1169, and 1211 cm^?1 are attributed to the BOH in-plane bending modes. The intense infrared band at 805 cm^?1 is assigned to the trigonal borate stretching modes. The Raman band at 674 cm^?1 together with bands at 689, 697, 736, and 602 cm^?1 are assigned to the trigonal and tetrahedral borate bending modes. Raman spectroscopy in the hydroxyl stretching region shows a series of bands with intense Raman band at 3555 cm^?1 with a distinct shoulder at 3568 cm^?1. Other bands in this spectral region are found at 3221, 3385, 3404, 3496, and 3510 cm^?1. All of these bands are assigned to water stretching vibrations. The observation of multiple bands supports the concept of water being in different molecular environments in the structure of priceite. The molecular structure of a natural priceite has been assessed using vibrational spectroscopy.     

A new application of nickel-boron amorphous alloy nanoparticles: anode-catalyzed direct borohydride fuel cell

In this work, an amorphous Ni-B alloy was synthesized by chemical reduction and used in a direct borohydride fuel cell (DBFC). Characterization of the catalyst structure, composition, and morphology was performed by XRD, EDX, TEM, and SEM. In addition, the results showed that Ni-B presents as amorphous nanoparticles. The particle diameters ranged from 22 to 25 nm. The cyclic voltammetry (CV) and chronoamperometry (CA) tests proved that Ni-B has better electrocatalytic activity and higher stability towards KBH₄ oxidation compared to a pure Ni catalyst. A single cell was assembled with a Ni-B anode and a LaNi_0.9Ru_0.1O₃ cathode. A peak power density of 180 mW cm^?2 was achieved at room temperature. In addition, the fuel utilization rate was approximately 41% at a constant current density of 200 mA cm^?2, illustrating that some BH₄ ^? hydrolysis occurs on the Ni-B surface. Finally, the cell had no attenuation after 180 h test, showing good stability.     

Benzoylferrocene-modified carbon nanotubes paste electrode as a voltammetric sensor for determination of hydrochlorothiazide in pharmaceutical and biological samples

The electrooxidation of hydrochlorothiazide (HCT) at the surface of a benzoylferrocene modified multi-walled carbon nanotube paste electrode was studied using electrochemical approaches. Under the optimized conditions (pH 7.0), the square wave voltammetric peak current of HCT increased linearly with HCT concentration in the ranges of 6.0?×?10^?7 to 3.0?×?10^?4 M. The detection limit was 9.0?×?10^?8 M HCT. The diffusion coefficient (D?=?1.75?×?10^?5 cm²/s) and electron transfer coefficient (α?=?0.45) for HCT oxidation were also determined. The proposed sensor was successfully applied for the determination of HCT in human urine and tablet samples.     

Effects of silicon negative ion implantation in semi-insulating gallium arsenide

ABSTRACT

In the present work, effects of silicon negative ion implantation into semi-insulating gallium arsenide (GaAs) samples with fluences varying between 1?×?10¹⁵ and 4?×?10¹⁷?ions?cm^?2 at 100?keV have been described. Atomic force microscopic images obtained from samples implanted with fluence up to 1?×?10¹⁷?ion?cm^?2 showed the formation of GaAs clusters on the surface of the sample. The shape, size and density of these clusters were found to depend on ion fluence. Whereas sample implanted at higher fluence of 4?×?10¹⁷?ions?cm^?2 showed bump of arbitrary shapes due to cumulative effect of multiple silicon ion impact with GaAs on the same place. GXRD study revealed formation of silicon crystallites in the gallium arsenide sample after implantation. The silicon crystallite size estimated from the full width at half maxima of silicon (111) XRD peak using Debye-Scherrer formula was found to vary between 1.72 and 1.87?nm with respect to ion fluence. Hall measurement revealed the formation of n-type layer in gallium arsenide samples. The current–voltage measurement of the sample implanted with different fluences exhibited the diode like behavior.     

A sensitive amperometric detection of dopamine agonist drug pramipexole at functionalized multi-walled carbon nanotubes (f-MWCNTs) modified electrode

The electrochemical detection of dopaminergic agonist drug pramipexole dihydrochloride monohydrate (PPX) has been investigated by cyclic voltammetric (CV) and amperometric i–t techniques at functionalized multi-walled carbon nanotubes-modified glassy carbon electrode. For the first time, a sensitive and rapid electrochemical method was developed for the determination of PPX. The surface morphological characteristics of the proposed electrode have been studied by using transmission electron microscopy (TEM); further, electrochemical impedance spectroscopy (EIS) and Fourier transform infrared spectroscopy (FTIR) have been employed. PPX shows an irreversible anodic peak, which may be ascribed to the oxidation of the –NH groups of PPX. The proposed method was showing good sensitivity of 0.993 μA μM^?1 cm^?2 with a linear range of 5 to 340 μM by amperometric i–t and CV technique shows a linear range of 12.5 to 313 μM with a sensitivity of 1.92 μA μM^?1 cm^?2. The recovery of PPX from blood serum samples was found 100.6 and 98.9 %, respectively. Furthermore, the proposed method has been demonstrated for the determination of PPX in commercially available pharmaceutical samples and good agreement of results obtained.     

CeO<Subscript>2</Subscript> and Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> modified Ni-YSZ anode for solid oxide fuel cell

Ni sintering at high temperature (～ 800 °C) operation drastically degrades the performance of Ni-yttria-stabilized zirconia (YSZ) anode in solid oxide fuel cell (SOFC). Mixed ionic and electronic conductive oxides such as CeO₂ and Nb₂O₅ enhance the dispersion of Ni, CeO₂ enhances the redox behavior and promotes charge transfer reactions, and Nb₂O₅ increases the triple phase boundary. In the present work, anode-supported SOFC is fabricated and tested in H₂ fuel at 800 °C. YSZ and lanthanum strontium manganite (LSM)-YSZ are used as the electrolyte and composite cathode with NiO-YSZ, CeO₂-NiO-YSZ, and Nb₂O₅-NiO-YSZ as an anode. The peak power density obtained for the cell with 10% CeO₂–30% NiO-YSZ anode at the 5 and 25 h of operation is 330 and 290 mW cm^?2 which is higher than that for 40% NiO-YSZ anode (275 mW cm^?2 at 5 h). The peak power density obtained for the cell with 10% Nb₂O₅–30% NiO-YSZ anode at the 5 and 25 h of operation is 301 and 285 mW cm^?2 which is higher than that for 40% NiO-YSZ anode (275 mW cm^?2 at 5 h). Physical characterization has been carried to study morphology, elemental analysis, particle size, and phase formation of the fabricated anode before and after cell operation to correlate the cell performance.     

Electron concentration dependence of exciton localization and freeze-out at local potential fluctuations in InN films

InN films with electron concentration ranging from n～10¹⁷ to 10²⁰ cm^?3 grown by metal–organic chemical vapor deposition (MOCVD) and molecular beam epitaxy (MBE) were investigated by variable-temperature photoluminescence and absorption measurements. The energy positions of absorption edge as well as photoluminescence peak of these InN samples with electron concentration above 10¹⁸ cm^?3 show a distinct S-shape temperature dependence. With a model of potential fluctuations caused by electron-impurity interactions, the behavior can be quantitatively explained in terms of exciton freeze-out in local potential minima at sufficiently low temperatures, followed by thermal redistribution of the localized excitons when the band gap shrinks with increasing temperature. The exciton localization energy σ _loc is found to follow the n ^5/12 power relation, which testifies to the observed strong localization effects in InN with high electron concentrations.     

Optimization of Pretreatment Method for Alkylmercuries Speciation in Coal by High‐Performance Liquid Chromatography Coupled with UV‐Digestion Cold Vapor Atomic Fluorescence Spectrometry

Abstract

Exhaustive extraction of analytes in their original chemical forms from samples with complex matrices is a pivotal step for speciation analysis. Herein we propose a pretreatment method for extracting and preconcentrating methylmercury and ethylmercury from coal samples by using KBr–H₂SO₄/CuSO₄–C₆H₅CH₃–Na₂S₂O₃ system. The extraction conditions, including the volume of the organic phase and the extraction time, were optimized in detail. Speciation analysis of alkylmercuries was carried out by high‐performance liquid chromatography online coupled with UV‐digestion and cold vapor atomic fluorescence spectrometry. The detection limits were 0.6 ng mL^?1 for methylmercury and 1 ng mL^?1 for ethylmercury, respectively. The recoveries of methylmercury and ethylmercury spiked in a sample were 84% and 82%, respectively. The method was applied successfully to analysis of alkylmercuries in four coal samples collected from northeast China.     

Electrical and structural studies of a LiBOB-based gel polymer electrolyte

A series of gel polymer electrolytes (GPEs) containing lithium bis(oxalato)borate (LiBOB), propylene carbonate (PC), and ethylene carbonate (EC) have been investigated. Poly(ethylene oxide) (PEO) was used as the polymer. First, a series of liquid electrolytes was prepared by varying the Li:O ratio and obtained the best composition giving the highest conductivity of 7.1?×?10^?3 S cm^?1 at room temperature. Then, the PEO-based GPEs were prepared by adding different amounts of LiBOB and PEO into a mixture of equal weights of EC and PC (40 % of each from the total weight). The gel electrolyte comprises of 12.5 % of LiBOB, 7.5 % of PEO, 40 % of EC, and 40 % of PC gave the highest ionic conductivity of 5.8?×?10^?3 S cm^?1 at room temperature. From the DC polarization measurements, ionic nature of the gel electrolyte was confirmed. Fourier transform infrared (FTIR) spectra of electrolytes showed the Li⁺ ion coordination with EC and PC molecules. These interactions were exhibited in the peaks corresponding to ring breathing of EC at 893 cm^?1 and ring bending of EC and symmetric ring deformation of PC at 712 and 716 cm^?1 respectively. The presence of free Li⁺ ions and ion aggregates is evident in the peaks due to the symmetric stretching of O–B–O at 985 cm^?1.     

Discrimination of Radix Angelicae Sinensis According to Harvest Time and Geographical Origin with Midinfrared Diffuse Reflectance Spectroscopy and Chemometric Methods

ABSTRACT

The combination of midinfrared (MIR) spectrum with chemometric methods provides an approach to study the Radix Angelicae sinensis (RAs) in relation to its geographical origin and harvest time. Random forests (RF) was applied to select the most effective wave-number variables from full MIR variables; as a result, three variables (3730 cm^?1, 2310 cm^?1, and 1050 cm^?1) were selected for the discrimination of different RAs. The selected effective wave-number variables were put into linear discriminant analysis (LDA) and radial basis function neural networks (RBF-NNs) to establish the classification models. For the independent test set, the overall accuracy was 96.67%, 93.33%, and 96.67% for RF, LDA, and RBF-NNs models, respectively. These results show that MIR combined with chemometric methods might be a suitable way to classify RAs.