基于铋可饱和吸收体的超快激光产生

采用磁控溅射沉积法在微纳光纤表面上镀一层纳米级厚度的铋薄膜,制备了一种微纳光纤-铋膜结构的可饱和吸收体.在1.5μm处的非线性光调制深度为14%.将其应用到掺铒光纤激光器中,在1.5μm波段获得稳定的超快脉冲激光产生,脉宽为357 fs,输出功率为45.4 mW,单脉冲能量为2.39 nJ,信噪比为84 dB.实验结果表明,利用磁控溅射法可制备出大调制深度的可饱和吸收体,为获得高能量超短脉冲激光输出提供新方案.     

Passively Q-switched fiber laser based on graphene saturable absorber

A passively graphene Q-switched Erbium doped fiber laser around 1.5 μm is demonstrated in this paper. The graphene saturable absorber was fabricated by sandwiching a thin graphene film produced via chemical vapor deposition between two FC fiber connectors. Stable pulse trains were obtained with the pulse repetition rate varying between 34.72 and 53.2 kHz and the average output power ranging from 0.504 mW to 0.926 mW. The achieved shortest pulse duration and highest pulse energy were 3.2 μs and 17.41 nJ, respectively.     

基于石墨烯可饱和吸收体的纳秒锁模掺铥光纤激光器

报道了一种基于石墨烯可饱和吸收体的纳秒锁模掺铥光纤激光器.该激光器采用环形腔结构,利用自制的三层石墨烯薄膜作为可饱和吸收体实现锁模.同时在腔内插入一个窄带光纤光栅,约束腔内起振的纵模数,适当调节抽运功率和偏振控制器的角度,得到了重复频率为3.8 MHz、脉宽在3.8—94.3 ns之间灵活可调的2μm纳秒锁模脉冲输出,整个脉宽调节范围超过90 ns.此外,由于获得的兆赫兹纳秒锁模脉冲时间带宽积在49—1119范围内,即存在强烈的啁啾,因而可作为2μm波段啁啾脉冲放大系统中的种子源使用.     

Nanosecond-pulsed erbium-doped fiber lasers with graphene saturable absorber

We demonstrate graphene mode-locked nanosecond erbium-doped fiber laser in an all-fiber ring cavity. The clean and robust pulse train was generated at 27 mW pump power. Resultant central wavelength, repetition rate and pulse width was 1560 nm, 388 kHz and 6 ns, respectively. With two stage fiber amplifier, the output power was 553 mW, corresponding to single pulse energy of 1.4 μJ. In addition, the pulse-width can be varied ranging from 3 ns to 20 ns at repetition rate between 200 kHz and 1.54 MHz by changing the length of the laser cavity.     

基于石墨烯的1064nm连续锁模超短脉冲激光器

介绍了利用沉积在增透镜上的石墨烯薄膜作为可饱和吸收体、808 nm激光二极管端面泵浦Nd∶YVO4晶体的1 064 nm连续锁模激光输出特性。采用W型折叠谐振腔结构,在808 nm泵浦功率为80 W时,有稳定的连续锁模脉冲输出,平均输出功率达到185 mW;当抽运功率增加到160 W时,获得了中心波长1 0634 nm、脉冲宽度为518 fs、重复频率为667 MHz、最大平均输出功率为323 mW的百飞秒量级超短脉冲激光输出。实验结果表明：石墨烯具有优良的可饱和吸收性,在1 064 nm波段能够实现高功率、百飞秒量级连续锁模脉冲激光输出。     

基于石墨烯的1 064 nm连续锁模超短脉冲激光器

介绍了利用沉积在增透镜上的石墨烯薄膜作为可饱和吸收体、808 nm激光二极管端面泵浦Nd∶YVO4晶体的1 064 nm连续锁模激光输出特性。采用W型折叠谐振腔结构,在808 nm泵浦功率为8.0 W时,有稳定的连续锁模脉冲输出,平均输出功率达到185 mW;当抽运功率增加到16.0 W时,获得了中心波长1 063.4 nm、脉冲宽度为518 fs、重复频率为66.7 MHz、最大平均输出功率为323 mW的百飞秒量级超短脉冲激光输出。实验结果表明:石墨烯具有优良的可饱和吸收性,在1 064 nm波段能够实现高功率、百飞秒量级连续锁模脉冲激光输出。     

氧化石墨烯被动调Q掺铒光纤激光器

报道了基于氧化石墨烯的被动调Q掺铒光纤激光器。激光器采用环形腔结构,调Q器件为自制的氧化石墨烯可饱和吸收镜。泵浦功率在81~505 mW范围内时,得到了重复频率68~124 kHz的稳定的调Q脉冲输出,脉宽为0.47~1.60 s。由于泵浦功率限制,激光器最大输出功率为10 mW, 相应单脉冲能量为80.6 nJ。此种基于氧化石墨烯可饱和吸收体的被动调Q光纤激光器体积小、成本低廉、结构简单、稳定性高、光束质量高,具有广阔的应用前景。     

Fundamental and harmonic mode-locking in erbium-doped fiber laser based on graphene saturable absorber

Graphene-based passively mode-locked erbium doped fiber laser is presented. Multilayer graphene was obtained by mechanical exfoliation of pure graphitic block and deposited on the fiber ferrule. The mode-locking performance was investigated under various laser pumping conditions. The laser could operate at fundamental repetition rate of 16.34 MHz with 844 fs pulse duration and 30 mW average output power. Also harmonic-mode locking of the laser is demonstrated. 294 and 800 MHz repetition rates were obtained (corresponding to the 18th and 49th harmonic of the fundamental repetition frequency, respectively) with nearly transform-limited pulses.     

Zinc-oxide/PDMS-clad tapered fiber saturable absorber for passively mode-locked erbium-doped fiber laser

We propose and demonstrate a passively mode-locked erbium-doped fiber laser(EDFL) based on zincoxide/polydimethylsiloxane(Zn O/PDMS) saturable absorber(SA) that evanescently interacts with the light on a tapered fiber. The Zn O/PDMS composite is coated on the whole surface of the tapered fiber to guarantee the maximum efficiency of the SA device, with a measured insertion loss of 0.87 d B and a modulation depth of 6.4%. The proposed laser can generate soliton mode-locking operation at a threshold power of 33.07 m W. The generated output pulse yields a repetition rate and pulse width of 9.77 MHz and 1.03 ps, respectively. These results indicate that the proposed Zn O/PDMS-clad tapered fiber could be useful as an efficient, compatible, and low-cost SA device for ultrafast laser applications.     

Q-switched Er-doped fiber laser with low pumping threshold using graphene saturable absorber

We propose a Q-switched Er-doped fiber laser(EDFL) with a threshold pumping power as low as 7.4 mW, and demonstrate using graphene polyvinyl alcohol(PVA) thin film as a passive saturable absorber(SA). The SA is fabricated from graphene flakes, which is synthesized by electrochemical exfoliation of graphite at room temperature in 1% sodium dodecyl sulfate aqueous solution. The flakes are mixed with PVA solution to produce a thin film, which is then sandwiched between two ferrules to form a SA and integrated in the EDFL ring cavity to generate a stable Q-switched pulse train. The pulse train operates at 1560 nm with a threshold pump power of 7.4 mW. At maximum 1480 nm pump power of 33.0 mW, the EDFL generates an optical pulse train with a repetition rate of 27.0 kHz and pulse width of 3.56 μs. The maximum pulse energy of 39.4 nJ is obtained at a pump power of 14.9 mW. This laser can be used as a simple and low-cost light source for metrology, environmental sensing, and biomedical diagnostics.     

Observation of wavelength-switchable solitons in an all-polarization-maintaining erbium-doped fiber cavity based on graphene saturable absorber reflector

We present the generation of wavelength-switchable single-polarization solitons in an all-polarization-maintaining erbium-doped fiber laser mode-locked by a graphene saturable absorber. Ultrashort pulses centered at the wavelength of 1531.6 nm with the duration of 816 fs and centered at the wavelength of 1557.8 nm with the duration of 402 fs are separately obtained from the same fiber laser cavity. The cavity loss adjusted by the gold reflector plays a crucial role in wavelength switching.     

An intrinsic fiber ring laser based sensor with saturable absorber

A novel configuration of fiber ring laser acoustic sensor, which adopts single-mode fiber as sensing element, is proposed and demonstrated. Linewidth less than 1 kHz is achieved by introducing a segment of erbium-doped fiber in the reflecting arm as saturable absorber. A polarization independent unbalanced Michelson interrogation interferometer and phase generated carrier demodulation technique are adopted to recover signal. Experiments demonstrate that the phase sensitivity is 0.018 rad/nm in good linearity and equivalent minimum detect able length change reaches 19.1 pm.     

Mode-locked fiber laser with MoSe_2 saturable absorber based on evanescent field

An all-fiber mode-locked fiber laser was achieved with a saturable absorber based on a tapered fiber deposited with layered molybdenum selenide(MoSe_2). The laser was operated at a central wavelength of 1558.35 nm with an output spectral width of 2.9 nm, and a pulse repetition rate of 16.33 MHz. To the best of our knowledge, this is the first report on mode-locked fiber lasers using MoSe_2 saturable absorbers based on tapered fibers.     

Multicore, tapered optical fiber for nonlinear pulse reshaping and saturable absorption

We present a new method to create a coupled waveguide array via tapering a seven-core telecommunications fiber. The fiber based waveguide array is demonstrated to exhibit the novel physics associated with coupled waveguide arrays, such as discrete diffraction and discrete self-focusing. The saturable absorber characteristics of the device are characterized and an autocorrelation measurement reveals significant single-pass pulse reshaping.     

Carboxyl graphene oxide solution saturable absorber for femtosecond mode-locked erbium-doped fiber laser

The carboxyl-functionalized graphene oxide(GO-COOH) is a kind of unique two-dimensional(2 D) material and possesses excellent nonlinear saturable absorption property and high water-solubility. In this paper, we prepare saturable absorber(SA) device by depositing GO-COOH nanosheets aqueous solution on a D-shaped fiber. The modulation depth(MD) and saturable intensity of the SA are measured to be 9.6% and 19 MW/cm~2, respectively. By inserting the SA into the erbium-doped fiber(EDF) laser, a passively mode-locked EDF laser has been achieved with the spectrum center wavelength of 1562.76 nm. The pulse duration, repetition rate, and the signal-to-noise ratio(SNR) are 500 fs, 14.79 MHz, and 80 dB,respectively. The maximum average output power is measured to be 3.85 mW. These results indicate that the GO-COOH nanosheets SA can be used as a promising mode locker for the generation of ultrashort pulses.     

Q-switched pulse generation from an all-fiber distributed Bragg reflector laser using graphene as saturable absorber

A Q-switched distributed Bragg reflector fiber laser using a graphene passive saturable absorber is proposed in a cavity consisting of a fiber Bragg grating and Faraday rotator mirror as end mirrors, together with a highly doped erbium-doped fiber as a gain source. The laser has a Q-switched threshold of about 28 mW and a tunable repetition rate of 10.4-18.0 kHz with varying pump power. The shortest pulse width obtained from the system is 3.7 its, with a maximum pulse energy and peak power of 22.2 nJ and 3.4 mW, respectively.     

High-energy saturable absorber mode-locked fiber laser system

We demonstrate a mode-locked erbium-doped fiber laser with a 1-microm InGaAs saturable absorber that produces 84-ps, 1-nJ transform-limited pulses. Measurements of the InGaAs multiple quantum well revealed a slow saturable absorber that is useful for passive mode locking. Optical fiber was added to extend the cavity and vary the repetition rate from 51 kHz to 5.4 MHz. The narrow spectral width of the laser output (<0.04 nm) permits amplification to 0.2 microJ/pulse with minimal pulse broadening. Pulse energies as large as 1.7 microJ can be achieved with pulse widths of <330 ps. Average powers of 0.5 W at megahertz repetition rates are demonstrated.     

Q-switched fiber laser using carbon platinum saturable absorber on side-polished fiber

A 1550 nm Q-switched fiber laser using a carbon platinum saturable absorber deposited on side-polished fiber(SPF) is proposed and demonstrated. The SPF is approximately 2 mm with a polarization-dependent loss(PDL)of 0.4 dB and an insertion loss of 2.5 dB. A stable Q-switched output spectrum is obtained at 1559.34 nm with a peak power of ~6 mW, a pulse width of 1.02 μs, pulse energy of 5.8 nJ, average output power of 0.76 mW, and a repetition rate of 131.6 kHz taken at a pump power of 230.0 mW. A signal-to-noise ratio of 49.62 d B indicates that the Q-switched pulse is highly stable.     

Femtoseconds soliton mode-locked erbium-doped fiber laser based on nickel oxide nanoparticle saturable absorber

We demonstrate a femtosecond mode-locked erbium-doped fiber laser(EDFL) using a nickel oxide(Ni O) as a saturable absorber(SA). Ni O nanoparticles are hosted into polyethylene oxide film and attached to fiber ferrule in the laser cavity. The Ni O-SA shows a 39% modulation depth with a 0.04 MW∕cm~2 saturation intensity. Our ring laser cavity based on erbium-doped active fiber with managed intracavity dispersion has the ability to generate ultrashort pulses with a full width at half-maximum(FWHM) of around 2.85 nm centered at 1561.8 nm.The pulses repeat at a frequency of 0.96 MHz and duration of 950 fs.     

A Q-switched erbium-doped fiber laser based on ZrS_2 as a saturable absorber

A passively Q-switched erbium-doped fiber(EDF) laser is proposed and demonstrated utilizing a zirconium disulfide(ZrS_2)-based saturable absorber(SA). ZrS_2 nanosheets are prepared, whose modulation depth,saturation intensity, and nonsaturable absorbance are measured to be 14.7%, 0.34 MW/cm~2, and 17.4%, respectively. Then, a Q-switched EDF laser is implemented by the ZrS_2-SA. The pulse repetition rate varies from 40.65 to 87.1 k Hz when the pump power changes from 55 to 345 mW. The shortest pulse width is 1.49 μs with pulse energy of 33.5 nJ. As far as we know, this is the shortest pulse width obtained by a ZrS_2-SA so far.