Tl2Ba2Ca2Cu3O10的化学键性质和同质异能位移研究

Tl2Ba2Ca2Cu3O10 was reported to be a superconductor with a highest transition temperature of 125 K among the homologous series of Tl2Ba2Can-1CunO2n+4. The direct information on the Cu ion site at the atomic level is important for elucidating the superconductivity mechanism. The local bond properties of Tl2Ba2Ca2Cu3O10 were studied using the average band-gap model. The calculated results show that the covalency of Cu(1)-O bond is 0.561, and the average covalency of Cu(2)-O is 0.296. M(o)ssbauer isomer shifts of 57Fe in Tl2Ba2Ca2Cu3O10 were calculated using the chemical surrounding factor, defined by covalency and electronic polarizability. It is verified that for lower doping, Fe substitute the Cu at the Cu (1) site in forms of Fe3+ and Fe4+; for higher doping, Fe3+ and Fe4+ ion occupies Cu(1) and Cu(2) site respectively.The studies show that the determination of the correspondence between spectrum components and actual copper sites occupied by M(o)ssbauer nucleus was made easier with the aid of the calculation results of the chemical bond parameters.     

超导相Tl2Ca3Ba2Cu4O12的制备与结构研究

我们已制备出Tl_2 Ca Ba_2 Cu_2O_8(2122)和Tl_2Ca_2 Ba_2 Cu_3 O_(10)(2223)两个纯相,并对它们的晶体结构和性质进行了研究。现在我们又制备出一种新的超导相,它的组成为Tl_2 Ca_3 Ba_2 Cu_4 O_(120(2324),并进一步研究了它的超导性质和晶体结构。     

Superconductivity in (Cu0.5Tl0.25Li0.25)Ba2Ca2Cu3−ySiyO10−δ samples

The (Cu_0.5Tl_0.25Li_0.25)Ba₂Ca₂Cu_3?ySi_yO_10?δ (y = 0, 0.25 0.5, 0.75, 1.0, 1.25) superconductor samples have been prepared by solid-state reaction method. The critical temperature and as well as the magnitude of diamagnetism is increased up to Si concentration y = 1.0, however, from the doping level y = 1.25 a decrease in the critical temperature along with the vanishing of the diamagnetism was observed. The carrier’s in the conducting CuO₂/SiO₂ planes were optimized by carrying out post-annealing in oxygen and an increase in the critical temperature was observed in all Si doped samples. The doping efficiency of Cu_0.5Tl_0.5Ba₂O_4?δ charge reservoir layer in (Cu_0.5Tl_0.25Li_0.25)Ba₂Ca₂Cu_3?ySi_yO_10?δ (y = 0, 0.25 0.5, 0.75, 1.0, 1.25) samples is enhanced by doping Li⁺¹ ion; as alkali metals are known to easily loose their outer most electron which could be supplied to CuO₂/SiO₂ conducting planes and would suppress the anti-ferromagnetism in the inner conducting planes. The FTIR absorption measurements have provided an indirect evidence of Si substitution at in CuO₂ planes.     

Normal pressure synthesis of (Tl1−yCy)Ba2Ca3Cu4O12−δ superconductor

Single phase (Tl_1−yC_y)Ba₂Ca₃Cu₄O_12−δ (Tl_1−yC_y-1234) (y = 0, 0.25, 0.5 and 0.75) superconductor samples have been prepared by solid state reaction method. The FTIR absorption measurements have confirmed the substitution of carbon at thallium site in the charge reservoir layer, (Tl_1−yC_y)Ba₂O_4−δ. The electron micrographs of these samples have shown that the carbon substitution has improved the grain morphology of Tl_0.75C_0.25-1234 sample. The y = 0.25 was found to be the optimum carbon concentration to achieve higher superconducting transition temperature T_c[0] and improved grain morphology. The superconducting transition temperature of Tl_0.75C_0.25-1234 sample has been increased to 100 K whereas a decrease in the superconducting transition temperature of Tl_1−yC_y-1234 (y = 0.5 and 0.75) samples was observed. However, the magnitude of diamagnetism has been decreased in all the carbon substituted samples.     

La0.5R0.5Ba2Cu3O7,Pr0.5R0.5Ba2Cu3O7以及RBa2Cu3o7（R=稀土）的键共价性计

使用复杂晶体化学键理论计算了Ｌａ０．５Ｒ０．５Ｂａ２Ｃｕ３Ｏ７（Ｒ＝Ｐｒ,Ｎｄ,Ｓｍ,Ｅｕ,Ｇｄ,Ｄｙ,Ｙ,Ｈｏ,Ｅｒ,Ｔｍ,Ｙｂ,Ｌｕ）（Ｌａ－Ｒ１２３）,Ｐｒ０．５Ｒ０．５Ｂａ２Ｃｕ３Ｏ７（Ｒ＝Ｌａ,Ｎｄ,Ｓｍ,Ｅｕ,Ｇｄ,Ｄｙ,Ｈｏ,Ｙ,Ｅｒ,Ｔｍ,Ｙｂ,Ｌｕ）（Ｐｒ－Ｒ１２３）以及ＲＢａ２Ｃｕ３Ｏ７（Ｒ＝Ｌａ,Ｐｒ,Ｎｄ,Ｓｍ,Ｅｕ,Ｇｄ,Ｄｙ,Ｈｏ,Ｙ,Ｅｒ,Ｔｍ）（Ｒ１２３）中Ｃｕ－Ｏ键的键共价性,结果表明Ｐｒ－Ｒ１２３,Ｌａ－Ｒ１２３,以及Ｒ１２３都应具有超导性,而实验结果是Ｌａ０．５Ｐｒ０．５Ｂａ２Ｃｕ０７,Ｒ０．５,Ｐｒ０．５Ｂａ２Ｃｕ３Ｏ７（Ｒ＝Ｌａ,Ｎｄ,Ｓｍ,Ｅｕ,Ｇｄ）无超导性,产生这种矛盾的原因尚不明确,需要做进一步的研究。     

Thermodynamic properties and oxygen stoichiometry of Ba2Cu3O5 + δ

The thermodynamic properties and oxygen stoichiometry of Ba₂Cu₃O_{5 + δ} are studied by means of the electromotive force (EMF) with a fluoride electrolyte, dissolution calorimetry, and thermogravimetry. It is shown that the temperature dependence of the Gibbs energy of the formation of barium cuprate from simple oxides and oxygen in the temperature range of 860–1120 K can be described by the polynomial Δ_{f, ox} G ^°(Ba₂Cu₃O_{5 + δ}) ± 0.1 (kJ/mol) = ?291.78 + 1.127T ? 0.13207 TlnT (kJ/mol).     

YBa2Cu4O8/La2/3Ca1/3MnO3/YBa2Cu4O8异质结中的超导转变温度

采用对靶溅射技术制备了YBa2Cu4O8/La2/3Ca1/3MnO3/YBa2Cu4O8（Y-124/LCMO/Y-124）异质结, 研究了超导转变温度（TC）随LCMO层厚度（dL）的振荡行为. 当dL＞dLCR时, TC-dL曲线表现出清晰的非单调行为, 而金属-绝缘体转变温度（TMI）仅当dL＞dLCR时才能观测到. Y-124/LCMO/Y-124系统中所存在的这种对中间层的依赖关系, 显示了铁磁和超导耦合间强烈的相互作用.     

Ca2+和Mn2+共掺杂Ba1-xSrxTiO3固溶体的制备及其电学性能研究

(Ca, Mn)-codoped Ba1-xSrxTiO3 (BST) solid solution, i.e. Ba0.4Sr0.5Ca0.08Mn0.02TiO3, was successfully synthesized via sol-gel process. The product was characterized by TG-DTA thermal analyses, XRD, TEM.The effects of both curing temperature and applied voltage on the resistance, etc. were investigated. It showed that the structure of BST was unable to be changed even though it was codoped by Ca2+ and Mn2+. TEM photographs demonstrated the influence of curing temperature on the morphologies of the tested samples. The dependence of resistance on the curing temperature illustrated that (Ca, Mn)-codoped BST was capable of exhibiting the positive temperature coefficient (PTC) effect at low frequency; nevertheless,it might display the negative temperature coefficient (NTC) effect at other frequencies. The relationships between the resistance and applied voltage revealed that the resistance property of (Ca, Mn)-codoped BST appeared at low frequencies, but its property of capacitive reactance might present at high frequency. These findings mean that the electrical property of BST can be adjusted by codoping method. These phenomena can be explained by the grain boundary resistance effect, Heywang model and ion polarization theory.     

四极质谱法研究激光烧蚀Y1Ba2Cu3O7-δ产物的分布

采用空间和时间分辨的四极质谱法了３５５ｎｍ脉冲激光     

Ca对Cu/B/Ca/Al_2O_3结构及其催化醋酸仲丁酯加氢反应性能的影响

以γ-Al2O3为载体采用分步浸渍法制备了不同Ca O含量的Cu/B/Ca/Al2O3催化剂,并测试了其催化醋酸仲丁酯加氢制备仲丁醇的反应性能.Ca O含量对催化剂的结构、氧化还原性能、酸碱性和金属铜分散度的影响分别采用XRD、H2-TPR、XPS、NH3-TPD和N2O-H2氧化还原滴定实验进行分析.结果表明,适量氧化钙的引入对金属铜的分散度无明显影响,过量的氧化钙(20%)降低催化剂的比表面积,进而导致金属铜分散度的降低;但钙作为给电子助剂能够补偿电子从铜向氧化硼之间的迁移,提高催化剂的酯加氢活性.同时,氧化钙的引入能够有效消除Cu/B/Ca/Al2O3催化剂表面的强酸性位点并降低催化剂的酸量,减少醋酸仲丁酯加氢反应中酸催化副产物以及催化剂表面积碳的生成.     

Eu2+在M3La3(BO3)4(M=Ca,Sr,Ba)中的发光性质

本文研究了Eu²⁺离子在M_yAl_xBO_y+3/2(1+x)(M=Ca,Sr,Ba)基质中的发光性质及磷和卤素对发光的影响。 采用以H₂和N₂混合气体为还原气氛在高温下进行固相反应的方法合成了一系列磷光体。发现,在CaAl_xBO_2.5+3/2x基质中,当X在0.5～2的范围内时及在Sr_yAl₂BO_{4 6+}基质中,当y在2～6的范围时掺入的Eu³⁺不能被H₂还原为Eu²⁺。其他Eu²⁺激活的磷光体一般都产生f～d跃迁的宽带发射,发射峰的波长随着基质组成的不同可在400～600nm的区间的变化。     

La2／3Ca1／3MnO3／YBa2Cu4O8／La2／3Cal／3MnO3三层薄膜中的各向异性磁电阻

研究了La2/3Ca1/3MnO3(LCMO)／YBa2Cu4O8(YBCO)／LCMO三层薄膜中的各向异性磁电阻。LCMO单层膜和三层膜都表现出面内各向异性，磁电阻对θ(磁场方向和偏置电流方向的夹角)和Ф(磁场方向和薄膜表面的夹角)表现出正弦三角函数的依赖关系。在低场下，无论在面内还是面外都发现了正的磁电阻。     

Eu3+在Ba2TiSi2O8中的发光

红色荧光材料主要有(碱土)硫化物体系[1,2],(碱土)钛酸盐体系[3,4],氧化稀土体系[5],硅酸盐体系[6]以及其它氧化物体系如MO∶Eu~(3 )(M=Ca、Sr、Ba)[7],SrAl2O4∶Eu~(2 )[8]等。在这些体系中,主要以Eu3 做激活     

The oxygen potentials corresponding to the YBa2Cu3O6+x phase in the YBaCuO system

Phase relations in the vicinity of the YBa₂Cu₃O_6+x in the CuO-rich part of the YBaCuO system were studied by the equilibration and quenching technique. At 950°C, the system is characterized by the large number of solid four-phase combinations. The oxygen potential as a function of temperature for two four-phase combinations, i.e., YBa₂Cu₃O_6+x + BaCuO₂ + BaCu₂O₂ + Y₂BaCuO₅ and YBa₂Cu₃O_6+x + BaCu₂O₂ + Y₂BaCuO₅ + Cu₂O, were studied by means of solid state EMF measurements. At higher oxygen potentials the pair of YBa₂Cu₃O_6+x and Y₂BaCuO₅ is stable in contact with BaCuO₂. At lower oxygen pressures this pair coexists in equilibrium with BaCu₂O₂ or Cu₂O.     

The system YPO4Ca3(PO4)2Ca2P2O7

The ternary system YPO₄Ca₃(PO₄)₂Ca₂P₂O₇ has been investigated by differential thermal analysis, powder X-ray diffraction, and microscopy in reflected light. Its phase diagram and isothermal section at room temperature have been determined. The system contains only one double phosphate which is formed at the 1:1 molar ratio YPO₄:Ca₃(PO₄)₂, i.e., Ca₃Y(PO₄)₃.     

Ca2+、Ba2+对光敏热成像材料照相性能和稳定性的影响

以常用的硬脂酸银为银源,异位AgBr为光敏元以及亲水型PVA为粘合剂,分别考察了Ca2+和Ba2+对光敏热成像(PTG)材料照相性能以及老化稳定性的影响.实验结果表明:涂布前乳液中加入Ca2+或Ba2+后,PTG材料的感光度和灰雾均出现不同程度的降低,并且随着加入量的增加,感光度下降更快.另外,含有Ca2+或Ba2+的PTG材料随着老化时间的增加,其感光度和灰雾的变化趋势并不相同.     

Ca掺杂的Ba2Al2Si10N14O4:Eu2+荧光粉发光性能

通过固相反应制备了系列Ca掺杂的Ba2Al2Si10M14O4:Eu2+色荧光粉,发现当半径较大的Ba被Ca取代后导致了晶格的收缩,通过X射线衍射(XRD)测量和Unitcell软件计算发现Ca的最大掺杂量在20％.Ca掺人Eu0.4Ba1.6Al2Si10N14O4荧光粉后,可有效地提高光转换性能,并使激发光谱发生一定程度的红移和宽化,从而被近紫外宽波段光有效激发,与近紫外LED的发射光谱匹配.同时Ca的掺杂也使发射光谱发生了可控的红移,可以由520 nm的绿光红移至548 nm的黄光区域.进一步发现Eu2+的淬灭浓度随着20％ Ca的掺入而降低,这是由于Ca掺入导致的晶格收缩使Eu2+离子间距离减小.最后在CIE色度图中对不同Ca,Eu浓度的荧光粉的色坐标位置进行比较,发现可通过Ca,Eu浓度的变化在很大范围内调制荧光粉的发光性能.     

Analysis of the energetic heterogenity of HgBa2Ca2Cu3O8+δ surfaces: Q-TG and Q-DTG data

Energetic heterogeneity of adsorbents is conditioned by the differences in topology of adsorption centres, dispersion of pore sizes and other factors. This paper describes theoretical and experimental studies that demonstrate a method for estimation of the energetic heterogeneity of adsorbents by making use of the results from single thermogravimetry Q-TG and Q-DTG curves, recorded under quasi-equilibrium conditions, for preadsorbed liquid on a porous solid surface.This revised version was published online in November 2005 with corrections to the Cover Date.     

Gd—Ba—Cu氯氧化物新相

在探索高Tc超导材料的过程中,人们采用替换元素的方法,试图寻找新体系的高温超导体。例如用钇取代La-Ba-Cu-O体系中的镧,结果使新体系的Tc(ρ=0)由原体系的30K提高到90K;在Y-Ba-Cu-O体系中掺入适量的氯后,观察到155K的超导电性。在此,我们对Gd-Ba-Cu-O体系掺氯后的物相变化情况,用X射线粉末衍射和电