Sorption and diffusion of gases in a polyimide

Sorption and diffusion of gases (CO₂, N₂, and He) in a polyimide (PI2080) film were measured by using an apparatus which gives the sorption rate curves from the initial state to the equilibrium state. Nonlinear isotherms observed for CO₂ sorption were interpreted successfully in terms of the dual-mode model for sorption in glassy polymers. Linear isotherms observed for N₂ and He seemed to obey Henry's law. Two diffusion coefficients (D_I and D_E) were obtained using the short-time method and the long-time method for a Fickian diffusion model, together with the equilibrium solubility (C_e) from each experiment. The initial sorption rate curves agreed with the calculated curves using D_I, however near sorption equilibrium the curves are in accord with the calculated curves using D_E. These observations suggest that some relaxation process is superimposed on the diffusion process. The non-Fickian transport data were correlated successfully with a model that combines time-dependent diffusion and the Fickian model.     

Determination of Absolute Gas Adsorption Isotherms by Combined Calorimetric and Dielectric Measurements

A new method to determine absolute masses of gas adsorbed on the external and internal surfaces of a porous solid is proposed. It consists on a combination of calorimetric and dielectric measurements. These lead to the enthalpy and the dielectric polarization of the adsorbed phase from which by purely thermodynamic calculations the absolute mass adsorbed can be determined without using the so-called helium volume hypothesis nor any other equivalent assumption.As example adsorption of subcritical carbon dioxide (CO₂) on zeolite (Degussa DAY) at 298 K and pressures up to 0,4 MPa is considered. As expected data of absolute masses adsorbed are always somewhat larger than the corresponding Gibbs excess masses calculated from both volumetric and gravimetric measurements via the helium volume of the zeolite.     

Sorption of light gases in glassy poly(ethyl methacrylate)

Although gas sorption in glassy polymers is a well‐studied phenomenon, no general microscopical model is developed which is able to describe the gas sorption in a wide temperature range using only characteristics of polymer and gas molecule. In this work, sorption isotherms and desorption kinetics of O₂, Ar, and N₂ for glassy poly(ethyl methacrylate) have been measured in the temperature range from 160 to 308 K. To describe both the phenomena, the model is developed which postulates that, in the frozen structure of glassy polymer, any cavities between macromolecules are the sorption sites for small molecules. The cavities of small size can expand elastically to accommodate a gas molecule. The sorption sites are considered to be the potential wells and their depths are distributed according to Gaussian law. The concentration of sorption sites, their mean depth and depths dispersion, and the frequency of molecules oscillations in the sorption sites are the only parameters which determine both the gas transport and sorption. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 288–296     

Sorption of Benzene in CoAlPO4-5 Molecular Sieves

The sorption isotherms of benzene in CoAlPO₄-5 at temperatures of 323–399 K were measured by the gravimetric technique. The sorption capacity and isosteric heat were estimated and interpreted on the basis of the pore topologies of the molecular sieves. The isotherms followed the typical Type-I shape, and could be well fitted with Langmuir and Dubinin-Radushkevich equations. The initial heats of sorption at zero coverage could be well explained by the surface curvature model. The isosteric heats of sorption varied with the coverage, which may suggest a shift of molecular packing manner in the sorbed phase.     

Sorption and transport of water in nylon-6 films

Sorption and transport properties of water through films of Nylon-6 were obtained at 5, 23, and 40°C. Commercially available films were used and a Cahn electrobalance was employed for measuring the water uptake by the polymer samples. Values of the water sorption isotherms are accurately described by the Langmuir/Flory-Huggins dual-mode sorption model. At water activity values below 0.15, the volume fraction of water described by the Langmuir portion of the model was greater than the Flory-Huggins population. Solubility and diffusion coefficients of water, as well as the diffusion activation energy and enthalpy of dissolution of water for Nylon-6, were determined from the sorption experiments. Values obtained support the hypothesis of a bimodal water sorption mode, and the formation of water clusters. © 1994 John Wiley & Sons, Inc.     

Sorption and Diffusion of Propylene and Ethylene in Heterophasic Polypropylene Copolymers

Summary: Sorption experiments of ethylene and propylene in different polypropylene powder samples, both homopolymer and heterophasic copolymers with different rubber content, have been carried out in a high-pressure magnetic suspension balance at 10 bars pressure and 70 °C. The gross solubilities measured can be well correlated with the rubber content of the polymer samples. Solubility of ethylene and propylene in the rubber phase differ from solubility in the amorphous fraction of the homopolymer, especially the concentration ratio of propylene to ethylene differs significantly between rubber phase and amorphous fraction of the homopolymer. From the slope of monomer uptake, information on kinetics of mass-transfer can be gained. No significant differences were observed in terms of mass-transfer for ethylene and propylene. With increasing rubber content, effective diffusion coefficients increased slightly. By combined sorption studies with powder samples and compressed films, information about both effective diffusion coefficients and the effective length scale of diffusion could be gained. It could be shown, that the particle radius is not the characteristic length of diffusion in the studied powder samples. Mass transfer of nearly all samples could be described by a constant diffusion length of 120 to 130 µm, independently on particle size. This indicates that the effective scale of diffusion in polymer particles is in between microparticle and macroparticle scale used in classical particle modeling.     

Sorption and diffusion of water vapor in polyimide films

Sorption and diffusion of water vapor are investigated gravimetrically for polyimide films. The activity dependence of the solubility and diffusion coefficients, S and D, respectively, is classified under four types: (1) constant S and D type, (2) dual-mode sorption and transport type, (3) dual-mode type followed by a deviation due to a plasticization effect at high vapor activity, and (4) constant S and D type followed by a deviation due to water cluster formation at high activity. For the dual-mode type, the Henry's law component is much larger than the Langmuir component except at low activity, and therefore deviation in behavior from the first type is small. S is larger for polyimides with higher content of polar groups such as carbonyl, carboxyl, and sulfonyl. D is larger for polyimides with a higher fraction of free space, with some exceptions. The polyimide from 3,3′,4,4′-biphenyltetracarboxylic dianhydride and dimethyl-3,7-diaminodibenzothiophene-5, 5-dioxide belongs to the third type and displays both large S and large D. The polyimide from 2,2-bis(3,4-dicarboxyphenyl) hexafluoropropane dianhydride and 4,4′-oxydianiline belongs to the fourth type, and has the largest D but rather small S because of the hydrophobic C(CF₃)₂ groups. © 1992 John Wiley & Sons, Inc.     

Sorption of small molecules in various polycarbonates and Kapton-H

Pressure-composition isotherms were determined at 20°C for CO₂ in Kapton and various substituted polycarbonates and for H₂O, Ar, N₂, CH₄, and acetone in bisphenol-A-polycarbonate. The isotherms are described by two parameters an average free energy of sorption and a width of a Gaussian distribution of free sorption energies. Within the framework of a recent model these parameters can be calculated assuming an elastic distortion of the polymer caused by the incorporation of solute atoms in preexisting holes. By comparing experimental values with predictions of the model the experimental width of the free energy distribution is only 30% smaller than the theoretical one. Functional relationships are obeyed between the sorption parameters on the one hand and glass transition temperature, average hole volume, and molecular volume of the solute on the other hand. Deviations occur for larger molecules like acetone and ethylene which are attributed to a viscoelastic distortion of the polymer. Comparing free energies of solution for the rubbery and glassy state of the polymer reveals more negative values for the glassy polymers despite their extra elastic distortion energy. This discrepancy is overcome by taking into account that the occupied volume has to be re-formed in the case of the rubbery or liquid polymer. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 483–494, 1998     

Sorption of carbon dioxide in fluorinated poyimides

Sorption isotherms of CO₂ for ten fluorinated polyimides measured at 35°C and up to about 25 atm are analyzed according to the dual-mode sorption model. Sorption properties for these polyimides are compared with those for other glassy Polymers including unfluorinated polyimides. The glassy polymers with higher glass transition temperatures T_g tend to show greater CO₂ sorption. Introduction of a ? C (CF₃)₂? linkage into the repeat unit of the main chain increases the sorption by 20–80%. For glassy polymers, including the fluorinated and unfluorinated polyimides, the Langmuir affinity constant b and Henry's law solubility constant k_D are correlated with the content of functional (carbonyl or sulfonyl) groups [FG], and composite parameter reflecting the magnitude of both [FG] and free-space fraction V_F, respectively, with some exceptions. The Langmuir capacity constant C′_H is correlated with T_g, but there are two correlation lines; one for unfluorinated polyimides and a different one for other glassy polymers including fluorinated polyimides. The slope of the former group is smaller probably because of smaller differences in thermal probably because of smaller differences in thermal expansion coefficients in rubbery and glassy states. Most fluorinated polyimides show greater solubility of CO₂ than unfluorinated polyimides and other glassy polymers, because of their larger C′_H and k_D. © 1993 John Wiley & Sons, Inc.     

Sorption and transport of linear alkane hydrocarbons in biaxially oriented polyethylene terephthalate

Equilibrium sorption and uptake kinetics of n‐butane and n‐pentane in uniform, biaxially oriented, semicrystalline polyethylene terephthalate films were examined at 35 °C and for pressures ranging from 0 to approximately 76 cmHg. Sorption isotherms were well described by the dual‐mode sorption model. Sorption kinetics were described either by Fickian diffusion or a two‐stage model incorporating Fickian diffusion at short times and protracted polymer structural relaxation at long times. Diffusion coefficients increased with increasing penetrant concentration. n‐Butane solubility was lower than that of n‐pentane, consistent with the more condensable nature of n‐pentane. However, n‐butane diffusion coefficients were higher than those of n‐pentane. Infinite‐dilution, estimated amorphous phase diffusion and solubility coefficients were well correlated with penetrant critical volume and critical temperature, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 1160–1172, 2001     

Preparation of Arabinoxylan and its Sorption on Bacterial Cellulose During Cultivation

The sorption of arabinoxylan (AX) on bacterial cellulose was investigated by adding AX to the culture medium of Gluconacetobacter xylinus. The starting AX material was produced by alkaline extraction of oat spelts. To investigate the impact of varying AX quality, the residual lignin was reduced by ClO₂ bleaching. Furthermore, bleached and unbleached xylans were subjected to xylanase hydrolysis in order to produce fractions of varying molar mass. Of all samples only the water soluble fractions were used for sorption experiments. A reduced molar mass resulted in a lower sorption of AX to the cellulose, while the lignin content increased the sorption of AX on bacterial cellulose. The sorption of AX resulted in a reduction of bacterial cellulose crystallinity and cellulose Iα content. In combined treatments of AX with xyloglucan and β-glucan no synergistic effect of those polysaccharides on the AX sorption was found.     

Sorption and diffusion of water vapour on edible films

Two types of films consisting of sodium salt of carboxymethyl cellulose (NaCMC) and hydroxypropyl cellulose (HPC) as film forming materials and glycerin as plasticizer were prepared, characterized and their water vapour sorption properties were determined. The water sorption isotherms of the films were measured using a magnetic suspension balance. Results show that diffusion of water vapour in NaCMC based film is faster than that in HPC based films, due to the heterogeneous structure and larger pore dimensions of the NaCMC films.     

Sorption and diffusion of organic vapors in amorphous Teflon AF2400

Vapor sorption in amorphous Teflon AF2400 of various organic solutes was studied in a wide range of activity at 25 °C by means of the gravimetric technique. The sorption isotherms of hexane, toluene, and chloroform were shown to be concave to the pressure axis and are consistent with the dual mode sorption model (DMS). The parameters of the DMS model k_D and b reveal a linear correlation with squared critical temperature of solutes T. The third model parameter, the Langmuir sorption capacity C′_H decreases when the size of solutes (critical volume) increases. Sorption isotherms of methanol and ethanol were shown to be convex to the pressure axis and are consistent with cluster formation in this strongly hydrophobic polymer. Concentration‐dependent diffusion coefficients D were determined using a linear implicit difference scheme in analysis of sorption kinetics. It was shown that D values increase exponentially with concentration for all the solutes, except alcohols for which exponential reduction of D(C) was observed. The partitioning of the thermodynamic and mobility contributions in D indicated that the reduction of D values of alcohols is consistent with clustering phenomena in AF2400. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 832–844, 2006     

Error Levels of Different Methods of Evaluation of TG Measurements

It follows from an analysis of the error levels of TG evaluation methods that it is a conceptual error to disregard the analogies of mass, energy and momentum streams of subordinate partial processes. This error is bypassed by means of the introduced method of dimensionless analysis and by determining the characteristic, constants-like data of thermal processes by using the measured data directly. These methods are very suitable for increasing the consistency of the calculated results by seeking for similarity, even in comparisons of measurements made under very different conditions and for emphasizing the differences too, quantitatively. With this new interpretation of TG processes, the idea of the kinetic compensation effect becomes only a consequence of the discussed conceptual error. This revised version was published online in August 2006 with corrections to the Cover Date.     

蒙脱土和高岭土对Pb2+的吸附

选择带结构负电荷的蒙脱土和带微量结构负电荷的高岭土,研究了其对Pb2+的吸附性能,并探讨了吸附机理。 研究表明,蒙脱土和高岭土吸附Pb2+的动力学曲线符合准二级动力学方程,吸附等温线符合Langmuir方程。 Pb2+同时以内层络合和外层配合形式吸附,其相对量与pH值有关。 在pH值小于4和大于8的范围内,以内层配合物为主;而pH值在4～8范围内外层配合物比例增大。 Pb2+能进入蒙脱土的层间,而不能进入高岭土的层间;部分Pb2+可进入黏土颗粒的微孔中被固定。 蒙脱土对Pb2+的吸附能力和饱和吸附量明显高于高岭土。     

Sorption and Desorption of Inclusion Compound Guests Different Types of Inclusion Compounds

The guests present in inclusion compounds participate in bonding with the hosts. The conditions for the sorption and desorption of the guests are decisive for the properties of the inclusion compounds. They are surveyed for many types of inclusion compounds. This revised version was published online in August 2006 with corrections to the Cover Date.     

Advances in Modeling Sorption and Diffusion of Moisture in Porous Reactive Materials

Water‐vapor‐uptake experiments were performed on a silica‐filled poly(dimethylsiloxane) (PDMS) network and modeled by using two different approaches. The data was modeled by using established methods and the model parameters were used to predict moisture uptake in a sample. The predictions are reasonably good, but not outstanding; many of the shortcomings of the modeling are discussed. A high‐fidelity modeling approach is derived and used to improve the modeling of moisture uptake and diffusion. Our modeling approach captures the physics and kinetics of diffusion and adsorption/desorption, simultaneously. It predicts uptake better than the established method; more importantly, it is also able to predict outgassing. The material used for these studies is a filled‐PDMS network; physical interpretations concerning the sorption and diffusion of moisture in this network are discussed.     

High Sorption and Selective Extraction of Actinides from Aqueous Solutions

The selective elimination of long-lived radioactive actinides from complicated solutions is crucial for pollution management of the environment. Knowledge about the species, structures and interaction mechanism of actinides at solid–water interfaces is helpful to understand and to evaluate physicochemical behavior in the natural environment. In this review, we summarize recent works about the sorption and interaction mechanism of actinides (using U, Np, Pu, Cm and Am as representative actinides) on natural clay minerals and man-made nanomaterials. The species and microstructures of actinides on solid particles were investigated by advanced spectroscopy techniques and computational theoretical calculations. The reduction and solidification of actinides on solid particles is the most effective way to immobilize actinides in the natural environment. The contents of this review may be helpful in evaluating the migration of actinides in near-field nuclear waste repositories and the mobilization properties of radionuclides in the environment.     

Sorption of tributyltin in seawater by municipal solid waste compost

The use of municipal solid waste (MSW) compost as a sorbent for tributyltin (TBT) in seawater was investigated. TBT‐contaminated seawater, both artificially prepared and that collected from Msida Creek yacht marina (Malta), was allowed to percolate through untreated and water‐washed columns of compost and then analysed for organotins using gas chromatography‐flame photometric detection. About 90% of dissolved TBT ranging in concentration from about 800 to 8000 ng_Snl^?1 was sorbed by treating 500 ml solutions with 100 g untreated compost. On the other hand, no detectable breakthrough of TBT was observed from compost that had previously been washed by water to remove soluble organic matter. Breakthrough of TBT from unwashed compost is thought to be due to formation of complexes between the soluble organic matter in compost and aquated TBT, which renders the organotin more hydrophilic. The use of washed MSW compost as sorbent for the purification of TBT‐contaminated waters generated in large quantity during hull‐cleaning activities in drydocks is suggested as a mitigatory measure against the impact of TBT on the coastal marine environment. Copyright © 2001 John Wiley & Sons, Ltd.     

Influence of the Synthesis pH on Sorption Behavior of Mesoporous MCM-41 for Toxic Metal Ions

Two samples of mesoporous MCM‐41 have been prepared in acidic and basic conditions with cetyltrimethylammonium bromide (CTAB) as template and characterized by powder X‐ray diffraction and N₂ adsorption‐desorption measurement to confirm the ordered mesoporous structure. Sorption of 21 toxic metal ions on these sorbents has been studied and discussed. The results show that distribution coefficient of Ba(II), Fe(III), Th(IV) on the synthesized MCM‐41 in basic condition and Cu(II), Pb(II), Zr(IV) on the synthesized MCM‐41 in acidic condition has been enhanced.