硅衬底GaN基LED薄膜芯片的应力调制

将Si衬底GaN基LED外延薄膜经晶圆键合、去硅衬底等工艺制作成垂直结构GaN基LED薄膜芯片,并对其进行不同温度的连续退火,通过高分辨X射线衍射(HRXRD)研究了连续退火过程中GaN薄膜芯片的应力变化。研究发现:垂直结构LED薄膜芯片在160~180℃下退火应力释放明显,200℃时应力释放充分,GaN的晶格常数接近标准值。继续升温应力不再发生明显变化,GaN薄膜的晶格常数只在标准晶格常数值附近波动。扫描电子显微镜给出的bonding层中Ag-In合金情况很好地解释了薄膜芯片应力的变化。     

Si衬底GaN基LED外延薄膜转移至金属基板的应力变化

采用电镀金属基板及湿法腐蚀衬底的方法将硅衬底上外延生长的GaNMQWLED薄膜转移至不同结构的金属基板,通过高分辨X射线衍射(HRXRD)和光致发光(PL)研究了转移的GaN薄膜应力变化。研究发现:(1)转移至铜基板、铬基板、铜/镍/铜叠层基板等三种基板的GaN薄膜张应力均减小,其中转移至铬基板的GaN薄膜张应力最小。(2)随着铬基板中铬主体层厚度的增加,转移后的GaN薄膜应力不发生明显变化。     

Si衬底GaN基LED的结温特性

结温是发光二极管的重要参数之一,它对器件的内量子效率、输出功率、可靠性及LED的其他一些性能有很大的影响。首次报道Si衬底GaN基LED的结温特性。利用正向压降法测量Si衬底上GaN基LED的结温,通过与蓝宝石衬底上GaNLED的结温比较,发现Si衬底GaNLED有更低的结温,原因归结为Si有更好的导热性。同时也表明:用Si作GaNLED的衬底在大功率LED方面具有更大的应用潜力。     

垒温对硅衬底GaN基蓝光LED发光效率的影响

用MOCVD技术在硅衬底上生长了GaN基蓝光LED外延材料,研究了有源层多量子阱中垒的生长温度对发光效率的影响,获得了不同电流密度下外量子效率(EQE)随垒温的变化关系。结果表明,在860~915℃范围内,发光效率随着垒温的上升而上升。当垒温超过915℃后,发光效率大幅下降。这一EL特性与X光双晶衍射和二次离子质谱所获得的阱垒界面陡峭程度有明显的对应关系,界面越陡峭则发光效率越高。垒温过高使界面变差的原因归结为阱垒界面的原子扩散。垒温偏低使界面变差的原因归结为垒对前一个量子阱界面的修复作用和为后一个量子阱提供台阶流界面的能力偏弱。外延生长时的最佳垒温范围为895~915℃。     

Si(110)和Si(111)衬底上制备InGaN/GaN蓝光发光二极管

分别在Si(110)和Si(111)衬底上制备了In Ga N/Ga N多量子阱结构蓝光发光二极管(LED)器件.利用高分辨X射线衍射、原子力显微镜、室温拉曼光谱和变温光致发光谱对生长的LED结构进行了结构表征.结果表明,相对于Si(111)上生长LED样品,Si(110)上生长的LED结构晶体质量较好,样品中存在较小的张应力,具有较高的内量子效率.对制备的LED芯片进行光电特性分析测试表明,两种衬底上制备的LED芯片等效串联电阻相差不大,在大电流注入下内量子效率下降较小;但是,相比于Si(111)上制备LED芯片,Si(110)上LED芯片具有较小的开启电压和更优异的发光特性.对LED器件电致发光(EL)发光峰随驱动电流的变化研究发现,由于Si(110)衬底上LED结构中阱层和垒层存在较小的应力/应变而在器件中产生较弱的量子限制斯塔克效应,致使Si(110)上LED芯片EL发光峰随驱动电流的蓝移量更小.     

Si衬底GaN基蓝光LED老化性能

报道了芯片尺寸为500μm×500μm硅衬底GaN基蓝光LED在常温下经1000h加速老化后的电学和发光性能,其光功率随老化时间的变化分先升后降两个阶段;老化后的反向漏电流和正向小电压下的电流均有明显的增加;老化后器件的外量子效率(EQE)比老化前低;老化前后EQE衰减幅度在不同的注入电流下存在明显差异,衰减幅度最小处出现在发光效率最高时对应的电流密度区间。     

图形硅衬底GaN基发光二极管薄膜去除衬底及AlN缓冲层后单个图形内微区发光及 应力变化的研究

研究了图形硅衬底上外延生长的氮化镓(GaN)基发光二极管(LED)薄膜、去除硅衬底后的无损自由状态LED薄膜以及去除氮化铝(AlN)缓冲层后的自由状态LED薄膜单个图形内的微区光致发光(PL)性能, 用荧光显微镜与扫描电镜观测了去除AlN缓冲层前后LED薄膜断面弯曲状况的变化. 研究结果表明: 1)去除硅衬底后, 自由支撑的LED薄膜朝衬底方向呈柱面弯曲状态, 且相邻图形的柱面弯曲方向不一致, 当进一步去除AlN缓冲层后薄膜会由弯曲变为平整; 2)LED薄膜在去除硅衬底前后同一图形内不同位置的PL谱具有显著差异, 而当去除AlN缓冲层后不同位置的PL谱会基本趋于一致; LED薄膜每一位置的PL 谱在去除硅衬底后均出现明显红移, 进一步去除AlN缓冲层后PL谱出现程度不一的微小蓝移; 3)自由支撑的LED薄膜去除AlN缓冲层后, PL光强随激光激发密度变化的线性关系增强, 光衰减得到改善.     

硅衬底GaN基LED N极性n型欧姆接触研究

在Si衬底GaN基垂直结构LED的N极性n型面上,利用电子束蒸发的方法制作了Ti/Al电极,通过了I-V曲线研究了有无AlN缓冲层对这种芯片欧姆接触的影响.结果显示,去除AlN缓冲层后的N极性n型面与Ti/Al电极在500到600 ℃范围内退火才能形成欧姆接触.而保留AlN缓冲层的N极性n型面与Ti/Al电极未退火时就表现为较好的欧姆接触,比接触电阻率为2×10^-5 Ω·cm²,即使退火温度升高至600 ℃,也始终保持着欧姆接触特性.因此,AlN缓冲层的存在是Si衬底GaN基垂直结构LED获得高热稳定性n型欧姆接触的关键. 关键词： 硅衬底 N极性 AlN缓冲层 欧姆接触     

斜切蓝宝石衬底MOCVD生长GaN薄膜的透射电镜研究

利用MOCVD技术在斜切角度为0.3°的c面蓝宝石衬底上生长了非故意掺杂 GaN 薄膜, 并采用透射电子显微镜对材料的质量和材料内部缺陷进行了分析. 研究发现斜切蓝宝石衬底上外延的GaN材料中,位错在距离衬底0.8 μm附近大量湮灭, 同时位错扎堆出现.基于上述现象, 提出了斜切衬底上GaN材料中位错的湮灭机制, 解释了斜切衬底能够提高GaN晶体质量的原因.     

SiN钝化膜对Si衬底GaN基蓝光LED性能影响

利用等离子辅助化学气相沉积(PECVD)系统在垂直结构Si衬底GaN基蓝光LED芯片上生长了SiN钝化膜,并对长有钝化膜及未作钝化处理的LED在不同条件下进行了老化实验,首次研究了SiN钝化膜对垂直结构Si衬底GaN基蓝光LED可靠性的影响。实验发现:经过30mA、85℃、24h条件老化后,未作钝化处理的Si衬底GaN基蓝光LED的平均光衰为11.41%,而长有SiN钝化膜的LED平均光衰为6.06%,SiN钝化膜有效地改善了LED在各种老化条件下的光衰,另外,SiN钝化膜缓解了Si衬底GaN基蓝光LED老化过程中反向电压(Vr)的下降,但对老化后LED的抗静电击穿能力(ESD)没有明显的影响。     

The influence of SixNy interlayer on GaN film grown on Si(111) substrate

A method to drastically reduce dislocation density in a GaN film grown on an Si(111) substrate is newly developed. In this method, the Si_xN_y interlayer which is deposited on an AlN buffer layer in situ is introduced to grow the GaN film laterally. The crack-free GaN film with thickness over 1.7 micron is grown on an Si(111) substrate successfully. Synthesized GaN epilayer is characterized by X-ray diffraction (XRD), atomic force microscope (AFM), and Raman spectrum. The test results show that the GaN crystal reveals a wurtzite structure with the <0001> crystal orientation and the full width at half maximum of the X-ray diffraction curve in the (0002) plane is as low as 403 arcsec for the GaN film grown on the Si substrate with an Si_xN_y interlayer. In addition, Raman scattering is used to study the stress in the sample. The results indicate that the Si_xN_y interlayer can more effectively accommodate the strain energy. So the dislocation density can be reduced drastically, and the crystal quality of GaN film can be greatly improved by introducing Si_xN_y interlayer.     

Effects of the microstructure slab with pillars on light extraction of GaN light-emitting diode

The positive z direction relative light extraction efficiency of GaN light-emitting diodes with microstructure slab is calculated by three-dimensional finite-difference time-domain method, where the microstructure slab consists of a graphite lattice of pillars. The results show that the two-dimensional graphite-arranged pillars suppress light extraction. When there is a thick pillar in the middle of the pillars, the structure can enhance light extraction of the light-emitting diodes. The tower-like pillars, which are thin on the top of the pillars and thick on the bottom of the pillars, benefit the light extraction when the angle of the tower-like pillars is proper.     

激光诱导p-GaN掺杂对发光二极管性能改善的分析

采用激光诱导掺锌的方法提高了常规GaN基外延片p-GaN层的空穴浓度,并将它制备成小功率白光发光二极管(LED).对其光电性能做了详细的测量并进行了加速老化实验和分析.结果表明,与常规LED相比,经过激光诱导p-GaN层掺锌LED的光电性能获得了明显改善:正向工作电压VF从3.33V降到3.13V,串联电阻从30.27Ω降到20.27Ω,室温下衰退系数从1.68×10-4降到1.34×10-4,老化1600h后的反向漏电流从超过0.2μA降为不超过0.025μA,器件的预测寿命延长了41%.器件光电性能改善的主要原因是激光诱导掺锌使LED的p-型欧姆接触改善和热阻降低所致.     

Efficiency enhancement of an InGaN light-emitting diode with a p-AIGaN/GaN superlattice last quantum barrier

In this study, the efficiency droop of an InGaN light-emitting diode （LED） is reduced slgnlncanUy oy using a p-AlGaN/GaN superlattice last quantum barrier. The reduction in efficiency droop is mainly caused by the decrease of electron current leakage and the increase of hole injection efficiency, which is revealed by investigating the light currents, internal quantum efficiencies, energy band diagrams, carrier concentrations, carrier current densities, and radiative recombination efficiencies of three LED structures with the advanced physical model of semiconductor device （APSYS）.     

Efficiency enhancement of an InGaN light-emitting diode with a p-AlGaN/GaN superlattice last quantum barrier

In this study,the efficiency droop of an InGaN light-emitting diode(LED)is reduced significantly by using a pAlGaN/GaN superlattice last quantum barrier.The reduction in efficiency droop is mainly caused by the decrease of electron current leakage and the increase of hole injection efficiency,which is revealed by investigating the light currents,internal quantum efficiencies,energy band diagrams,carrier concentrations,carrier current densities,and radiative recombination efficiencies of three LED structures with the advanced physical model of semiconductor device(APSYS).     

Morphological properties of AlN and GaN grown by MOVPE on porous Si(111) and Si(111) substrates

Metal Organic Vapour Phase Epitaxy (MOVPE) of AlN and GaN layers at a temperature of 1080 C were performed on porous Si(111) and Si(111) substrates. The thermal stability of porous silicon (PS) is studied versus growth time under AlN and GaN growth conditions. The surface morphology evolution of the annealed PS is revealed by scanning electron microscopy (SEM). Porous Si(111) with low porosity (40%) is more thermally stable than porous Si(100) with relatively high porosity (60%).AlN layers with various thicknesses were grown under the same conditions on the two substrates. Morphological properties of AlN were studied by atomic force microscopy (AFM) and compared taking into account the two different surfaces of the substrates. The two growth kinetics of AlN were found to be different due to the initial surface roughness of the PS substrate. The effect of AlN buffer morphology on the qualities of subsequent GaN layers is discussed. Morphological qualities of GaN layers grown on PS are improved compared to those obtained on porous Si(100) but are still less than those grown on Si substrate.     

Breakdown characteristics of AIGaN/GaN Schottky barrier diodes fabricated on a silicon substrate

In this work, the breakdown characteristics of AlGaN/GaN planar Schottky barrier diodes （SBDs） fabricated on the silicon substrate are investigated. The breakdown voltage （BV） of the SBDs first increases as a function of the anodeto-cathode distance and then tends to saturate at larger inter-electrode spacing. The saturation behavior of the BV is likely caused by the vertical breakdown through the intrinsic GaN buffer layer on silicon, which is supported by the post-breakdown primary leakage path analysis with the emission microscopy. Surface passivation and field plate termination are found effective to suppress the leakage current and enhance the BV of the SBDs. A high BV of 601 V is obtained with a low on-resistance of 3.15 mΩ·cm^2.     

Breakdown characteristics of AlGaN/GaN Schottky barrier diodes fabricated on a silicon substrate

In this work, the breakdown characteristics of AlGaN/GaN planar Schottky barrier diodes(SBDs) fabricated on the silicon substrate are investigated. The breakdown voltage(BV) of the SBDs first increases as a function of the anodeto-cathode distance and then tends to saturate at larger inter-electrode spacing. The saturation behavior of the BV is likely caused by the vertical breakdown through the intrinsic GaN buffer layer on silicon, which is supported by the postbreakdown primary leakage path analysis with the emission microscopy. Surface passivation and field plate termination are found effective to suppress the leakage current and enhance the BV of the SBDs. A high BV of 601 V is obtained with a low on-resistance of 3.15 mΩ·cm2.     

GaN/In_xGa_(1-x)N型最后一个量子势垒对发光二极管内量子效率的影响

GaN/In_xGa_(1-x)N型最后一个量子势垒结构能有效提高发光二极管(LED)器件内量子效率,缓解LED效率随输入电流增大而衰减的问题.本文综述了该结构及其结构变化——In组分梯度递增以及渐变、GaN/In_xGa_(1-x)N界面极化率改变等对改善LED器件性能的影响及优势,归纳总结了不同结构的GaN/In_xGa_(1-x)N型最后一个量子垒的工作机理,阐明极化反转是该结构提高LED性能的根本原因.在综述该结构发展的基础之上,通过APSYS仿真计算,进一步探索和深入分析了该结构中In_xGa_(1-x)N层的In组分及其厚度变化对LED内量子效率的影响.结果表明:In组分的增加有助于在GaN/In_xGa_(1-x)N界面产生更多的极化负电荷,增加GaN以及电子阻挡层处导带势垒高度,减少电子泄漏,从而提高LED的内量子效率;但GaN/In_xGa_(1-x)N型最后一个量子势垒中In_xGa_(1-x)N及GaN层厚度的变化由于会同时引起势垒高度和隧穿效应的改变,因而In_xGa_(1-x)N和GaN层的厚度存在一个最佳比值以实现最大化的减小漏电子,提高内量子效率.     

掺杂GaN间隔层对双波长发光二极管光谱调控作用的研究

采用软件理论分析的方法对p型及n型掺杂的GaN间隔层在InGaN/GaN多量子阱双波长发光二极管中对光谱调控作用进行模拟分析.分析结果表明,掺杂的GaN间隔层的引入,可以有效地控制各阱中的电子或空穴浓度,很好地解决了双波长发光二极管中两种阱发光强度不均的问题,并且通过控制阻挡层的厚度,可以调控两种阱中的载流子浓度,从而调控发光峰的相对强度.这些可以归因于掺杂GaN间隔层对电子或空穴的阻挡作用. 关键词： GaN 间隔层 数值模拟 双波长发光二极管