Strengthening of liquid crystalline polymer by functionalized carbon nanotubes through interfacial interaction and homogeneous dispersion

Multiwalled carbon nanotubes (MWCNTs) were functionalized with two types of chemical moieties (i.e. carboxylic, ? COOH and hydroxyl benzoic acid groups, ‐HBA) on their sidewalls in order to improve their interaction with a liquid crystalline polymer (LCP) and dispersion in LCP. We have investigated the rheological, mechanical, dynamic mechanical, and thermal properties in detail with variation of HBA‐functionalized MWCNTs in the LCP matrix. Effect of the dispersion state of the functionalized MWCNTs in the LCP matrix on the rheological behavior was also studied. The composites containing HBA‐functionalized MWCNTs showed higher complex viscosity, storage, and loss modulus than the composites with the same loading of raw MWCNTs and MWCNT‐COOH. It was suggested that the HBA‐functionalized MWCNTs exhibited a better dispersion in the polymer matrix and formed stronger CNT‐polymer interaction in the composites than the raw MWCNTs and MWCNT‐COOH, which was also confirmed by FESEM and FTIR studies. As a result, the overall mechanical performance of the HBA‐MWCNT‐LCP composites could be improved significantly. For example, the addition of 4 wt% HBA‐MWCNT to LCP resulted in the considerable improvements in the tensile strength and modulus of LCP (by 66 and 90%, respectively). Copyright © 2010 John Wiley & Sons, Ltd.     

End-cap effects on vibrational structures of finite-length carbon nanotubes

Vibrational structures of C60-related finite-length nanotubes, C(40+20n) and C(42+18n) (1 < or = n < or = 4), in which n is, respectively, the number of cyclic cis- and trans-polyene chains inserted between fullerene hemispheres, are analyzed from density functional theory (DFT) calculations. To illuminate the end-cap effects on their vibrational structures, the corresponding tubes terminated by H atoms C(20n)H20 and C(18n)H18 (1 < or = n < or = 5) are also investigated. DFT calculations show a broad range of vibrational frequencies for the finite-size nanotubes: high-frequency modes (1100-1600 cm(-1)) containing oscillations along tangential directions (tangential modes), medium-frequency modes (700-850 cm(-1)) whose oscillations are located on the edges or end caps, and low-frequency modes (300-600 cm(-1)) involving oscillations along the radial directions (radial modes). Broadening of the calculated frequencies is due to the number of nodes in the standing waves of normal modes in the finite-size tubes. In the capped tubes, calculated vibrational frequencies are insensitive to the number of chains (n), whereas in the uncapped tubes, most vibrational frequencies change significantly with an increase in tube length. The discrepancy in the size dependency is reasonably understood by their C-C bonding networks; the capped tubes have similar bond-length alternation patterns within the polyene chains irrespective of n, whereas the uncapped tubes have various bond-deformation patterns. Thus, DFT calculations illuminate that the edge effects have strong impacts on the vibrational frequencies in the finite-size nanotubes.     

椅型碳纳米管电子结构与长度效应

采用PM3方法对含帽结构的三种(5,5)椅型有限长碳纳米管的构型和电子结构进行了系统研究，结果表明，随着管长度的增加，除了最高占据轨道(HOMO)和最低空轨道(LUMO)之间的能隙(Eg)出现周期性的变化外，纳米管端“表面”(管的末端和管帽)构型也出现周期振荡现象，通过研究同种类型纳米管三组不同的长度效应，发现属于同一组的纳米管具有相似的构型和电子结构变化规律，此外，研究表明纳米管帽的尺寸效应可以看成为一定长度管壁的简单延伸，揭示了含帽与不含帽纳米管电子结构之间的相似性。本文还对处在管末端以及管帽上的表面态及其化学反应性进行了探讨。     

Electrospinning of poly(vinylidene fluoride)/dimethylformamide solutions with carbon nanotubes

For conductive carbon nanotube (CN)/polymer composite fibers to be obtained, CNs were incorporated into poly(vinylidene fluoride) (PVDF) in dimethylformamide (DMF) solutions and electrospun to form CN/PVDF fiber mats. The thinnest fiber was 70 nm thick. The percolation threshold for the insulator‐to‐conductor transition was 0.003 wt % CN for CN/PVDF/DMF solutions, 0.015 wt % CN for CN/PVDF spin‐coated films, and 0.04 wt % CN for CN/PVDF electrospun fiber mats. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1572–1577, 2003     

Doping of polyvinylidene difluoride with cobalt nitrate: Structural,electrical, and magnetic properties

Polyvinylidene difluoride (PVDF) doped with a few percentage of cobalt nitrate hexahydrate induces transition into the ferroelectric β‐phase. Infrared spectra show peaks indicative of β‐phase PVDF at 1277 cm^?1 and loss of the α‐phase peak at 790 cm^?1 while polarization measurements show loops consistent with relaxor ferroelectric behavior. Electronic spectroscopy shows that the Co²⁺ ion is in a six‐coordinate environment, and this is confirmed by magnetic susceptibility. Thermal measurements show that the PVDF melts near 155 °C, depending on the Co²⁺ content, and that there are several other thermal features that are associated with the hydrated cobalt nitrate. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Glycine interaction with carbon nanotubes: an ab initio study

The interaction of the glycine radical on the side walls of both armchair and zigzag single walled carbon nanotubes is investigated by density functional theory. It is found that the interaction potential of the N-centered glycine radical with the tubes has a minimum of 16.9 (armchair) and 20.2 (zigzag) kcal/mol with respect to the dissociation products. In contrast, the C-centered radical, which is 22.7 kcal/mol lower in energy than the N-centered radical, does not form stable complexes with both types of carbon nanotubes.     

Photoemission and absorption spectroscopy of carbon nanotube interfacial interaction

Element-specific techniques including near edge X-ray absorption fine structure, extended X-ray absorption fine structure and X-ray photoemission spectroscopy for the characterization of the carbon nanotube interfacial interactions are reviewed. These techniques involve soft and hard X-rays from the laboratory-based and synchrotron radiation facilities. The results provided information of how the nano-particles of catalysts are involved in the initial stage of nanotube growth, the nanotube chemical properties after purification, functionalization, doping and composite formation.     

Improved interfacial properties of PI composites through graphene oxide and carbon nanotubes on carbon fiber surface

Carbon nanotubes (CNTs) have been identified as excellent nanoreinforcements for carbon fiber (CF)–reinforced polymers regarding a wide range of engineering applications. The outstanding properties of CNTs, such as their large surface area, high mechanical strength, and low manufacturing cost bring them to be distinguished nanoreinforcements for carbon fiber–reinforced polymers to form multifunctional and multiscale composites. Electrophoretic deposition of graphene oxide for CNTs onto the CF surface was conducted. The presence of graphene oxide–CNTs may effectively increase both the roughness and wettability of the CF surface, resulting in an improvement to the interfacial bonding strength between the CF and the polyimide (PI).     

Calorimetric investigation of the interaction of carbon nanotubes with polystyrene

A simple, scalable procedure that does not require covalent modification of the filler or specialized high shear mixers is described for preparing well‐dispersed carbon nanotube composites. Excellent particle dispersions of multiple‐walled carbon nanotubes (NTs) and carbon black (CB) in polystyrene (PS) are obtained by coating the particles with a <2‐nm layer of PS adsorbed from dilute solution, prior to incorporation in the composite. Improved mechanical properties of composites containing coated particles, especially NT, are demonstrated by dynamic mechanical analysis at low frequency and low amplitude. Formation of a partially immobilized region of polymer surrounding the particles is quantified using flow microcalorimetry with ethyl acetate or methyl ethyl ketone vapor to measure the increase in solvation enthalpy in this region. This calorimetric method is applied to both composites and compacted powder mixtures of NT or CB with PS. The response of integral heat of vapor sorption as a function of particle loading in powder mixtures is similar to percolation curves reported for mechanical and electrical properties of composites. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1821–1834, 2006     

Selective host-guest interaction of single-walled carbon nanotubes with functionalised fullerenes

Exohedrally functionalised fullerenes have been inserted in single-walled carbon nanotubes (SWNTs) with the aid of supercritical carbon dioxide to form peapods; C(61)(COOEt)(2) are encapsulated in SWNTs in high yield, whereas C(61)(COOH)(2) aggregate via hydrogen bonding to form a supramolecular complex, which sterically hinders encapsulation and causes it to adhere to the exterior surface of the SWNTs.     

Infrared spectroscopic study of O2 interaction with carbon nanotubes

Infrared reflection-absorption spectroscopic measurements have been performed on single-wall carbon nanotubes (SWNTs), cleaned by heating to approximately 500 degrees C in vacuo, during exposure to pure 16O2 or 18O2 at room temperature and at pressures of up to approximately 630 Torr. No vibrational signature of any form of adsorbed O is detected. However, structure is seen which is very similar to that observed for the adsorption of atomic H or D and which indicates changes in the SWNT vibrational spectrum. The close similarity between the spectra for atomic H and D, on one hand, and O2 on the other is an unexpected result. Changes are also noted in the broad background extending throughout the mid-IR which arises from the Drude contribution to the reflectance. All these effects increase with O2 exposure and are essentially irreversible upon evacuation of the gas. The results are consistent with other data indicating that O2 interacts only weakly with, and does not chemisorb on, pristine regions of the SWNT under these conditions. The small and irreversible effects seen upon O2 exposure are interpreted in terms of enhanced chemisorption, at or near defective regions of the SWNT wall, which saturates at a low O coverage.     

Catalytic conversion of propan-2-ol and butan-2-ol on carbon nanotubes with different carbon structures

1. Download : Download high-res image (163KB)
2. Download : Download full-size image

     

Self-organization of supramolecular microporous structures based on carbon nanotubes and benzene

The molecular dynamic has been used to study the self-organization of carbon nanotubes into an array in the presence of coordinating molecules. Methane adsorption on model systems has been calculated. It has been shown that secondary porosity formed by the nanotubes makes it possible to accumulate methane at the level of the best commercial adsorbents. Supramolecular systems have been synthesized on the basis of carbon nanotubes and benzene molecules used as coordinators according to a scheme realized in the numerical simulation. The specific adsorption of nitrogen at 293 K on the obtained supramolecular structure has been shown to increase by more than tenfold as compared with that on initial nanotubes.     

Theoretical studies on structures and aromaticity of finite-length armchair carbon nanotubes

[structure: see text] Depending on the exact length of the tube, the chemical structure of finite-length armchair [n,n] single-wall carbon nanotube (n = 5 and 6) falls into three different classes that may be referred to as Kekulé, incomplete Clar, and complete Clar networks. The C-C bond lengths, nucleus-independent chemical shift analysis, and orbital energies suggest that the chemical reactivities of the finite-length tube change periodically as the tube length is elongated by one-by-one layering of cyclic carbon array.     

Electrodes modified with iron porphyrin and carbon nanotubes: application to CO2 reduction and mechanism of synergistic electrocatalysis

Electrodes modified with iron porphyrin and carbon nanotubes (FeP–CNTs) were prepared and used for CO₂ electroreduction. The adsorption of iron porphyrin onto the multiwalled carbon nanotubes was characterized by scanning electron microscopy and ultraviolet and visible spectroscopy. The electrochemical properties of the modified electrodes for CO₂ reduction were investigated by cyclic voltammetry and CO₂ electrolysis. The FeP–CNT electrodes exhibited less negative cathode potential and higher reaction rate than the electrodes modified only with iron porphyrin or carbon nanotubes. A mechanism of the synergistic catalysis was proposed and studied by electrochemical impedance spectroscopy and electron paramagnetic resonance. The direct electron transfer between iron porphyrin and carbon nanotubes was examined. The current study shed light on the mechanism of synergistic catalysis between CNTs and metalloporphyrin, and the iron porphyrin–CNT-modified electrodes showed great potential in the efficient CO₂ electroreduction.     

Electrochemical investigation of a glassy carbon electrode modified with carbon nanotubes decorated with (poly)crystalline gold

Multiwalled carbon nanotubes with nanosized sputtered gold were used to modify a glassy carbon electrode (GCE). The substrate was characterized by scanning electron microscopy (SEM), X-ray diffraction, cyclic voltammetry and amperometry. SEM micrographs indicated an uniform coverage of the carbon nanotubes with nanosized (poly)crystalline gold. Cyclic voltammetry reveals that peak separation of the unmodified GCE in the presence of 1?mM ferricyanide is 131?mV, but 60?mV only for the modified GCE. In addition, the oxidation of NADH (1?mmol?L^?1 solution) begins at negative potentials (around ?100?mV vs. Ag/AgCl), and the anodic peak potential (corresponding to the irreversible oxidation of NADH) is found at +94?mV. The effect of pH on the electrocatalytic activity was studied in the range from 5.4 to 8.0. The relationship between the anodic peak potential and the pH indicated a variation of ?33.5?mV/pH which is in agreement with a two-electron and one-proton reaction mechanism. Amperometry, performed at either ?50 or +50?mV vs. an Ag/AgCl reference electrode, indicates that the modified electrode is a viable amperometric sensor for NADH. At a working potential of +50?mV, the response to NADH is linear in the concentration range from 1 to 100???mol?L^?1, with an RSD of 6% (n?=?4).

Directed assembly of carbon nanotubes at liquid-liquid interfaces: nanoscale conveyors for interfacial biocatalysis

We report that single-walled carbon nanotubes (SWNTs) can be directed to aqueous-organic interfaces with the aid of surfactants. This phenomenon can also be used to transport enzymes to the interface to effect biphasic biotransformations. Consequently, SWNT-enzyme conjugates enhance the rate of catalysis by up to 3 orders of magnitude relative to the rates obtained with native enzymes in similar biphasic systems. Furthermore, we demonstrate that this concept can be extended to other nanomaterials and other enzymes, thereby providing a general strategy for efficient interfacial biocatalysis. The ability to direct the assembly of nanotubes at the interface also provides an attractive route to organizing these nanomaterials into 2D architectures.     

Temperature and size effects on diffusion in carbon nanotubes

We study the self-diffusion of simple gases inside single-walled carbon nanotubes at the zero-loading limit by molecular dynamics simulations. The host-framework flexibility influence is taken into account. In particular, we study the influences of nanotube size and temperature. For the carbon-nanotube radius-dependent self-diffusivities, a maximum is observed, which resembles the so-called levitation effect. This occurs for pores having a radius comparable to the position of the interaction-energy minimum. Surprisingly, the temperature influence is not uniform throughout different pore sizes. Diffusivities are expected to increase with temperature. This effect is observed for carbon nanotubes distinctly larger than the guest molecules. Remarkably, for smaller pores, the self-diffusivities decrease with increasing temperature or exhibit a maximum in the temperature dependence. This effect is caused by competing influences of collision frequency and temperature.     

Tailoring electronic structures of carbon nanotubes by solvent with electron-donating and -withdrawing groups

Various electron-donating and -withdrawing groups in aromatic and aliphatic backbones of solvent have been introduced to tailor the electronic structures of single-walled carbon nanotubes (SWCNTs). In the case of solvent with a withdrawing group, electrons were extracted mainly from metallic SWCNTs, whereas small charge transfer was also observed in semiconducting SWCNTs. On the other hand, in the case of solvent with a donating group, electrons were donated to both metallic and semiconducting SWCNTs. This effect was less prominent in solvent with an aliphatic backbone than that with an aromatic backbone. The strong correlation between the sheet resistance and electronic structures of nanotubes is further discussed in conjunction with a modulation of Schottky barrier height.     

Separation of peptides on Empore thin-layer chromatography sheets and blotting onto polyvinylidene difluoride membranes with subsequent gas phase sequencing.

Methods for the separation of peptides on a new type of thin-layer chromatography (TLC) sheet and blotting onto polyvinylidene difluoride (PVDF) membranes with subsequent gas phase sequencing are described. For validation, the A and B chain of insulin were chromatographed on Empore TLC sheets and either extracted or blotted onto PVDF membranes. The advantages and disadvantages of thin-layer chromatography on Empore sheets versus high performance liquid chromatography (HPLC) are discussed, along with the possibility of combining the two methods. In addition, TLC was combined with electrophoresis (fingerprinting) for the separation of complex peptide mixtures. Blotting from TLC sheets onto PVDF membranes was performed in two ways: contact diffusion and electrophoretic transfer. In our experiments electroblotting was more effective. Amino acid sequence determination of the B chain of insulin was possible both after extraction from the TLC sheet and after blotting onto PVDF membranes. In the former case, liquid phase sequencing and, in the latter case, gas phase sequencing was performed. The possibility to blot from TLC sheets onto membranes, e.g. PVDF, may prove useful in many fields, for example in biochemistry, and in molecular and cell biology.