Ring opening polymerization of epoxides with urea‐derivatives of 4‐aminopyridine as thermally latent anionic initiator

In this study, a series of urea‐derivatives of 4‐aminopyridine (4AP) were evaluated as thermally latent initiators for the anionic ring‐opening polymerization of diglycidyl ether of bisphenol A (DGEBA). The urea‐derivatives were synthesized by the reactions of 4AP with the corresponding iso(thio)cyanates (phenyl isocyanate, tert‐butyl isocyanate, methylene diphenyl diisocyanate, and phenyl isothiocyanate). The ability of the urea‐derivatives as latent initiators was investigated with differential scanning calorimetry (DSC): Upon heating formulations comprised of DGEBA and the urea‐derivatives in a heating rate at 10 °C/min, the resulting DSC profiles indicated exothermic peaks to confirm that DGEBA underwent the polymerization efficiently. The corresponding DSC‐peak top temperatures (T_{peak top}) was higher than that observed for the formulation comprised of DGEBA and pristine 4AP, to clarify that the urea are useful initiators with thermal latency. A possible mechanism for the initiation step involves the thermal dissociation of the urea into 4AP and the corresponding isocyanates. 4AP thus generated readily initiated the ring‐opening polymerization of epoxide. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2518–2522     

Promoting effect of thiophenols on the ring‐opening polymerization of 1,3‐benzoxazine

Thiophenol and p‐nitrothiophenol were evaluated as promoters for the ring opening polymerization of benzoxazine. The ring‐opening polymerization of p‐cresol type monofunctional N‐phenyl benzoxazine 1a with 10 mol % of thiophenols proceeded at 150 °C, leading to the high conversion of 1a more than 95% within 5 h, whereas the polymerization of 1a without thiophenols did not proceed under the same conditions. The promotion effect of the thiophenols on curing of bisphenol‐A type N‐phenyl benzoxazine 1b was also investigated. In the differential scanning calorimetric (DSC) analysis of the polymerization of 1b at 150 °C without using any promoters, an exothermic peak attributable to the ring‐opening reaction of benzoxazine was observed after 8 h. In contrast, in the DSC analysis of the polymerization of 1b with addition 20 mol % of p‐nitrothiophenol, an exothermic peak was observed within 2 h, to clarify the significant promoting effect of p‐nitrothiophenol. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2523–2527     

Promoting effects of urethane derivatives of phenols on the ring‐opening polymerization of 1,3‐benzoxazines

For the purpose of reducing the induction period of the ring‐opening polymerization of N‐methyl‐1,3‐benzoxazines, several urethanes were examined as promoters. The examined promoters 3a – d were the adducts of resorcinol and phenyl isocyanate, that of bisphenol A and phenyl isocyanate, that of resorcinol and butyl isocyanate, and that of 1,3‐propanediol and phenyl isocyanate, respectively. The aromatic urethanes 3a and 3b , which were adducts of the phenolic compounds and phenyl isocyanate, exhibited significant promoting effects. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Structure–initiator activity dependence of aminimides as thermally latent initiators in the polymerization of glycidyl phenyl ether

Novel aliphatic aminimides were synthesized from the corresponding carboxylic acid esters, 1,1‐dimethylhydrazine, and epoxides in 54–95% yields. Bulk polymerization of glycidyl phenyl ether (GPE) with 3 mol % of the aminimides was evaluated by DSC as a model process for curing of epoxy resin. All the aminimides showed no exothermic DSC peak below 120 °C but showed sharp exothermic peaks above 137 °C, indicating good thermal latency. Good relationships were observed between the calculated bond length from the carbonyl carbon to the α‐carbon of the aliphatic group (R C), DSC onset temperatures, and the thermal dissociation temperatures (T_d 's) of the aminimides. The aminimide with a longer R C bond length showed lower T_d and DSC onset temperature, that is, higher activity. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3428–3433, 2000     

Polybenzimidazoles tethered with N‐phenyl 1,2,4‐triazole units as polymer electrolytes for fuel cells

Polybenzimidazole (PBI) polymers tethered with N‐phenyl 1,2,4‐triazole (NPT) groups were prepared from a newly synthesized aromatic diacid, 3′‐(4‐phenyl‐4H‐1,2,4‐triazole‐3,5‐diyl) dibenzoic acid (PTDBA). The obtained polymers show superior thermal and chemical stability and good solubility in many aprotic solvents. The inherent viscosities of all polymers were around 1 dL/g. They exhibit high thermal stability with initial decomposition temperature ranging from 515 to 530 °C, high glass transition temperature ranging from 375 to 410 °C, and good mechanical properties with tensile stress in the range of 66–98 MPa and modulus 1897–2600 MPa. XRD analysis indicates that these polymers are amorphous in nature. Physicochemical properties such as water and phosphoric acid‐uptake, oxidative stability, and proton conductivity of membranes of these polymers have also been determined. The proton conductivity ranged from 4.7 × 10^?3 to 1.8 × 10^?2 S cm^?1 at 175 °C in dry conditions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2289–2303, 2009     

High refractive index materials: A structural property comparison of sulfide‐ and sulfoxide‐containing polyamides

High‐refractive‐index polyamides (PAs) are developed by incorporation of sulfide‐ or sulfoxide linkages and chlorine substituents. The PAs are synthesized through the polycondensation of two novel diamine monomers, 2,2′‐sulfide‐bis(4‐chloro‐1‐(4‐aminophenoxy) phenyl ether (3a) and 2,2′‐sulfoxide‐bis(4‐chloro‐1‐(4‐aminophenoxy) phenyl ether (3b), with various aromatic diacids (a–e). The ortho‐sulfide or sulfoxide units, pendant chlorine groups, and flexible ether linkages in the diamine monomers endowed the obtained PAs with excellent solubilities in organic solvents. The resulting PAs showed high thermal stability, with 10% weight loss temperatures exceeding 415 °C under nitrogen and 399 °C in air atmosphere. The combination of chlorine substituents, sulfide or sulfoxide linkages, and ortho‐catenated structures provided polymers with high transparency along with high refractive index values of up to 1.7401 at 632.8 nm and low birefringences (<0.0075). The structure–property relationships of the analogous PAs containing sulfide or sulfoxide linkages were also studied in detail by comparing the results. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2867–2877     

Synthesis and characterization of an adipic acid–derived epoxy resin

Adipic acid, a highly abundant chemical that can be produced from biomass, was used to prepare an aromatic‐free epoxy resin. Synthesis of the diglycidyl adipate was performed by a one‐step process using epichlorohydrin and by a two‐step process comprising allylation and epoxidation. The viscosity of diglycidyl adipate is 25 mPa·s, which is 99% lower than the diglycidyl ether of bisphenol A (DGEBA). The storage modulus at 25 °C for cured diglycidyl adipate and DGEBA is 2000 and 3200 MPa, respectively. The alpha transition temperature through peak of the loss modulus and the peak of tan(δ), are 77 °C and 90 °C, respectively. Low‐viscosity epoxy applications are discussed herein. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2625–2631     

Synthesis and characterization of novel soluble triphenylamine‐containing aromatic polyamides based on N,N′‐bis(4‐aminophenyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new triphenylamine‐containing aromatic diamine, N, N′‐bis(4‐aminophenyl)‐N, N′‐diphenyl‐1,4‐phenylenediamine, was prepared by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 4‐fluoronitrobenzene, followed by catalytic reduction. A series of novel aromatic polyamides with triphenylamine units were prepared from the diamine and various aromatic dicarboxylic acids or their diacid chlorides via the direct phosphorylation polycondensation or low‐temperature solution polycondensation. All the polyamides were amorphous and readily soluble in many organic solvents such as N, N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone. These polymers could be solution cast into transparent, tough, and flexible films with good mechanical properties. They had useful levels of thermal stability associated with relatively high glass‐transition temperatures (257–287 °C), 10% weight‐loss temperatures in excess of 550 °C, and char yields at 800 °C in nitrogen higher than 72%. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2810–2818, 2002     

Preparation and characterization of aromatic polyamides based on a bis(ether‐carboxylic acid) or a dietheramine extended from 1,1‐bis(4‐hydroxyphenyl)‐1‐phenylethane

Thermoplastic and organic‐soluble aromatic polyamides containing both bulky triphenylethane units and flexible ether linkages were prepared directly from 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐1‐phenylethane ( III ) with various aromatic diamines or from 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenylethane ( V ) with various aromatic dicarboxylic diacids via triphenyl phosphite and pyridine. These polyamides had inherent viscosities ranging from 0.71 to 1.77 dL/g. All the polymers easily were dissolved in aprotic polar solvents such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide, and some even could be dissolved in less polar solvents such as tetrahydrofuran. The flexible and tough films cast from the polymer solutions possessed tensile strengths of 89 to 104 MPa. The polyamides were thermally stable up to 460°C in air or nitrogen. Glass‐transition temperatures of these polyamides were observed in a range of 179 to 268°C via differential scanning calorimetry or thermomechanical analysis. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 247–260, 2000     

Synthesis and characterization of chiral poly(alkyl isocyanates) by coordination polymerization using a chiral half‐titanocene complex

A new chiral half‐titanocene complex, [CpTiCl₂(O‐(S)?2‐Bu)], is synthesized and characterized by ¹H and ¹³C NMR spectroscopy. This complex is employed for the coordination polymerization of n‐butyl and n‐hexyl‐ isocyanate leading to chiral polymers, as revealed by their CD spectra. Only the left‐handed helix is produced, due to the chiral (S)?2‐butoxy group, which is bound to the polymer chain end. The polymerization of 3‐(triethoxysilyl)propyl isocyanate produces less soluble polymers. On the other hand, phenyl isocyanate reacts slowly with the complex leading quantitatively and selectively to triphenyl isocyanurate. 2‐Ethylhexyl isocyanate is slowly and selectively cyclotrimerized in the presence of the half‐titanocene complex. However, a statistical copolymer of 2‐ethylhexyl isocyanate and hexyl isocyanate is produced. The reaction of benzyl isocyanate with the complex leads to a mixture of low molecular weight polymer and cyclotrimer. The polymers are characterized using SEC, NMR, and CD spectroscopy and their thermal properties are investigated by TGA/DSC analysis. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2141–2151     

Syntheses and properties of novel fluorinated polyamides based on a bis(ether‐carboxylic acid) or a bis(ether amine) extended from bis(4‐hydroxyphenyl)phenyl‐2,2,2‐trifluoroethane

Two series of novel fluorinated aromatic polyamides were prepared from 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane with various aromatic diamines or from 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane with various aromatic dicarboxylic acids with the phosphorylation polyamidation technique. These polyamides had inherent viscosities ranging from 0.51 to 1.54 dL/g that corresponded to weight‐average and number‐average molecular weights (by gel permeation chromatography) of 36,200–80,000 and 17,200–64,300, respectively. All polymers were highly soluble in aprotic polar solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide, and some could even be dissolved in less‐polar solvents like tetrahydrofuran. The flexible and tough films cast from the polymer solutions possessed tensile strengths of 76–94 MPa and initial moduli of 1.70–2.22 GPa. Glass‐transition temperatures (T_g's) and softening temperatures of these polyamides were observed in the range of 185–268 °C by differential scanning calorimetry or thermomechanical analysis. Decomposition temperatures (T_d's) for 10% weight loss all occurred above 500 °C in both nitrogen and air atmospheres. Almost all the fluorinated polyamides displayed relatively higher T_g and T_d values than the corresponding nonfluorinated analogues. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 420–431, 2003     

Acceleration effects of 1,5,7‐triazabicyclo[4.4.0]dec‐5‐ene with 2‐methylimidazole‐intercalated α‐zirconium phosphate as a latent thermal initiator in the reaction of glycidyl phenyl ether and hexahydro‐4‐methylphthalic anhydride

The catalytic effects of 1,5,7‐Triazabicyclo[4.4.0]dec‐5‐ene (TBD) with 2‐methylimidazole‐intercalated α‐zirconium phosphate (α‐ZrP?2MIm) in the reaction of glycidyl phenyl ether (GPE) and hexahydro‐4‐methylphthalic anhydride (MHHPA) were investigated. The reaction did not proceed within 1 h at 60 °C. On increasing the temperature to 100 °C, the conversion reached 93% for 1 h. Without the addition of TBD, the conversion was 67% at 100 °C for 1 h. Under storage conditions at 25 °C for 7 days, the conversion of GPE was only 18%. The curing behavior of 2,2‐bis(4‐glycidyloxyphenyl)propane (DGEBA) and MHHPA in the presence of TBD with α‐ZrP?2MIm was evaluated by differential scanning calorimetry. The addition of TBD with α‐ZrP?2MIm as a latent thermal initiator, the storage stability was maintained and the reaction proceeded rapidly under heating conditions. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2557–2561     

Synthesis and properties of new soluble triphenylamine‐based aromatic poly(amine amide)s derived from N,N′‐bis(4‐carboxyphenyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new triphenylamine‐containing aromatic dicarboxylic acid, N,N′‐bis(4‐carboxyphenyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine, was synthesized by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 4‐fluorobenzonitrile, followed by the alkaline hydrolysis of the intermediate dinitrile compound. A series of novel triphenylamine‐based aromatic poly(amine amide)s with inherent viscosities of 0.50–1.02 dL/g were prepared from the diacid and various aromatic diamines by direct phosphorylation polycondensation. All the poly(amine amide)s were amorphous in nature, as evidenced by X‐ray diffractograms. Most of the poly(amine amide)s were quite soluble in a variety of organic solvents and could be solution‐cast into transparent, tough, and flexible films with good mechanical properties. They had useful levels of thermal stability associated with glass‐transition temperatures up to 280 °C, 10% weight‐loss temperatures in excess of 575 °C, and char yields at 800 °C in nitrogen higher than 60%. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 94–105, 2003     

Synthesis and properties of new organo‐soluble and strictly alternating aromatic poly(ester‐imide)s from 3,3‐bis[4‐(trimellitimidophenoxy)phenyl]phthalide and bisphenols

A series of new strictly alternating aromatic poly(ester‐imide)s having inherent viscosities of 0.20–0.98 dL/g was synthesized by the diphenylchlorophosphate (DPCP) activated direct polycondensation of the preformed imide ring‐containing diacid, 3,3‐bis[4‐(trimellitimidophenoxy)phenyl]phthalide (I), with various bisphenols in a medium consisting of pyridine and lithium chloride. The diimide–diacid I was prepared from the condensation of 3,3‐bis[4‐(4‐aminophenoxy)phenyl]phthalide and trimellitic anhydride. Most of the resulting polymers showed an amorphous nature and were readily soluble in a variety of organic solvents such as N‐methyl‐2‐pyrrolidone (NMP) and N,N‐dimethylacetamide (DMAc). Transparent and flexible films of these polymers could be cast from their DMAc solutions. The cast films had tensile strengths ranging 66–105 MPa, elongations at break from 7–10%, and initial moduli from 1.9–2.4 GPa. The glass‐transition temperatures of these polymers were recorded between 208–275 °C. All polymers showed no significant weight loss below 400 °C in the air or in nitrogen, and the decomposition temperatures at 10% weight loss all occurred above 460 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1090–1099, 2000     

Accelerating effects of N‐aryl‐N′,N′‐dialkyl ureas on epoxy‐dicyandiamide curing system

This report focuses on epoxy‐dicyandiamide (DICY) curing system accelerated by N‐aryl‐N′,N′‐dialkyl urea, aiming at clarifying the accelerating mechanism and the relationship between accelerating effect and molecular structure of the accelerators. Nine N‐aryl‐N′,N′‐dialkyl ureas were synthesized and investigated with measurements of differential scanning calorimetry, thermo gravimetric/differential thermal analysis and NMR spectroscopy. The results revealed that the ureas released the corresponding secondary amines by the thermal dissociation in the presence of epoxide, which led to the formation of tertiary amines that catalyze the addition reaction of DICY to epoxide. Moreover, a tendency that the ureas able to release more compact amines exhibited higher acceleration effects was discovered. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis of novel tri‐benzoxazine and effect of phenolic nucleophiles on its ring‐opening polymerization

A trifunctional benzoxazine, 1,3,5‐tris(3‐phenyl‐3,4‐dihydro‐2H‐benzo[1,3]oxazin‐6‐yl)benzene (T‐Bz) was synthesized and in an effort to reduce its curing temperature (curing maxima at 238 °C), it was mixed with various phenolic nucleophiles such as phenol (PH), p‐methoxy phenol (MPH), 2‐methyl resorcinol (MR), hydroquinone (HQ), pyrogallol (PG), 2‐naphthol (NPH), 2,7‐dihydroxy naphthalene (DHN), and 1,1'‐bi‐2‐naphthol (BINOL). The influence of these phenolic nucleophiles on ring‐opening polymerization temperature of T‐Bz was examined by DSC and FTIR analysis. T‐Bz undergoes a complete ring‐opening addition reaction in the presence of bi‐ and trifunctional phenolic nucleophiles (MR/HQ/PG/DHN) at 140 °C (heated for 3 h) and forms a networked polybenzoxazine (NPBz). The NPBzs showed a high thermal stability with T_d20 of 350–465 °C and char yield of 67–78% at 500 °C; however, a diminutive weight loss (6.9–9.8%) was observed at 150–250 °C (T_d5: 215–235 °C) due to degradation of phenolic end groups. This article also gives an insight on how the traces of phenolic impurities can alter the thermal properties of pure benzoxazine monomer as well as its corresponding polymer. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2811–2819     

N‐Benzyl‐2′‐iodo­cinnamanilide and N‐benzyl‐2′‐iodo‐4′‐methyl‐2‐phenyl­cinnamanilide

The aromatic ring of the cinnamic moiety in N‐benzyl‐2′‐iodo­cinnamanilide, C₂₂H₁₈INO, (I), and N‐benzyl‐2′‐iodo‐4′‐methyl‐2‐phenyl­cinnamanilide, C₂₉H₂₄INO, (II), makes a dihedral angle with the iodo­phenyl ring of 72.1 (2) and 81.0 (2)° in (I) and (II), respectively. In (I), mol­ecules exist as discrete components, while in (II), they form infinite chains along the b axis, through I?O non‐bonded interactions.     

N‐(4‐Methyl­phenyl)‐N‐(5‐nitro­furfuryl)‐N‐prop‐2‐ynyl­amine

The title compound, C₁₅H₁₄N₂O₃, is the first example of a structurally determined tertiary amine with both N‐5‐nitro­furfuryl and N‐prop‐2‐ynyl moieties. The mol­ecule is not planar, i.e. the furan ring is inclined at an angle of 84.35 (4)° to the phenyl ring. The crystal structure is dominated by van der Waals forces. The terminal alkynyl group as the strongest C—H hydrogen‐bond donor is not involved in hydrogen‐bond formation.     

Asymmetric anionic polymerizations of 7‐(o‐substituted phenyl)‐2,6‐dimethyl‐1,4‐benzoquinone methides: Electrostatic interaction and steric,inductive, and resonance effects of the ortho‐substituent on the optical activity

7‐(o‐Substituted phenyl)‐2,6‐dimethyl‐1,4‐benzoquinone methides which have an electron‐donating methoxy‐(o‐OMe, 2a ) and methyl‐ (o‐Me, 2b ) substituents or an electron‐withdrawing cyano‐ (o‐CN, 2c ) and trifluoromethyl‐ (o‐CF₃, 2d ) substituents at the ortho‐position of the aromatic ring and 7‐(m‐substituted phenyl)‐2,6‐dimethyl‐1,4‐benzoquinone methide with an electron‐withdrawing trifluoromethyl‐ (m‐CF₃, 2e ) substituent at the meta‐position of the aromatic ring were synthesized, and their asymmetric anionic polymerizations using the complex of lithium 4‐isopropylphenoxide with (?)‐sparteine were carried out in toluene at 0 °C. The polymers with negative optical activity were obtained for all of five monomers, and their specific rotation values largely changed depending upon the substituents of the monomers. On the basis of the comparison of various substituents effects, it was found that the specific rotation of obtained polymers is significantly affected by the electronic effects such as inductive and resonance effects rather than the steric and electrostatic effects of the substituent. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1048–1058     

Novel,organosoluble, light‐colored fluorinated polyimides based on 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl or 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl

Two series of fluorinated polyimides were prepared from 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl ( 2 ) and 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl ( 4 ) with various aromatic dianhydrides via a conventional, two‐step procedure that included a ring‐opening polyaddition to give poly(amic acid)s, followed by chemical or thermal cyclodehydration. The inherent viscosities of the polyimides ranged from 0.54 to 0.73 and 0.19 to 0.36 dL/g, respectively. All the fluorinated polyimides were soluble in many polar organic solvents, such as N,N‐dimethylacetamide and N‐methylpyrrolidone, and afforded transparent and light‐colored films via solution‐casting. These polyimides showed glass‐transition temperatures in the ranges of 222–280 and 257–351 °C by DSC, softening temperatures in the range of 264–301 °C by thermomechanical analysis, and a decomposition temperature for 10% weight loss above 520 °C both in nitrogen and air atmospheres. The polyimides had low moisture absorptions of 0.23–0.58%, low dielectric constants of 2.84–3.61 at 10 kHz, and an ultraviolet–visible absorption cutoff wavelength at 351–434 nm. Copolyimides derived from the same dianhydrides with an equimolar mixture of 4,4′‐oxydianiline and diamine 2 or 4 were also prepared and characterized. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2416–2431, 2004