Sulfobetaine zwitterionomers based on n‐butyl acrylate and 2‐ethoxyethyl acrylate: Physical properties

New materials with potential applications for adhesives and coatings, based on copolymers containing zwitterionic pendent groups, were investigated. n‐Butyl acrylate and 2‐ethoxyethyl acrylate were copolymerized with a series of five zwitterionic sulfobetaine monomers (SBMs). The structures of the SBMs were varied systematically in terms of (1) intercharge spacing in the zwitterionic moiety and (2) substituent bulkiness at the quaternary ammonium functionality. The effect of varying the sulfobetaine content and structure in the copolymers was investigated, with an emphasis on ion aggregation behavior and physical properties, with dynamic mechanical analysis. The zwitterionomers exhibited the expected biphasic morphology, with the appearance of an ion‐rich glass‐transition temperature. An increase in the storage modulus was observed with increasing SBM content in the rubbery and terminal regions, suggesting an increased degree of ionic crosslinking in the rubbery region and decreased chain mobility in the flow region. Intercharge spacing variation in the sulfobetaine moiety did not have a significant effect on the modulus–temperature curves, contrary to our expectations. Increases in the modulus were much less pronounced for the bulkier SBMs than for the other monomers, possibly because of hindered aggregation of the sulfobetaine moieties. Likewise, matrix polarity had a greater influence on the physical properties of these materials than intercharge separation in the SBMs. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2303–2312, 2002     

Low‐temperature route to thermoplastic polyamide elastomers

Thermoplastic polyamide elastomers were obtained by polymerization of aminobenzoyl‐substituted telechelics derived from poly(tetrahydrofuran)‐diols (number‐average molecular weight: 1400 or 2000 g mol^?1) with several diacid dichlorides (terephthaloyl dichloride, 4,4′‐biphenyldicarbonyl dichloride, or 2,6‐naphthalenedicarbonyl dichloride) and chlorotrimethylsilane in N,N‐dimethylacetamide at 0–20 °C. The as‐prepared polymers had melting temperatures above 190 °C and exhibited elastic properties at room temperature, as evidenced by dynamic mechanical analysis and stress–strain measurements. The polymer with 2,6‐naphthalenedicarboxamide hard segments had the widest rubbery plateau within the series, the highest extension at break, and good recovery properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1449–1460, 2004     

Glass transition temperature of allyl methacrylate‐n‐butyl acrylate gradient copolymers in dependence on chemical composition and molecular weight

Glass transition temperatures (T_gs) of P(AMA‐co‐BA) copolymers and the corresponding homopolymers, where AMA is allyl methacrylate and BA is n‐butyl acrylate, obtained by means of atom transfer radical polymerization were measured using differential scanning calorimetry. Because of the (pseudoliving) nature of this polymerization technique an increase in molecular weight (MW) is produced as the reaction progresses, which gives rise to an increase in T_gs. This increment can be adequately described by the Fox–Flory's equation in both homopolymers. However, in the spontaneous gradient copolymers of P(AMA‐co‐BA), the expected increase in T_g with the augment of the monomer conversion is compensated by the enrichment of BA as the polymerization reaction progresses. These opposite effects with respect to the T_g values almost balance each other, and therefore no significant influence on the MW or on conversion is found. This fact establishes that T_gs can be used to describe the profile of these gradient copolymers, and can be theoretically determined because of its dependence on the molar fraction in the copolymer. From this dependence on chemical composition along with the experimental behavior, a prediction of the T_g variation with the MW was performed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1845–1855, 2007     

Effect of solvent–matrix interactions on structures and mechanical properties of micelle‐crosslinked gels

Previous studies on hydrogels crosslinked by acrylated PEO₉₉–PPO₆₅–PEO₉₉ triblock copolymer (F127DA) micelles demonstrate outstanding strength and toughness, which is attributed to the efficient energy dissipation through the hydrophobic association in the micelles. The current study further focuses on how the solvent property affects the structures and the mechanical properties of F127DA micelle crosslinked polyacrylamide gels. Binary solvents comprised of dimethyl sulfoxide (DMSO) and water are used to adjust the polymer/solvent interactions, which consequently tune the conformations of the polymer chains in the network. The presence of DMSO significantly decreases the strength but increased the stretchability of the gels, whereas the overall tensile toughness remained unchanged. In situ small‐angle X‐ray scattering measurements reveal the deformation of micelles along with the stretching direction. A structure evolution mechanism upon solvent change is proposed, according to the experimental observations, to explain influence of solvent quality on the mechanical properties of the micelle‐crosslinked gels. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 473–483     

Synthesis of n‐alkyl methacrylate polymers with pendant carbazole moieties and their derivatives

New methacrylate monomers with carbazole moieties as pendant groups were synthesized by multistep syntheses starting from carbazoles with biphenyl substituents in the aromatic ring. The corresponding polymers were prepared using a free‐radical polymerization. The novel polymers contain N‐alkylated carbazoles mono‐ or bi‐substituted with biphenyl groups in the aromatic ring. N‐alkyl chains in polymers vary by length and structure. All new polymers were synthesized to evaluate the structural changes in terms of their effect on the energy profile, thermal, dielectric, and photophysical properties when compared to the parent polymer poly(2‐(9H‐carbazol‐9‐yl)ethyl methacrylate). According to the obtained results, these compounds may be well suited for memory resistor devices. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 70–76     

Poly(butylene terephthalate‐co‐5‐tert‐butyl isophthalate) copolyesters: Synthesis,characterization, and properties

A series of poly(butylene terephthalate) copolyesters containing 5‐tert‐butyl isophthalate units up to 50 mol %, as well as the homopolyester entirely made of these units, were prepared by polycondensation from a melt. The microstructure of the copolymers was determined by NMR to be random for the whole range of compositions. The effect exerted by the 5‐tert‐butyl isophthalate units on thermal, tensile, and gas transport properties was evaluated. Both the melting temperature (T_m) and crystallinity were found to decrease steadily with copolymerization, whereas the glass‐transition temperature (T_g) increased and the polyesters became more brittle. Permeability and solubility slightly increased with the content in substituted isophthalic units, whereas the diffusion coefficient remained practically constant. For the homopolyester poly(5‐tert‐butyl isophthalate), all these properties were found to deviate significantly from the general trend displayed by copolyesters, suggesting that a different structure in the solid state is likely adopted in this case. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 92–100, 2005     

Triblock copolymers based on styrene and n‐butyl acrylate by nitroxide‐mediated radical polymerization: problems and solutions

Controlled radical polymerization (CRP) has been experiencing tremendous developments of late, with spectacular achievements in macromolecular engineering. Well‐defined star polymers as well as block copolymers can be obtained using miscellaneous CRP methods. This paper is the second of a series devoted to the synthesis of triblock copolymers by nitroxide‐mediated polymerization, using a β‐hydrogen containing phosphonylated nitroxide (SG1) as stable radical. It focuses on the problems associated with the sequential polymerization of styrene and n‐butyl acrylate while synthesizing poly(styrene‐b‐n‐butyl acrylate‐b‐styrene) copolymers from SG1‐based macromolecular alkoxyamines. In particular, it discloses how the blocking efficiency can be improved when growing the second poly(n‐butyl acrylate) (PBuA) block from the first polystyrene (PS) block. The proportion of dead chains that contaminate such triblock samples is also evaluated.     

Combination of nitroxide‐mediated polymerization and SET‐LRP for the synthesis of high molar mass branched and star‐branched poly(n‐butyl acrylate) characterized by size exclusion chromatography and rheology

Branched and star‐branched polymers were successfully synthesized by the combination of two successive controlled radical polymerization methods. A series of linear and star poly(n‐butyl acrylate)‐co‐poly(2‐(2‐bromoisobutyryloxy) ethyl acrylate) statistical copolymers, P(nBA‐co‐BIEA)_x, were first synthesized by nitroxide‐mediated polymerization (NMP at T > 100 °C). The subsequent polymerization of n‐butyl acrylate by single electron transfer‐living radical polymerization (SET‐LRP at T = 25 °C), initiated from the brominated sites of the P(nBA‐co‐BIEA)_x copolymer, produced branched or star‐branched poly(n‐butyl acrylate) (PnBA). Both types of polymerizations (NMP and SET‐LRP) exhibited features of a controlled polymerization with linear evolutions of logarithmic conversion versus time and number‐average molar masses versus conversion for final M_n superior to 80,000 g mol^?1. The branched and star‐branched architectures with high molar mass and low number of branches were fully characterized by size exclusion chromatography. The Mark–Houwink Sakurada relationship and the analysis of the contraction factor (g′ = ([η]_branched/[η]_linear)_M) confirmed the elaboration of complex PnBA. The zero‐shear viscosities of the linear, star‐shaped, branched, and star‐branched polymers were compared. The modeling of the rheological properties confirmed the synthesis of the branched architectures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Perylene diimide copolymers with dithienothiophene and dithienopyrrole: Use in n‐channel and ambipolar field‐effect transistors

Solution‐processable polymers consisting of perylene diimide (PDI) acceptor moieties alternating with dithienothiophene (DTT), N‐dodecyl‐dithienopyrrole (DTP), or oligomers of these donor groups have been synthesized. We have, in addition to varying the donor, varied the N,N′ substituents of the PDIs. The thermal, optical, electrochemical, and charge‐transport properties of the polymers have been investigated. The polymers show broad absorption extending from 300 to 1000 nm with optical band gaps as low as 1.2 eV; the band gap decreases with increasing the conjugation length of donor block, or by replacement of DTT by DTP. The electron affinities of the polymers, estimated from electrochemical data, range from ?3.87 to ?4.01 eV and are slightly affected by the specific choice of donor moiety, while the estimated ionization potentials (?5.31 to ?5.92 eV) are more sensitive to the choice of donor. Bottom‐gate top‐contact organic field‐effect transistors based on the polymers generally exhibit n‐channel behavior with electron mobilities as high as 1.7 × 10^–2 cm²/V/s and on/off ratios as high as 10⁶; one PDI‐DTP polymer is an ambipolar transport material with electron mobility of 4 × 10^–4 cm²/V/s and hole mobility of 4 × 10^–5 cm²/V/s in air. There is considerable variation in the charge transport properties of the polymers with the chemical structures. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of poly(n‐butyl acrylate) homopolymer and poly(styrene‐b‐n‐butyl acrylate‐b‐styrene) triblock copolymer via AGET emulsion ATRP using a cationic surfactant

Cationic emulsions of triblock copolymer particles comprising a poly(n‐butyl acrylate) (PⁿBA) central block and polystyrene (PS) outer blocks were synthesized by activator generated by electron transfer (AGET) atom transfer radical polymerization (ATRP). Difunctional ATRP initiator, ethylene bis(2‐bromoisobutyrate) (EBBiB), was used as initiator to synthesize the ABA type poly(styrene‐b‐n‐butyl acrylate‐b‐styrene) (PS‐PⁿBA‐PS) triblock copolymer. The effects of ligand and cationic surfactant on polymerizations were also discussed. Gel permeation chromatography (GPC) was used to characterize the molecular weight (M_n) and molecular weight distribution (MWD) of the resultant triblock copolymers. Particle size and particle size distribution of resulted latexes were characterized by dynamic light scattering (DLS). The resultant latexes showed good colloidal stability with average particle size around 100–300 nm in diameter. Glass transition temperature (T_g) of copolymers was studied by differential scanning calorimetry (DSC). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 611–620     

Mechanisms of n‐butanol formation in butyl acrylate latexes

The mechanisms involved in the formation of n‐butanol during the synthesis of butyl acrylate containing latices were investigated. The experimental results showed that neither the hydrolysis of butyl acrylate nor of the ester bond in the butyl acrylate segments of the polymer played a major role in the formation of n‐butanol, which was mainly generated from the polymer backbone, by transfer reactions to polymer chain followed by cyclization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5838–5846, 2007     

The preparation of t‐butyl acrylate,methyl acrylate,and styrene block copolymers by atom transfer radical polymerization: Precursors to amphiphilic and hydrophilic block copolymers and conversion to complex nanostructured materials

Atom transfer radical polymerization conditions with copper(I) bromide/pentamethyldiethylenetriamine (CuBr/PMDETA) as the catalyst system were employed for the polymerization of tert‐butyl acrylate, methyl acrylate, and styrene to generate well‐defined homopolymers, diblock copolymers, and triblock copolymers. Temperature studies indicated that the polymerizations occurred smoothly in bulk at 50 °C. The kinetics of tert‐butyl acrylate polymerization under these conditions are reported. Well‐defined poly(tert‐butyl acrylate) (PtBA; polydispersity index = 1.14) and poly(methyl acrylate) (PMA; polydispersity index = 1.03) homopolymers were synthesized and then used as macroinitiators for the preparation of PtBA‐b‐PMA and PMA‐b‐PtBA diblock copolymers in bulk at 50 °C or in toluene at 60 or 90 °C. In toluene, the amount of CuBr/PMDETA relative to the macroinitiator was important; at least 1 equiv of CuBr/PMDETA was required for complete initiation. Typical block lengths were composed of 100–150 repeat units per segment. A triblock copolymer, composed of PtBA‐b‐PMA‐b‐PS (PS = polystyrene), was also synthesized with a well‐defined composition and a narrow molecular weight dispersity. The tert‐butyl esters of PtBA‐b‐PMA and PtBA‐b‐PMA‐b‐PS were selectively cleaved to form the amphiphilic block copolymers PAA‐b‐PMA [PAA = poly(acrylic acid)] and PAA‐b‐PMA‐b‐PS, respectively, via reaction with anhydrous trifluoroacetic acid in dichloromethane at room temperature for 3 h. Characterization data are reported from analyses by gel permeation chromatography; infrared, ¹H NMR, and ¹³C NMR spectroscopies; differential scanning calorimetry; and matrix‐assisted, laser desorption/ionization time‐of‐flight mass spectrometry. The assembly of the amphiphilic triblock copolymer PAA₉₀‐b‐PMA₈₀‐b‐PS₉₈ within an aqueous solution, followed by conversion into stable complex nanostructures via crosslinking reactions between the hydrophilic PAA chains comprising the peripheral layers, produced mixtures of spherical and cylindrical topologies. The visualization and size determination of the resulting nanostructures were performed by atomic force microscopy, which revealed very interesting segregation phenomena. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4805–4820, 2000     

AB and ABA type butyl acrylate and styrene block copolymers via RAFT‐mediated miniemulsion polymerization

Two trithiocarbonate reversible addition fragmentation chain transfer (RAFT) agents are compared in miniemulsion polymerization of styrene and butyl acrylate and the formation of seeded emulsion block copolymers. The order of block synthesis and the number of block segments per polymer are discussed. The use of nonionic surfactants is examined and the type of surfactant in relation to the monomer used is found to have a significant affect on latex formation. Conditions are shown by which AB and ABA type block copolymers can be successfully prepared via a seeded RAFT‐mediated emulsion polymerization. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 588–604, 2007     

Viscoelastic and damping characteristics of poly(n‐butyl acrylate)‐poly(n‐butyl methacrylate) semi‐IPN latex films

This article reports the synthesis, characterization, and damping characteristics of semi‐interpenetrating (semi‐IPN) latex systems composed of poly n‐butyl acrylate (PBA) core and poly n‐butyl methacrylate (PBMA) shell. The IPN's were prepared by seeded emulsion polymerization using crosslinked PBA seeds with varying crosslinker (m‐diisopropenyl benzene) concentration. The polymer weight ratio in the first and second stage polymerization is maintained at 1:1 in all the cases. The particle size determined by dynamic light scattering shows a decrease in the shell thickness with increasing crosslinker concentration of the seed. The mechanical properties, like Shore A hardness of the films, increased from 18 to 65 when the crosslinker concentration is increased from 0 to 4.8 mol%. The dynamic mechanical studies show that the modulus value of the IPN's is below that of non‐crosslinked films, and the value depends upon the crosslink density of the seed. Mechanical models, such as the Kerner's model and the Takayanagi's model, were used to explain the variation in the dynamic mechanical properties with the degree of seed crosslinking. The study indicates lower bound (rubbery) behavior for the films with lightly crosslinked cores. The study also shows that, at lower crosslinker concentration enhanced phase separation and better damping properties are achieved but at higher cross linker concentration (>2 mol%) greater interpenetration of the shell monomer to the cores takes place and tough films, with reduced damping properties are formed. Copyright © 2007 John Wiley & Sons, Ltd.     

Nitroxide‐mediated radical polymerization of 2‐(dimethylamino)ethyl acrylate and its sequential block copolymerization with styrene and N‐butyl acrylate

Nitroxide‐mediated radical polymerization (NMRP) of 2‐(dimethylamino)ethyl acrylate (DMAEA) was carried out at 100–120 °C, initiated by MONAMS, an alkoxyamine based on N‐tert‐butyl‐N‐(1‐diethyl phosphono‐2,2‐dimethylpropyl)nitroxide, SG1. Controlled polymerization can be achieved by the addition of free SG1 (the initial molar ratio of SG1 to MONAMS ranged from 0.06 to 0.12), giving a linear first‐order kinetic plot up to 55–70% conversion depending on the reaction conditions. The molecular weights show a near linear increase with conversion; however, they deviate to some extent with theoretical values. SG1‐mediated polymerization of DMAEA at 112 °C is also controlled in organic solvents (N,N‐dimethylformide, anisole, xylene). Polymerization rate increases with increasing solvent polarity. Chain transfer to polymer produces ～1 mol % branches in bulk and 1.2–1.9 mol % in organic solvents, typical of those for acrylates. From poly(styrene) (pS) and poly(n‐butyl acrylate) (pBA) macroinitiators, amphiphilic di‐ and triblock copolymers p(S‐b‐DMAEA), p(DMAEA‐b‐S‐b‐DMAEA), p(BA‐b‐DMAEA), and p(DMAEA‐b‐BA‐b‐DMAEA) were synthesized via NMRP at 110 °C. Polymers were characterized by GPC, NMR, surface tension measurements, and DSC. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 414–426, 2006     

Synthesis,characterization, and properties of hydroxyl‐terminated copolysiloxanes containing γ‐cyanopropyl groups

A series of random copolysiloxanes (PCDMS) containing various amount of γ‐cyanopropyl groups are prepared by a new method under mild conditions. Structures of the synthesized polymers are fully characterized by FTIR, ¹H NMR, ²⁹Si NMR, and GPC. Rheological properties of PCDMS are tested by cone and plate rheometer, and thermal properties by differential scanning calorimetry (DSC) and thermogravimetry analysis (TGA). Damping properties as well as fuel resistance of the cured PCDMS elastomers are also tested. The correlation between chemical structure, content of cyanopropyl group and properties are discussed. With the increasing amount of polar cyanopropyl group introduced, glass transition temperatures (T_g) of the synthesized PCDMS gradually increases from ?121 to ?65 °C, residual weight increases from 0 to 36% at 800°C, loss factor reaches as high as 1.74, mass increase under fuel immersion for 14 days can be as low as 3.6%. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1408–1421     

Synthesis and characterization of functional gradient copolymers of allyl methacrylate and butyl acrylate

Functional spontaneous gradient copolymers of allyl methacrylate (A) and butyl acrylate (B) were synthesized via atom transfer radical polymerization. The copolymerization reactions were carried out in toluene solutions at 100 °C with methyl 2‐bromopropionate as the initiator and copper bromide with N,N,N′,N″,N″‐pentamethyldiethylenetriamine as the catalyst system. Different aspects of the statistical reaction copolymerizations, such as the kinetic behavior, crosslinking density, and gel fraction, were studied. The gel data were compared with Flory's gelation theory, and the sol fractions of the synthesized copolymers were characterized by size exclusion chromatography and nuclear magnetic resonance spectroscopy. The copolymer composition, demonstrating the gradient character of the copolymers, and the microstructure were analyzed. The experimental data agreed well with data calculated with the Mayo–Lewis terminal model and Bernoullian statistics, with monomer reactivity ratios of 2.58 ± 0.37 and 0.51 ± 0.05 for A and B, respectively, an isotacticity parameter for A of 0.24, and a coisotacticity parameter of 0.33. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5304–5315, 2006     

Synthesis,characterization, and rheological properties of hybrid titanium star‐shaped poly(n‐butyl acrylate)

The synthesis of hybrid star‐shaped polymers was carried out by atom transfer radical polymerization of n‐butyl acrylate from a well‐defined multifunctional titanium‐oxo‐cluster initiator. Conditions were identified to prevent possible side reactions among monomer, polymer, and the titanium‐oxo‐cluster ligands. Polymerizations provided linear first‐order kinetics and the evolution of the experimental molecular weight is also linear with the conversion. ¹H DOSY NMR and cleavage of the polymeric branches from the multifunctional initiator by hydrolysis were used to (i) prove the star‐shaped structure of the polymer, and (ii) demonstrate that the shoulder observed on size exclusion chromatograms is not due to a noncontrolled polymerization but to ungrafting of polymeric branches during analysis. Rheological properties of the hybrid star‐shaped poly(n‐butyl acrylate) were studied in the linear regime and show that the Ti‐oxo‐cluster not only increases significantly the viscosity of the polymer relative to its ungrafted arm but has a rheological signature which is qualitatively different from that of stars with organic cores suggesting that the Ti cluster reduces significantly the molecular mobility of the star. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Dependence of dielectric,ferroelectric, and piezoelectric properties on crystalline properties of p(VDF‐co‐TrFE) copolymers

Thermal processing at various temperatures has been used to fabricate poly(vinylidene fluoride‐co‐trifluoroethylene) [P(VDF‐co‐TrFE)] films with varied crystalline properties in an attempt to improve their piezoelectric properties. Although the dielectric constant of the films annealed at higher temperature is smaller than that of cooled and quenched ones, it has been shown that the annealed films possess larger crystallinity and stacked lamellar crystal grain size. The ferroelectric domains deriving from crystal region in all the samples are effectively improved by hot polarization. As a result, the remnant polarizations (P_r) and coercive electric field (E_c) of the corresponding films are improved at a low frequency due to the response of dipoles in crystal phase, and the largest piezoelectric constant in the longitudinal thickness mode (d₃₃=?25 pC/N) is obtained in an annealed copolymer film. The results illustrate improving the crystal structure of P(VDF‐co‐TrFE) is an effective way to realize high electromechanical properties, which provides broadly applied scenery for this kind of copolymer in piezoelectric components. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012