Electrospinning‐induced shape memory effect in thermoplastic polyurethane characterization and thermoviscoelastic modeling

Electrospun thermoplastic polyurethane (TPU) nanofibers are known to contract considerably (～40%) on heating up to ～90 °C. This study investigates this thermomechanical behavior and the TPU shape memory capabilities. The shape memory effect was first studied in TPU films as a model system by applying classical thermomechanical cycles (programming and recovery). The films were able to fix the applied deformation during long‐term storage at room temperature, well above the material's calorimetric glass transition temperature and in the absence of a percolated structure of hard domains. Structural analysis (Fourier transform infrared, differential scanning calorimeter, and dynamic mechanical analysis) revealed broad thermal transitions indicating the presence of a mixed phase of hard segments dispersed in the soft segment matrix. Using a linear viscoelastic model together with time–temperature superposition, the shape memory effect was attributed to the thermoviscoelastic properties of TPU. In particular, the mixed phase was found to give rise to a very broad relaxation spectrum dominated by long relaxation times, which explains the suppression of strain recovery at room temperature. Finally, the electrospinning process was examined and was found to be similar to a programming cycle characterized by the strong elongation flow accompanied by massive solvent evaporation, whereas the contraction effect was interpreted as the recovery phase in a shape memory perspective. Thus, the contraction of electrospun TPU mats may be considered to be an electrospinning‐induced shape memory effect. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1590–1602     

Thermo-mechanical behavior of electrospun thermoplastic polyurethane nanofibers

Analysis of the thermo-mechanical behavior of electrospun thermoplastic polyurethane (TPU) block co-polymer nanofibers (glass transition temperature ∼−50 °C) is presented. Upon heating, nanofibers began to massively contract, at ∼70 °C, whereas TPU cast films started to expand. Radial wide-angle X-ray scattering (WAXS) profiles of the nanofibers and the films showed no diffraction peaks related to crystals, whereas their amorphous halo had an asymmetric shape, which can be approximated by two components, associated with hard and soft segments. During heating, noticeable changes in the contribution of these components were only observed in nanofibers. These changes, which were accompanied with an endothermic DSC peak, coinciding with the start of the nanofibers contraction, can be attributed to relaxation of an oriented stretched amorphous phase created during electrospinning. Such structure relaxation becomes possible when a portion of the hard segment clusters, forming an effective physical network, is destroyed upon heating.     

Thermal shrinkage of electrospun PVP nanofibers

This paper outlines the shrinkage of electrospun polyvinylpyrrolidone (PVP) fiber mats during thermal treatment. The thermal behavior and phase changes within the fibers were investigated by DSC and TGA/DTA. Five precursors with different PVP loading in ethanol were electrospun. The mats shrinkage as function of temperature was measured in the RT–200 °C range. Shrinkage rate drastically increased above the polymer glass transition point, T_g (150–180 °C), due to increase in polymer chain mobility. Mats shrinkage at 200 °C as function of PVP concentration showed a minimum at ∼10%wt. Below 10% PVP the mats morphology is non‐uniform, consisting of beads and fibers. Above 10% PVP, only flat and uniform fibers were observed. This paper outlines the dominant mechanism governing the mats shrinkage during heating. In addition, the effect of PVP concentration on the expansion of fibers diameter was investigated and found to be consistent with the linear shrinkage observing a minimum at ∼10% PVP. The effect of applied voltage on mat shrinkage was investigated, and showed a minimum at 12 kV. Understanding the interplay between fibers morphology and thermal shrinkage allows precursor composition and system optimization needed for minimizing shrinkage negative effects on the structure and properties of electrospun fiber mats. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 248–254     

Effect of constrained annealing on the mechanical properties of electrospun poly(ethylene oxide) webs containing multiwalled carbon nanotubes

In this work, flexible nanofibrous membranes (mats) of poly(ethylene oxide) (PEO) with and without multiwall carbon nanotubes (MWNTs) were fabricated by electrospinning. The effects of annealing and MWNT concentration on mat morphology, MWNT dispersion within the nanofibers, and the mechanical properties of electrospun mats were studied. Annealing temperatures ranged from 60 °C to 64 °C [near the melting temperature (64 °C via differential scanning calorimetry)] for 4 minutes. Samples were annealed with and without applied tension (constrained and unconstrained annealing). Annealing at the highest temperature (64 °C), before the loss of fibrous morphology, significantly improved fiber–fiber bonding and therefore the tensile strength of the mats. Compared with unconstrained annealing, constrained annealing introduced fiber alignment (and therefore molecular orientation) along the tensile axis (direction of constraint) during annealing and resulted in a significant increase in modulus for all samples (with and without MWNTs). The use of constrained annealing may be a facile approach to enhance modulus in nanofibrous mats while maintaining high porosity. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 787–796     

A novel method for a high‐strength electrospun meta‐aramid nanofiber by microwave treatment

Electrospun nanofibers have attracted great attention as potential reinforcements in composite application due to their high specific surface area, high porosity, and versatility. Because the electrospun nanofibers exhibit relatively low mechanical strength due to low crystallinity and random alignment, many researchers have tried to enhance the mechanical strength through various approaches, such as heat treatment and fiber orientation control. These methods, however, are difficult to control and require the use of high temperatures and sophisticated apparatuses, and high costs. In this study, we investigate a novel microwave technique to fabricate high‐strength electrospun meta‐aramid nanofiber mats. To optimize the microwave irradiation conditions, the electrospun nanofiber was treated at varying levels of moisture and for different irradiation times. Field emission scanning electron microscopy was used to observe the surface morphology of the electrospun nanofiber mats at the different irradiation times. The changes in the crystallinity and thermal properties were investigated using X‐ray diffraction and thermogravimetric analysis measurements. Tensile tests were performed to measure the mechanical strength of the meta‐aramid nanofiber mats with respect to each parameter. As a result, any residual solvents and salts were removed, and the degree of crystallization was dramatically increased by microwave irradiation under wet conditions. These effects led to a 2.8‐fold increase in the tensile strength of the nanofiber mats compared with an untreated mat. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 807–814     

Thermoresponsive conductive polymer composite thin film and fiber mat: Crosslinked PEDOT:PSS and P(NIPAAm‐co‐NMA) composite

The thermoresponsive conductive composite (TCC) thin films and fiber mats, whose electrical property changed with temperature, were fabricated successfully. The thermocrosslinkable and thermoresponsive copolymer, poly(N‐isopropyl acrylamide‐co‐N‐methylolacrylamide) (PNN), was synthesized. The TCC thin film and fiber mat were fabricated by spin coating and electrospinning process of PEDOT:PSS/PNN solutions, respectively. After thermocrosslinking and doping by DMSO, the composite thin films and fiber mats were obtained. Fibrous structures of TCC fiber mats were observed by SEM. The surface resistance and conductivity of composites were measured. The thermoresponsivity and swelling ratio of TCCs were also studied. The thermoresponsive conductive property was analyzed by measuring the surface resistance of TCCs in water bath under various temperatures from 20 to 50 °C. With the increase of temperature, the TCCs shrank to be dense structure and showed lower surface resistance. The TCC fibers mat exhibited greater sensitivity to temperature than thin film owing to its fibrous structure. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1078–1087     

Electrospinning of biostable polyisobutylene-based thermoplastic polyurethanes

Electrospinning of a previously synthesized biostable polyisobutylene (PIB)-based thermoplastic polyurethanes (TPU) have been performed as materials with potential applications as vascular grafts. Electrospun mats were generated with fiber diameters in the submicron to 2 μm range as observed using scanning electron microscopy. Porosity of electrospun TPU fiber mats was investigated using Hg intrusion porosimetry. Fiber mats were found to have a distribution of pore sizes between 100 nm and 100 μm, with overall porosity between 50 and 70%. Thermal analysis of electrospun mats showed orientation of the TPU chains compared to the bulk as-synthesized material. Tensile failure properties were characterized, showing ultimate tensile strength of 1.6–6.5 MPa and ultimate elongation of ∼300–100% with TPUs of increasing hardness from Shore 60A to 100A. Strain-recovery experiments showed good recovery of tensile strain at significant stresses. The previously demonstrated biostability of these PIB-based TPUs, together with the excellent reported mechanical properties, indicates great promise for these materials as biostable vascular grafts. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Carbendazim‐loaded electrospun poly(vinyl alcohol) fiber mats and release characteristics of carbendazim therefrom

Ultra‐fine poly(vinyl alcohol) (PVA) electrospun fiber mats containing carbendazim were successfully fabricated by electrospinning from the neat PVA solution containing carbendazim in various amounts based on the weight of PVA. The morphological appearance of both the neat and the carbendazim‐loaded electrospun PVA fibers were smooth and the incorporation of carbendazim in the neat PVA solution did not affect the morphology of the resulting fibers. The average diameters of the neat and the carbendazim‐loaded electrospun PVA fibers ranged between 155 and 160 nm. The chemical integrity of the as‐loaded carbendazim in the carbendazim‐loaded electrospun PVA fiber mats was intact as verified by the ¹H‐nuclear magnetic resonance spectroscopy. Thermal properties of the carbendazim‐loaded electrospun PVA fiber mats were analyzed by differential scanning calorimetry and thermogravimetric analysis. The release characteristics of the carbendazim‐loaded electrospun PVA mats were investigated by the total immersion method in distilled water at 30°C. The carbendazim‐loaded electrospun PVA mats exhibited greater amount of carbendazim released than the carbendazim‐loaded as‐cast films. Copyright © 2010 John Wiley & Sons, Ltd.     

The potential use of electrospun polylactic acid nanofibers as alternative reinforcements in an epoxy composite system

This pilot study elaborates the development of novel epoxy/electrospun polylactic acid (PLA) nanofiber composites at the fiber contents of 3, 5, and 10 wt % to evaluate their mechanical and thermal properties using flexural tests and differential scanning calorimetry (DSC). The flexural moduli of composites increase remarkably by 50.8 and 24.0% for 5 and 10 wt % fiber contents, respectively, relative to that of neat epoxy. Furthermore, a similar trend is also shown for corresponding flexural strengths being enhanced by 31.6 and 4.8%. Fractured surface morphology with scanning electron microscopy (SEM) confirms a full permeation of cured epoxy matrix into nanofiber structures and existence of nondestructive fibrous networks inside large void cavities. The glass transition temperature (T_g) of composites increases up to 54–60 °C due to embedded electrospun nanofibers compared to 50 °C for that of epoxy, indicating that fibrous networks may further restrict the intermolecular mobility of matrix in thermal effects. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 618–623     

Thermal response of a PVCL–HA conjugate

The synthesis and self‐assembling of a thermoresponsive conjugate of hyaluronic acid (HA) and poly(N‐vinylcaprolactam) (PVCL) is reported. Both polymers were end functionalized: HA via reductive amination, thereby introducing an azide endgroup to the chain end, and PVCL via thioetherification to introduce a propargyl group. The two were coupled with a copper assisted “click” reaction into a bioconjugate composed of HA blocks with the molar mass 3,600 g mol^?1 (1618 saccharide units) and PVCL blocks of 3,500 g mol^?1 (～25 repeating units). The cloud point temperature measured by transmittance was 50–51 °C in water. The calorimetrically observed phase transition temperature of PVCL in the conjugate increased by 2 °C to 47.7 °C, whereas the enthalpy of the phase transition was unaffected by the conjugation. HA‐PVCL conjugate self‐assembles in water upon heating into monodisperse, colloidally stable, hollow spherical particles whose size may be tuned with the heating rate of the solution. Slow and fast heating resulted in vesicles with the hydrodynamic radii of 443 or 275 nm, respectively. The heating rate did not, however, affect the cloud point. Salt did not noticeably affect the size of the polymer particles, presumably because of interactions between the HA and PVCL blocks. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 425–436     

Phase morphology and mechanical properties of the electrospun polyoxymethylene/polyurethane blend fiber mats

Polyoxymethylene/thermoplastic polyurethane (POM/TPU) blends containing 10–30 wt % of TPU were electrospun using hexafluoroisopropanol as the solvent. The average fiber diameter increases with the increase in TPU content from 0.68 μm for neat POM fibers to 0.92 μm for POM/TPU 7:3 blend fibers due to the increase in solution viscosity. Core/sheath structure with the major component POM as the core and the minor component TPU as the sheath was observed by transmission electron microscopy and further confirmed by surface N contents of the blend fiber mats. The crystalline melting point and the degree of crystallinity of POM have no obvious change by coelectrospinning with TPU due to lack of interaction between POM and TPU as revealed by Fourier transform infrared spectroscopy. Tensile tests showed that the unusual high ductility of POM fiber mat could be further increased by coelectrospinning with 10 or 20 wt % TPU without significantly decreasing the stiffness and strength. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1853–1859, 2009     

Processing and characterization of oriented electrospun poly(vinylidene fluoride) mats

Mats of highly oriented poly(vinylidene fluoride) nanofibers were electrospun by means of a conventional electrospinning equipment; the orientation, however, was obtained using a disk collector rotating at a speed of 4000 rpm and a device that reduced the influence of air displacement during nanofiber orientation. Thermal transitions of the mats were determined by differential scanning calorimetry, the predominant crystalline phase by Fourier transform infrared spectroscopy and wide‐angle X‐ray scattering and the nanofiber orientation and morphology by scanning electron microscopy. Relative permittivity, loss index, stable remnant polarization, and coercive field of the mats were also determined and compared with those obtained for a mat electrospun at 2000 rpm and an oriented commercial film. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 000: 000–000, 2012     

Crystalline structure and morphology of biaxially oriented polyamide‐11 films

The effect of the uniaxial and biaxial stretching and subsequent solution annealing of extrusion‐cast polyamide‐11 films on the crystalline structure and morphology was investigated with differential scanning calorimetry, wide‐angle X‐ray diffraction (WAXD), Fourier transform infrared spectroscopy, and small‐angle X‐ray scattering (SAXS). The extrusion‐cast polyamide‐11 films exhibited elevations in the glass‐transition and cold‐crystallization temperatures with a constant crystallinity and a constant melting point during aging under room conditions (20–26 °C and 20–31% relative humidity). WAXD and SAXS suggested that chain‐folded lamellae of coexisting α‐ and β‐crystals existed in all the stretched polyamide‐11 films. WAXD pole figures indicated that hydrogen bonds in the hydrogen‐bonded sheets of these two crystalline forms apparently formed between antiparallel chain molecules. The unit cell parameters [a = 9.52 Å, b = 5.35 Å, c = 14.90 Å (chain axis), α = 48.5°, β = 90°, and γ = 74.7° for a triclinic α form and a = 9.52 Å, b = 14.90 Å (chain axis), c = 4.00 Å, α = 90°, β = 67.5°, and γ = 90° for a monoclinic β form] for polyamide‐11 crystals were proposed according to the results of this study and the results of previous investigators. The unit cell parameters of the stretched extrusion‐cast polyamide‐11 films varied, depending on the stretching conditions (the stretch temperature and stretch ratio). As the stretch temperature and stretch ratio were increased, the crystal became more similar to the form described previously and was accompanied by an increase in the long spacing of crystalline lamellae. Annealing the stretched films in a boiling 20% formic acid solution made slightly more perfected crystals. The hydrogen‐bonding α(010) + β(002) planes, which are nearly parallel to both amide group planes and zigzag methylene sequence planes of the biaxially stretched films were found to be parallel to the film surface. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2624–2640, 2002     

Structural and mechanical behavior of nylon 6 films part I. Identification and stability of the crystalline phases

The crystalline phase of polyamide 6 (otherwise nylon 6) films produced following various physical treatments is investigated by means of thermal analysis, X‐ray diffraction, and infrared spectroscopy. A recently published procedure for treating infrared spectra of multicomponent compounds without a priori knowledge of the individual component spectra allowed us to perform a semiquantitative analysis of the structural changes upon annealing, including data from drawn samples. Melt‐cast films display a mesomorphic state that is thermally stable up to about 120 °C. This structure partly reorganizes into the stable monoclinic α form above 120 °C. Films in major γ form produced by iodine treatment are thermally stable up to 200 °C. Films in major α form are also prepared by superheated water treatment. No evidence is given for a Brill transition about 170 °C. This is an important fact for further understanding of the drawing behavior of PA6 at temperatures above and below this domain. The mesomorphic phase can hardly be separated from the amorphous component both from X‐ray and infrared analysis. However, scanning calorimetry, which is often criticized due to possible reorganization of unstable species during the heating scan, turned out to be a very useful technique. Indeed, recrystallization from the amorphous phase or improvement of ordering from the mesomorphic state both result in exothermic effects in quite different temperature domains that allow to discriminate the two phenomena. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 484–495, 2001     

Quick water-responsive shape memory hybrids with cellulose nanofibers

A type of quick water-responsive shape memory hybrids is fabricated by introducing cellulose nanofibrous mats as the filler in a polymeric matrix. Cellulose nanofibrous mats are obtained through hydrolyzing electrospun cellulose acetate (CA) nanofibers, then casted in thermoplastic polyurethane (TPU) solution to form the hybrids. The quick shape memory behavior of the formed hybrids is demonstrated using dynamic mechanical analysis (DMA) and stress–strain cyclic test. According to a predetermined protocol, the hybrids present desirable shape fixation and recovery, and the elastic modulus (E′) is shown to be responsive promptly and reversibly against drying and wetting cycle. Shape memory mechanism of the hybrids involves the reversible and competitive hydrogen bonds within cellulose before and after water immersion as well as the entropy elasticity of the TPU matrix. This study can pave a way to design novel smart materials by facile methods through incorporating natural nanomaterials as water sensitive fillers. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 767–775     

Effect of side‐chain length on the electrospinning of perfluorosulfonic acid ionomers

The effect of the side‐chain length (short side chain and long side chain, SSC and LSC, respectively) of perfluorosulfonic acid (PFSA) ionomers on the properties of nanofibers obtained by electrospinning ionomer dispersions in high dielectric constant liquids has been investigated with a view to obtaining electrospun webs as components of fuel cell membranes. Ranges of experimental conditions for electrospinning LSC and SSC PFSAs have been explored, with a scoping of solvents, carrier polymer and PFSA ionomer concentrations, and carrier polymer molecular weight. Under optimal conditions, the electrospun mats derived from SSC and from LSC PFSA show distinct fiber dimensions that arise from the different chain lengths of the respective ionomers. Enhanced interchain interactions in SSC PFSA with low equivalent weight compared to LSC PFSA result in a considerably lower average fiber diameter and a markedly narrower fiber size distribution. The proton conductivity of nanofiber mats of SSC and LSC PFSA with equivalent weights of 830 and 900 g mol^?1, respectively, are 102 and 58 mS cm^?1 at 80°C and 95% relative humidity. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Structure and molecular conformation of tussah silk fibroin films: Effect of heat treatment

Structural changes of tussah (Antheraea pernyi) silk fibroin films induced by heat treatment were studied as a function of the treatment temperature in the range 200–250°C. The DSC curve of tussah films with α-helix molecular conformation displayed characteristic endo and exo peaks at 216 and 226°C, respectively. These peaks first weakened and then completely disappeared after heating at 230°C. Accordingly, the TMA thermal shrinkage at 206°C disappeared when the films were heated at 230°C. The onset of weight loss was monitored at 210°C by means of TG measurements. X-ray diffraction profiles gradually changed from α-helix to β-sheet crystalline structure as the treatment temperature increased from 200 to 250°C. On raising the heating temperature above 200°C, the intensity of IR and Raman bands characteristic of β-sheet conformation increased in the whole ranges of amide and skeletal modes. The sample treated at 200°C showed a spectral pattern intermediate between α-helix and β-sheet molecular conformation. The IR marker band for random coil structure, still detectable at 200°C, disappeared at higher treatment temperatures. Spectral changes attributable to the onset of thermal degradation appeared at 230°C. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 841–847, 1997     

Highly organosoluble and flexible polyimides with color lightness and transparency based on 2,2‐bis[4‐(2‐trifluoromethyl‐4‐aminophenoxy)‐3,5‐dimethylphenyl]propane

A new diamine containing isopropylidene, methyl substituted arylene ether, and trifluoromethyl groups, 2,2‐bis[4‐(2‐trifluoromethyl‐4‐aminophenoxy)‐3,5‐dimethylphenyl]propane (BTADP), was synthesized and used in preparation of a series of polyimides by direct polycondensation with various aromatic tetracarboxylic dianhydrides in N, N‐dimethylacetamide (DMAc). All polymers derived from diamine (BTADP) with trifluoromethyl substituents were highly organosoluble in the solvents, like N‐methyl‐2‐pyrrolidinone (NMP), N,N‐dimethylacetamide, N,N‐dimethylformamide (DMF), pyridine, chloroform, tetrahydrofuran (THF), dimethyl sulfoxide (DMSO), dichloromethane, cyclohexanone, and γ‐butyrolactone at room temperature or upon heating at 70 °C. Inherent viscosities of the polyimides were found to range between 0.58 and 0.97 dL·g^?1. These polyimides had glass transition temperatures between 256 and 307 °C, and their 10% mass loss temperatures ranged from 440 to 462 °C and 421 to 443 °C under nitrogen and air, respectively. These polyimides had low dielectric constants in the range of 2.84–3.09. All the polyimides could be cast into films from DMAc solutions and were thermally converted into color lightness, optically transparent, flexible, and tough polyimides. The polyimide films had a tensile strength in the range of 83–97 MPa and a tensile modulus in the range of 2.0–2.2 GPa. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5766–5774, 2004     

Structure and molecular conformation of tussah silk fibroin films treated with water–methanol solutions: Dynamic mechanical and thermomechanical behavior

The thermal response of tussah (Antheraea pernyi) silk fibroin films treated with different water–methanol solutions at 20°C was studied by means of dynamic mechanical (DMA) and thermomechanical (TMA) analyses as a function of methanol concentration and treatment time. The DMA curves of α-helix films (treated with ≥80% v/v methanol for 2 min and 100% methanol for 30 min) showed the sharp fall of storage modulus at about 190°C, and the loss peak in the range 207–213°C. The TMA curves were characterized by a thermal shrinkage at 209–211°C, immediately followed by an abrupt extension leading to film failure. Both storage and loss modulus curves significantly shifted upwards for β-sheet films, obtained by treatment with ≤60% methanol for 30 min. The loss peak exhibited a maximum at 236°C. Accordingly, the TMA shrinkage at above 200°C disappeared. The films broke beyond 330°C, failure being preceded by a broad contraction step. Intermediate DMA and TMA patterns were observed for the other solvent-treated films. The loss peak shifted to higher temperature (219–220°C), and a minor loss modulus component appeared at about 230°C. This coincided with the onset of a plateau region in the storage modulus curve. The TMA extension–contraction events in the range 200–300°C weakened, and the samples displayed a final broad contraction (peak temperature 326–338°C) before breaking. The DMA and TMA response of these films was attributed to partial annealing by solvent treatment, which resulted in the formation of nuclei of β-sheet crystallization within the film matrix. The increased thermal stability was probably due to the small β-sheet crystals formed, which acted as high-strength junctions between adjacent random coil and α-helix domains. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2717–2724, 1998     

Sharp Hydrophilicity Switching and Conformality on Nanostructured Surfaces Prepared via Initiated Chemical Vapor Deposition (iCVD) of a Novel Thermally Responsive Copolymer

A novel thermally responsive copolymer p(NIPAAm‐co‐DEGDVE) is synthesized using the substrate independent method of iCVD and exhibits a sharp lower critical solution temperature (LCST) transition centered at ≈28.5 ± 0.3 °C determined via quartz crystal microbalance measurements with dissipation monitoring (QCM‐D). Swelling with water below the LCST produces a reversible change of ≈3× in film thickness. The layer is conformal on nanostructured surfaces including MWCNT forests and electrospun nanofiber mats. Modified planar substrates exhibit ≈30°change in static contact angle over the LCST, while through conformal coating on nanostructured substrates changes in static contact angle up to 135° are achieved. Additionally, coated surfaces exhibit temperature sensitive BSA adsorption measured by QCM‐D and is reversible as shown through fluorescence imaging of a coated electrospun nanofiber mat.