Simple synthesis,photophysics, and electroluminescent properties of poly[2,7‐bis(4‐tert‐butylstyryl)fluorene‐9, 9‐diyl‐alt‐alkane‐α,ω‐diyl]

A simple synthetic route was used for the synthesis of a novel series of alternating copolymers based on substituted 2,7‐distyrylfluorene bridged through alkylene chains. First, 2,7‐dibromofluorene was reacted with 2 equiv of butyllithium, and this was followed by a treatment with 1 equiv of α,ω‐dibromoalkane to yield the intermediate, poly(2,7‐dibromofluorene‐9,9‐diyl‐alt‐alkane‐α,ω‐diyl). ( 1 ) Heck coupling of the latter with 1‐tert‐butyl‐4‐vinylbenzene afforded the target, poly[2,7‐bis(4‐tert‐butylstyryl)fluorene‐9,9‐diyl‐alt‐alkane‐α,ω‐diyl] ( 2 ). The two versions of 2 ( 2a and 2b which have hexane and decane, respectively, as alkane groups) were readily soluble in common organic solvents. Their glass‐transition temperature was relatively low (52 and 87 °C). An intense blue photoluminescence emission with maxima at about 408 and 409 nm was observed in tetrahydrofuran solutions, whereas thin films exhibited an orange emission with maxima at 569 and 588 nm. Very large redshifts of the photoluminescence maxima and Stokes shifts in thin films indicated strong aggregation in the solid state. Both polymers oxidized and reduced irreversibly. Single‐layer light‐emitting diodes with hole‐injecting indium tin oxide and electron‐injecting aluminum electrodes were fabricated. They emitted orange light with external electroluminescence efficiencies of 0.52 and 0.36% photon/electron, as determined in light‐emitting diodes made of 2a and 2b , with alkylenes of (CH₂)₆ and (CH₂)₁₀, respectively. An increase in the external electroluminescence efficiency up to 1.5% was reached in light‐emitting diodes made of polymer blends consisting of 2a and poly(9,9‐dihexadecylfluorene‐2,7‐diyl), which emitted blue‐white light. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 809–821, 2007.     

Synthesis,characterization, photo‐induced alignment,and surface orientation of poly(9,9‐dioctylfluorene‐alt‐azobenzene)s

Three types of bi‐functionalized copolymers ( P1FAz , P2FAz , and P3FAz ) with different numbers of fluorene units and an azobenzene unit were synthesized and characterized using UV–vis and polarized absorption spectroanalysis. The trans‐cis photoisomerization was conformed under 400 nm light irradiation for all copolymers in chloroform. However, in the film state, only the trans‐cis photoisomerization occurred by mono‐fluorene attached copolymer poly[(9,9‐di‐n‐octylfluorenyl‐2,7‐diyl)‐alt‐4,4′‐azobenzene)] ( P1FAz ). Photo‐induced alignment was achieved using the P1FAz film after irradiation with linear polarized 400 nm light and subsequent annealing at 60 °C. Surface orientation of a spin‐coating film of poly(9,9‐didodecylfluorene) ( F12 ) was achieved using the photo‐induced alignment layer of the P1FAz film after annealing at 90 °C. The photo‐induced alignment layer of P1FAz has potential application to the surface orientation technique for appropriate polymers, which will be useful for the fabrication of optoelectronics devices. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Phenothiazine‐S,S‐dioxide‐ and fluorene‐based light‐emitting polymers: Introduction of e−‐deficient S,S‐dioxide into e−‐rich phenothiazine

A novel series of poly(10‐hexyl‐phenothiazine‐S,S‐dioxide‐3,7‐diyl) and poly(9,9′‐dioctyl‐fluorene‐2,7‐diyl‐alt‐10‐hexyl‐3,7‐phenothiazine‐S,S‐dioxide) (PFPTZ‐SS) compounds were synthesized through Ni(0)‐mediated Yamamoto polymerization and Pd(II)‐catalyzed Suzuki polymerization. The synthesized polymers were characterized by ¹H NMR spectroscopy and elemental analysis and showed higher glass transition temperatures than that of pristine polyfluorene. In terms of photoluminescence (PL), the PFPTZ‐SS compounds were highly fluorescent with bright blue emissions in the solid state. Light‐emitting devices were fabricated with these polymers in an indium tin oxide/poly(3,4‐ethylene dioxythiophene):poly(styrene sulfonate)/polymer/Ca/Al configuration. The electroluminescence (EL) of the copolymers differed from the PL characteristics: the EL device exhibited a redshifted greenish‐blue emission in contrast to the blue emission observed in the PL. Additionally, this unique phenothiazine‐S,S‐dioxide property, triggered by the introduction of an electron‐deficient SO₂ unit into the electron‐rich phenothiazine, gave rise to improvements in the brightness, maximum luminescence intensity, and quantum efficiency of the EL devices fabricated with PFPTZ‐SS. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1236–1246, 2007     

Quantifying the role of interfacial width on intermolecular charge recombination in block copolymer photovoltaics

Block copolymers have the potential to control the interfacial and mesoscopic structure in the active layer of organic photovoltaics and consequently enhance device performance beyond systems which rely on physical mixtures. When utilized as the active layer, poly(3‐hexylthiophene‐2,5‐diyl)‐block‐poly((9,9‐bis‐(2‐octyldodecyl)fluorene‐2,7‐diyl)‐alt‐(4,7‐di(thiophene‐2‐yl)?2,1,3‐benzothiadiazole)?5′,5″‐diyl) donor–acceptor block copolymers have recently demonstrated 3% power conversion efficiencies in devices. Nevertheless, the role of the interfacial structure on charge transfer processes remains unclear. Using density functional theory, we examined charge transfer rate constants in model interfaces of donor–acceptor block copolymers. Our results demonstrate that intermolecular charge recombination can depend on the interfacial breadth, where sharp interfaces (ca. 1 nm) suppress intermolecular charge recombination by orders of magnitude. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1224–1230     

Synthesis and electroluminescent properties of fluorene‐based copolymers containing electron‐withdrawing thiazole derivatives

We synthesized two fluorene‐based copolymers poly[(2,5‐bis(4‐hexylthiophen‐2‐yl)thiazolo[5,4‐day]thiazole‐5,5′‐diyl)‐alt‐(9,9′‐dioctylfluorene‐2,7‐diyl)] ( PF‐TTZT), and poly[(5,5′‐bis(4‐hexylthiophen‐2‐yl)‐2,2′‐bithiazole‐5,5′‐diyl)‐alt‐(9,9′‐dioctylfluorene‐2,7‐diyl)] (PF‐TBTT), which contain the electron‐withdrawing moieties, thiazolothiazole, and bithiazole, respectively. Through electrochemical studies, we found that these two polymers exhibit stable reversible oxidation and reduction behaviors. Moreover, the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of PF‐TBTT are lower than those of PF‐TTZT, and the bandgap of PF‐TBTT is smaller than that of PF‐TTZT. Thus the bithiazole moiety in PF‐TBTT is more electron‐withdrawing than the thiazolothiazole moiety in PF‐TTZT. Light‐emitting devices with indium tin oxide (ITO)/poly(3,4‐ethylene dioxythiophene):poly(styrenesulfonate)(PEDOT)/polymer/bis(2‐methyl‐8‐quinolinato)‐4‐phenylphenolate aluminum (BAlq)/LiF/Al configurations were fabricated. The performance of the PF‐TBTT device was found to be almost three times better than that of the PF‐TTZT device, which is because electron injection from the cathode to PF‐TBTT is much easier than for PF‐TTZT. We also investigated the planarity and frontier orbitals of the electron donor‐acceptor (D‐A) moieties with computational calculations using ab initio Hartree–Fock with the split‐valence 6‐31G* basis set. These calculations show that TBTT has a more nonplanar structure than TTZT and that the bithiazole moiety is more electron‐withdrawing than thiazolothiazole. These calculations are in good agreement with the experimental results. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7148–7161, 2008     

Synthesis and properties of conjugated copolycondensates consisting of carbazole‐2,7‐diyl and fluorene‐2,7‐diyl

Carbazole and fluorene‐based random and alternating copolycondensates were synthesized to develop high‐performance blue light‐emitting polymers by improving electron injection ability of poly(N‐aryl‐2,7‐carbazole)s that showed intense blue electroluminescence (EL) with good hole‐injection and ‐transport ability. These copolycondensates absorbed light energy at about λ_max = 390 nm in CHCl₃ and 400 nm in film state, and fluoresced at about λ_max = 417 nm in CHCl₃ and 430 nm in the thin film state. Energy gaps between highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) of them were about 2.9 eV, and the energy levels of LUMO situated lower than that of corresponding polycarbazole. Polymer light‐emitting diode devices having configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene)‐poly(styrenesulfonate)/polymer/CsF/Al using the copolycondensates, poly(N‐arylcarbazole‐2,7‐diyl), and poly(9,9‐dialkylfluorene‐2,7‐diyl), emitted bluish EL at operating voltages lower than 7 V. The device embedded the random copolycondensate showed notably higher performance with maximum luminance of 31,200 cd m^?2 at 11.0 V, and the current efficiencies observed under operating voltages lower than 7 V were higher than those of the other devices. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Design and synthesis of 9,9‐dioctyl‐9H‐fluorene based electrochromic polymers

Two novel heterocycle‐fluorene‐heterocycle monomers, 2,2′‐(9,9‐dioctyl‐9H‐fluorene‐2,7‐diyl)dithiophene (Th‐F‐Th) and 5,5′‐(9,9‐dioctyl‐9H‐fluorene‐2,7‐diyl)bis(2,3‐dihydrothieno[3,4‐b][1,4]dioxine) (EDOT‐F‐EDOT), were synthesized via Stille coupling reaction and electropolymerized to form corresponding polymers P(Th‐F‐Th) and P(EDOT‐F‐EDOT). Furthermore, the optoelectronic properties of the obtained monomers and polymers were explored using cyclic voltammetry (CV), UV–vis, and emission spectra and in situ spectroelectrochemical techniques. The band gap values of monomers calculated by DFT were 3.75 eV for EDOT‐F‐EDOT and 4.03 eV for Th‐F‐Th, while that of P(EDOT‐F‐EDOT) and P(Th‐F‐Th) were brought down to 1.70 and 2.10 eV, respectively. Both polymers exhibited excellent redox activity and electrochromic performance. P(EDOT‐F‐EDOT) exhibited a maximum optical contrast of 25.8% at 500 nm in visible region with a response time of 1.2 s. In addition, the coloration efficiency of P(EDOT‐F‐EDOT) was calculated to be 220 cm² C^?1. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 325–334     

Molecular orientation and composition at the surface of spin‐coated polyfluorene:Fullerene blend films

The surface composition in spin‐coated films of polyfluorene:fullerene blends was determined quantitatively by near‐edge X‐ray absorption fine structure (NEXAFS) spectroscopy. By comparing partial and total electron yield spectra, we found vertical compositional differences in the surface region. Furthermore, the orientation of the polymer chains was investigated by variable‐angle NEXAFS. Blend films of poly[(9,9‐dioctylfluorenyl‐2,7‐diyl)‐co‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole] with [6,6]‐phenyl‐C61‐butyric acid methyl ester in two different blend ratios were studied. Results showed polymer enrichment of the surfaces for films with a polymer:fullerene weight ratio of 20:80 and of 50:50, spin‐coated from both chlorobenzene and chloroform solutions. The angular dependence of the NEXAFS spectra of the pure polymer films showed a preferential plane‐on orientation, which was slightly stronger in the subsurface region than at the surface. In blend films, this orientational preference was less pronounced and the difference between surface and subsurface vanished. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Fluorene‐based alternating polymers containing electron‐withdrawing bithiazole units: Preparation and device applications

We report here the synthesis via Suzuki polymerization of two novel alternating polymers containing 9,9‐dioctylfluorene and electron‐withdrawing 4,4′‐dihexyl‐2,2′‐bithiazole moieties, poly[(4,4′‐dihexyl‐2,2′‐bithiazole‐5,5′‐diyl)‐alt‐(9,9‐dioctylfluorene‐2,7‐diyl)] (PHBTzF) and poly[(5,5′‐bis(2″‐thienyl)‐4,4′‐dihexyl‐2,2′‐bithiazole‐5″,5″‐diyl)‐alt‐(9,9‐dioctylfluorene‐2,7‐diyl)] (PTHBTzTF), and their application to electronic devices. The ultraviolet–visible absorption maxima of films of PHBTzF and PTHBTzTF were 413 and 471 nm, respectively, and the photoluminescence maxima were 513 and 590 nm, respectively. Cyclic voltammetry experiment showed an improvement in the n‐doping stability of the polymers and a reduction of their lowest unoccupied molecular orbital energy levels as a result of bithiazole in the polymers' main chain. The highest occupied molecular orbital energy levels of the polymers were ?5.85 eV for PHBTzF and ?5.53 eV for PTHBTzTF. Conventional polymeric light‐emitting‐diode devices were fabricated in the ITO/PEDOT:PSS/polymer/Ca/Al configuration [where ITO is indium tin oxide and PEDOT:PSS is poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonic acid)] with the two polymers as emitting layers. The PHBTzF device exhibited a maximum luminance of 210 cd/m² and a turn‐on voltage of 9.4 V, whereas the PTHBTzTF device exhibited a maximum luminance of 1840 cd/m² and a turn‐on voltage of 5.4 V. In addition, a preliminary organic solar‐cell device with the ITO/PEDOT:PSS/(PTHBTzTF + C₆₀)/Ca/Al configuration (where C₆₀ is fullerene) was also fabricated. Under 100 mW/cm² of air mass 1.5 white‐light illumination, the device produced an open‐circuit voltage of 0.76 V and a short‐circuit current of 1.70 mA/cm². The fill factor of the device was 0.40, and the power conversion efficiency was 0.52%. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1845–1857, 2005     

Donor–acceptor rod–coil block copolymers comprising poly[2,7‐(9,9‐dihexylfluorene)‐alt‐bithiophene] and fullerene as compatibilizers for organic photovoltaic devices

The successful synthesis is described for a donor–acceptor rod–coil block copolymer comprising blocks of poly[2,7‐(9,9‐dihexylfluorene)‐alt‐bithiophene] (F6T2) and polystyrene functionalized with fullerene (PS(C₆₀)) (F6T2‐b‐PS(C₆₀)). This new material was obtained by combining Suzuki polycondensation with radical addition fragmentation chain transfer. The block copolymer was characterized by nuclear magnetic resonance, gel permeation chromatography, and optical spectroscopy methods. Photophysical data for (F6T2‐b‐PS(C₆₀)) and a related block copolymer (F6T2‐b‐PS(PCBM)) (PCBM, phenyl‐C61‐butyric acid methyl ester) are reported and their performance as compatibilizers in bulk heterojunction organic solar cells is assessed. It is demonstrated that the addition of the rod–coil block copolymers to the active layer extends the operational stability of organic photovoltaic devices. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 888–903     

Characterization of two‐ and three‐photon absorption of polyfluorene derivatives

Fluorene‐based polymer derivatives are promising materials for organic electronic devices because of their photoluminescence and electroluminescence, good film‐forming ability, and favorable chemical and thermal properties. Although optical properties of polyfluorene have already been reported, most of the studies focused on the linear optical properties, whereas nonlinear optical characteristics have only recently received more detailed attention. Here, we report on two polyfluorene derivatives, poly(9,9′‐n‐dihexyl‐2,7‐fluorenediyl) (LaPPS 10) and poly(9,9′‐n‐dihexyl‐2,7‐fluorene‐diyl‐vinylene) (LaPPS 38), which present intense nonlinear absorption and fluorescence. Two‐photon absorption cross‐section properties of both polymers were characterized in the spectral range from 500 nm up to 900 nm, reaching peak values around 2000 Göppert Mayer units. Optical limiting behavior and two‐photon‐induced fluorescence of both polymers have also been investigated. Furthermore, the first molecular hyperpolarizability of the polymers was also studied using hyper‐Rayleigh scattering. In addition, the three‐photon absorption (3PA) spectra of both materials were also investigated, and 3PA cross‐section values in the order of 1 × 10^?78 cm⁶ s² photon^?2 were observed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 747–754     

Photodegradation‐induced photoluminescence behaviors of π‐conjugated polymers upon the doping of organometallic triplet emitters

The different effects on the photodegradation‐induced photoluminescence (PL) of π‐conjugated polymeric thin films upon the doping of Ir(III) containing triplet emitters in ambient conditions at room temperature were investigated. In this study, we prepared spin‐coated thin films using three different polymer matrices including poly(9‐vinylcarbazole) (PVK), poly[9,9‐bis(2‐ethylhexyl)fluorene‐2,7‐diyl] (PF2/6), and poly[2‐(5′‐cyano‐5′‐methyl‐hexyloxy)‐1,4‐phenylene] (CNPPP) derivatives doped with Ir(III) containing triplet emitters: Ir(III) bis[(4,6‐fluorophenyl)‐pyridinato‐N,C²′] picolinate (FIrpic), or Ir(III)fac‐tris(2‐phenylpyridine) (Ir(ppy)₃), or Ir(III)bis(2‐(2′‐benzothienyl) pyridinato‐N‐acetylacetonate) (Ir(btp)₂acac). Using the doped films, and their neat films, on quartz substrates, the UV‐Visible absorption (UV‐Vis) and PL spectra were recorded under continuous illumination with the excitation wavelengths at the absorption maxima of the corresponding matrix polymers. The dopant effects on the photodegradation‐induced PL were extracted from the kinetic data obtained from the doped films by subtracting the mutual degradation kinetics of their corresponding neat films. The obtained dopant effects show a strong correlation between the photo‐induced PL degradation and the exciton migration behaviors. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2395–2403, 2008     

Synthesis of novel π‐conjugating polymers based on dibenzothiophene

Novel π‐conjugating polymers based on dibenzothiophene were synthesized with a novel dibenzothiophene derivative, 2,8‐bis(4,4,5,5‐tetramethyl‐1,3,2‐dioxaborolan‐2‐yl)dibenzothiophene ( 1 ), prepared from dibenzothiophene. The Suzuki coupling polycondensation of 1 with 2,7‐dibromo‐9,9‐dioctylfluorene, 3,6‐dibromo‐9‐octylcarbazole, or 1,4‐dibromo‐2,5‐dioctyloxybenzene afforded the corresponding dibenzothiophene‐based polymers. The measurements of photoluminescence indicated that all these polymers exhibited blue emission in solution. The copolymer containing dibenzothiophene and 9,9‐dioctylfluorene units exhibited higher thermal stability than poly[(9,9‐dioctylfluorene‐2,7‐diyl)], although the quantum yield of copolymer was lower than that of poly[(9,9‐dioctylfluorene‐2,7‐diyl)]. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1521–1526, 2003     

Effect of hexyl substituent groups on photophysical and electrochemical properties of the poly[(9,9‐Dioctyluorene)−2,7‐diyl‐alt‐(4,7‐bis (3‐Hexylthien‐5‐Yl)−2,1,3‐Benzothiadiazole)−2′,2″‐diyl]

The effect of the presence of hexyl group in thiophene on the photophysical and electrochemical properties of poly[(9,9‐dioctyluorene)?2,7‐diyl‐alt‐(4,7‐bis(3‐hexylthien‐5‐yl)?2,1,3‐benzothiadiazole)?2′,2″‐diyl] (F8TBT) is investigated. The copolymers present electron donor–acceptor architecture and are synthesized by Suzuki coupling reaction. The UV/Vis spectra show absorption maximum in the wavelength range of blue and orange, which are associated with different segments of the polymer backbone. Addition of hexyl substituent groups has a positive effect on the molar absorptivity and increases the emission and absorption intensities due to fluorene and thiophene‐benzothiadiazole‐thiophene (TBT) units, although an increment in the bandgap is observed. Cyclic voltammetry study of the polymer films reveal irreversible reduction and oxidation processes of the TBT units in the polymer chain and the HOMO and LUMO energy levels suggest ambipolar character for the polymers, while the electrochemical bandgaps are consistent with the absorbance measurements. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1975–1982     

Synthesis of new polyfluorene copolymers with a comonomer containing triphenylamine units and their applications in white‐light‐emitting diodes

Novel conjugated polyfluorene copolymers, poly[9,9‐dihexylfluorene‐2,7‐diyl‐co‐(2,5‐bis(4′‐diphenylaminostyryl)‐phenylene‐1,4‐diyl)]s (PGs), have been synthesized by nickel(0)‐mediated polymerization from 2,7‐dibromo‐9,9‐dihexylfluorene and 1,4′‐dibromo‐2,5‐bis(4‐diphenylaminostyryl)benzene with various molar ratios of the monomers. Because of the incorporation of triphenylamine (TPA) moieties, PGs exhibit much higher HOMO levels than the corresponding polyfluorene homopolymers and are able to facilitate hole injection into the polymer layer from the anode electrode in light‐emitting diodes. Conventional polymeric light‐emitting devices with the configuration ITO/PEDOT:PSS/polymer/Ca/Al have been fabricated. A light‐emitting device produced with one of the PG copolymers (PG10) as the emitting layer exhibited a voltage‐independent and stable bluish‐green emission with color coordinates of (0.22, 0.42) at 5 V. The maximum brightness and current efficiency of the PG10 device were 3370 cd/m² (at 9.6 V) and 0.6 cd/A, respectively. To realize a white polymeric light‐emitting diode, PG10 as the host material was blended with 1.0 wt % of a red‐light‐emitting polymer, poly[9,9‐dioctylfluorene‐2,7‐diyl‐alt‐2,5‐bis(2‐thienyl‐2‐cyanovinyl)‐1‐(2′‐ethylhexyloxy)‐4‐methoxybenzene‐5′,5′‐diyl] (PFR4‐S), and poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV). The device based on PG10:PFR4‐S showed an almost perfect pure white electroluminescence emission, with Commission Internationale de l'Eclairage (CIE) coordinates of (0.33, 0.36) at 8 V; for the PG10:MEH‐PPV device, the CIE coordinates at this voltage were (0.30, 0.40) with a maximum brightness of 1930 cd/m². Moreover, the white‐light emission from the PG10:PFR4‐S device was stable even at different driving voltages and had CIE coordinates of (0.34, 0.36) at 6 V and (0.31, 0.35) at 10 V. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1199–1209, 2007     

Arylamino‐functionalized fluorene‐ and carbazole‐based copolymers: Color‐tuning their CdTe nanocrystal composites from red to white

Four alternating arylamino‐functionalized copolymers were synthesized in a Suzuki copolymerization applying 4, 4′‐(2,7‐dibromo‐9H‐fluorene‐9,9‐diyl)dianiline, 4,4′‐(2,7‐dibromo‐9H‐fluorene‐9,9‐diyl)bis(N,N‐diphenylaniline), 4‐(3,6‐dibromo‐9H‐ carbazol‐9‐yl)aniline and 4‐(3,6‐dibromo‐9H‐carbazol‐9‐yl)‐N,N‐diphenylaniline in combination with 2,2′‐(9,9‐dioctyl‐9H‐fluorene‐2,7‐diyl)bis(1,3,2‐dioxaborinane). The resulting novel alternating copolymers were fully characterized. The copolymers revealed blue light emission and wide optical bandgaps of at least 2.93 eV for the fluorene‐based and 3.07 eV for the carbazole‐based polymers. The amino‐functions allow to tie semiconducting CdTe nanocrystals (NCs) and to synthesize a series of composites with CdTe NCs. Moreover, tuning the emission color over a wide range by tying these CdTe NCs results in a facile preparation of organic–inorganic semiconductor composites with emission colors “à la carte.” © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and properties of fluorene‐based fluorinated polymers

Fluorene‐based polymers containing various fluorinated benzene (fluorobenzene, p‐difluorobenzene, and tetrafluorobenzene) moieties were synthesized. In addition, perfluorooctylation of poly‐[(9,9‐dioctylfluorene‐2,7‐diyl)‐co‐(fluorene‐2,7‐diyl)] was carried out to afford fluorene‐based polymers with perfluorooctyl moiety at the 9‐position on the fluorene ring. To evaluate the effect of fluorine moiety, polymers containing nonfluorinated benzene moieties and nonfluorinated octyl groups were synthesized. The photoluminescence measurements indicated that all these polymers exhibited blue emission in solution, but a polymer containing a perfluorooctyl group did not emit in the film state. Polymers containing various fluorinated benzene moieties showed higher fluorescence quantum yields and thermal stability than those containing nonfluorinated benzene. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3143–3150, 2001     

Enhanced efficiency of polyfluorene derivatives: Organic–inorganic hybrid polymer light‐emitting diodes

Two novel organic–inorganic hybrid polyfluorene derivatives, poly{(9,9′‐dioctyl‐2,7‐fluorene)‐co‐(9,9′‐di‐POSS‐2,7‐fluorene)‐co‐[2,5‐bis(octyloxy)‐1,4‐phenylene]} (PFDOPPOSS) and poly{(9,9′‐dioctyl‐2,7‐fluorene)‐co‐(9,9′‐di‐POSS‐2,7‐fluorene)‐co‐bithiophene} (PFT2POSS), were synthesized by the Pd‐catalyzed Suzuki reaction of polyhedral oligomeric silsesquioxane (POSS) appended fluorene, dioctyl phenylene, and bithiophene moieties. The synthesized polymers were characterized with ¹H NMR spectroscopy and elemental analysis. Photoluminescence (PL) studies showed that the incorporation of the POSS pendant into the polyfluorene derivatives significantly enhanced the fluorescence quantum yields of the polymer films, likely via a reduction in the degree of interchain interaction as well as keto formation. Additionally, the blue‐light‐emitting polyfluorene derivative PFDOPPOSS showed high thermal color stability in PL. Moreover, single‐layer light‐emitting diode devices of an indium tin oxide/poly(3,4‐ethylene dioxythiophene):poly(styrene sulfonate)/polymer/Ca/Al configuration fabricated with PFDOPPOSS and PFT2POSS showed much improved brightness, maximum luminescence intensity, and quantum efficiency in comparison with devices fabricated with the corresponding pristine polymers PFDOP and PFT2. In particular, the maximum external quantum efficiency of PFT2POSS was 0.13%, which was twice that of PFT2 (0.06%), and the maximum current efficiency of PFT2POSS was 0.38 cd/A, which again was twice that of PFT2 (0.19 cd/A). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2943–2954, 2006     

Reactive intermediates in the initiation step of the photo‐oxidation of MDMO‐PPV

Because oxygen cannot be fully eliminated from organic solar cells, the occurrence of oxidative photo‐degradation of the device in operating conditions has to be considered. Polyphenylene‐vinylene‐based photovoltaic devices have a short lifetime that currently limits their applications. In this article, we focus on various transient species that are potentially involved in the initiation step of the photo‐oxidation of poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylenevinylene] (MDMO‐PPV). The role of the transient species was investigated by a combination of quenching and sensitization experiments. Complementary information was obtained by transient absorption spectroscopy. Results evidenced the fact that ¹O₂ was not the principal reactive intermediate involved in the photo‐oxidation of MDMO‐PPV. This result was in contradiction with previous reports. It was shown that the MDMO‐PPV^?+ radical cation was generated after excitation. The presence of oxygen and the photo‐aging favored the formation of the radical cation, suggesting that oxygen and photoproducts act as electron acceptors. The charged radicals formed are likely to evolve and give radicals that initiate the oxidation of the polymer by abstraction of the labile hydrogen in α position of the ether function and by addition on the double bonds. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6044–6052, 2009     

Deep‐blue light‐emitting polyfluorenes containing spiro[fluorene‐9,9′‐thioxanthene‐S,S‐dioxide] isomers

Blue light‐emitting polyfluorenes, PPF‐FSOs and PPF‐SOFs were synthesized via introducing spiro[fluorene‐9,9′‐thioxanthene‐S,S‐dioxide] isomers (2,7‐diyl and 2′,7′‐diyl) (FSO/SOF) into the poly[9,9‐bis(4‐(2‐ethylhexyloxy) phenyl)fluorene‐2,7‐diyl] (PPF) backbone, respectively. With the increasing contents of FSO and SOF moieties, the absorption and PL spectra of PPF‐FSOs show slight red shift, while that of PPF‐SOFs exhibit blue shift, respectively. The HOMO and LUMO levels reduce gradually with increasing SOF unit in PPF‐SOFs. The polymers emit blue light peaked around 430–445 nm and show an excellent spectral stability with the variation in current densities. The distinctly narrowing EL spectra were observed with the incorporation of isomers in the polymers. The full width at half maximum reduced by 15 nm for PPF‐SOFs, resulting in a blue shift with the CIE coordinates from (0.16, 0.11) to (0.16, 0.08). With a device configuration of ITO/PEDOT:PSS/EML/CsF/Al, a maximum luminance efficiency (LE_max) of 2.00 cd A^?1, a maximum external quantum efficiency (EQE_max) of 3.76% with the CIE coordinates of (0.16, 0.08) for PPF‐SOF15 and a LE_max of 1.68 cd A^?1, a EQE_max of 2.38% with CIE (0.16, 0.12) for PPF‐FSO10 were obtained, respectively. The result reveals that spiro[fluorene‐9,9′‐thioxanthene‐S,S‐dioxide] isomers are promising blocks for deep‐blue light‐emitting polymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 2332–2341