Novel polyamidoamine‐based hydrogel with an innovative molecular architecture as a Co2+‐, Ni2+‐, and Cu2+‐sorbing material: Cyclovoltammetry and extended X‐ray absorption fine structure studies

An amphoteric polyamidoamine (PAA)‐based hydrogel, named INT‐PAA1, with a novel molecular architecture was prepared and studied as a Co²⁺‐, Ni²⁺‐, and Cu²⁺‐sorbing material. This hydrogel was obtained by the synthesis of a PAA in the presence of a second presynthesized PAA carrying many primary amino groups as side substituents, which acted as a macromolecular crosslinking agent. Therefore, it had an intersegmented structure. INT‐PAA1 exhibited a remarkable sorption capacity and sorption rate for Co²⁺, Ni²⁺, and Cu²⁺ that were advantageously in situ monitored by cyclic voltammetry. An extended X‐ray absorption fine structure spectroscopy characterization of the Co²⁺/INT‐PAA1 complex was also performed. The very fast and quantitative metal‐ion uptake, made apparent by an intense coloring of the hydrogel, showed remarkable potential for environmental applications such as heavy‐metal detection, recovery, and elimination. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2316–2327, 2006     

Synthesis and X‐ray single‐crystal structure study of 5,5′‐bis(silyl)‐functionalized 3,3′‐dibromo‐2,2′‐dithiophenes

A high‐yield synthesis toward 5,5′‐bis(silyl)‐functionalized 3,3′‐dibromo‐2,2′‐dithiophenes with very efficient work‐up procedure is presented. The molecular structures of two silyl functionalized dibromo‐dithiophenes in the solid state have been determined to investigate the structural influences of different functional groups on the degree of π‐conjugation within the dithiophene moieties, as well as their packing properties. The planar alignment of the tert‐butyldimethylsilyl‐functionalized dibromo‐dithiophene shows a significantly higher degree of conjugation of the π‐system with a more favorable molecular packing than the skewed arrangement of the triisopropylsilyl‐substituted species. Copyright © 2005 John Wiley & Sons, Ltd.     

Fe K‐Edge X‐ray Absorption Fine Structure Determination of γ‐Al2O3‐Supported Iron‐Oxide Species

The structure of FeO_x species supported on γ‐Al₂O₃ was investigated by using Fe K‐edge X‐ray absorption fine structure (XAFS) and X‐ray diffraction (XRD) measurements. The samples were prepared through the impregnation of iron nitrate on Al₂O₃ and co‐gelation of aluminum and iron sulfates. The dependence of the XRD patterns on Fe loading revealed the formation of α‐Fe₂O₃ particles at an Fe loading of above 10 wt %, whereas the formation of iron‐oxide crystals was not observed at Fe loadings of less than 9.0 wt %. The Fe K‐edge XAFS was characterized by a clear pre‐edge peak, which indicated that the Fe?O coordination structure deviates from central symmetry and that the degree of Fe?O?Fe bond formation is significantly lower than that in bulk samples at low Fe loading (<9.0 wt %). Fe K‐edge extended XAFS oscillations of the samples with low Fe loadings were explained by assuming an isolated iron‐oxide monomer on the γ‐Al₂O₃ surface.     

New Rh(III) complexes of 5‐methyl‐5‐(pyridyl)‐2,4‐imidazolidenedione: Synthesis,X‐ray structure,electrochemical study and catalytic behaviour for hydrogenation of ketones

We describe the reaction of anion [RhCl₆]³⁻ with a series of hydantoin ligands (HL1, HL2 and HL3 = 5‐methyl‐5‐(2‐, 3‐ and 4‐pyridyl)‐2,4‐imidazolidenedione, respectively). Based on spectroscopic, cyclic voltammetric, elemental and MS analyses, the complexes have the general formula K[RhCl₂(L1)₂] ( 1 ), cis ‐ and trans ‐K[RhCl₄(HL2)₂] ( 2a and 2b ) and cis ‐ and trans ‐K[RhCl₄(HL3)₂] ( 3a and 3b ). Complexes 2a , 2b , 3a and 3b were characterized successfully using infrared, ¹H NMR and ¹³C NMR spectral analyses. Dissolution of complex 1 in dimethylsulfoxide (DMSO) led to elimination of one KL1 ligand and coordination of two DMSO molecules as ligands and transformation of this complex to cis ‐ and trans ‐[RhCl₂L1(DMSO)₂] ( 1a and 1b ). Recrystallization led to separation and isolation of crystals of 1a from the initial mixture. X‐ray analysis results showed that this complex was crystallized as solvated complex cis ‐[RhCl₂L1(DMSO)₂]DMSO. The catalytic activity of these complexes was then evaluated for the hydrogenation of various ketones.     

Online wide‐angle X‐ray diffraction/small‐angle X‐ray scattering measurements for the CO2‐laser‐heated drawing of poly(ethylene terephthalate) fiber

Fiber‐structure‐development in the poly(ethylene terephthalate) fiber drawing process was investigated with online measurements of wide‐angle and small‐angle X‐ray scattering with both a high‐luminance X‐ray source and a CO₂‐laser‐heated drawing system. The intensity profile of the transmitted X‐ray confirmed the location of the neck‐drawing point. The diffraction images had a time resolution of several milliseconds, and this still left much room for improvement. Crystal diffraction appeared in the wide‐angle X‐ray images almost instantaneously about 20 ms after necking, whereas a four‐point small‐angle X‐ray scattering pattern appeared immediately after necking. With the elapse of time after necking, the four‐point scattering pattern changed into a meridional two‐point shape. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1090–1099, 2005     

Microsecond X‐ray Absorption Spectroscopy Identification of CoI Intermediates in Cobaloxime‐Catalyzed Hydrogen Evolution

Rational development of efficient photocatalytic systems for hydrogen production requires understanding the catalytic mechanism and detailed information about the structure of intermediates in the catalytic cycle. We demonstrate how time‐resolved X‐ray absorption spectroscopy in the microsecond time range can be used to identify such intermediates and to determine their local geometric structure. This method was used to obtain the solution structure of the Co^I intermediate of cobaloxime, which is a non‐noble metal catalyst for solar hydrogen production from water. Distances between cobalt and the nearest ligands including two solvent molecules and displacement of the cobalt atom out of plane formed by the planar ligands have been determined. Combining in situ X‐ray absorption and UV/Vis data, we demonstrate how slight modification of the catalyst structure can lead to the formation of a catalytically inactive Co^I state under similar conditions. Possible deactivation mechanisms are discussed.     

The effect of amide solvent structure on the direct arylation polymerization (DArP) of 2‐Bromo‐3‐hexylthiophene

In this work, we investigate the influence of the amide solvent chemical structure on the properties of poly(3‐hexylthiophene) (P3HT) prepared via direct arylation polymerization (DArP). Our findings indicate that for successful polymerization the amide must possess an acyclic aliphatic structure since cyclization of an amide results in a complete shutdown of DArP reactivity as evidenced by failed polymerization in N‐methylpyrrolidone, whereas the presence of an aromatic motif renders the amide solvent susceptible to C? H activation and leads to incorporation of the solvent structure into the P3HT backbone, as demonstrated on the example of N,N‐diethylbenzamide. Additionally, we observed that the steric bulk of alkyl substituents on both the nitrogen atom and the carbonyl group within the amide structure has to be delicately balanced for optimal DArP reactivity. In the optimal cases, P3HT is obtained in high yield, with high molecular weight and contains a minimal amount of structural defects. The obtained polymer samples were comprehensively studied in terms of their chemical structure, optical, thermal and solid‐state properties in thin films using GPC analysis, ¹H NMR, MALDI, UV–vis, GIXRD spectroscopy, and DSC. We additionally note a drastic difference of the amide solvent effect between DArP and Stille polymerization. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2494–2500     

Synthesis,spectroscopic and X‐ray single‐crystal structure study of bis(2‐methoxy‐ethanolato)‐bis(8‐quinolinato)titanium(IV)

Reaction of Ti(OCH₂CH₂OR)₄ (R?CH₃ and C₂H₅) with 8‐hydroxyquinoline in benzene at room temperature resulted in the formation of Ti(C₉H₆NO)₂(OCH₂CH₂OR)₂, characterized by IR, ¹H‐NMR, UV and mass spectroscopies. The molecular structure of Ti(C₉H₆NO)₂(OCH₂CH₂OCH₃)₂ has been determined by single‐crystal X‐ray structure analysis. The geometry at titanium is a distorted octahedron, with the nitrogen atoms of quinolinate occupying the trans position with respect to oxygens of the 2‐methoxyethoxy groups. The prepared quinolinate derivatives of titanium alkoxides are very stable towards hydrolysis and harsh conditions are required for hydrolytic cleavage. Copyright © 2005 John Wiley & Sons, Ltd.     

Characterization of multicomponent polymer trilayers with resonant soft X‐ray reflectivity

Resonant soft X‐ray reflectivity (RSoXR) has been used to quantify the layer thicknesses and the interfacial widths of a single, complex thin film with three polymeric layers supported on an inorganic substrate. By adjusting the photon energy, the sensitivity to particular interfaces within the trilayer can be selectively enhanced. The results significantly improve and broaden the capabilities of RSoXR, which has previously only been demonstrated and used for bilayers on silicon substrates. The capability of RSoXR to characterize polymer trilayers was not readily predictable from prior bilayer results, as the RSoXR characterization of bilayers benefits from a strong X‐ray reflection from the substrate that serves as a reference beam with which the reflections from the other interfaces interfere with. The impact of having the capability to investigate trilayers is exemplified by discussing the utility of RSoXR to characterize organic electronic light emitting multilayers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1291–1299, 2009     

New Insights into the Nature of Co‐components and Their Impact on Pd Structure: X‐ray Absorption Studies on Toluene Acetoxylation Catalysts

Co‐components are a powerful tool to tune the performance of catalysts, but their nature and their impact on the catalysts is often controversially discussed. In this study X‐ray absorption spectroscopy (XAS) was employed to elucidate the nature of co‐components and their impact on the catalytic reaction. In anatase‐supported Pd‐based catalysts for the gas‐phase acetoxylation of toluene, less noble co‐components (e.g., Mn, Co, and Sb) spread over the support in their oxidic form and changed their valence state on stream. Incorporated atoms such as C or a small part of the Sb affect the electronic structure of Pd. For the noble Au, only a weak interaction with the support and Pd was observed during time on stream. Only XAS at the K‐edges together with investigations of the Pd L‐edge for a better understanding of the electronic structure, supplemented by STEM for elemental mapping, allow such detailed insights.     

X‐ray studies on the double melting behavior of poly(butylene terephthalate)

The double melting behavior of poly(butylene terephthalate) (PBT) was studied with differential scanning calorimetry (DSC) and wide‐angle X‐ray analysis. DSC melting curves of melt‐crystallized PBT samples, which we prepared by cooling from the melt (250 °C) at various cooling rates, showed two endothermic peaks and an exothermic peak located between these melting peaks. The cooling rate effect on these peaks was investigated. The melt‐crystallized PBT sample cooled at 24 K min^?1 was heated at a rate of 1 K min^?1, and its diffraction patterns were obtained successively at a rate of one pattern per minute with an X‐ray measurement system equipped with a position‐sensitive proportional counter. The diffraction pattern did not change in the melting process, except for the change in its peak height. This suggests that the double melting behavior does not originate from a change in the crystal structure. The temperature dependence of the diffraction intensity was obtained from the diffraction patterns. With increasing temperature, the intensity decreased gradually in the low‐temperature region and then increased distinctly before a steep decrease due to the final melting. In other words, the temperature‐dependence curve of the diffraction intensity showed a peak that is interpreted as proof of the recrystallization in the melting process. The peak temperature was 216 °C. The temperature‐dependence curve of the enthalpy change obtained by the integration of the DSC curve almost coincided with that of the diffraction intensity. The double melting behavior in the heating process of PBT is concluded to originate from the increase of crystallinity, that is, recrystallization. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2005–2015, 2001     

Mesoscale Characterization of Nanoparticles Distribution Using X‐ray Scattering

The properties of many functional materials depend critically on the spatial distribution of an active phase within a support. In the case of solid catalysts, controlling the spatial distribution of metal (oxide) nanoparticles at the mesoscopic scale offers new strategies to tune their performance and enhance their lifetimes. However, such advanced control requires suitable characterization methods, which are currently scarce. Here, we show how the background in small‐angle X‐ray scattering patterns can be analyzed to quantitatively access the mesoscale distribution of nanoparticles within supports displaying hierarchical porosity. This is illustrated for copper catalysts supported on meso‐ and microporous silica displaying distinctly different metal distributions. Results derived from X‐ray scattering are in excellent agreement with electron tomography. Our strategy opens unprecedented prospects for understanding the properties and to guide the synthesis of a wide array of functional nanomaterials.     

In Situ Observation of the Thermally Induced Growth of Platinum‐Nanoparticle Catalysts Using High‐Temperature X‐ray Diffraction

Fundamental understanding about the thermal stability of nanoparticles and deliberate control of structural and morphological changes under reactive conditions is of general importance for a wide range of reaction processes in heterogeneous and electrochemical catalysis. Herein, we present a parametric study of the thermal stability of carbon‐supported Pt nanoparticles at 80 °C and 160 °C, with an initial particle size below 3 nm, using in situ high‐temperature X‐ray diffraction (HT‐XRD). The effects on the thermal stability of carbon‐supported Pt nanoparticles are investigated with control parameters such as Brunauer–Emmet–Teller (BET) surface area, metal loading, temperature, and gas environment. We demonstrate that the growth rate exhibits a complex, nonlinear behavior and is largely controlled by the temperature, the initial particle size, and the interparticle distance. In addition, an ex situ transmission electron microscopy study was performed to verify our results obtained from the in situ HT‐XRD study.     

Synthesis and single crystal X‐ray determination of the Schiff base 1‐[(2‐isopropyl‐5‐methylphenoxy)hydrazono] ethyl ferrocene

The reaction of acetylferrocene [Fe(η‐C₅H₅)(η‐C₅H₄COCH₃)] (1) with (2‐isopropyl‐5‐methylphenoxy) acetic acid hydrazide [CH₃C₆H₃CH(CH₃)₂OCH₂CONHNH₂] (2) in refluxing ethanol gives the stable light‐orange–brown Schiff base 1‐[(2‐isopropyl‐5‐methylphenoxy)hydrazono] ethyl ferrocene, [CH₃C₆H₃CH(CH₃)₂OCH₂CONHN?C(CH₃)Fe(η‐C₅H₅)(η‐C₅H₄)] (3). Complex 3 has been characterized by elemental analysis, IR, ¹H NMR and single crystal X‐ray diffraction study. It crystallizes in the monoclinic space group P2₁/n, with a = 9.6965(15), b = 7.4991(12), c = 29.698(7) Å, β = 99.010(13) °, V = 2132.8(7) ų, D_calc = 1.346 Mg m^?3; absorption coefficient, 0.729 mm^?1. The crystal structure clearly shows the characteristic [N? H···O] hydrogen bonding between the two adjacent molecules of 3. This acts as a bidentale ligand, which, on treatment with [Ru(CO)₂Cl₂] _n, gives a stable bimetallic yellow–orange complex (4). Copyright © 2002 John Wiley & Sons, Ltd.     

High-sensitivity x-ray absorption fine structure investigation of arsenic shallow implant in silicon

High-sensitivity fluorescence-yield x-ray absorption fine structure spectroscopy (XAFS) has been investigated to characterize the local structure around arsenic shallow implant in silicon. Fluorescence-yield XAFS experiments were performed using a high-brilliance synchrotron radiation beam from an in-vacuum-type undulator in a third-generation light source. In addition to investigating the efficiency of high-brilliance undulator x-rays during the fluorescence-yield XAFS measurements, we compared the analytical performance of both the wavelength dispersive spectrometer (WDS) and the energy dispersive spectrometer (EDS) based on the silicon drift detector (SDD). It was confirmed that the WDS reduces the influence of scattering background due to the high spectral resolution. Another advantage of the WDS is high counting rate measurements. It was found that fluorescence-yield XAFS using undulator x-rays combined with the WDS permits superior sensitivity measurements.     

Confirmation of the crystal structure of poly(p‐phenylene benzobisoxazole) by the X‐ray structure analysis of model compounds and the energy calculation

To check the previously proposed crystal structure of poly(p‐phenylene benzobisoxazole) [PBO], we performed an X‐ray structure analysis for single crystals of low molecular weight model compounds with the following chemical formulas: Both of these two model compounds show essentially the same molecular and subcell structures as those of PBO: the molecular chains take an almost perfect planar conformation and are packed together with a relative height between the adjacent chains of about 3 Å along the chain axis, although for the polymer the chains are shifted by the same value but in a disordered mode with respect to the direction of the shift (upward or downward), different from the regular packing in model compounds. These structural features are reproduced well with energy calculations. Structural ordering in PBO fibers caused by heat treatment at high temperatures, as clarified by X‐ray diffraction measurement, are interpreted on the basis of the energy calculations. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1296–1311, 2001     

Poly(3‐hexylthiophene) aggregation at solvent–solvent interfaces

The aggregation behavior of P3HT is investigated at the interface of orthogonal solvents for P3HT. The changeable characteristics of P3HT aggregate dispersions, for example, extent of aggregation and intrachain order, are studied by varying (1) the interfacial area, (2) the poor solvent used to induce aggregation – dichloromethane (DCM), hexane (HEX), and acetonitrile (AcN) – and (3) the relative composition of the good solvent, chloroform (CF), and poor solvents. The results are compared to those observed using rapid injection of the solvent. Miscibility gap values (Δδ) provide a reasonable justification of the assembly behavior of P3HT in the solvent mixtures in terms of the kinetics of polymer aggregation and the kinetics of solvent mixing at the interface. Atomic force microscopy (AFM) is used to analyze the morphology of films processed from dispersions with disparate characteristics, but having the same solvent composition, for example, 70:30 CF:HEX or 60:40 CF:DCM. Based on the disparity of the kinetics and miscibility gap values, the prevalence of specific structural motifs in the films, for example, spheroids (globules) and fibers, is effectively rationalized in terms of the structural attributes of the aggregates in the liquid phase rather than the evaporation rate (boiling point) differences of the solvents in the mixture. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 999–1011     

Semidilute solution structure of cellulose in an ionic liquid and its mixture with a polar organic co‐solvent studied by small‐angle X‐ray scattering

Structural and thermodynamic properties of cellulose solutions in the ionic liquid 1‐ethyl‐3‐methylimidazolium acetate (EMIMAc) and its binary mixtures with N,N‐dimethyl formamide (DMF) are studied by small‐angle X‐ray scattering (SAXS). These measurements indicate molecular dissolution of the cellulose chains without any significant aggregation. The power–law relationships of the evaluated correlation length and osmotic modulus to concentration exhibit exponents of ?0.76 and 2.06 for EMIMAc and ?0.80 and 2.14 for DMF/EMIMAc solvent mixture, respectively. Thus, these solvents can be considered to be good solvents for cellulose. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 888–894