Rheology,electrical conductivity,and the phase behavior of cocontinuous PA6/ABS blends with MWNT: Correlating the aspect ratio of MWNT with the percolation threshold

Multiwalled carbon nanotubes (purified, p‐MWNT and ～ NH₂ functionalized, f‐MWNT) were melt‐mixed with 50/50 cocontinuous blends of polyamide 6 (PA6) and acrylonitrile–butadiene–styrene in a conical twin‐screw microcompounder to obtain conductive polymer blends utilizing the conceptual approach of double‐percolation. The state of dispersion of the tubes was assessed using AC electrical conductivity measurements and melt‐rheology. The rheological and the electrical percolation threshold was observed to be ～ 1–2 wt % and ～ 3–4 wt %, respectively, for blends with p‐MWNT. In case of blends with f‐MWNT, the rheological percolation threshold was observed to be higher (2–3 wt %) than p‐MWNT but the electrical percolation threshold remained almost same. However, the absolute values were significantly lower than blends with p‐MWNT. In addition, significant refinement in the cocontinuous morphology of the blends with increasing concentration of MWNT was observed in both the cases. Further, an attempt was made to understand the underlying concepts in relation to cocontinuous morphologies that how the geometrical percolation threshold which adversely suffered because of the attrition of tubes under prolonged shear contributed further in retaining the rheological percolation threshold. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1619–1631, 2008     

形状记忆聚偏氟乙烯/丙烯酸酯/碳纳米管纳米复合材料的导电及导热性能

利用聚偏氟乙烯（PVDF）微小结晶的物理交联点作用,制备了形状记忆性能优异的聚偏氟乙烯/丙烯酸酯聚合物（PVDF/ACM）共混材料,为提高其导电及导热性能,于其中引入了碳纳米管（CNT）,系统研究了PVDF/ACM/CNT三元体系纳米复合材料的导热及导电性能。 结果表明,碳纳米管在PVDF/ACM体系中分散均匀;在基本保持其形状记忆性能的前提下,碳纳米管的加入使材料导热性能及导电性能有较大程度的提高：质量分数为4%的CNT使材料25 ℃的电阻值降低至5000 Ω/square,导热系数提高至0.157 W/(m·K)。     

A Review Featuring Fabrication,Properties and Applications of Carbon Nanotubes (CNTs) Reinforced Polymer and Epoxy Nanocomposites

Carbon nanotubes (CNTs) have long been recognized as the stiffest and strongest man-made material known to date.In addition,their high electrical conductivity has roused interest in the areas of electrical appliances and communication related applications.However,due to their miniature size,the excellent properties of these nanostructures can only be exploited if they are homogeneously embedded into light-weight matrices as those offered by a whole series of engineering polymers.In order to enhance their chemical affinity to engineering polymer matrices,chemical modification of the graphitic sidewalls and tips is necessary.The mechanical and electrical properties to date of a whole range of nanocomposites of various carbon nanotube contents are also reviewed in this attempt to facilitate progress in this emerging area.Recently,carbonaceous nano-fillers such as graphene and carbon nanotubes (CNTs) play a promising role due to their better structural and functional properties and broad range of applications in every field.Since CNTs usually form stabilized bundles due to van der Waals interactions,they are extremely difficult to disperse and align in a polymer matrix.The biggest issues in the preparation of CNTs reinforced composites reside in efficient dispersion of CNTs into a polymer matrix,the assessment of the dispersion,and the alignment and control of the CNTs in the matrix.An overview of various CNT functionalization methods is given.In particular,CNT functionalization using click chemistry and the preparation of CNT composites employing hyperbranched polymers are stressed as potential techniques to achieve good CNT dispersion.In addition,discussions on mechanical,thermal,electrical,electrochemical and applications ofpolymer/CNT composites are also included.     

Phase morphology development in PP/PA6 blends induced by a maleated thermoplastic elastomer

The effects of maleated thermoplastic elastomer (TPEg) on morphological development of polypropylene (PP)/polyamide 6 (PA6) blends with a fixed PA6 content (30 wt %) were investigated. For purpose of comparison, nonmaleated thermoplastic elastomer (TPE) was also added to the above binary blends. A comparative study of FTIR spectroscopy in above both ternary blends confirmed the formation of in situ graft copolymer in the PP/PA6/TPEg blend. Dynamic mechanical analysis (DMA) indicated that un‐like TPE, the incorporation of TPEg remarkably affected both intensity and position of loss peaks of blend components. Scanning electron microscopy (SEM) demonstrated that PP/PA6/TPE blends still exhibited poor interfacial adhesion between the dispersed phase and matrix. However, the use of TPEg induced a finer dispersion and promoted interfacial adhesion. Transmission electron microscopy (TEM) for PP/PA6/TPEg blends showed that a core‐shell structure consisting of PA6 particles encapsulated by an interlayer was formed in PP matrix. With the concentration of TPEg increasing, the dispersed core‐shell particles morphology was found to transform from discrete acorn‐type particles to agglomerate with increasing degree of encapsulation. The modified Harkin's equation was applied to illustrate the evolution of morphology with TPEg concentration. “Droplet‐sandwiched experiments” further confirmed the encapsulation morphology in PP/PA6/TPEg blends. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1050–1061, 2006     

Influence of multiwall carbon nanotubes on morphology and electrical conductivity of PP/ABS blends

Polypropylene (PP) and acrylonitrile‐butadiene‐styrene (ABS) blends with multiwall carbon nanotubes (MWNT) were prepared by melt mixing. PP/ABS blends without MWNT revealed coarse co continuous structures on varying the ABS content from 40 to 70 wt %. Bulk electrical conductivity of the blends showed lower percolation threshold (0.4–0.5 wt %) in the 45/55 co continuous blends whereas the percolation threshold was between 2 and 3 wt % in matrix‐particle dispersed morphology of 80/20 blends. Interestingly, droplet size was observed to decrease with addition of MWNT above percolation threshold in 80/20 blends. Further, the bulk electrical conductivity was found to be dependent on the melt flow index of PP. The non‐polar or weakly polar nature of blends constituents resulted in the temperature independent dielectric constant, dielectric loss, and DC electrical conductivity. Rheological analysis revealed the formation of 3D network‐like structure in 80/20 PP/ABS blends at 3 wt % MWNT. An attempt was made to understand the relationship between rheology, morphology, and electrical conductivity of these blends. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2286–2295, 2008     

Effects of processing conditions on rheological,thermal, and electrical properties of multiwall carbon nanotube/epoxy resin composites

We report on the effect of processing conditions on rheology, thermal and electrical properties of nanocomposites containing 0.02–0.3 wt % multiwall carbon nanotubes in an epoxy resin. The influence of the sonication, the surface functionalization during mixing, as well as the application of external magnetic field (EMF) throughout the curing process was examined. Rheological tests combined with optical microscopy visualization are proved as a very useful methodology to determine the optimal processing conditions for the preparation of the nanocomposites. The Raman spectra provide evidence for more pronounced effect on the functionalized with hardener compositions, particularly by curing upon application of EMF. Different chain morphology of CNTs is created depending of the preparation conditions, which induced different effects on the thermal and electrical properties of the nanocomposites. The thermal degradation peak is significantly shifted towards higher temperatures by increasing the nanotube content, this confirming that even the small amount of carbon nanotubes produces a strong barrier effect for the volatile products during the degradation. The ac conductivity measurements revealed lower values of the percolation threshold (pc) in the range of 0.03–0.05 wt %. CNTs for the nanocomposites produced by preliminary dispersing of nanotubes in the epoxy resin, compared to those prepared by preliminary functionalization of the nanotubes in the amine hardener. This is attributed to the higher viscosity and stronger interfacial interactions of the amine hardener/CNT dispersion which restricts the reorganization of the nanotubes. The application of the EMF does not influence the pc value but the dc conductivity values (σ_dc) of the nanocomposites increased at about one order of magnitude due to the development of the aforementioned chain structure. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Influence of organo-clay on electrical and mechanical properties of PP/MWCNT/OC nanocomposites

The electrical, thermal and mechanical properties of nanocomposites, based on polypropylene (PP) filled by multi-walled carbon nanotubes (MWCNTs) and organo-clay (OC), were studied with the purpose of finding out the effect of OC on the microstructure of MWCNTs dispersion and PP/MWCNT/OC composites. It was found that addition of organo-clay nanoparticles improved nanotube dispersion and enhanced electrical properties of PP/MWCNT nanocomposites. Addition of organo-clay (MWCNT/OC ratio was 1/1) reduced the percolation threshold of PP/MWCNT nanocomposites from ?_c = 0.95 vol.% to ?_c = 0.68 vol.% of carbon nanotubes, while the level of conductivity became 2–4 orders of magnitude higher. The DSC and DMA analyses have shown that the influence of organo-clay on the thermal and mechanical properties of material was not significant in composites with both fillers as compared to PP/OC. Such an effect can be caused by stronger interaction of OC with carbon nanotubes than with polymer matrix.     

Electrical and melt rheological characterization of PC and co‐continuous PC/SAN blends filled with CNTs: Relationship between melt‐mixing parameters,filler dispersion,and filler aspect ratio

Electrical and melt rheological properties of melt‐mixed polycarbonate (PC) and co‐continuous PC/poly(styrene–acrylonitrile) (SAN) blends with carbon nanotubes (CNTs) are investigated. Using two sets of mixing parameters, different states of filler dispersion are obtained. With increasing CNT dispersion, an increase in electrical resistivity near the percolation threshold of PC–CNT composites and (PC + CNT)/SAN blends is observed. This suggests that the higher mixing energies required for better dispersion also result in a more severe reduction of the CNT aspect ratio; this effect was proven by CNT length measurements. Melt rheological studies show higher reinforcing effects for composites with worse dispersion. The Eilers equation, describing the melt viscosity as function of filler content, was used to fit the data and to obtain information about an apparent aspect ratio change, which was in accordance with measured CNT length reduction. Such fitting could be also transferred to the blends and serves for a qualitatively based discussion. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 79–88     

Thermal properties of single walled carbon nanotubes composites of polyamide 6/poly(methyl methacrylate) blend system

The nanocomposites of polyamide 6 (PA6)/poly(methyl methacrylate) (PMMA)/non-functionalized and functionalized [carboxylic acid (COOH) and hydroxyl (OH)] single wall carbon nanotubes (SWCNTs) were prepared in mass ratios of 79.5/19.5/1, 49.5/49.5/1, and 19.5/79.5/1 by melt–mixing method at 230 °C. The PA6/PMMA blends with mass ratios of 80/20, 50/50, and 20/80 served as references. The Fourier transform infrared analyses of nanocomposites showed the formation of hydrogen bond interactions among PA6, PMMA, and OH and COOH functional groups of SWCNTs. The nanocomposites and blends had higher thermal stability with respect to the PMMA. The differential scanning calorimeter (DSC) curves showed that the nanocomposites and blends exhibited two T _g values at around 51 and 126 °C for PA6 and PMMA, respectively. About 20 °C early crystallization was observed in nanocomposites compared to the blends. The dynamic mechanical analysis (DMA) results suggested that among all the compositions of blends and nanocomposites, storage modulus (E′) was higher for PMMA-rich blends and nanocomposites. At 25 °C, the E′ values were higher for blends and nanocomposites compared to the neat PA6. The tan δ curves indicated that the more heterogeneity of the hybrid nature resulted in PA6/PMMA/SWCNTs-OH or SWCNTs-COOH with 79.5/19.5/1 mass ratio nanocomposites compared to the PA6/PMMA with 80/20 mass ratio blend. The higher T _g values of PA6 and PMMA were observed in DMA studies compared to the DSC studies for PA6 and PMMA as neat and in blends and nanocomposites. The significant improvements in crystallization of nanocomposites were considered resulting from achieving better compatibility among the polymer components and carbon nanotubes.     

An experimental investigation on the conductive behavior of carbon nanotube-reinforced natural polymer nanocomposites

It is well known that carbon nanotubes (CNTs) have excellent electrical properties and can be used as the nanofiller in natural polymers to produce conductive CNT/polymer nanocomposites. In this study, the conductive behavior of CNT-reinforced natural polymer nanocomposites was investigated. The effect of CNT concentration on the conductivity of CNT/natural polymer nanocomposites was also investigated. The natural polymers used were plasticized starch (PS) and chitosan (CS). FTIR spectroscopy was used to examine the interactions between PS, CS, and CNTs. TEM analysis on both nanocomposites were made to study the dispersion states of CNTs in both polymers. The results showed that the surface resistivities of both CNT/PS and CNT/CS nanocomposites decreased steeply with increasing CNT concentration. Particularly, the CNT/CS nanocomposites showed a better conductivity than the CNT/PS composites at the same CNT concentration. The TEM result showed that CNT/CS nanocomposites had better dispersibility and formation of fully connected, three-dimensional network structures between the CNTs than the CNT/PS nanocomposites, which results in the superior conductive property of CNT/CS nanocomposites compared to the CNT/PS nanocomposites.     

Thermal,mechanical and electroactive shape memory properties of polyurethane (PU)/poly (lactic acid) (PLA)/CNT nanocomposites

Polymer blend nanocomposites based on thermoplastic polyurethane (PU) elastomer, polylactide (PLA) and surface modified carbon nanotubes were prepared via simple melt mixing process and investigated for its mechanical, dynamic mechanical and electroactive shape memory properties. Chemical and structural characterization of the polymer blend nanocomposites were investigated by Fourier Transform infrared (FT-IR) and wide angle X-ray diffraction (WAXD). Loading of the surface modified carbon nanotube in the PU/PLA polymer blends resulted in the significant improvement on the mechanical properties such as tensile strength, when compared to the pure and pristine CNT loaded polymer blends. Dynamic mechanical analysis showed that the glass transition temperature (T_g) of the PU/PLA blend slightly increases on loading of pristine CNT and this effect is more pronounced on loading surface modified CNTs. Thermal and electrical properties of the polymer blend composites increases significantly on loading pristine or surface modified CNTs. Finally, shape memory studies of the PU/PLA/modified CNT composites exhibit a remarkable recoverability of its shape at lower applied dc voltages, when compared to pure or pristine CNT loaded system.     

Critical aspects related to processing of carbon nanotube/unsaturated thermoset polyester nanocomposites

Carbon nanotubes (CNTs) have outstanding mechanical, thermal and electrical properties. As a result, particular interest has been recently given in exploiting these properties by incorporating carbon nanotubes into some form of matrix. Although unsaturated polyesters with styrene have widespread use in the industrial applications, surprisingly there is no study in the literature about CNT/thermoset polyester nanocomposite systems. In the present paper, we underline some important issues and limitations during the processing of unsaturated polyester resins with different types of carbon nanotubes. In that manner, 3-roll mill and sonication techniques were comparatively evaluated to process nanocomposites made of CNTs with and without amine (NH₂) functional groups and polyesters. It was found that styrene evaporation from the polyester resin system was a critical issue for nanocomposite processing. Rheological behaviour of the suspensions containing CNTs and tensile strengths of their resulting nanocomposites were characterized. CNT/polyester suspensions exhibited a shear thinning behaviour, while polyester resin blends act as a Newtonian fluid. It was also found that nanotubes with amine functional groups have better tensile strength, as compared to those with untreated CNTs. Transmission electron microscopy (TEM) was also employed to reveal the degree of dispersion of CNTs in the matrix.     

Influence of SEBS-g-MA on morphology, mechanical, and thermal properties of PA6/PP/organoclay nanocomposites

Polyamide 6/polypropylene (PA6/PP = 70/30 parts) blends containing 4 phr (parts per hundred resin) of organically modified clay (organoclay) toughened with maleated styrene-ethylene-butylene-styrene (SEBS-g-MA) were prepared by melt compounding using co-rotating twin-screw extruder followed by injection molding. X-ray diffraction (XRD) and transmission electron microscope (TEM) were used to characterize the structure of the nanocomposites. The mechanical properties of the nanocomposites were determined by tensile, flexural, and notched Izod impact tests. The single edge notch three point bending test was used to evaluate the fracture toughness of SEBS-g-MA toughened PA6/PP nanocomposites. Thermal properties were studied by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). XRD and TEM results indicated the formation of the exfoliated structure for the PA6/PP/organoclay nanocomposites with and without SEBS-g-MA. With the exception of stiffness and strength, the addition of SEBS-g-MA into the PA6/PP/organoclay nanocomposites increased ductility, impact strength and fracture toughness. The elongation at break and fracture toughness of PA6/PP blends and nanocomposites were increased with increasing the testing speed, whereas tensile strength was decreased. The increase in ductility and fracture toughness at high testing speed could be attributed to the thermal blunting mechanism in front of crack tip. DSC results revealed that the presence of SEBS-g-MA had negligible effect on the melting and crystallization behavior of the PA6/PP/organoclay nanocomposites. TGA results showed that the incorporation of SEBS-g-MA increased the thermal stability of the nanocomposite.     

Thermal degradation and kinetic analysis of biodegradable PBS/multiwalled carbon nanotube nanocomposites

In this study, carbon nanotubes (CNTs) were first modified using N,N′‐ dicyclohexylcarbodiimide (DCC) dehydrating agents. Subsequently, the poly(butylene succinate)/multiwalled carbon nanotube (PBS/MWNTs) nanocomposites were prepared through facile melt blending. Thermal degradation of these PBS/MWNT nanocomposites was investigated; the kinetic parameters of degradation were calculated using the Coats and Redfern, Ozawa, and Horowitz and Metzger methods, respectively. It was found that the degradation reaction mechanism of PBS and the CNT‐C18 containing nanocomposites at lower temperature was likely to produce an F1 model through reaction of random chain cleavage (cis‐elimination). However, the reaction mechanism at higher temperature was likely to be a D1 model because of the dominant diffusion control effect. Moreover, it was found that the activation energies of CNT‐C18‐containing PBS nanocomposites were first increased with the content of CNT‐C18, but then decreased after the content was larger than 0.5 wt % for all models at differing heating rates. This may be due to the formation of a conductive network of CNTs in the polymer matrix at higher content of CNTs, which lead to better heat and electrical conductivity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1231–1239, 2009     

马来酸酐接枝热塑性弹性体在PP/PA6共混物中的作用

研究了马来酸酐接枝热塑性弹性体 (TPEg )作为增容剂对聚丙烯 (PP) 尼龙 6 (PA6 )共混体系的相容性、相态以及物理力学性能的影响 .研究结果表明TPEg的加入大大改善了PP PA6共混体系的相容性 ,且随TPEg含量的增大分散相粒径明显降低 ,共混物的韧性以及延展性大大提高 ,同时拉伸强度及模量仍保持较好的水平 .TPEg增容的PP PA6共混物的非等温结晶行为的研究表明 ,共混物中PP和PA6的结晶行为不同于各自纯的聚合物 ,PA6作为成核剂使PP的结晶温度提高 ;而PA6由于TPEg的加入 ,出现分级结晶现象 ,一级结晶温度略低于纯PA6的结晶温度 ,且随TPEg含量增大结晶受阻 ,二级结晶温度与PP的接近 .由于PP、PA 6以及TPEg之间存在较强的相互作用 ,三元共混物中PP及PA6的玻璃化转变温度分别较其纯聚合物升高 .基于上述结果 ,提出了本共混体系的结构模型     

The effect of a semi‐industrial masterbatch process on the carbon nanotube agglomerates and its influence in the properties of thermoplastic carbon nanotube composites

This study details an industrial process to prepare polypropylene (PP) composites reinforced with different loadings (0.5–10wt.%) of carbon nanotubes (CNTs) from a direct dilution of a masterbatch produced by an optimized extrusion compounding process. The work demonstrates how the anisotropy in the distribution of CNTs can have a positive effect on the electrical conductivity and fracture toughness of the resulting composites. The composite with the highest loading of CNTs had an electrical conductivity of 10^?2 S/m comparable with those reported in the available literature. The composites showed anisotropy in their properties that seems to be caused by the non‐homogeneous distribution of the agglomerates produced by the orientation of the flow direction during the injection process. The composites produced in this work exhibited a fracture toughness up to 55% higher than neat PP and failed by polymer ductile tearing. It was found that the CNT agglomerates distributed throughout the matrix increased the toughness of PP by promoting plastic deformation of the matrix during the fracture process and by a slight load transfer between the polymer matrix and the CNTs of the agglomerates. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 189–197     

Morphology,rheological and crystallization behavior in non-covalently functionalized carbon nanotube reinforced poly(butylene succinate) nanocomposites with low percolation threshold

Multi-walled carbon nanotubes (CNTs) were non-covalently functionalized by surface wrapping of poly(sodium 4-styrenesulfonate) (PSS) with the aid of ultrasound. The functionalized CNTs were incorporated into poly(butylene succinate) (PBS) through solution coagulation to fabricate CNTs filled PBS nanocomposites. The morphologies of the PBS/CNT nanocomposites were studied by scanning electron microscope (SEM) and transmission electron microscope (TEM), and the effect of loading of functionalized CNT on the rheological behavior, electrical conductivity and mechanical properties of the nanocomposites was investigated systemically. SEM observation indicates that functionalized CNTs dispersed in PBS matrix without obvious aggregation and showed good interfacial adhesion with the PBS phase. TEM observation reveals that a CNT network was formed when the loading of CNTs increased from 0.1 to 0.3 wt%. Rheological investigation indicates the formation of a CNT network with a percolation threshold of only 0.3 wt%. Significant improvement in electrical conductivity occurred at CNT loading of 0.3 wt%, with the value of electrical conductivity increasing by six orders of magnitude compared to neat PBS. Differential scanning calorimetry indicates that the melt crystallization temperature of PBS was improved by ∼14 °C with addition of only 0.05 wt% functionalized CNTs. Tensile tests indicate that both the yield strength and Young's modulus of PBS were apparently reinforced by incorporation of functionalized CNTs, while the elongation at break was reduced gradually.     

滑石粉及混炼顺序对PA6/PP/MAPP合金相形态及力学性能的影响

通过挤出和注射成型制备了滑石粉(Talc)填充的尼龙6/聚丙烯/马来酸酐接枝聚丙烯(PA6/PP/MAPP)合金, 研究了Talc和混炼顺序(一步法和PA6母料法)对合金相形态和力学性能的影响. 场发射扫描电镜(FESEM)分析结果表明, 添加Talc后注射样条中心部分的PP相由球状转变为沿流动方向取向的有分支的条状结构, 且用PA6母料法制样比用一步法制样的相形态更为精细. 溶解PA6相后对PP相进行热重分析(TGA), 确定了Talc在PA6相和PP相中的分布比例, Talc选择性分布于PA6相中. PA6母料法中Talc的分散好于一步法. 研究了材料的拉伸、 弯曲、 冲击、 热变形温度和动态力学性能, Talc的添加能够明显提高材料的刚性, 且母料法样品的性能优于一步法样品.     

磨盘碾磨制备PA6/PP/SBS共混物的结构与性能

采用磨盘形力化学反应器,在室温下制备了PA6/PP超细混合粉体,与SBS共混制得PA6/PP/SBS共混物,测定了材料的力学性能并用TEM研究了材料在不同加工温度下相结构的变化.结果表明,通过固相力化学粉碎制备的PA6/PP混合微粉,改善了PA6与PP和SBS的相容性,促进了PA6及PP的分散和与SBS的相界面结合.在微粉填充量为4%～8%(质量分数)时,材料的拉伸强度大幅度提高,扯断伸长率保持不变.加工温度变化引起材料相结构的变化对材料性能产生显著影响.在PP熔融温度下加工,PP粒子产生粘连形成链状结构,可提高材料的力学性能.     

Isotactic polypropylene/carbon nanotube composites prepared by latex technology: Electrical conductivity study

Several series of nanocomposites were prepared using a latex-based process, the main step of which consisted of mixing an aqueous suspension of exfoliated carbon nanotubes (CNTs) and a polymer latex. In the present work, a systematic study on the electrical properties of fully amorphous (polystyrene - PS) as well as semi-crystalline (isotactic polypropylene - iPP) nanocomposites containing either single-wall (SWCNTs) or multi-wall carbon nanotubes (MWCNTs) has been conducted. Percolation thresholds as low as 0.05 wt.% or 0.1 wt.% were observed for SWCNT/iPP and MWCNT/iPP nanocomposites, respectively. The formation of a conductive percolating network at such a low CNT concentration is favored by the high intrinsic conductivity and the low viscosity of the polymer matrix. The electrical percolation threshold of the iPP-based system was found to be lower than its rheological percolation threshold. Beyond the percolation threshold, MWCNT-based nanocomposites generally exhibited higher conductivity levels than those based on SWCNTs, most probably due to the higher intrinsic conductivity of the MWCNTs as compared to that of the SWCNTs. These excellent electrical properties, associated with the strong nucleating effect of the CNTs reported earlier [1] and [2], render this type of nanocomposites extremely attractive from a technological point of view.