Synthesis and photovoltaic properties of two‐dimensional D‐A copolymers with conjugated side chains

Four novel two‐dimensional (2D) donor–acceptor (D‐A) type copolymers with different conjugated side chains, P1 , P2 , P3 , and P4 (see Fig. 1 ), are designed and synthesized for the application as donor materials in polymer solar cells (PSCs). To the best of our knowledge, there were few reports to systematically study such 2D polymers with D‐A type main chains in this area. The optical energy band gaps are about 2.0 eV for P1 – P3 and 1.67 eV for P4 . PSC devices using P1 – P4 as donor and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester as acceptor in a weight ratio of 1:3 were fabricated and characterized to investigate the photovoltaic properties of the polymers. Under AM 1.5 G, 100 mA/cm² illumination, a high open‐circuit voltage (V_oc) of 0.9 V was recorded for P3 ‐based device due to its low HOMO level, and moderate fill factor was obtained with the best value of 58.6% for P4 ‐based device, which may mainly be the result of the high hole mobility of the polymers (up to 1.82 × 10^?3 cm²/V s). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Novel two‐dimensional donor–acceptor conjugated polymers containing quinoxaline units: Synthesis,characterization, and photovoltaic properties

Novel two‐dimensional donor–acceptor (D–A) structured conjugated polymers, P1–P4, were designed and synthesized by introducing electron‐deficient quinoxaline as core and electron‐rich alkoxyl‐phenylenevinylene in side chains and p‐phenylenevinylene, triphenylamine, or thiophene in main chain. Benefited from the D–A structures, the polymers possess low bandgaps of 1.75 eV, 1.86 eV, 1.59 eV, and 1.58 eV for P1, P2, P3, and P4, respectively, and show broad absorption band in the visible region: the shorter wavelength absorption peak at ～400 nm ascribed to the conjugated side chains and the longer wavelength absorption peak between 500 nm and 750 nm belonging to the absorption of the conjugated main chains. Especially, the absorption band of P4 film covers the whole visible range from 300 nm to 784 nm. The power conversion efficiencies of the polymer solar cells based on P1–P4 as donor and PCBM as acceptor are 0.029%, 0.14%, 0.46%, and 0.57%, respectively, under the illumination of AM 1.5, 100 mW/cm². The polymers with the low bandgap and broad absorption band are promising photovoltaic materials. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4038–4049, 2008     

Effect of side‐chain end groups on the optical,electrochemical, and photovoltaic properties of side‐chain conjugated polythiophenes

Three new side‐chain conjugated polythiophene derivatives, poly{3‐[2‐(3‐methoxy‐4‐octyloxy‐phenyl)‐vinyl]‐thiophene} (P3MOPVT), poly{3‐[2‐(3,5‐dimethoxy‐4‐octyloxy‐phenyl)‐vinyl]‐thiophene} (P3DMOPVT), and poly{3‐[2‐(3,4‐dioctyloxy‐phenyl)‐vinyl]‐thiophene} (P3DOPVT), were synthesized by Wittig‐Hornor reaction and GRIM method and compared with poly{3‐[2‐(4‐octyloxy‐phenyl)‐vinyl]‐thiophene} (P3OPVT) for investigating the effect of the end groups of the conjugated side‐chain on the properties of the polymers. Owing to the electron‐donating ability of methoxy groups, the visible absorption peaks of P3MOPVT and P3DMOPVT solutions and films become stronger and red‐shifted compared with P3OPVT. The electrochemical bandgaps of the four polymers are 2.15 eV for P3OPVT, 1.99 eV for P3MOPVT, 1.85 eV for P3DMOPVT, and 2.36 eV for P3DOPVT, respectively, which indicate that the electron‐donating ability of the methoxy end group on the conjugated side chain of P3MOPVT and P3DMOPVT and the large steric hindrance of the two octyloxy end groups on the conjugated side chain of P3DOPVT have obvious influence on the electrochemical properties of the side‐chain conjugated polythiophenes. Polymer solar cells were fabricated with a structure of ITO/PEDOT:PSS/Polymer:PCBM/LiF/Al. The best device, based on P3DMOPVT, shows a power conversion efficiency of 1.63% under the illumination of AM1.5, 80 mW/cm². © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4916–4922, 2006     

Side chain engineering and conjugation enhancement of benzodithiophene and phenanthrenequnioxaline based conjugated polymers for photovoltaic devices

A series of donor‐acceptor conjugated polymers incorporating benzodithiophene (BDT) as donor unit and phenanthrenequnioxaline as acceptor unit with different side chains have been designed and synthesized. For polymer P1 featuring the BDT unit and alkoxy chains substituted phenanthrenequnioxaline unit in the backbone, serious steric hindrance resulted in quite low molecular weight. The implementation of thiophene ring spacer in polymer P2 greatly suppressed the interannular twisting to extend the effective conjugation length and consequently gave rise to improved absorption property and device performance. In addition, utilizing the alkylthienyl side chains to replace the alkyl side chains at BDT unit in polymer P3 further enhanced the photovoltaic performance due to the increased conjugation length. For polymer P4, translating the alkoxy side chains at the phenanthrenequnioxaline ring into the alkyl side chains at thiophene linker group enhanced molecular planarity and strengthened π?π stacking. Consequently improved absorption property and increased hole mobility were achieved for polymer P4. Our results indicated that side chain engineering not only can influence the solubility of polymer but also can determine the polymer backbone planarity and hence the photovoltaic properties. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1915–1926     

Copolymers of fluorene and thiophene with conjugated side chain for polymer solar cells: Effect of pendant acceptors

Two copolymers of fluorene and thiophene with conjugated side‐chain pending acceptor end group of cyanoacetate ( P2 ) and malononitrile ( P3 ) were synthesized. Both polymers exhibit good thermal stability and low highest occupied molecular orbital level (?5.5 eV). In comparison with P2 , P3 exhibits stronger UV–vis absorption and higher hole mobility. Polymer solar cells based on P3 :PC₇₁BM exhibits a power conversion efficiency of 1.33% under AM 1.5, 100 mW/cm², which is three times of that based on P2 :PC₇₁BM. The higher efficiency is attributed to better absorption, higher hole mobility, and the reduced phase separation scale in P3 :PC₇₁BM blend. The aggregate domain size in P3 :PC₇₁BM blend is 50 nm, much smaller than that in P2 :PC₇₁BM blend (200 nm). Tiny difference in the end groups on side chains of P2 and P3 leads to great difference in phase separation scale, charge transport, and efficiency of their photovoltaic devices. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Effects of substituted side‐chain position on donor–acceptor conjugated copolymers

The optical properties and electrical properties of a series of low‐band‐gap conjugated copolymers, in which alkyl side chains were substituted at various positions, were investigated using donor–acceptor conjugated copolymers consisting of a cyclopentadithiophene derivative and dithienyl‐benzothiadiazole. With substituted side chains, the intrinsic properties of the copolymers were significantly altered by perturbations of the intramolecular charge transfer. The absorption of poly[2, 6‐(4,4‐bis(2‐octyl)‐4H‐cyclopenta‐[2,1‐b:3,4‐b′]dithiophene)‐alt‐4, 7‐bis(4‐octyl‐thiophene‐2‐yl)benzo‐2,1,3‐thiadiazole] [ PCPDT‐ttOTBTOT ( P2 )], which assumed a tail–tail configuration, tended to blue shift relative to the absorption of poly[2,6‐(4,4‐bis(2‐octyl)‐4H‐cyclopenta‐[2,1‐b:3,4‐b′]dithiophene)‐alt‐4,7‐bis (thiophene‐2‐yl)benzo‐2,1,3‐thiadiazole] [ PCPDT‐TBTT ( P1 )]. The absorption of poly[2,6‐(4,4‐bis(2‐octyl)‐4H‐cyclopenta‐[2,1‐b:3, 4‐b′]dithiophene)‐alt‐4,7‐bis(3‐octyl‐thiophene‐2‐yl)benzo‐2,1,3‐thiadiazole] [ PCPDT‐hhOTBTOT ( P3 )], which assumed a head–head configuration, was blue shifted relative to that of P2 . The electrical transport properties of field‐effect transistors were sensitive to the side chain position. The field‐effect mobility in P2 (μ₂ = 1.8 × 10^?3 cm²/V s) was slightly lower than that in P1 (μ₁ = 4.9 × 10^?3 cm²/V s). However, the mobility of P3 was very low (μ₃ = 3.8 × 10^?6 cm²/V s). Photoexcitation spectroscopy showed that the charge generation efficiency (shown in transient absorption spectra) and polaron pair mobility in P1 and P2 were higher than in P3 , yielding P1 and P2 device performances that were better than the performance of devices based on P3 . © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Effects of alkyl side chains positioning and presence of fused aromatic units in the backbone of low‐bandgap diketopyrrolopyrrole copolymers on the optoelectronic properties of organic solar cells

The systematic optimization of the chemical structure of low‐bandgap (LBG) donor‐acceptor polymeric semiconductors is a challenging task for which accurate guidelines are yet to be determined. Several different structural and molecular parameters are crucial ingredients for obtaining LBG polymers that simultaneously possess high power conversion efficiencies, good processability in common organic solvents, and enhanced stability in organic photovoltaic devices. In this work, we present an extensive structure–optoelectronic properties–solar cell performance study on the emerging class of diketopyrrolopyrrole‐based LBG polymers. In particular, we investigate alkyl side chain positioning by introducing linear alkyl side chains into two different positions (α‐ and β‐), and the distance of the electron rich and electron deficient monomers within the repeat units of the polymer chain. We demonstrate that anchoring linear alkyl side chains to the α‐positions and introducing fused moieties into the polymer backbone, can be beneficial toward maintaining photocurrents similar to the unsubstituted derivative, and concurrently exhibit better processabiliy in common organic solvents. These results can provide a design rationale towards further optimization of semiconducting polymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 138–146     

Synthesis and photovoltaic properties of copolymers based on benzo[1,2‐b:4,5‐b′]dithiophene and thiophene with electron‐withdrawing side chains

Six alternating conjugated copolymers ( PL1 – PL6 ) of benzo[1,2‐b:4,5‐b′]dithiophene (BDT) and thiophene, containing electron‐withdrawing oxadiazole (OXD), ester, or alkyl as side chains, were synthesized by Stille coupling reaction. The structures of the polymers were confirmed, and their thermal, optical, electrochemical, and photovoltaic properties were investigated. The introduction of conjugated electron‐withdrawing OXD or formate ester side chain benefits to decrease the bandgaps of the polymers and improve the photovoltaic performance due to the low steric hindrance of BDT. Bulk heterojunction polymer solar cells (PSCs) were fabricated based on the blend of the as‐synthesized polymers and the fullerene derivative [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) in a 1:2 weight ratio. The maximum power conversion efficiency of 2.06% was obtained for PL5 ‐based PSC under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic properties of novel (X-DADAD)n conjugated polymers with fluorene and phenylene blocks

Novel fluorene- and phenylene-based conjugated polymers with the TBTBT molecular framework consisting of the thiophene (T) and benzothiadiazole (B) building blocks have been synthesized and investigated. It has been demonstrated that the variation of X building blocks with branched side chains in (X-TBTBT)_n-type structures, as well as the introduction of fluorine into the main chain, strongly affects the optical, electronic and physicochemical properties of the obtained polymers. The phenylene-based polymer with a fluorine- loaded TBTBT block achieves a power conversion efficiency of 7% in organic solar cells, which can be further improved by optimizing the active layer morphology.     

Synthesis and photovoltaic properties of two‐dimensional copolymers based on novel benzothiadiazole and quinoxaline acceptors with conjugated dithienylbenzothiadiazole pendants

Two novel acceptors of benzo[c][1,2,5]thiadiazole and quinoxaline with conjugated dithienylbenzothiadiazole pendants were first designed and synthesized for building efficient photovoltaic copolymers. Based on benzo[1,2‐b;3,4‐b′]dithiophene donors and the two acceptors, two new copolymers have been prepared by Stille coupling polymerization. The resulting copolymers were characterized by ¹H NMR, gel permeation chromatography, and thermogravimetric analysis. UV–Visible absorption and cyclic voltammetry measurements indicated that the two copolymers possessed strong and broad absorption in the range of 300–700 nm, and deep‐lying energy levels of highest occupied molecular orbitals. The polymer photovoltaic devices based on benzo[c][1,2,5]thiadiazole‐based copolymer/phenyl‐C₇₁‐butyric acid methyl ester exhibited a power conversion efficiency of 2.42%, attributed to its relatively better light‐harvesting ability and active film morphology. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 668–677     

A novel mesogen‐jacketed liquid crystalline electroluminescent polymer with both thiophene and oxadiazole in conjugated side chain

Mesogen‐jacketed liquid crystalline polymers (MJLCPs) with both electron‐transport oxadiazole and hole‐transport thiophene in the side chain were reported for their promising electroluminescent property. Monomers of 2,5‐bis{5‐[(4‐alkoxyphenyl)‐1,3,4‐oxadiazole]thiophen‐2‐yl}styrene (M‐Cm, m is the number of the carbons in the alkoxy groups, m = 8,10) were synthesized and confirmed by ¹H‐NMR, mass spectrometry, and elemental analysis. The corresponding polymers were successfully obtained and characterized by thermal analysis, optical spectroscopy, cyclic voltammetry, electroluminescent analysis, polarized light microscopy (PLM), and wide‐angle X‐ray diffraction (WAXD). The polymers exhibited high decomposition temperatures reaching 382 °C and high T_g's reaching 184 °C. The absorption spectra indicated that both the monomers and polymers had little aggregation in film than that in solution, and the absorption spectra of the polymers showed an obvious blue‐shift compared with those of the monomers. Both the monomers and the polymers had blue‐green emission, and the photoluminescence spectra of the polymers in film suggested the formation of excimer or exciplex. The polymers showed lower HOMO energy levels and LUMO energy levels than those of the MJLCPs containing oxadiazole unit reported before. Electroluminescence study with the device configuration of ITO/PEDOT/PVK/polymer/TPBI/Ca/Ag showed maximum brightness and current efficiency of 541 cd/m² and 0.10 cd/A, which proved that the introduction of directly connected electron‐ and hole‐transport units could greatly improve the EL property of side‐chain conjugated polymers. The phase structures of the polymers were confirmed to be smectic A phase through the results of PLM and WAXD. The annealed samples emitted polarized photoluminescence at room temperature, which indicated potential utility for practical applications in display. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1502–1515, 2010     

Low band‐gap D–A conjugated copolymers based on anthradithiophene and diketopyrrolopyrrole for polymer solar cells and field‐effect transistors

Two conjugated copolymers PADT‐DPP and PADT‐FDPP based on anthradithiophene and diketopyrrolopyrrole, with thiophene and furan as the π‐conjugated bridge, respectively, were successfully synthesized and characterized. The number‐averaged molecular weights of the two polymers are 38.7 and 30.2 kg/mol, respectively. Polymers PADT‐DPP and PADT‐FDPP exhibit broad absorption bands and their optical band gaps are 1.44 and 1.50 eV, respectively. The highest occupied molecular orbital energy level of PADT‐DPP is located at ?5.03 eV while that of PADT‐FDPP is at ?5.16 eV. In field‐effect transistors, PADT‐DPP and PADT‐FDPP displayed hole mobilities of 4.7 × 10^?3 and 2.7 × 10^?3 cm²/(V s), respectively. In polymer solar cells, PADT‐DPP and PADT‐FDPP showed power conversion efficiency (PCE) of 3.44% and 0.29%, respectively. Atomic force microscopy revealed that the poor efficiency of PADT‐FDPP should be related to the large two‐phase separation in its active layer. If 1,8‐diiodooctane (DIO) was used as the solvent additive, the PCE of PADT‐DPP remained almost unchanged due to very limited morphology variation. However, the addition of DIO could remarkably elevate the PCE of PADT‐FDPP to 2.62% because of the greatly improved morphology. Our results suggest that the anthradithiophene as an electron‐donating polycyclic system is useful to construct new D–A alternating copolymers for efficient polymer solar cells. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1652–1661     

Donor–acceptor photovoltaic polymers based on 1,4‐dithienyl‐2,5‐dialkoxybenzene with intramolecular noncovalent interactions

Donor–acceptor (D–A) conjugated polymers bearing non‐covalent configurationally locked backbones have a high potential to be good photovoltaic materials. Since 1,4‐dithienyl‐2,5‐dialkoxybenzene ( TBT ) is a typical moiety possessing intramolecular S…O interactions and thus a restricted planar configuration, it was used in this work as an electron‐donating unit to combine with the following electron‐accepting units: 3‐fluorothieno[3,4‐b]thiophene ( TFT ), thieno‐[3,4‐c]pyrrole‐4,6‐dione ( TPD ), and diketopyrrolopyrrole ( DPP ) for the construction of such D–A conjugated polymers. Therefore, the so‐designed three polymers, PTBTTFT , PTBTTPD , and PTBTDPP , were synthesized and investigated on their basic optoelectronic properties in detail. Moreover, using [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as acceptor material, polymer solar cells (PSCs) were fabricated for studying photovoltaic performances of these polymers. It was found that the optimized PTBTTPD cell gave the best performance with a power conversion efficiency (PCE) of 4.49%, while that of PTBTTFT displayed the poorest one (PCE = 1.96%). The good photovoltaic behaviors of PTBTTPD come from its lowest‐lying energy level of the highest occupied molecular orbital (HOMO) among the three polymers, and good hole mobility and favorable morphology for its PC₇₁BM‐blended film. Although PTBTDPP displayed the widest absorption spectrum, the largest hole mobility, and regular chain packing structure when blended with PC₇₁BM, its unmatched HOMO energy level and disfavored blend film morphology finally limited its solar cell performance to a moderate level (PCE: 3.91%). © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 689–698     

Quinoxaline‐based D‐A conjugated polymers for organic solar cells: Probing the effect of quinoxaline side chains and fluorine substitution on the power conversion efficiency

We describe the successful synthesis of four novel donor‐acceptor (D‐A) type copolymers, referred to as PQxBT , PQxFBT , TQxBT , and TQxFBT . The effects of using a fluorinated bithiophene (FBT) and varying the side‐chain moieties tethered to the quinoxaline (Qx) unit (electron‐withdrawing group in the polymer backbone) on the physical properties and photovoltaic performance were investigated. Specifically, the four polymers were synthesized using either alkoxyphenyl (P) or alkylthiophene (T) units anchored to the quinoxaline in the polymer backbone. The FBT‐bearing polymers, PQxFBT and TQxFBT , displayed more redshifted absorption spectra and higher crystallinity owing to the greater planarity of their polymer backbone as compared to the non‐fluorinated polymers. The TQxFBT copolymer, equipped with both the alkylthiophene side chains and FBT, exhibited face‐on orientation in film state and a well‐mixed nanophase morphology in TQxFBT :PC₇₁BM blend films. The photovoltaic device fabricated from TQxFBT :PC₇₁BM exhibited the highest power conversion efficiency of 4.18%. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 55, 1209–1218     

Synthesis and characterization of low‐band‐gap conjugated polymers containing phenothiazine and benzo‐2,1,3‐thia‐/seleno‐diazole

Two phenothiazine‐based conjugated polymers, poly(3, 7‐divinylene‐N‐octyl‐phenothiazine‐alt‐benzo‐2,1,3‐ thiadiazole) (PQS) and poly(3,7‐divinylene‐N‐octyl‐phenothiazine‐alt‐benzo‐2,1,3‐selenodiazole) (PQSe) were synthesized by Heck coupling reaction. The chemical structures of the two polymers were confirmed by ¹H‐NMR and Ft‐IR. They showed good solubility in some common organic solvents such as tetrahydrofuran (THF), chloroform. The weight‐average molecular weight (Mw) of the polymers determined by GPC in THF against polystyrene standards was 3.7 × 10³ for PQS and 1.9 × 10³ for PQSe, respectively. The temperatures of 5% weight loss (T₅) were 385.0°C for PQS and 324.0°C for PQSe, respectively, determined by TGA measurements under nitrogen ambience. UV–vis absorption spectra of the polymer films showed the absorption maxima at 537 nm for PQS and 539 nm for PQSe, with the full width at half maximum (FWHM) of 190 and 230 nm, respectively. The optical band gaps ( ) of the polymer films are 1.86 eV for PQS and 1.80 eV for PQSe, respectively. As the polymers have low‐band‐gap and broad absorption in the visible region, they may be used as potential light‐harvesting materials for photovoltaic devices (PVDs). Furthermore, photoluminescence (PL) spectra of the polymer solutions showed the emission maxima at 698 nm for PQS and 709 nm for PQSe, with FWHM of 152 nm and 167 nm, respectively, which revealed that these two polymers may be used as red and near infrared light‐emitting materials for polymeric light‐emitting diodes (PLEDs). Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and characterization of novel low‐bandgap triphenylamine‐based conjugated polymers with main‐chain donors and pendent acceptors for organic photovoltaics

A series of novel low‐bandgap triphenylamine‐based conjugated polymers ( PCAZCN , PPTZCN , and PDTPCN ) consisting of different electron‐rich donor main chains (N‐alkyl‐2,7‐carbazole, phenothiazine, and cyclopentadithinopyrol, respectively) as well as cyano‐ and dicyano‐vinyl electron‐acceptor pendants were synthesized and developed for polymer solar cell applications. The polymers covered broad absorption spectra of 400–800 nm with narrow optical bandgaps ranging 1.66–1.72 eV. The highest occupied molecular orbital and lowest unoccupied molecular orbital levels of the polymers measured by cyclic voltammetry were found in the range of ?5.12 to ?5.32 V and ?3.45 to ?3.55 eV, respectively. Under 100 mW/cm² of AM 1.5 white‐light illumination, bulk heterojunction photovoltaic devices composing of an active layer of electron‐donor polymers ( PCAZCN , PPTZCN , and PDTPCN ) blended with electron‐acceptor [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester or [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) in different weight ratios were investigated. The photovoltaic device containing donor PCAZCN and acceptor PC₇₁BM in 1:2 weight ratio showed the highest power conversion efficiency of 1.28%, with V_oc = 0.81 V, J_sc = 4.93 mA/cm², and fill factor = 32.1%. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and photovoltaic properties of conjugated side chains polymers with different electron‐withdrawing and donating end groups

A series of novel low band gap polymers containing conjugated side chains with 4,7‐dithien‐5‐yl‐2,1,3‐benzodiathiazole and different electron‐withdrawing end groups of aldehyde ( PT‐DTBTCHO ), 2‐ethylhexyl cyanoacetate ( PT‐DTBTCN ), 1,3‐diethyl‐2‐thiobarbituric acid ( PT‐DTBTDT ), and electron‐donating end group of 2‐methylthiophene ( PT‐DTBTMT ) have been designed and synthesized. All polymers exhibit good solubility in common organic solvents, film‐forming ability, and thermal stability. These conjugated polymers show the broad ultraviolet‐visible absorption and the narrow optical band gaps in the range of 1.65–1.90 eV. Through changing the end group of conjugated side chains, the photophysical properties and energy levels of the polymers were tuned effectively. Bulk heterojunction solar cells based on the blend of these polymers and (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) reached the best power conversion efficiency (PCE) of 2.72%. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

3,6‐Dialkylthieno[3,2‐b]thiophene moiety as a soluble and electron donating unit preserving the coplanarity of photovoltaic low band gap copolymers

It has been shown recently, that the presence of alkyl side chains at the 3‐positions on the thiophene rings placed next to 2,1,3‐benzothiadiazole core in the backbone of several conjugated polymers results in severe steric hindrance and prevents efficient planarity of the thiophene‐2,1,3‐benzothiadiazole‐thiophene (TBzT) segment. Both properties have a strong influence on the optoelectronic properties of the polymer and need to be considered when the polymer is to be used for organic electronics applications. In this work, we modified a previously synthesized oligothiophene copolymer, consisting of two 3,4′‐dialkyl‐2,2′‐bithiophene units attached to a 2,1,3‐benzothiadiazole unit (TBzT segment) and a thieno[3,2‐b]thiophene unit, by optimizing the lateral alkyl side chains following a density functional theory investigation. It is demonstrated that eliminating the alkyl side chains from the 3‐positions of the TBzT segment and anchoring them onto the thieno[3,2‐b]thiophene, using an efficient synthesis of the 3,6‐dihexylthieno[3,2‐b]thiophene unit, allows us to reduce the energy band gap. In addition, the chemical modification leads to a better charge transport and to an enhanced photovoltaic efficiency of polymer/fullerene blends. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Low band‐gap diketopyrrolopyrrole‐containing polymers for near infrared electrochromic and photovoltaic applications

Donor–acceptor type polymers bearing diketopyrrolopyrrole and 3,4‐ethylenedioxythiophene units are reported. The polymers are green and exhibit very low band‐gaps (1.19 eV) with strong and broad absorption (maxima of about 830 nm) in the near infrared (NIR) region in their neutral film states. The polymers display color changes between dark green and light blue with exceptional optical contrasts in the NIR regions of up to 78 and 63% as thin films and single‐layer electrochromic devices, respectively. Fast switching, good stabilities as well as high coloration efficiencies (743–901 cm² C^?1) were also observed. The polymers could also be potentially used as photovoltaic material, with a power conversion efficiency of up to 1.68%. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1287–1295