Stretchable and flexible resistive behavior of poly(3,4‐ethylenedioxythiophene):Poly(styrenesulfonate) thin film on ultra‐low modulus polydimethylsiloxane with trench‐type roughness

This study investigates the resistive behavior of rod‐coated micrometer thick films of poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) on ultra‐low modulus (120– 130 kPa) polydimethylsiloxane (PDMS) substrate having scratch or microtrench‐type roughness patterns. On average, the films were found to remain electrically functional up to 23% axial strain with an average increase of three times in the value of the normalized resistance. The films were also found to remain conductive up to bending diameter of 4 mm with an average increase of 1.12 times their initial resistance. The rod‐coated PEDOT:PSS films on ultra‐low modulus PDMS having microtrench‐type roughness were also found to remain functional even after 1000 bending cycles at a bending diameter of 4 mm and even smaller with an increase in resistance that was on average 1.15 times their initial resistance. The films were found to fail firstly by cracking and thereby debonding from the substrate under the application of axial strain. On the other hand, the films exhibit no delamination under bending strains. The results from this investigation suggest that the polymer–polymer laminate has potential applicability in stretchable and flexible electronics and related applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 226–233     

Growth of poly(3,4‐ethylenedioxythiophene) films prepared by base‐inhibited vapor phase polymerization

Transparent [90% transmittance at 550 nm at a sheet resistance (R_s) of 279 Ω sq^?1] poly(3,4‐ethylenedioxythiophene) (PEDOT) films with electrical conductivities up to 1354 S cm^?1 are prepared using base‐inhibited vapor phase polymerization at atmospheric pressure. The influence of reaction conditions, such as temperature and growth time, on the film formation is investigated. A simple and convenient two‐electrode method is used for the in situ measurement of resistance, enabling to investigate the growth mechanism of polymer films and the influence of different parameters (relative humidity and the amount of oxidant) on the film growth. Low humidity exerts a detrimental effect on film growth and conductivity. In situ R_s measurements suggest that a large structural change occurs upon washing the PEDOT‐oxidant film. © 2014 Wiley Periodicals, Inc. J Polym Sci Part B: Polym. Phys. 2014 , 52, 561–571     

Improved Electrochromic Performance of Poly(3,4‐ethylenedioxythiophene) by Incorporating a Three‐Dimensionally Ordered Macroporous Structure

In this paper, three‐dimensionally ordered macroporous (3DOM) poly(3,4‐ethylenedioxythiophene) (PEDOT) films were electropolymerized from an ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate ([Bmim]PF₆). The electrochromic performances of the 3DOM PEDOT films were studied. The 3DOM films exhibited high transmittance modulation (41.2 % at λ=580 nm), high ionic fast switching speeds (0.7 and 0.7 s for coloration and bleaching, respectively), and enhanced cycling stability relative to that exhibited by the dense PEDOT film. The relationship between the declining behavior of the transmittance modulation and the nanostructure of the film was investigated. A three‐period decay process was proposed to understand the declining behavior. The 3D interconnected macroporous nanostructure is beneficial for fast ion and electron transportation, high ion accessibility, and maintenance of structure integrity, which result in enhanced cycling stability and fast switching speeds.     

Smectic structures in electrochemically prepared poly(3,4‐ethylenedioxythiophene) films

Sub‐micrometer layers of electrochemically prepared methyl‐ and decyl‐substituted poly(3,4‐ethylenedioxythiophene) (PEDOT) carrying perchlorate counterions have been examined with grazing incidence X‐ray diffraction with synchrotron radiation. The materials were found to be partially crystalline, and the data could be ascribed to a model of sheets of π‐π stacked polymer chains with a smectic ordering of these sheets. An unsubstituted PEDOT sample with the polymeric polystyrenesulfonic acid as a counterion was also investigated and turned out to be essentially amorphous. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 945–952, 2003     

Structure and morphology control in thin films of regioregular poly(3‐hexylthiophene)

This review focuses on the structural control in thin films of regioregular poly(3‐hexylthiophene) (P3HT), a workhorse among conjugated semiconducting polymers. It highlights the correlation existing between processing conditions and the resulting structures formed in thin films and in solution. Particular emphasis is put on the control of nucleation, crystallinity and orientation. P3HT can generate a large palette of morphologies in thin films including crystalline nanofibrils, spherulites, interconnected semicrystalline morphologies and nanostructured fibers, depending on the elaboration method and on the macromolecular parameters of the polymer. Effective means developed in the recent literature to control orientation of crystalline domains in thin films, especially by using epitaxial crystallization and controlled nucleation conditions are emphasized. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1218–1233, 2011     

Crystallinity of poly(3‐hexylthiophene) in thin films determined by fast scanning calorimetry

Using fast scanning calorimetry, we determined the crystallinity of thin films of poly(3‐hexylthiophene) crystallized from the melt from measurements of the specific melting enthalpy. A broad range of film thicknesses from 10 µm down to 26 nm was covered. The sample mass was determined from measurements of the specific heat capacity in the molten state allowing a quantitative analysis of the heat flow data. Films with a thickness 400 nm slowly cooled from the melt showed the same crystallinity as bulk samples measured with conventional DSC. Below 350 nm the melting enthalpy decreased strongly. We assign this strongly reduced crystallinity to the restricted crystallization kinetics originating from hindered spherulitic growth under thin film confinement. A higher crystallinity could be partially regained by extended isothermal crystallization at elevated temperatures. Much faster cooling, with rates above about 100 Ks^?1 led to a partial suppression of crystallization even for thick films. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1791–1801     

Poly(3,4‐ethylenedioxythiophene)‐based copolymers for biosensor applications

The synthesis of 3,4‐ethylenedioxythiophene (EDOT) derivatives bearing functional groups is described. Their electrochemical characteristics were investigated with cyclic voltammetry and ultraviolet–visible spectroscopy. Various copolymers of EDOT and modified EDOT containing hydroxyl groups were electrochemically prepared. The ability to bind proteins to the surface of these copolymers was investigated through the covalent coupling of glucose oxidase. The obtained materials were used as working electrodes and were shown to be able to amperometrically detect glucose under aerobic and anaerobic conditions. Possible applications of these materials as biosensors are discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 738–747, 2002; DOI 10.1002/pola.10159     

Efficient enhancement of the thermoelectric performance of vapor phase polymerized poly(3,4‐ethylenedioxythiophene) films with poly(ethyleneimine)

Tuning the molecular rearrangement and oxidation level has been proven to be effective strategies for optimizing the thermoelectric (TE) performance of PEDOT. It is difficult to achieve these effects simultaneously via a one‐step process, however. In this work, we combined vapor phase polymerization (VPP) and H₂SO₄ post‐treatment to obtain a highly conductive PEDOT film. A novel strategy using polyethylenemine (PEI) as an effective reducing agent was employed to enhance the thermopower of the PEDOT film. Grazing‐Incidence Wide‐Angle X‐ray Scattering analysis and the changes in the oxidation level allow us to elucidate the role of PEI and its transport mechanism. It is demonstrated that the thermopower of well‐ordered crystallites in the PEDOT film significantly increases more than five times (from 11 to 59 μV K^?1) by the PEI‐DMF solution immersion process, while the electrical conductivity is maintained at 100 S cm^?1. The promising method connecting VPP, H₂SO₄, and PEI shows great potential for effectively tuning the thermopower of organic TE materials. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 257–265     

Poly(3,4-ethylenedioxythiophen)/Poly(4-styrenesul-fonate): Thin Films and Microfibers

This Feature Article describes our recent researches on processing poly(3,4-ethylenedioxythiophene /poly(4-styrenesulfonate) (PEDOT/PSS) colloidal dispersion into thin films which exhibit high conductivity and high transparency, and into microfibers which exhibit high conductivity and high mechanical strength. The state-of-the-art thin films and microfibers are expected to utilize to sophisticated touch screens and wearable electronic devices as organic transparent electrodes and woven electric circuits, respectively.     

Aminosilane SAM‐Assisted Patterning of Poly(3,4‐ethylenedioxythiophene) Nanofilm Robustly Adhered to SiO2 Substrate

To improve the patternability and adhesion of poly(3,4‐ethylenedioxythiophene) (PEDOT) nanofilm to an SiO₂ surface, an oxidized silicon wafer substrate was microcontact printed with an octadecyltrichlorosilane (OTS) monolayer, and subsequently its negative pattern was self‐assembled with (3‐aminopropyl)trimethoxysilane (APS) molecules. Then, a PEDOT nanofilm was selectively grown on the APS monolayer‐patterned area via the vapor phase polymerization (VPP) method. To evaluate the adhesion and patterning, the PEDOT nanofilm and mixed monolayer were investigated with a Scotch® tape peel test, Fourier transform infrared (FT‐IR) microspectrometer, X‐ray photoelectron spectrometer, and optical and atomic force microscopes. The evaluation revealed that the newly developed bottom‐up process can offer a robustly adhered, and selectively patterned PEDOT nanofilm on an oxidized Si wafer surface, most likely through extensive but intermittent chemical bonds between the polymer and the APS monolayer.

     

Synthesis of Poly(3,4‐ethylenedioxythiophene) latexes using poly(N‐vinylpyrrolidone)‐based copolymers as reactive stabilizers

The synthesis by oxidative polymerization of well‐defined poly(3,4‐ethylenedioxythiophene) (PEDOT) nano‐objects in the presence of modified and unmodified poly(N‐vinylpyrrolidone)‐based copolymers used as stabilizers in aqueous media is reported. Ammonium persulfate or a mixture of ammonium persulfate with CuCl₂ or CuBr₂ was used as oxidants. The effects of several parameters such as the molar mass and the concentration of the stabilizer as well as the nature of the oxidants on the size, morphology, and the conductivity of the PEDOT particles have been investigated. The distribution of the reactive moieties along the copolymer stabilizer backbone was shown to be crucial to get well‐defined PEDOT nano‐objects. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3841–3855, 2010     

Suppression of Thermochromism in a Poly(di‐n‐hexylsilane)‐Zirconia Hybrid

Summary: Poly(di‐n‐hexylsilane) (PDHS)‐containing zirconia hybrid thin films were prepared by a sol‐gel reaction of PDHS copolymers and zirconium alkoxide, and it was found that the thermochromic properties of PDHS due to the transformation of the Si Si main chain were suppressed in the PDHS‐zirconia hybrid thin film.

Structure of poly(di‐n‐hexylsilane)‐zirconia hybrid.     

Electrochromic enhancement of poly(3,4‐ethylenedioxythiophene) films functionalized with hydroxymethyl and ethylene oxide

2‐((2,3‐Dihydrothieno[3,4‐b]dioxin‐2‐yl)methoxy)methyl oxirane (EDOT‐MO) was successfully synthesized by the reaction of epichlorohydrin with hydroxymethylated‐3,4‐ethylenedioxylthiophene (EDOT‐MeOH), which was synthesized via a simple four‐step sequence. Poly(hydroxymethylated‐3,4‐ethylenedioxylthiophene) (PEDOT‐MeOH) and poly(2‐((2,3‐dihydrothieno[3,4‐b]dioxin‐2‐yl)methoxy)methyl oxirane) (PEDOT‐MO) were electrosynthesized through electropolymerization of EDOT‐MeOH and EDOT‐MO, respectively. Structural, electrochemical, optical, and thermal properties of as‐formed polymers were investigated by FTIR, cyclic voltammetry, UV–vis, and thermogravimetry. Spectroelectrochemistry studies demonstrated that PEDOT‐MeOH and PEDOT‐MO could be reversibly oxidized and reduced accompany with obvious color changes. Further kinetic studies demonstrated that the introduction of hydroxymethyl or ethylene oxide group significantly improved electrochromic properties of 3,4‐ethylenedioxythiophene (PEDOT) and resulted in high contrast ratios (57.3% at 585 nm) and coloration efficiencies (338.5 cm² C^?1), low switching voltages, and fast response time. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1989–1999     

Layer‐by‐layer ionomer films made from poly(styrene‐co‐styrenesulfonic acid) and poly(methyl methacrylate‐co‐4‐vinylpyridine) in tetrahydrofuran

Thin films were fabricated layer‐by‐layer (LbL) via ionic bonds formed between a cationic ionomer and an anionic ionomer, which were produced via proton transfer from poly(styrene‐co‐styrenesulfonic acid) to poly(methyl methacrylate‐co‐4‐vinylpyridine) in an organic solvent, tetrahydrofuran. Ionic contents of the ionomers were very low down to 5.6 mol %, much lower than usual polyelectrolytes. The build up of the LbL films was demonstrated by UV/vis spectroscopy: the absorbance of the phenyl rings in styrene residues increased with the number of depositions (thus the number of layers). Transmission electron microscopy observation of strained thin films showed unique deformation mode, involving many bands that developed both in the parallel and perpendicular directions to the stress axis. This is quite different from the deformation modes seen for ionomer blend films and for coextruded polystyrene/poly(methyl methacrylate) multilayer tapes. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 50: 101–105, 2012     

Improvement in carrier mobility of poly(3,4‐ethylenedioxythiophene) nanowires synthesized in porous alumina templates

Polymeric nanowires of poly(3,4‐ethylenedioxythiophene) (PEDOT) are electrochemically synthesized using porous anodic alumina oxide (AAO) membranes as templates. Four‐point resistivity measurements on more than 100 PEDOT nanowires with different diameters (50–250 nm) reveal a statistically significant size‐dependent phenomenon in which the nanowires with a smaller diameter exhibit higher conductivity. Structural characterization with Raman spectroscopy and doping level estimation with energy‐dispersive X‐ray spectrometry and X‐ray photoelectron spectroscopy indicate that the observed conductivity enhancement can be attributed to improved carrier mobility in PEDOT nanowires having an elongated conjugation structure because of the effect of the AAO template. From the estimated doping levels (～5%) and conductivity data (～100 S/cm), it is found that the carrier mobility reach 2.0 cm²/V s for the nanowire with the smallest diameter, as compared with 4.0 × 10^?4 cm²/V s for a bulk PEDOT film. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Multi‐Sensitive Microgels Filled with Conducting Poly(3,4‐ethylenedioxythiophene) Nanorods

In this work we describe the synthesis of multi‐sensitive aqueous microgel particles with incorporated conducting poly(3,4‐ethylenedioxythiophene) (PEDOT) nanorods. We demonstrate that the loaded amount of PEDOT nanorods as well as their morphology can be varied by controlling the reaction conditions such as monomer concentration and alcohol concentration in aqueous phase. Obtained microgels can be stimulated by changes in the environment temperature as well as by the repulsion/attraction forces within polymeric network due to the reversible oxidation/reduction of the conjugated polymer. Microgels with unique properties can be operated in colloidal systems or used as building blocks for the preparation of nanostructured films.

     

Poly(3,4‐ethylenedioxythiophene) Derived from Poly(ionic liquid) for the Use as Hole‐Injecting Material in Organic Light‐Emitting Diodes

We report that poly(3,4‐ethylenedioxythiophene) derived from poly(ionic liquid) (PEDOT:PIL) constitutes a unique polymeric hole‐injecting material capable of improving device lifetime in organic light‐emitting diodes (OLEDs). Imidazolium‐based poly(ionic liquid)s were engineered to impart non‐acidic and non‐aqueous properties to PEDOT without compromising any other properties of PEDOT. A fluorescent OLED was fabricated using PEDOT:PIL as a hole‐injection layer and subjected to a performance evaluation test. In comparison with a control device using a conventional PEDOT‐based material, the device with PEDOT:PIL was found to achieve a significant improvement in terms of device lifetime. This improvement was attributed to a lower indium content in the PEDOT:PIL layer, which can be also interpreted as the effective protection characteristics of PEDOT:PIL for indium extraction from the electrodes.

     

Thermoelectric properties of nanocomposite thin films prepared with poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) and graphene

Carbon nanotubes (CNTs), either single wall carbon nanotubes (SWNTs) or multiwall carbon nanotubes (MWNTs), can improve the thermoelectric properties of poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT?:?PSS), but it requires addition of 30-40 wt% CNTs. We report that the figure of merit (ZT) value of PEDOT?:?PSS thin film for thermoelectric property is increased about 10 times by incorporating 2 wt% of graphene. PEDOT?:?PSS thin films containing 1, 2, 3 wt% graphene are prepared by solution spin coating method. X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy analyses identified the strong π-π interactions which facilitated the dispersion between graphene and PEDOT?:?PSS. The uniformly distributed graphene increased the interfacial area by 2-10 times as compared with CNT based on the same weight. The power factor and ZT value of PEDOT?:?PSS thin film containing 2 wt% graphene was 11.09 μW mK(-2) and 2.1 × 10(-2), respectively. This enhancement arises from the facilitated carrier transfer between PEDOT?:?PSS and graphene as well as the high electron mobility of graphene (200,000 cm(2) V(-1) s(-1)). Furthermore the porous structure of the thin film decreases the thermal conductivity resulting in a high ZT value, which is higher by 20% than that for a PEDOT?:?PSS thin film containing 35 wt% SWNTs.     

Control of doctor‐blade coated poly (3,4‐ethylenedioxythiophene)/poly(styrenesulfonate) electrodes shape on prepatterned substrates via microflow control in a drying droplet

We demonstrated a simple patterning method for the deposition of polymer electrodes such as poly(3,4‐ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT/PSS). We made use of the difference in wettability between hydrophobic surfaces and hydrophilic surfaces to make the patterns. However, the patterns made with our patterning method created undesirable ring‐like stains, which were caused by the outward flow of the solute within the PEDOT/PSS solution drop. To achieve homogenous device performance, we proposed a simple process for removing this ring‐like stain by making the surface tension gradient with dual solvent system in the PEDOT/PSS solution drop. Because this surface tension gradient causes the inward flow of the solute within the PEDOT/PSS solution drop, the ring‐like stain is removed. Finally, we confirmed the potential of our patterning method for polymer electrodes such as the PEDOT/PSS by fabricating pentacene thin‐film transistors (TFTs) and measuring the electrical properties of the pentacene TFTs. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1590–1596, 2011