Structure and mechanical properties for binary blends of polypropylene and ethylene‐1‐hexene copolymer

The structure and mechanical properties of the injection‐molded products for the binary blends composed of an isotactic polypropylene (PP) and a rubbery ethylene‐1‐hexene copolymer (EHR) were studied. The following two types of blends were employed: one is the incompatible blend of PP and ethylene‐rich EHR; the other is the compatible blend of PP and 1‐hexene‐rich EHR. The incompatible blend shows a phase‐separated morphology, in which EHR domains in the skin layer highly orient to the flow direction. On the other hand, the compatible blend shows fairly homogeneous morphology in the skin and core regions, in which EHR molecules are dissolved into the amorphous PP region. The measurements of birefringence and infrared dichroism revealed that the magnitude of molecular orientation along the flow direction for the compatible blend is larger than that for the incompatible blend. Nevertheless, it was also found that anisotropy of the mechanical properties for the compatible blend is less prominent, which is attributed to lack of the mechanical connection between neighbor crystalline fragments aligned perpendicular to the flow direction. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 701–713, 1999     

Thermoplastic blend demixing by a high‐pressure,high‐temperature process

The analysis of a thermoplastic polymer blend requires a precise separation of the blend components, which is usually performed by selective solvent extraction. However, when the components are high‐molecular‐weight polymers, a complete separation is very difficult. The use of fluids in near critical and supercritical conditions becomes a promising alternative to reach a much more precise separation. In this work, a method to separate reactive and physical blends from high‐molecular‐weight commercial polymers is proposed. Polyethylene (PE)/polystyrene (PS) blends were separated into their components with n‐propane, n‐pentane, and n‐heptane at near critical and supercritical conditions. The selectivity of each solvent was experimentally studied over a wide range of temperatures for assessing the processing windows for the separation of pure components. The entire PE phase was solubilized by n‐pentane and n‐heptane at similar temperatures, whereas propane at supercritical conditions could not dissolve the fraction of high‐molecular‐weight PE. The influence of the blend morphology and composition on the efficiency of the polymer separation was studied. In reactive blends, the in situ copolymer formed was solubilized with the PE phase by chemical affinity. The method proposed for blend separation is easy, rapid, and selective and seems to be a promising tool for blend separation, particularly for reactive blends, for which the isolation of the copolymer is essential for characterization © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2361–2369, 2005     

Phase separation of off‐critical polymer blends of poly(styrene‐co‐maleic anhydride) and poly(methyl methacrylate). II. Morphology and mechanical properties

The effects of the phase‐separation temperature and time on the mechanical properties and morphology of poly(methyl methacrylate)/poly(styrene‐co‐maleic anhydride with 10 wt% ethyl acrylate) (SMA) blends were studied. Two compositions (20/80 and 40/60 w/w SMA/PMMAe) were prepared with a miniature twin‐screw extruder. Compared with those of the miscible blends, the Young's modulus values of the blends increased after the phase separation of the 40/60 SMA/PMMAe blend and within the early stage of spinodal decomposition of the 20/80 SMA/PMMAe blend. The mechanical properties, in terms of the tensile strength at break and the elongation, were better for the miscible blends than for the phase‐separation blends. This was believed to be the result of changes in the composition and molecular reorganization. The changes in the phase‐separating domains of both compositions, as observed by transmission electron microscopy, had no significant influence on the tensile moduli. Detailed studies of the morphology revealed a cocontinuous structure, indicating that the blends underwent spinodal decomposition. A morphological comparison of the two compositions illustrated the validity of the level rule. The growth rate of the droplet size was determined by approximation from the light scattering data and by direct measurements with transmission electron microscopy. The discrepancies observed in the droplet size growth rate were attributed to heat variations induced by the different sample thicknesses and heat transfer during the investigation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 886–897, 2004     

Local deformation in photo‐crosslinked polymer blends monitored by Mach‐Zehnder interferometry

Local deformation of a polymer mixture crosslinked by irradiation with ultraviolet light was in situ monitored by using a Mach‐Zehnder interferometer. In combination with the refractive index data obtained from independent measurements, the deformation in the nanometer scales of the crosslinked blends was calculated by using the difference in optical path length of the blend measured before and after irradiation. Upon varying the crosslink density of the blend by changing the light intensity, it was found that the local deformation well correlates with the crosslink density obtained from the reaction kinetics experiments. Furthermore, the strain relaxation of the blends was also monitored in situ and analyzed after irradiation over different time intervals. The results obtained in this study reveal the possibility of monitoring the nanometer‐scale deformation in polymers during radiation curing. These data also provide important information on the correlations between the irradiation‐induced elastic strain and the resulting morphology of reacting polymer blends. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2898–2913, 2005     

Importance of domain purity in semi‐conducting polymer/insulating polymer blends transistors

Printed electronics is a rapidly developing field of research which covers any electronic devices or circuits that can be processed using direct printing techniques. Among those printing techniques, inkjet printing is a technique of increasing interest for organic field‐effect transistors (FETs) due to its fully data driven and direct patterning. In this work, the morphology of semi‐conducting polymer/insulating polymer blends from inkjet printing and their FET properties have been investigated. We attempted to optimize the morphology of the blends by the addition of a co‐solvent to the blend solution prior to film deposition. By varying the boiling temperature of the co‐solvent, blend films are fabricated with varying domain purity and different degree of semi‐conducting polymer ordering. The morphologies of all the as‐cast samples from inkjet printing and subsequently thermally annealed samples are characterized by grazing incidence wide angle x‐ray scattering and small angle neutron scattering. The results indicate that the sample where a low boiling temperature co‐solvent is used exhibits a lower degree of semi‐conducting polymer ordering and less pure domains, resulting in a decrease of hole mobility. The morphologies that are formed when high boiling temperature co‐solvent is used, however, give a higher degree of semi‐conducting polymer ordering along with higher domain purity, significantly improving hole mobility up to 1.44 cm² V^?1 s^?1 at V_DS = 40 V. More importantly, with thermal annealing, all the samples exhibit similar semi‐conducting polymer ordering and domain sizes while the domain purity significantly varies. This work is a unique example that demonstrates the importance of domain purity in the optimization of morphology and FET performance, which is previous unavailable. It also provides a novel process that can efficiently control the morphology of semi‐conducting polymer/insulating polymer mixtures during deposition to maximize FET performance from inkjet printing. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1760–1766     

Thin films of PS/PS‐b‐pnipam and ps/pnipam polymer blends with tunable wettability

We developed thin films of blends of polystyrene (PS) with the thermoresponsive polymer poly(N‐isopropylacrylamide) (PNIPAM) (PS/PNIPAM) and its diblock copolymer polystyrene‐b‐poly(N‐isopropylacrylamide) (PS/PS‐b‐PNIPAM) in different blend ratios, and we study their surface morphology and thermoresponsive wetting behavior. The blends of PS/PNIPAM and PS/PS‐b‐PNIPAM are spin‐casted on flat silicon surfaces with various drying conditions. The surface morphology of the films depends on the blend ratio and the drying conditions. The PS/PS‐b‐PNIPAM films do not show an increase in their water contact angles with temperature, as it is expected by the presence of the PNIPAM block. All PS/PNIPAM films show an increase in the water contact angle above the lower critical solution temperature of PNIPAM, which depends on the ratio of PNIPAM in the blend and is insensitive to the drying conditions of the films. The difference between the wetting behavior of PS/PS‐b‐PNIPAM and PS/PNIPAM films is due to the arrangement of the PNIPAM chains in the film. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 670–679     

Dynamic mechanical behavior of acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The dynamic mechanical behavior of uncrosslinked (thermoplastic) and crosslinked (thermosetting) acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends was studied with reference to the effect of blend ratio, crosslinking systems, frequency, and temperature. Different crosslinked systems were prepared using peroxide (DCP), sulfur, and mixed crosslink systems. The glass‐transition behavior of the blends was affected by the blend ratio, the nature of crosslinking, and frequency. sThe damping properties of the blends increased with NBR content. The variations in tan δ_max were in accordance with morphology changes in the blends. From tan δ values of peroxide‐cured NBR, EVA, and blends the crosslinking effect of DCP was more predominant in NBR. The morphology of the uncrosslinked blends was examined using scanning electron and optical microscopes. Cocontinuous morphology was observed between 40 and 60 wt % of NBR. The particle size distribution curve of the blends was also drawn. The Arrhenius relationship was used to calculate the activation energy for the glass transition of the blends, and it decreased with an increase in the NBR content. Various theoretical models were used to predict the modulus of the blends. From wide‐angle X‐ray scattering studies, the degree of crystallinity of the blends decreased with an increasing NBR content. The thermal behavior of the uncrosslinked and crosslinked systems of NBR/EVA blends was analyzed using a differential scanning calorimeter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1556–1570, 2002     

Chemical and morphological evolution of PA‐6/Epm/Epm‐g‐MA blends in a twin screw extruder

Chemical conversion and morphological evolution of PA‐6/EPM/EPM‐g‐MA blends along a twin screw extruder were monitored by quickly collecting small samples from the melt at specific barrel locations. The results show that the MA content of all blends decreases drastically in the first zone of the extruder, i.e., upon melting of the blend components. Significant changes in morphology are also observed at this stage. A correlation between chemistry and morphology could thus be established. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1311–1320, 1999     

Morphology engineering of a novel poly(L‐lactide)/poly(1,5‐dioxepan‐2‐one) microsphere system for controlled drug delivery

Morphology is presented as a powerful tool to control the in vitro degradation and drug release characteristics of novel drug delivery microspheres prepared from homopolymer blends of 1,5‐dioxepan‐2‐one, DXO, and L ‐lactide, L‐LA. Their performance in this respect was compared to analogous P(L‐LA‐co‐DXO) microspheres. Blends formed denser and less porous microspheres with a higher degree of matrix crystallinity than copolymers of corresponding L‐LA:DXO composition. The morphology differences of blends and copolymers, further adjustable by means of component ratio, are shown to have a vital impact on the in vitro performance. Sustained drug delivery was obtained from both copolymers and blends. Molecular weight loss was retarded and diffusion‐mediated release was inhibited in the latter case, further delaying the release process. The effects of storage on the physicochemical properties of these systems were evaluated under desiccated and moist conditions for 5 months. Storage‐induced physicochemical changes, such as matrix crystallization and molecular weight decrease, were accelerated at higher relative humidities. P(L‐LA‐co‐DXO) demonstrated higher moisture sensitivity than a PLLA‐PDXO blend of corresponding composition. The more crystalline and dense morphology of blend microspheres may thus be considered an improvement of the storage stability. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 786–796, 2000     

Temperature‐dependent phase‐segregation behavior and antifouling performance of UV‐curable methacrylated PDMS/PEG coatings

Controllable phase segregation adjustment for immiscible polymer blends has always been tough, which hinders the development of amphiphilic antifouling coatings from more accessible blends. Herein, methacrylated poly(dimethylsiloxane) (PDMS‐MA) was synthesized and mixed with poly(ethylene glycol)methylether methacrylate (PEG‐MA). It was interestingly discovered that these PDMS‐MA/PEG‐MA blends displayed upper critical solution temperatures (UCST) due to thermo‐induced conformational change of PEG‐MA and the UCST changed with PDMS‐MA/PEG‐MA mass ratios. Micro‐/nano‐phase segregation, nanophase segregation, or homogenous morphology were therefore achieved. These PDMS‐MA/PEG‐MA blends with different mass ratios were UV‐cured under varying temperatures to fabricate coatings. Their surface morphology and wettability are readily adjusted by phase segregation. For the first time, highly hydrophilic surface was achieved for coatings with microphase segregation because of the exposure of PEG‐rich domains, which exhibited an enhanced protein resistance against bovine serum albumin (BSA). Anti‐bacterial performance (Shewanella loihica) was also observed for these PDMS/PEG coatings. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1612–1623     

Effect of PBT molecular weight and reactive compatibilization on the dispersed‐phase coalescence of PBT/SAN blends

Poly(butylene terephthalate) (PBT)/styrene‐acrylonitrile copolymer (SAN) blends were investigated with respect to their phase morphology. The SAN component was kept as dispersed phase and PBT as matrix phase and the PBT/SAN viscosity ratio was changed by using different PBT molecular weights. PBT/SAN blends were also compatibilized by adding methyl methacrylate‐co‐glycidyl methacrylate‐co‐ethyl acrylate terpolymer, MGE, which is an in situ reactive compatibilizer for melt blending. In noncompatibilized blends, the dispersed phase particle size increased with SAN concentration due to coalescence effects. Static coalescence experiments showed evidence of greater coalescence in blends with higher viscosity ratios. For noncompatibilized PBT/SAN/MGE blends with high molecular weight PBT as matrix phase, the average particle size of SAN phase does not depend on the SAN concentration in the blends. However noncompatibilized blends with low molecular weight PBT showed a significant increase in SAN particle size with the SAN concentration. The effect of MGE epoxy content and MGE molecular weight on the morphology of the PBT/SAN blend was also investigated. As the MGE epoxy content increased, the average particle size of SAN initially decreased with both high and low molecular weight PBT phase, thereafter leveling off with a critical content of epoxy groups in the blend. This critical content was higher in the blends containing low molecular weight PBT than in those with high molecular weight PBT. At a fixed MGE epoxy content, a decrease in MGE molecular weight yielded PBT/SAN blends with dispersed nanoparticles with an average size of about 40 nm. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Influence of Domain Size on Toughness of Poly(styrene‐block‐butadiene) Star Block Copolymer/Polystyrene Blends

Summary: The toughness of poly(styrene‐block‐butadiene) star block copolymer/polystyrene (PS) blends have been investigated using the essential‐work‐of‐fracture approach. The blends show a co‐continuous or layer‐like structure of polystyrene‐rich and polybutadiene‐rich domains arising from the used extrusion process. A tough‐to‐brittle transition at a critical domain size of polystyrene‐rich domains of about 50 nm and a maximum in the non‐essential work of fracture at 20–30% PS (co‐continuous morphology) have been found.

Non‐essential work of fracture as a function of the mean thickness of polystyrene‐rich domains, demonstrating a tough‐to‐brittle transition at a critical domain thickness about 50 nm. AFM micrograph of a star block copolymer/PS‐blend containing 40% PS.     

NMR study of the nanomorphology in thin films of polymer blends used in organic PV devices: MDMO‐PPV/PCBM

The disclosure of the nanomorphology of thin films in organic solar cells, prepared from blends of conjugated polymers and PCBM, is of key importance for a better understanding of the occurring photovoltaic (PV) mechanisms. Hereto solid‐state NMR relaxometry has been evaluated as a complementary technique to traditional microscopic techniques like atomic force microscopy and transmission electron microscopy. It is demonstrated that proton wide‐line solid‐state NMR relaxometry is a useful and innovative tool to study the phase morphology of blends used in semi‐conducting polymer based PV devices. Attention is focused on the influence of the blend composition and casting conditions on the resulting phase morphology. Two different casting techniques, i.e. spincoating and Doctor Blading, were compared. To demonstrate the applicability of NMR relaxometry in this field, MDMO‐PPV/PCBM blends where used, since these are known for their significant phase separation behavior in combination with toluene as solvent. In films prepared from blends in toluene with a PCBM content ≥70 wt %, a fraction of the PCBM is phase separated into crystalline domains, whereas the remaining part remains homogeneously mixed with the MDMO‐PPV. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 138–145, 2008     

Rheological and thermal study of delayed crystallization in poly(butylene terephthalate)/ethylene‐co‐ethyl acrylate blends

The effects of the composition and resulting morphology on the crystallization and rheology of blends containing poly(butylene terephthalate) (PBT) and an ethylene‐co‐ethyl acrylate (EEA) copolymer, two immiscible polymers, were studied over the entire range of volume fractions. Differential scanning calorimetry (DSC) thermograms recorded during cooling showed important differences, mainly in terms of the PBT crystallization temperatures, depending on the blend composition. In addition to the classical crystallization peaks of PBT and EEA, a third crystallization peak appeared for blends containing less than 60% PBT. This peak was attributed to a delayed crystallization of PBT. This phenomenon was examined in terms of homogeneous crystallization. Linear viscoelastic measurements allowed the delayed crystallization behavior in these polymer blends to be displayed. Indeed, the variation of the storage modulus with the temperature showed increasing steps during cooling. These sudden increases appeared at temperatures very close to those at which the crystallization peaks were observed in the DSC experiments. This behavior was verified for different blend compositions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 714–721, 2004     

Interlocking layer structures formed in spin‐cast polymer blend films by surface segregation and self‐stratification

Surface morphologies formed by the phase segregation of poly(styrene‐b‐ethylene/butylene‐b‐styrene) (SEBS)/poly(methyl methacrylate) (PMMA) blend films prepared via spin coating on mica substrates were studied with atomic force microscopy accompanied by a solvent extraction treatment, X‐ray photoelectron spectroscopy, and contact‐angle measurements. Three kinds of surface structures of films were observed. Besides the ribbonlike morphology and the dispersed domains in a continuous matrix that are common in this field, we found a special interlocking layer structure characterized by a smooth SEBS layer as the cover on the top and a layer composed of hill‐like PMMA dispersed in the SEBS matrix at the bottom when the composition of the film was around 50:50 SEBS and PMMA. A series of blend films with different thicknesses were then prepared to investigate the interfacial structure, and the formation process of the interlocking layer, which could be elucidated by a schematic diagram, was discussed. The interlocking bilayer film with SEBS on the top possessed high thermal stability and the best surface roughness in comparison with other structures. It might find important technical applications in fields such as adhesion, lubrication, and protective coatings. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 532–543, 2007.     

Periodic organic–organometallic microdomain structures in poly(styrene‐block‐ferrocenyldimethylsilane) copolymers and blends with corresponding homopolymers

A series of poly(styrene‐block‐ferrocenyldimethylsilane) copolymers (SF) with different relative molar masses of the blocks were prepared by sequential anionic polymerization. The bulk morphology of these polymers, studied by TEM and SAXS, showed well‐ordered lamellar and cylindrical domains as well as disordered micellar structures. Temperature‐dependent rheological measurements exhibited an order–disorder transition for SF 17/8 (the numbers refer to the relative molar masses in 10³ g/mol) between 170 and 180°C, and an order–order transition for SF 9/19 between 190 and 200°C. The morphologies of binary blends of the diblocks with homopolymer were also investigated. In the blends the molar mass of the homopolymer was always less than the molar mass of the matching block. Ordered spheres on a bcc lattice and double‐gyroid morphology were observed for the blends. The double‐gyroid morphology was found only in F‐rich diblock/homopolymer systems. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1009–1021, 1999     

4,9‐Dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione functionalized copolymers for organic photovoltaic devices

The synthesis of conjugated polymers 1 – 5 functionalized with 4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione in the backbone is reported and their use in the construction of organic solar cells is demonstrated. Increasing the molar ratio of 2,7‐dibromo‐3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione, relative to 4,4′‐dihexyl‐5,5′‐dibromo‐2,2′‐bithiophene, in the copolymer synthesis significantly lowers the solubility of these polymers. The incorporation of highly conjugated 3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione unit into the polymer backbone has been confirmed by UV–vis absorption. The observation of decreasing quantum yield for the emission in the order of 1 , 2 , 3 is consistent with copolymers with different comonomer content. The power conversion efficiencies of solar cells using blends of these polymers with PCBM ([6,6]‐phenyl C₆₁‐butyric acid methyl ester) were determined to be 0.11% for polymer 1 , 0.33% for 2 , and 0.26% for 3 , respectively. Under identical white light illumination, the power conversion efficiency of the device based on polymer 2 /PCBM as the active layer was three times higher compared to that of device based on polymer 1 /PCBM. Owing to the limited solubility and poor film‐forming ability of polymer 3 , the power conversion efficiency of solar cell based on 3 /PCBM blend is lower than that of 2 /PCBM blend, but is still larger than that of 1 /PCBM blend. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2680–2688, 2008     

Complex phase behavior and state of miscibility in Poly(ethylene glycol)/Poly(l‐lactide‐co‐ε‐caprolactone) Blends

A miscibility and phase behavior study was conducted on poly(ethylene glycol) (PEG)/poly(l ‐lactide‐ε‐caprolactone) (PLA‐co‐CL) blends. A single glass transition evolution was determined by differential scanning calorimetry initially suggesting a miscible system; however, the unusual T_g bias and subsequent morphological study conducted by polarized light optical microscopy (PLOM) and atomic force microscopy (AFM) evidenced a phase separated system for the whole range of blend compositions. PEG spherulites were found in all blends except for the PEG/PLA‐co‐CL 20/80 composition, with no interference of the comonomer in the melting point of PEG (T_m = 64 °C) and only a small one in crystallinity fraction (X_c = 80% vs. 70%). However, a clear continuous decrease in PEG spherulites growth rate (G) with increasing PLA‐co‐CL content was determined in the blends isothermally crystallized at 37 °C, G being 37 µm/min for the neat PEG and 12 µm/min for the 20 wt % PLA‐co‐CL blend. The kinetics interference in crystal growth rate of PEG suggests a diluting effect of the PLA‐co‐CL in the blends; further, PLOM and AFM provided unequivocal evidence of the interfering effect of PLA‐co‐CL on PEG crystal morphology, demonstrating imperfect crystallization in blends with interfibrillar location of the diluting amorphous component. Significantly, AFM images provided also evidence of amorphous phase separation between PEG and PLA‐co‐CL. A true T_g vs. composition diagram is proposed on the basis of the AFM analysis for phase separated PEG/PLA‐co‐CL blends revealing the existence of a second PLA‐co‐CL rich phase. According to the partial miscibility established by AFM analysis, PEG and PLA‐co‐CL rich phases, depending on blend composition, contain respectively an amount of the minority component leading to a system presenting, for every composition, two T_g's that are different of those of pure components. © 2013 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2014 , 52, 111–121     

Effect of preparation method on nanoscopic structure of conductive SBS/PANI blends: Study using small‐angle X‐ray scattering

Small‐angle X‐ray scattering (SAXS) studies of electrically conductive blends based on polyaniline–dodecylbenzenesulfonic acid (PANI–DBSA)/styrene–butadiene–styrene (SBS) triblock copolymer were performed to investigate the influence of the blend preparation procedure on the nanoscopic structure of the blends. The blends were prepared by mechanical mixing (MM) procedure and by in situ polymerization (ISP) of aniline in the presence of SBS. The results indicate that pure PANI–DBSA presents an extended phase consisting of crystalline islands of nanometric size, with a good spatial correlation between them, embedded into an amorphous PANI phase. This feature was not observed in SBS/PANI–DBSA blends prepared by MM or ISP. In MM blends, the PANI phase is constituted by smaller domains, containing poorly spatially correlated crystalline islands, whereas in ISP blends with low or medium amount of PANI, there is no SAXS peak which could be related to a spatial correlation between PANI crystalline islands. The conductivity of the ISP blends is higher when compared to MM blends because of the higher homogeneity at nanometric scale. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3069–3077, 2007     

Effect of side chain length on the morphology of blends of 2,5‐bis(3‐alkylthiophen‐2‐yl)thieno[3,2‐b]thiophene oligomers and fullerene derivatives

Using molecular dynamics simulations we study blends of oligomers of 2,5‐bis(3‐alkylthiophen‐2‐yl)thieno[3,2‐b]thiophene, BTTT, and fullerene derivative based acceptors to understand the role of oligomer length and alkyl side chain (SC) length on the morphology of their blends. We use a validated coarse‐grained model of BTTT and fullerene derivatives presented in recent work along with direct comparison of morphology between simulations and experiments. In this article, we predict computationally that short alkyl SCs (6 alkyl groups) decrease the propensity of fullerene derivative acceptors to intercalate between SCs on the BTTT backbone compared to longer alkyl SCs (9 or 12 alkyl groups), and as a result increase acceptor aggregation. The decreasing acceptor intercalation and increasing acceptor aggregation do not significantly impact the positional or orientational order of the BTTT backbones. However, the BTTT oligomer backbones order better with increasing SC length in both neat systems and in blends, with the blends exhibiting higher positional order than neat systems. While these qualitative trends are similar both in 2mer blends and 4mer blends, we see a larger extent of acceptor intercalation and as a result, smaller acceptor cluster sizes in the 4mer blends. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 89–97