Determination of trace amounts of nickel by differential pulse adsorptive cathodic stripping voltammetry using calconcarboxylic acid as a chelating agent

A method for the determination of nickel(II) by stripping voltammetry is described. The method is based on the adsorptive accumulation of nickel(II) calconcarboxylic acid complex onto a hanging mercury drop electrode (HMDE), followed by the reduction of the adsorbed complex using differential pulse voltammetry. The optimum operating conditions and parameters were found to be 0.05 M NH₃/NH₄Cl buffer (pH = 9.5) as the supporting electrolyte, a ligand concentration of 1 × 10^?6 M, accumulation potential of ?0.5 V (vs. Ag/AgCl) and accumulation time of 60 s. At the optimized conditions, the peak current is proportional to the concentration of nickel in the range of 1.7 × 10^?9 to 4.7 × 10^?7 M (0.1–28 ng ml^?1) with a detection limit of 0.05 ng ml^?1. The relative standard deviation (n = 10) at nickel concentrations of 2, 10 and 15 ng ml^?1 varies in the range 0.76 to 2.1%. Possible interferences by metal ions, which are of great significance in real matrices, have been studied. The method was successfully applied to the determination of nickel content in a chocolate sample.     

Sensitive Anodic Stripping Voltammetric Copper Ions Determination Performed in Double Deposition and Double Stripping Steps System for Real Water Samples Analysis

The article reports on utilization of double deposition and stripping steps for increasing sensitivity of Cu(II) determination by anodic stripping voltammetry (ASV) at two lead film working electrodes. A significant preconcentration of copper was achieved thanks to utilization of a simple design of four electrodes system that gives possibility to perform one measurement cycle consisting of two deposition and two stripping steps. Due to the fact that deposition step is doubled, the concentration of Pb(II) needed to lead film electrodes formation was significantly reduced as compared to traditional procedures using three electrodes system. The analytical procedure of Cu(II) determination was optimized. The experimental factors: supporting electrolyte's pH and its concentration, lead ions concentration, potential and time of deposition at both working electrodes were studied. The Cu(II) peak current was linearly dependent on its concentration from 5×10^?10 to 2×10^?8 mol L^?1 (deposition time of 270 and 160 s at the first and the second working electrode, respectively). The obtained detection limit for copper ions determination was 2.1×10^?10 mol L^?1. The described procedure was validated by analysis of two water certified reference materials. The described procedure was also utilized for real water sample analysis.     

Analytical Determination of N-(2-Mercapto Propionyl)Glycine (Tiopronin) by Voltammetric Methods

Abstract

The anodic processes which occur at the mercury electrode in N-(2-mercaptopropinyl)glycine (tiopronin) solutions are studied by polarographic techniques (d.c., d.p. and a.c₁.), controlled potential coulometry and cathodic stripping voltammetry. According to the observed electrochemical behaviour the overall electrode process is the formation of a mercury(II)-mercaptide. Adsorption on the electrode of both the mercaptide and the free thiol is present. The d.p.p. peak at -0.58 V or the voltammetric stripping peak at -0.56 V are used for the analytical determination of N-(2-mercaptopropionyl)glycine within the concentration ranges 7.0 10^?5 - 6.8 10^?6 mol 1^?1 or 3.0 10^?7 - 1.0 10^?9 mol I^?1, respectively. Calibration functions are reported in both cases. The interference of several organic compounds is described.     

Catalytic adsorptive stripping voltammetric determination of copper(II) on a carbon paste electrode

A catalytic adsorptive stripping voltammetric method for the determination of copper(II) on a carbon paste electrode (PCE) in an alizarin red S (ARS)-K₂S₂O₈ system is proposed. In this method, copper(II) is effectively enriched by both the formation and adsorption of a copper(II)-ARS complex on the PCE, and is determined by catalytic stripping voltammetry. The catalytic enhancement of the cathodic stripping current of the Cu(II) in the complex results from a redox cycle consisting of electrochemical reduction of Cu(II) ion in the complex and subsequent chemical oxidation of the Cu(II) reduction product by persulfate, which reduces the contamination of the working electrode from Cu deposition and also improves analytical sensitivity. In Britton-Robinson buffer (pH 4.56±0.1) containing 3.6×10⁻⁵ mol L⁻¹ ARS and 1.6×10⁻³ mol L⁻¹ K₂S₂O₈, with 180 s of accumulation at −0.2 V, the second-order derivative peak current of the catalytic stripping wave was proportional to the copper(II) concentration in the range of 8.0×10⁻¹⁰ to ∼3.0×10⁻⁸ mol L⁻¹. The detection limit was 1.6×10⁻¹⁰ mol L⁻¹. The proposed method was evaluated by analyzing copper in water and soil.     

Bismuth Film Microelectrode Modified with Overoxidized Poly‐1‐Naphtylamine Protective Membrane for Enhanced Stripping Voltammetric Detection

The application of protective overoxidized poly‐1‐naphtylamine membrane (ONAP) is demonstrated in combination with bismuth film microelectrode (ONAP‐BiFME) for anodic stripping voltammetric measurement of trace heavy metals in the presence of some selected surfactants. The ONAP membrane was electrochemically deposited on the surface of bare single carbon fiber microelectrode followed by the in situ or ex situ preparation of the bismuth film. The key operational parameters influencing the stripping performance of the ONAP‐BiFME were optimized and its electroanalytical performance was examined in the model solution containing Cd(II) and Pb(II) as test metal ions. The ONAP‐BiFME exhibited significantly enhanced stripping voltammetric response (approximately 70% for Cd(II) and 45% for Pb(II)) in comparison with unmodified BiFME in the absence of surfactants. In the presence of high concentrations, e.g., 20 mg L^?1, of anionic or cationic surfactants, the stripping signal for, e.g., Cd(II) decreased for less than 6% at the ONAP‐BiFME, whereas at the unmodified BiFME the signal attenuated considerably (approximately 38%). Moreover, in the presence of 10 mg L^?1 of nonionic surfactant Triton X‐100, the stripping signals at the bare BiFME were almost completely suppressed, whereas at the ONAP‐BiFME exhibited linear concentration behavior in the examined concentration range from 10 to 120 μg L^?1, with the calculated limit of detection of 5.0 μg L^?1 and 3.4 μg L^?1 for Cd(II) and Pb(II), respectively in connection with 60 s accumulation time. The attractive behavior of ONAP‐modified BiFME expands the applicability of bismuth‐based electrodes for measurement of trace heavy metals in real environments, where the presence of more complex matrix can be expected.     

Stripping voltammetric determination of azide ions

A procedure is proposed for the stripping voltammetric determination of N ₃ ^? ions at a mercury film electrode. It is based on the reduction of the mercury azide formed upon the oxidation of mercury in the presence of N ₃ ^? at ?0.02 to ?0.04V (in reference to an Ag/AgCl electrode) in a 0.1 M Na₂SO₄ supporting electrolyte solution. A linear dependence of the cathodic current peak on the N ₃ ^? concentration is observed in the concentration range from 4 × 10^?9 to 1 × 10^?3 M.     

Cathodic stripping voltammetry and adsorptive stripping voltammetry of selenium(IV)

Cathodic stripping voltammetry of selenium(IV) in 0.1 M hydrochloric acid media yielded a nonlinear calibration graph for the concentration range 10^?9?10^?8 M. In this concentration range, adsorptive stripping voltammetry based on adsorption of the selenium/3,3′-diaminobenzidine complex on the surface of the hanging mercury drop electrode at the deposition potential of +0.05 V (vs. SCE) is more convenient. A linear calibration graph is obtained for selenium concentrations of 3×10^?9?3×10?8 M, with an accumulation time of 300 s.     

Electrochemical Behavior of 6-Mercapto-Purine at Hanging Copper Amalgam Dropping Electrode and Its Trace Determination by Differential Pulse Adsorption Cathodic Stripping Voltammetry

Abstract

The electrochemical behavior of 6-MP was studied by cyclic voltammetry at a hanging copper amalgam dropping electrode (HCADE). It was found that 6-MP could form a complex with the Cu(II) stripped from the HCADE, showing a new peak at ?0.19V in the medium of 0.1mol/L LiClO₄-0.5mol/L HClO₄ solution. The mechanism of the reaction was proposed. This new peak was sensitive and could be used for the determination of trace 6-MP by differential pulse adsorption cathodic stripping voltammetry (DPAdCSV). The linear range was from 3.6×10^?10 to 5.3×10^?6 mol/L, and the detection limit was about 1.2×10^?10 mol/L (S/N=3). The method was also successfully applied to the determination of 6-MP in pharmaceutical tablets.     

Cathodic Stripping Voltammetry of 2-Mercapto-5-Methyl-1,3,4-Thiadiazol and 2,5-Dimercapto-1,3,4-Thiadiazol at a Controlled-Growth Mercury Drop Electrode

2-Mercapto-5-methyl-1,3,4-thiadiazol (MMTD) and 2,5-dimercapto-1,3,4-thiadiazol (DMTD) were studied by differential pulse cathodic stripping voltammetry (DPCSV). The influence of buffer, pH, accumulation potential (E_acc), and accumulation time (t_acc) was investigated. It was stated that the concentration of the buffer affects the height of DPCSV peaks. The best analytical signals were recorded in acetate buffer at pH 4.3 and a buffer concentration of 0.01 mol/L for MMTD and 0.02 mol/L for DMTD, E_acc = 0.2 V, and t_acc = 120 s for MMTD and 180 s for DMTD. A linear dependence was found from 1 to 8 × 10^?8 mol/L for MMTD and from 1 × 10^?8 to 1 × 10^?7 mol/L for DMTD. The influence of cations [Cu(II), Co(II)] was also considered.     

Determination of Cd(II) in Some Foodstuffs by Anodic Stripping Pulse Voltammetry (ASPV) using Glassy Carbon Electrode

Abstract

Cadmium in the presence of 0.04 M NaCl as the electrolyte was determined using stripping voltammetry with superimposed constant amplitude pulses of negative polarity (SVPNP) or positive polarity (SVPPP), and differential pulses stripping voltammetry using rotating disc glass carbon electrode (RDGCE). The SVPNP was found to give the greatest sensitivity. The anodic peak was obtained at potential ?850 to ?795 mV due to the oxidation of cadmium to cadmium(II). Linear calibration curves were obtained in the concentration range between 1.5×10^?9–2×10^?10 M. The relative standard deviation is 4.25% at very low concentration of 2×10^?10 M. This method was successfully applied to the determination of cadmium in some foodstuffs (wheat and its products, vegetables) after acid digestion.     

Determination of lead(II) in aqueous solution using carbon nanotubes paste electrodes modified with Amberlite IR-120

A new composite electrode is described for anodic stripping voltammetry determination of Pb(II) at trace level in aqueous solution. The electrode is based on the use of multiwalled carbon nanotubes and Amberlite IR-120. The anodic stripping voltammograms depend, to a large extent, on the composition of the modified electrode and the preconcentration conditions. Under optimum conditions, the anodic peak current at around ?0.57 V is linearly related to the concentration of Pb(II) in the range from 9.6?×?10^?8 to 1.7?×?10^?6 mol L^?1 (R?=?0.998). The detection limit is 2.1?×?10^?8 mol L^?1, and the relative standard deviation (RSD) at 0.24?×?10^?6 mol L^?1 is 1.7% (n?=?6). The modified electrode was applied to the determination of Pb(II) using the standard addition method; the results showed average relative recoveries of 95% for the samples analysed.

Determination of mercury ions on a diphenylcarbazone bulk modified graphite electrode

A bulk modified electrode prepared by pressing a mixture of carbon powder and diphenylcarbazone at 15.2 MPa was used for the determination of mercury in aqueous solutions. Mercury(II) ions are concentrated by complexation with the modifier in acidic (HNO₃) solution. After exchange of the medium for 1 M HCl and 1 M CaCl₂, mercury is reduced at ?0.8 V vs. SCE. The signal is generated by anodic stripping in the differential-pulse mode. The calibration graph is linear in the range 5×10^?8?5× 10^?6 M with a relative standard deviation of 7%. After enrichment for 10 min the detection limit is 5×10^?8 M. Silver, chromate and strong complexing agents interfere. The use of the electrode to determine the labile fraction in mercury speciation is discussed.     

Renewable Ceramic (TiN) Ring Electrode in Stripping Voltammetry. Determination of Pb(II) Without Removal of Oxygen

Characteristic features of the process of Pb(II) reduction and oxidation at a renewable ceramic ring electrode (RCRE) were studied by stripping voltammetry. The main constituents of the RCRE are: a specially constructed TiN ring electrode, a silver sheet used as silver counter/quasi‐reference electrode and a silicon O‐ring are fastened together in a polypropylene body. The renovation of this electrode is carried out through mechanical removal of solid contaminants and electrochemical activation in the electrolyte which fills the RCRE body. The optimal measurement conditions, composition of supporting electrolyte and procedures of the electrode activation were selected. The measurements were carried out from nondeaerated solutions. As shown on selected examples, RCRE exhibits good performance in underpotential deposition stripping voltammetry (UPD‐SV) applied for the determination of lead(II) in synthetic solutions with and without surfactants and in certified reference materials. The peak current is proportional to the concentration of lead(II) over the range 2×10^?9–1×10^?7 mol L^?1, with a 3σ detection limit of 1×10^?9 mol L^?1 with an accumulation time of 30 s. The obtained results showed good reproducibility, (RSD=2–5%; n=5) and reliability.     

Electrochemical detection of blood lead based on the enhancement effect of copper

The anodic stripping peak current of lead on the glassy carbon electrode surface was greatly increased in the presence of high concentration of copper ion. The effects of supporting electrolyte, concentration of Cu²⁺, accumulation potential and accumulation time were studied on the stripping peak current of Pb²⁺. As a result, a sensitive, simple and rapid electrochemical method was developed for the detection of lead. In 0.01 M HNO₃ solution containing 800 g,g L^?1 Cu²⁺, the stripping peak current of Pb²⁺ increases linearly with its concentration over the range from 2 to 100 μg L^?1. The detection limit is 1 μg L^?1 after 4-min accumulation at ?0.8 V. It was used to detect the concentration of lead in blood samples, and the results consisted with the values that obtained by atomic absorption spectrometry.     

Ex Situ Prepared Antimony Film Electrode for Electrochemical Stripping Measurement of Heavy Metal Ions

The antimony film electrode (SbFE) was prepared ex situ for anodic and adsorptive stripping voltammetric measurement of selected heavy metal ions. The electrode revealed good linearity for Cd(II) and Pb(II) in a nondeaerated solution of 0.01 M HCl in the examined concentration range from 25 to 80 μg L^?1 with limits of detection of 1.1 μg L^?1 for Cd(II) and 0.3 μg L^?1 for Pb(II) and an excellent reproducibility. The preplated SbFE was also preliminary tested for measuring low levels of Ni(II) using adsorptive stripping voltammetry exhibiting good linearity and sensitivity in combination with only a 30 s deposition step.     

Determining Trace Concentrations of Copper in Water by Cathodic Film Stripping Voltammetry with Adsorptive Collection

Abstract

A technique is presented for the determination of trace concentrations of copper (II) in natural water samples by cathodic stripping voltammetry of a film of copper-catechol complex ions adsorbed on the hanging mercury drop electrode. The peak height of the copper-catechol reduction peak is linearly dependent upon the copper (II) concentration between 10^?10 and 10^?7 M. The detection limit of the technique is below 10^?10 M copper (II) for a collection time of 3 minutes, but the sensitivity can be further increased four-fold by collecting for 15 minutes. The sensitivity is reduced by high concentrations of competing trace metals and of surfactants, which necessitate the use of standard additions to the sample.     

Stripping Potentiometry of Lead,Cadmium and Copper at a Nafion Coated Glassy Carbon Electrode with Encapsulated Mercury Acetate

Abstract

The stripping potentiometric determination of lead, cadmium and copper with mercury film glassy-carbon electrodes coated with a Nafion membrane was investigated. The mercury film was plated using either mercury(II) acetate encapsulated within the Nafion membrane or a mercury(II) solution. Dissolved dioxygen was used as the stripping agent. The electrodes showed promising properties, particularly robustness and response repeatability. A linear dependence of the stripping time on concentration was found in the μg l^?1 concentration range (s.d. of intercept ≤ 0.3 μg l^?1, r.s.d. of slope ≤ 1%, for both lead and cadmium).     

Differential-pulse anodic stripping voltammetry of mercury with gold-film micro-electrodes

Cylindrical gold film micro-electrodes are easily produced by plasma-sputtering of gold onto carbon fiber electrodes. The micro-electrodes produced were found to maintain their cylindrical geometry indefinitely, unlike gold wire electrodes of similar dimensions. Application of these electrodes in differential-pulse anodic stripping voltammetry provides a method for quantifying trace levels of mercury(II). Up to 100 μg l^?1 Hg(II) the area of the mercury stripping peak varied linearly with mercury concentration; the detection limit was 3.7 μg l^?1. With more than 100 μg l^?1 Hg(II) a new mercury stripping peak grows in at less positive potentials; its peak height is linear with Hg(II) concentration.     

Voltammetric Behavior of Mifepristone (RU‐486) Using Square‐Wave and Adsortive Stripping‐Wave Techniques. Determination in Urine Samples

The behavior of Mifepristone (RU‐486) was studied by square‐wave technique, leading to two methods for its determination in aqueous samples and urine samples at pH 2. The application of the square‐wave (SW) without the adsorptive accumulation and stripping voltammetric (AdSV) show the maximum response at ?0.896 V using an accumulation potential of ?0.5 V. The effect of experimental parameters that affect this determination are discussed. For the stripping technique, Mifepristone proved to be more sensitive, yielding signals four times larger than those obtained by applying a square‐wave scan without the previous accumulation. The calibration plot to determine Mifepristone was linear in the range 2.4×10^?8 and 5.4×10^?7 M by stripping mode with an accumulation time t_acc of 30 s. The relative standard deviation obtained for concentration levels of Mifepristone as low as 2.0×10^?7 M with square‐wave was 1.17% (n=10) and with stripping square‐wave 2.02% (n=10) in the same day. The two proposed methods (SW and SWAdSV) were applied to the determination of Mifepristone in urine.     

The Determination of Nonelectroactive Anticancer Drug 6‐Thioguanine on DNA‐Modified Gold Electrode

Abstract

A nonelectroactive anticancer drug 6‐thioguanine was determined by differential pulse stripping voltammetry on the DNA‐modified gold electrode. The electrode was prepared by the dry adsorptive method, which is simple and direct. Potassium ferricyanate [K₃Fe(CN)₆] was chosen as an appropriate electroactive indicator to probe and characterize the interaction since the 6‐thioguanine and DNA both are nonelectroactive over the potential range studied. The reductive peak current of K₃Fe(CN)₆ is linear with the concentration of 6‐thioguanine in the range of 2.0×10^?8～8.0×10^?7 mol L^?1. The detection limit is 6.0×10^?9 mol L^?1. The established method was successfully applied to determining trace 6‐thioguanine with the recoveries between 95.7% and 105.6%.