Determination of beryllium in copper-beryllium alloys by flow-injection spectrophotometry

Summary A method is described for the flow-injection spectrophotometric determination of beryllium in Cu-Be-alloys using xylenol orange as reagent. Cu, Co and Fe are masked by means of thiosulphate and EDTA. Absorbance is measured at the maximum of 493 nm. With a flow rate of 4 ml/min 60 samples can be analyzed per hour with a relative standard deviation of about 1%.

---

Bestimmung von Beryllium in Cu-Be-Legierungen durch Flow-Injection-Spektralphotometrie

Zusammenfassung Als Reagens zur spektralphotometrischen Bestimmung von Berryllium in Cu-Be-Legierungen dient Xylenolorange. Cu, Co und Fe werden mit Hilfe von Thiosulfat und EDTA maskiert. Die Messung erfolgt im Absorptionsmaximum des Komplexes von 493 nm. Bei einer Durchflußgeschwindigkeit von 4 ml/min können 60 Proben je Stunde mit einer relativen Standardabweichung von etwa 1% analysiert werden.

     

Determination of residual chlorine in tap water by flow-injection spectrophotometry

The method is based on the redox reaction between 4,4′-tetramethyldiaminothiobenzophenone (thio-Michler's ketone) and chlorine at pH 3.5; 2-methoxyethanol and Triton X-100 are used to keep the reagent in solution. The absorbance of the blue quinoidal product is measured at 640 nm. Linear calibration is obtained for 0.2?1.0 mg l^?1 chlorine. The method is suitable for tap waters.     

Determination of sucrose in sugar-cane juice and molasses by flow-injection spectrophotometry

An automated procedure is proposed for the spectrophotometric determination of sucrose in sugar-cane juice and nonlasses. The previously diluted and filtered sample is introduced into a flow-injection analyzer designed with two merging streams, producing two samples zones. One zone is transported directly towards the merging-stream confluence; the other zone reaches this site after flowing through a heated coil in which partial and reproducible sucrose inversion is attained under controlled conditions of acidity and temperature. At the confluence point, a buffered periodate stream is added to oxidize the sugar. The consumption of periodate, which mainly reflects the fructose content, is measured spectrophotometrically as a transient lowering of the iodine concentration, produced by reaction of periodate with iodide. The two processed zones proceed sequentially to the flow cell and two peaks are recorded. The sucrose content in the sample is proportional to the difference in peak heights. System dimensioning and the effects of temperature, pH, reagent concentrations, flow rates and the presence of other reducing sugars in the sample are discussed. With the proposed system, about 30 sugar-cane juice samples can be analyzed per hour, and sample clarification is not required. Precise results (r.s.d. <1%), in agreement with those obtained by h.p.l.c., are achieved for sucrose contents of 11–14% (w/v) in cane juice. Modifications of the system for analysis of molasses (16–52% w/w sucrose) are described.     

Determination of formaldehyde in Brazilian alcohol fuels by flow-injection solid phase spectrophotometry

In this work, a solid phase spectrophotometric method in association with flow injection analysis for formaldehyde determination has been developed with direct measurement of light-absorption in C₁₈ material. The 3,5-diacetyl-1,4-dihydrolutidine produced from the reaction between formaldehyde and fluoral P was quantitatively retained on C₁₈ support and the spectrophotometric detection was performed simultaneously at 412 nm. The retained complex was quickly eluted from C₁₈ material with the eluent stream consisting of a 50% (v/v) ethanol solution. The results showed that the proposed method is simple, rapid and the analytical response is linear in the concentration range of 0.050-1.5 mg L⁻¹. The limit of detection was estimated as 30 μg L⁻¹ and the R.S.D. 2.2% using a sample volume of 625 μL. The system presented an analytical throughput of 20 determinations per hour. The method was successfully applied in the determination of formaldehyde in ethanol fuel.     

Determination of phosphorus in biological tissues by aluminium block digestion and flow-injection spectrophotometry

Biological tissues are digested with nitric and perchloric acids in a heated aluminium block. Flow-injection spectrophotometry is then used to measure phosphate via the phosphovanadomolybdate complex at 413 nm. The detection limit is 0.3 μg ml^?1 phosphorus; relative standard deviations are 0.7% and 0.4% at 1 μg ml^?1 and 25 μg ml^?1 phosphorus, respectively. Interferences are discussed. The decomposition procedure is evaluated for model compounds and standard reference materials.     

A sensitive determination of paraquat by spectrophotometry

A sensitive spectrophotometric method for the determination of a widely used herbicide, paraquat using a versatile reducing agent sodium borohydride is described. Paraquat is reduced with sodium borohydride in an alkaline medium to give a blue radical ion with an absorbance maxima at 600 nm. Beer's law is obeyed in the range of 0.05-0.5 mug ml(-1) of paraquat. The molar absorptivity and Sandell's sensitivity are found to be 2.9 x 10(5) l mol(-1) cm(-1) and 0.0006 mug cm(-2) respectively. The important analytical parameters and the optimum reaction conditions were evaluated. The method is free from the interference of other commonly used pesticides and metal ions. The method was applied successfully to the determination of paraquat in human samples, such as blood, urine and mother's milk compared to food and environmental samples.     

Determination of ambroxol hydrochloride in tablets using flow-injection UV spectrophotometry and HPLC

A flow-injection UV spectrophotometric method was developed for the determination of ambroxol hydrochloride in tablets. The quantitative determination of ambroxol was performed at 245 nm using distilled water as the carrier solvent. In this study, the flow rate, loop volume, and the number of injections per hour were 15 mL/min, 193 μL, and 100, respectively. The analytical signal of ambroxol was linear in the concentration range of 40–200 μg/mL. The detection limit and limit of quantification were found as 11.55 and 38.49 μg/mL, respectively. The results for the determination of ambroxol in tablets, 29.99 ± 0.23 mg (mean ± SD), were in good agreement with the labeled quantities (30 mg/tablet). A relatively high recovery value (100.4%) shows the accuracy of the proposed method. Furthermore, the results obtained were in accordance with those obtained by the HPLC method, which were used as a comparison method for the determination of ambroxol HCl, as far as the Student’s t-test and Fisher test results were concerned. It was concluded that the proposed flow-injection UV spectrophotometric method was fast, accurate, precise, and suitable for automation in the determination of ambroxol. The text was submitted by the authors in English.     

Simultaneous determination of formaldehyde and methanol by flow-injection catalytic spectrophotometry

A flow-injection method is proposed for the simultaneous catalytic determination of formaldehyde and methanol on the basis of the catalytic action of formaldehyde upon the redox reaction between crystal violet and potassium bromate in a phosphoric acid medium and on-line oxidization of methanol into formaldehyde using a lead dioxide solid-phase reactor. The indicator reaction is monitored spectrophotometrically by measuring the decrease in the absorbance of crystal violet at the maximum absorption wavelength of 610 nm. A technique based on three sampling loops with a single injection valve is developed. The flow-injection system produces a signal of main peak with two shoulders of the same height. The height of the shoulders corresponds to the formaldehyde concentration, and the height difference between the shoulders and the main peak corresponds to the methanol concentration. The detection limit is 0.1 μg/mL for formaldehyde and 1.0 μg/mL for methanol with the sampling rate of 10 samples per hour. The relative standard deviations for 11 replicate determinations of formaldehyde (1.0 μg/mL) and methanol (10 μg/mL) are 1.1 and 2.1%, respectively. The method has been successfully applied to the simultaneous determination of formaldehyde and methanol in some gas samples. The text was submitted by the authors in English.     

流动注射催化动力学光度法测定碘离子

Based on catalysis of I- on the decolor reaction between potassium bromate and indigo carmine in the acid medium,and combined with flow injection analysis,a new flow-injection catalytic kinetic spectrophotometric method was found for determination of iodide in sample.The experimental results show that the determination is carried out at temperature of 80℃ and the concentration of H_2SO_4,KBrO_3,and indigo carmine is 1.2 mol/L,1.8×10~(-2) mol/L and 1.0×10~(-4) mol/L respectively,the linear range for the method is 0.50～1.8 mg/L.The detection limit is 0.0022 mg/L.The relative standard deviation is 1.92%.The proposed method was applied to the determination of iodide in troche successfully.The recovery was between 99.2% and 103.6%.     

Determination of naphthols by flow-injection chemiluminescence

1-Naphthol, 2-naphthol, 2-naphthol-6-sulphonic acid, 1-amino-2-naphthol-4-sulphonic acid and 1-amino-2-naphthol hydrochloride are determined by the chemiluminescence produced by acidic permanganate oxidation in a flow system. Rhodamine B is used as sensitizer. The limits of detection are ca. 5×10^?7 M in a 20-μ sample.     

Rapid continuous determination of aluminium in copper-base alloys by flow-injection spectrophotometry

Summary A flow-injection spectrophotometric method has been developed for the rapid, continuous determination of aluminium in copper-base alloys. The system consists of the masking of copper, zinc, iron, etc. with a combined use of thiourea, ascorbic acid and EDTA and the measurement of light absorption of aluminium-Xylenol Orange complex at 506 nm. With appropriate standardization satisfactory results are obtained in spite of sluggish reaction of aluminium and Xylenol Orange. The system allows the analysis of solutions of copper-base alloys for aluminium to be conducted at a rate of 50 determinations per hour without any carryover. The results obtained for standard brasses and aluminium bronze (Al 1.43–10.2%) agreed well with the certified values. The precision (rsd) ranges are 0.2–0.3%.

---

Kontinuierliches Schnellverfahren zur Bestimmung von Aluminium in Kupferlegierungen mit Hilfe der Flow-Injection-Spektralphotometrie

Zusammenfassung Bei dem empfohlenen Verfahren werden Cu, Zn, Fe und andere Störelemente mit Hilfe von Thioharnstoff, Ascorbinsäure und EDTA maskiert und der Al-Xylenolorange-Komplex bei 506 nm gemessen. Mit Hilfe eines geeigneten Eichverfahrens werden trotz der trägen Reaktion von Al mit Xylenolorange zufriedenstellende Werte erhalten. 50 Bestimmungen können innerhalb von 1 h ohne jedes Verschleppen durchgeführt werden. Bei der Analyse von Messing und Al-Bronze (1,43–10,2% Al) wurde gute Übereinstimmung mit zertifizierten Werten erzielt. Die Standardabweichungen lagen im Bereich von 0,2–0,3%.

     

Determination of N-acetyl-L-cysteine by flow-injection potentiometry

A multi-purpose tubular flow-through sensor was constructed with an AgI-based membrane. The membrane was prepared by pressing silver salts (AgI, Ag₂S) and powdered Teflon. This membrane was incorporated in the tubular flow-through sensor body. A 2-mm diameter hole was drilled through the center of the tubular sensor and the membrane, thus determining the active sensor volume of about 4 μL. The tubular sensor with reference electrode was placed into a complex flow-injection system and used for the flow-through determination of N-acetyl-L-cysteine, (NAC), in perchloric acid medium, pH = l. Linear dependence was established between the recorded signal height and the concentration of NAC in the injected sample. The recorded change in potential for a decade change in concentration, 62 mV {p (NAC)}^–1, in the concentration range from 1 × 10^–4 to 1 × 10^–1 mol L^–1, was based on the formation mechanism of the sparingly soluble deposit between silver and NAC on the surface of the sensitive part of the membrane. Received: 7 July 1997 / Revised: 22 September 1997 / Accepted: 26 September 1997     

流动注射化学发光法测定片剂中阿昔洛韦含量

在碱性介质中,低浓度的阿昔洛韦会增强鲁米诺-H2O2体系的化学发光,据此建立了测定阿昔洛韦的新方法.该法的化学发光增强值ΔICL与阿昔洛韦的浓度在9.00×10-8～3.00×10-6mol/L范围内呈良好的线性关系,相关系数r为0.9957,检出限为7.71×10 -8mol/L.对1.00×10-6 mol/L的阿...     

Catalytic determination of molybdenum in plants by flow-injection spectrophotometry with ion-exchange separation

The catalytic effect of molybdenum n the oxidation of iodide by hydrogen peroxide is utilized. A cation-exchange resin column is incorporated into the system to remove interfering ions; during sample processing, the interfering ions are eluted towards waste. Plant materials are ashed and solutions are injected. The proposed system can handle about 40 samples per hour with molybdenum contents in the 1.0–40.0 μg 1^?1 range. Results are precise (r.s.d. usually <%) and in agreement with those obtained by graphite-furnace atomic absorption spectrometry.     

Compensation of the Schlieren effect in flow-injection analysis by using dual-wavelength spectrophotometry

The Schlieren effect in flow-injection analysis is critically examined. Effects of sample constitution, injection volume, coil lengths, flow-rates, confluent stream addition and temperature are studied and practical implications in flow-injection design with and without the stopped-flow approach are discussed. For Schlieren compensation, a diode-array spectrophotometer is used and non-specific absorbance subtraction is exploited: the incident light passes through the flowing sample, the emergent light is dispersed, the intensities of two selected monochromatic beams are measured simultaneously by separate detectors and real-time subtraction of the wavelength-independent noise is achieved. The sensitivity and measurement precision improve after application of the subtraction algorithm. The potential, limitations and practical applications of the method are discussed.     

流动注射化学发光法测定己内酰胺

使用己内酰胺增强Ce(Ⅳ) SO32-化学发光体系,结合流动注射分析技术进行了己内酰胺的测定。己内酰胺的质量浓度在4.0×10-7～1.0×10-5g/mL范围内与化学发光分析信号呈线性关系,其检出限为1×10-7g/mL。对4.0×10-7g/mL的己内酰胺溶液进行11次连续测定,相对标准偏差为2.1%。方法已应用于层析用聚己内酰胺中的己内酰胺测定。     

分光光度法测定薯蓣皂苷元

采用高氯酸反应使薯蓣皂苷元显色 ,对影响显色反应的主要因素进行了考察 ,于 41 0nm波长处对穿山龙中薯蓣皂苷元的含量进行测定 ,测定结果与高效液相色谱法相近。方法的线性范围为 3.1 2～2 1 .84μg mL ,适用于薯蓣皂苷元提取过程中的常规检测     

Nickel and zinc determination by flow-injection solid-phase spectrophotometry exploiting different sorption rates

Flow-injection solid-phase spectrophotometry is applied for sequential determination of nickel and zinc, exploiting their different sorption rates on 1-(2-thiazolylazo)-2-naphthol (TAN) immobilized on C(18)-bonded silica. The Zn(II) sorption rate on the solid support is constant for flow rates ranging from 0.70 to 2.2 ml min(-1), but for Ni(II) the sorption rate decreases with increasing flow rate. A flow system was designed to perform sequential measurements at two different flow rates (0.85 and 1.9 ml min(-1)). The absorbance was measured at 595 nm, where both TAN-immobilized complexes showed maximum absorption. The coefficients of variation were estimated (n=10) as 1.1 and 1.7% (at 1.9 ml min(-1)) and 1.2 and 2.1% (at 0.85 ml min(-1)) for zinc and nickel, respectively. This strategy was applied to determine zinc and nickel in copper-based alloys and the results agreed with certified values at the 95% confidence level. The sample throughput was estimated as 36 h(-1).     

流动注射在线过滤稀释原子吸收法测定诺氟沙星

提出了流动注射在线过滤稀释原子吸收法测定诺氟沙星的新方法。药物浓度在0．1－0．8mg/mL范围符合比耳定律，回收率为97．9％－102．4％，相对标准偏差为1．7％。方法可用于诺氟沙星胶囊测定。     

Determination of molybdenum in steels by flow-injection spectrophometry

A flow-injection procedure is proposed for the determination of molybdenum in steels based on the thiocyanate method. Effects of iron(III), acidity, reagent concentration and interfering species were investigated by using flow-injection systems with the merging zones approach which reduced drastically the number of standard solutions to be prepared. Full details of system design are given. The procedure can be applied to several types of steel samples of industrial relevance. After dissolution of the steels in aqua regia, molybdenum can be determined in the range 0.10–4.00% (w/w) at a rate of up to 270 samples per hour with relative standard deviations less than 2%. The results agree with those obtained by atomic absorption spectrometry with the standard addition method and by plasma atomic emission spectrometry, and with certified values of standard reference samples.