Aquacyanocobalt(III)-cobyrinate as a key compound in NO2-sensitive polymeric liquid membranes.

The reactions within a recently introduced NO2-sensitive polymeric membrane based on aquacyanocobalt(III)-cobyrinate are described. The detailed reaction mechanism was investigated in three ways: using UV/VIS-spectroscopy, determining the reaction products and investigating the influence of other gases. It could be shown that the membrane's high sensitivity and selectivity derives from the remarkable reaction of NO2 with this cobyrinate derivative, which yields nitric and nitrous acid. This reaction can be transduced with a consecutive protonation of the included chromoionophore into an optical signal, which allows the detection of NO2 in the ppb-range.     

Long-chain tetraalkyltin compounds as neutral carriers for nitrite-selective PVC membrane electrodes

The nitrite-selective PVC membrane electrodes prepared with lipophilic long-chain tetraalkyltin compounds as neutral carrier show selectivity patterns significantly different from those obtained with classical anion-exchangers. The potentiometric selectivity coefficient for nitrite ion with respect to nitrate ion has been improved by about four orders of magnitude. The linear response range of the electrode based on tetralauryltin (TLT) is from 1 × 10^?1M down to 2×10^?5M with a detection limit of 5 × 10^?6M. The Nernstian response of the electrode in the medium of pH≥7 gradually changes to a doubled super-Nernstian response when the solution turns slightly acidic. The change of the response slope has a closely relation with the stepwise complex-formation equilibrium of the carrier with the anion involved, which was experimentally studied by using ultraviolet spectroscopy. An explanation of the anomalous response behavior as well as the curve form of the potential-pH plot is given.     

Selective transport of yttrium(III) in the presence of iron(III) through liquid-membrane impregnating acidic organophosphonate mobile carrier

The extraction and stripping behavior of yttrium(III) and iron(III) with 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (EHPA) was investigated and applied to liquid-membrane transport for their mutual separation. The extractability of yttrium(III) with EHPA was less than that of iron(III) at equilibrium, but the rates of extraction and stripping of iron(III) were slow. The carrier-mediated transport of yttrium(III) in the presence of iron(III) was investigated through a supported liquid membrane (SLM), impregnated with EHPA as a mobile carrier. Yttrium(III) with fast kinetics was selectively transported across an SLM from a dilute-acid solution into a sulfuric-acid stripping solution, while iron(III) with slow kinetics was hardly transported and was retained in the feed solution. Yttrium(III) was separated from iron(III) through the SLM and quantitative recovery was realized.     

New liquid-membrane electrodes for direct determination of atropine in pharmaceutical preparations

Solutions of atropinium 5-nitrobarbiturate in n-octanol and atropinium picrolonate in p-nitrotoluene are used as novel liquid ion-exchangers in electrodes that respond to the atropine cation. The performance characteristics of the two electrodes are almost identical: the response is linear for 10(-5)-10(-2)M atropine with a slope of 56.5 +/- 1 mV/concentration decade. The static response times are 30-90 sec and the potential readings are stable over the pH range 3-8. There is negligible interference from a number of inorganic and organic cations, and some common excipients. In the direct determination of 1-200 mug/ml of atropine, the average recovery with both electrodes is 98% (mean standard deviation 1.7%). Atropine has been determined in some pharmaceutical preparations with an average recovery of 98% (standard deviation 1.9%), the results being in agreement with those obtained by standard methods.     

Asymmetric Schiff base as carrier in PVC membrane electrodes for manganese (II) ions

Manganese(II) complex of (E)-2-(hydroxyl-5-methoxybenzylideneamino) phenol was synthesized and used as a suitable Mn(II) – selective membrane in PVC matrix. The plasticized membrane sensor exhibits a nersian response for Mn(II) ions over a wide concentration range of 6 × 10^?6–2 × 10^?2 M with slope of 29 ± 1 mV per decade. It has a response time of <11 s and can be used for 2 months without any measurable divergence in potential. The response of the proposed sensor is independent of pH between 4 and 9.5. The proposed sensor shows a fairly good discriminating ability towards Mn(II) in comparison with some hard and soft metals. The electrode was used in the determination of Mn(II) in aqueous solutions and as an indicator electrode in potentiometer titration of manganese ions against EDTA.     

Construction and analytical applications of liquid-membrane electrodes for atropine and novatropine

Liquid-membrane electrodes sensitive to atropinium and novatropinium cations are described. The atropinium electrode exhibits rapid and near-Nernstian response in the 10^-2–3 × 10^-5 M range over the pH range 2–8.5; the novatropinium electrode shows near-Nernstian response in the 10^-2–3 × 10^-6 M range at pH 2–10. Other alkaloids interfere. Direct potentiometry and potentiometric titrations are used to determine atropine and novatropine in pharmaceutical preparations with satisfactory results.     

Synthesis of cationic gold(III) complexes using iodine(III)

Abstract

We report the synthesis and characterization of cationic Au(III) complexes supported by nitrogen-based ligands. The syntheses are achieved by reacting Au(I) complexes [Au(N-Me-imidazole)₂]⁺ and [Au(pyridine)(NHC)]⁺ with iodine(III) reagents PhI(OTf)(OAc) and [PhI(pyridine)₂]²⁺ yielding a series of cationic gold(III) complexes. In contrast, reactions of phosphine ligated gold(I) complexes with iodine(III) reagents results in the oxidation of the phosphine ligand.     

Selective separation of yttrium(III) through a liquid membrane system using 2-thenoyltrifluoroacetone as an extractant carrier

2-Thenoyltrifluoroacetone has been offered as a mobile carrier in organic phase for the transport and selective separation of yttrium from aqueous media using a liquid membrane system. Perceivably, the use of n-propylamine (PA) in the source phase enhances the transport of yttrium ions. The extraction and stripping conditions have entirely been evaluated and explained. The suggested method has been utilized for the separation of yttrium(III) from its binary mixtures with strontium(II) and some other cations such as Ni²⁺, Co²⁺, Ag⁺, Fe²⁺, Al³⁺, Cu²⁺, Hg²⁺and Cs⁺ in aqueous solutions of pH 5.4 in the presence of PA, while 1 M nitric acid was acting as a stripping agent in the receiving division. Cyanide ion and 5-sulfosalicylic acid have been used as masking agents to minimize the interferences from different transition metal ions and Al³⁺ in the source phase, respectively. ⁹⁰Y in secular equilibrium with ⁹⁰Sr in the source phase, was transferred to receiving phase and separated completely from its long-lived parent isotope. The activity of the transported ⁹⁰Y was found to decay with a half-life 64.17 ± 0.05 h. The purity of yttrium-90 was comparable or better than the other applied liquid membrane systems for purification of yttrium-90.     

The first use of a Rh(III) complex as a novel ionophore for thiocyanate-selective polymeric membrane electrodes

The feasibility of a newly synthesized Rh(III) complex, Rh[(trpy)(bpy)Cl](PF₆)₂, as a novel ionophore for the preparation of anion-selective polymeric membrane electrodes was tested. The ionophore exhibited anti-Hofmeister behavior with enhanced potentiometric selectivity toward thiocyanate ion compared to other anions. The influence of some experimental parameters such as membrane composition, nature and amount of plasticizer and additive and concentration of internal solution on the potential response of the SCN⁻ sensor were investigated. The electrode exhibits a Nernstian response for SCN⁻ over a wide concentration range (1.0 × 10⁻⁵ to 1.0 × 10⁻¹ M) with a slope −58.7 ± 0.5 mV per decade and a detection limit of 4.0 × 10⁻⁶ M (0.23 ppm). It could be used in a pH range of 3.0-8.0 and has a fast response time of about 15 s. The proposed sensor was used for the determination of thiocyanate ions in real samples such as urine and saliva of smokers and nonsmokers and, as an indicator electrode, in potentiometric titrations of SCN⁻ ion.     

Thiocyanate-selective membrane electrode based on cobalt(III) Schiff base as a charge carrier

A highly selective polyvinylchloride (PVC) membrane electrode based on Schiff base complex i.e. [Cobalt (Salpen) (PBu₃)] ClO4 · H2O (Salpen = bis(salycilaldehyde)propylene diamine) is reported as new carrier for thiocyanate selective electrode by incorporating the membrane ingredients on the surface of graphite electrodes. The proposed electrode possesses a very wide Nernestian linear range to thiocyanate from 1.0 × 10^?6 to 1.0 × 10^?1 M with slope of ?59.05 ± 0.91 mV per decade of thiocyanate concentration, very low detection limit (8.0 × 10^?7 M) and good thiocyanate selectivity over the wide variety of other anions. Fast and stable response, good reproducibility, long-term stability, applicability over a wide pH range (2.8–9.8) are advantages of the reported electrode. The sensor has a response time of <5 s and can be used for at least 14 weeks without any considerable change in respective potential response. The proposed electrode was used for the determination of thiocyanate in saliva, wastewater and human urine with satisfactory results and good agreement with colorimetric as reference method.     

Myoglobin modified electrodes as anchors for d metal cationic complexes

The capability of adsorption of different electroactive cationic Re(V)-amine complexes onto myoglobin-containing electrodes has been investigated. The goal of this work was the development of an Au/thiol/myo electrode and, after incubation of such ensemble in the presence of three different Re(V)-amine complexes, the evaluation of the extent of surface coverage by the complexes (as a way to evaluate the interaction complex-protein) using electrochemical techniques. Our results showed that a protein-containing electrode could therefore be used for the detection of the interaction of small electroactive cationic complexes and the biomolecule. The extent of the coverage of the myoglobin electrode by the complex depends on the number of free tails from the ligands and the total charge of the complex.     

Study of a bis-furaldehyde Schiff base copper(II) complex as carrier for preparation of highly selective thiocyanate electrodes

A new highly selective thiocyanate electrode based on N,N-bis-(furaldehyde)-1,2-phenylenediamine-dipicolyl copper(II) complex [Cu(II)-BFPD] as neutral carrier is described. The electrode has an anti-Hofmeister selectivity sequence: SCN^–>I^–>Sal^–>ClO₄ ^–>Br^–>NO₂ ^–>Cl^–>NO₃ ^–>SO₄ ^2–>SO₃ ^2–>H₂PO₄ ^– and a near-Nernstian potential linear range for thiocyanate from 1.0×10^–1 to 5.0×10^–6 mol L^–1 with a detection limit 2.0×10^–6 mol L^–1 and a slope of 57.5 mV decade^–1 in pH 5.0 of phosphate buffer solution at 20 °C. The response mechanism is discussed on the basis of results from A.C. impedance measurement and UV spectroscopy. The anti-Hofmeister behavior of the electrode results from a direct interaction between the central metal and the analyte ion and a steric effect associated with the structure of the carrier. The electrode has the advantages of simplicity, fast response, fair stability and reproducibility, and low detection limit. The selectivity of electrodes based on [Cu(II)-BFPD] exceeds that of classical anion-sensitive membrane electrodes based on ion exchangers such as lipophilic quaternary ammonium or phosphonium salts. Application of the electrode for determination of thiocyanate in waste water samples from a laboratory and a gas factory, and in human urine samples, is reported. The results obtained were fair agreement with the results obtained by HPLC.     

Facilitated transport of Am(III) through a flat-sheet supported liquid membrane (FSSLM) containing tetra(2-ethyl hexyl) diglycolamide (TEHDGA) as carrier

Facilitated transport of Am(III) in nitric acid medium using tetra(2-ethyl hexyl) diglycolamide (TEHDGA) in n-dodecane as carrier was studied. It was aimed at finding out the physico-chemical model for the transport of Am(III) using TEHDGA/n-dodecane as carrier under various experimental parameters like feed acidity, carrier concentration, varying strippant, varying membrane pore size, etc. The feed acidity and carrier concentrations were varied from 1 M to 6 M HNO₃ and 0.1 M to 0.3 M TEHDGA/n-dodecane, respectively. The transport of Am(III) increased with increase in feed acidity and carrier concentration reaching maximum at 3 M HNO₃ and 0.2 M TEHDGA/n-dodecane, respectively. Several stripping agents were tested and 0.1 M HNO₃ was found to be the most suitable stripping agent for this system. Almost quantitative transport of Am(III) was observed at about 180 min with feed acidity of 3 M HNO₃, 0.1 M HNO₃ as strippant and 0.2 M TEHDGA/n-dodecane as carrier. The pore size of the membrane support was varied from 0.20 μm to 5 μm and the permeation coefficient increased with increase in pore size up to 0.45 μm (2.43 × 10⁻³ cm/s), and then decreased with further increase in pore size. The plot between permeation coefficient vs. (membrane thickness)⁻¹ was linear which showed that the Am(III) transport was membrane diffusion limited. The membrane diffusion coefficient calculated from the graph was found to be 1.27 × 10⁻⁶ cm²/s and its theoretical value was 1.22 × 10⁻⁶ cm²/s. The stability of the carrier against leaching out of the membrane support as well as the integrity of membrane support was studied over a period of 30 days and was found to be satisfactory within the studied time period.     

Binuclear Schiff base complex of manganese(III) as a neutral carrier for a highly selective iodide electrode.

A new highly selective iodide electrode incorporating a binuclear manganese(III) complex, bis(salicylaldehyde-aminopropanol)dichloroaceticdimanganese(III) [Mn(III)(2)-BSAPDCA], as a neutral carrier is described. The electrode displays an anti-Hofmeister selectivity sequence: iodide > perchlorate > salicylate > thiocyanate > nitrate > bromide > nitrite > chloride > sulfate. The excellent selectivity for iodide is related to a direct interaction between the central Mn(III) atom and iodide and a steric effect associated with the structure of the carrier, which is supported by UV spectroscopy and AC impedance techniques. The electrode exhibits a near-Nernstian potentiometric linear response range to iodide from 1.0 x 10(-1) to 2.0 x 10(-5) mol/L with a detection limit of 8.0 x 10(-6) mol/L and a slope of -60.3 mV/decade in pH 3.0 of phosphate buffer solutions at 20 degrees C. From a comparison of the potentiometric response characteristics between a binuclear manganese(III) complex, Mn(III)(2)-BSAPDCA, and a mononuclear manganese(III) complex, Mn(III)-BSAPB, an enhanced response towards iodide from a binuclear metallic complex-based electrode was observed. The electrode, based on binuclear manganese(III) complex, was successfully applied to the determination of inorganic total iodine in iodized table salt with satisfactory results.