Hydrodynamic voltammetry at tubular electrodes-III Determination of traces of bismuth by differential-pulse anodic-stripping voltammetry at a glassy-carbon tubular electrode with in situ mercury plating

An equation for the current in differential-pulse anodic-stripping voltammetry at tubular electrodes is derived. Application of a glassy-carbon tubular electrode to determination of traces of bismuth in environmental water samples by differential-pulse anodic-stripping voltammetry is described. In hydrochloric acid medium, the stripping peak current is proportional to the concentration of bismuth in the range 2-100 ng/ml, with a deposition time of 3-10 min. The detection limit is 0.5 ng/ml.     

Determination of dinoseb by adsorptive stripping voltammetry using a mercury film electrode

An adsorptive stripping voltammetric method for the determination of the pesticide dinoseb (2-sec.-butyl-4,6-dinitrophenol) at the mercury film electrode is described. The deposition of the mercury film on a glassy carbon disk electrode was optimized. The temperature, at which the mercury film was deposited, was demonstrated to have a strong influence on the stripping peaks, the first one being much more intense than the second. A systematic study of the variables affecting the stripping response was carried out by differential pulse voltammetry. The results obtained have been compared with those at the HMDE; a significant improvement in the sensitivity of the method developed with the MFE was observed. Using a 300 s accumulation time, the limits of determination and detection were 3.6 × 10^–10 and 1.1 × 10^–10 mol L^–1, respectively. The effect of the presence of several herbicides on the dinoseb response was also tested. The method has been applied to the determination of the pesticide in spiked apple juice at two concentration levels: 12.0 and 1.2 g L^–1 of juice.     

Sensitive and selective determination of mercury by differential pulse stripping voltammetry after accumulation of mercury vapour on a gold plated graphite electrode

A selective and sensitive method is proposed for the determination of mercury by anodic stripping voltammetry after its preconcentration from the gas phase. Mercury from the sample solution is reduced to elemental Hg by SnCl₂ and volatilized by the bubbles of a carrier gas. The gas containing mercury vapour is dried and passed through a capillary onto a gold coated graphite electrode. An anodic stripping voltam-mogram is recorded from 0.1 mol/1 HClO₄ + 3 × 10⁻³ mol/1 HCl solution. The calibration curve is linear from 1 × 10⁻⁹ to 4 × 10⁻⁸ mol/1 Hg(NO₃)₂. The absolute detection limit is 0.46 ng Hg. The relative standard deviations for 4 × 10⁻⁹ mol/1 and 2 × 10⁻⁸ mol/1 Hg(NO₃)₂ are 9.8% and 6.1%, respectively n = 5).     

Sensitive and selective determination of mercury by differential pulse stripping voltammetry after accumulation of mercury vapour on a gold plated graphite electrode

 A selective and sensitive method is proposed for the determination of mercury by anodic stripping voltammetry after its preconcentration from the gas phase. Mercury from the sample solution is reduced to elemental Hg by SnCl₂ and volatilized by the bubbles of a carrier gas. The gas containing mercury vapour is dried and passed through a capillary onto a gold coated graphite electrode. An anodic stripping voltammogram is recorded from 0.1 mol/l HClO₄+3×10^-3 mol/l HCl solution. The calibration curve is linear from 1×10^-9 to 4×10^-8 mol/l Hg(NO₃)₂. The absolute detection limit is 0.46 ng Hg. The relative standard deviations for 4×10^-9 mol/l and 2×10^-8 mol/l Hg(NO₃)₂ are 9.8% and 6.1%, respectively (n=5). Received: 18 December 1995/Revised: 16 April 1996/Accepted: 20 April 1996     

Determination of traces of selenium(IV) by cathodic stripping voltammetry at the hanging mercury drop electrode

Conditions convenient for the determination of traces of seIenium(IV) by cathodic stripping technique are described. Several electrolytes were tested. Three procedures are given in which the troublesome splitting of the stripping peak is eliminated. Suitable conditions include perchloric acid solution at elevated temperature, hydrochloric acid solution after preconcentration at zero current, and perchloric acid solution containing a small amount of iodide. The detection limits are 5 × 10^-9, 2 × 10^-9 and 5 × 10^-10 mol dm^-3, respectively. The time required for the entire procedure is about 30 min starting with a soluble seIenium(IV) sample.     

Determination of the antibacterial enrofloxacin by differential-pulse adsorptive stripping voltammetry

Two new methods for the determination of enrofloxacin in commercial formulations and canine urine samples, based on adsorptive stripping voltammetry (AdSV), are proposed. One of the proposed method uses univariate calibration to analyse enrofloxacin in commercial formulations and the other applies principal component regression (PCR) to the voltammetric measurements to determine enrofloxacin in the presence of its metabolite ciprofloxacin. The linear concentration ranges of application were 4-25 and 18-55 ng ml⁻¹ by using an accumulation potential of −0.3 V and a 180 or 60 s accumulation time, respectively for the univariate method. The first concentration range was used for the multivariate method. Both methods were successfully applied to the analysis of commercial formulations and spiked canine urine samples, respectively.     

Determination of arsenic by cathodic stripping voltammetry at a hanging mercury drop electrode

Arsenic (III), respectively arsenic(V) after the reduction were determined in model solutions and some inorganic and organic materials by fast scan differential pulse cathodic stripping voltammetry and by direct current cathodic stripping voltammetry with a rapid increase of potential. The accumulation on a hanging mercury drop electrode followed by cathodic stripping was carried out in 0.7–0.8M HCl or 1–2M H₂SO₄ solutions containing Cu(II)-ions. Detection limits calculated from regression parameters was determined to be under 1 ng/ml for the samples containing very low arsenic concentrations. The relative standard deviation did not reach 8% for arsenic contents about of 5 ng/ml.     

Determination of pseudouridine at submicromolar concentrations by cathodic stripping voltammetry at a mercury electrode

Pseudouridine (5-ribosyluracil), uridine (N,1-ribosyluracil), deoxyuridine (N,1-deoxyribosyluracil) and uracil are investigated by means of d.c. polarography and by differential and normal pulse polarography. Pseudouridine, which is known to be a cancer marker, yields anodic polarographic currents in the pH range 7–11, whereas uridine and deoxyuridine are inactive under the same conditions. The polarographic response of pseudouridine obtained is due to the formation of a sparingly soluble mercury compound. Pseudouridine can be determined by differential pulse polarography in the concentration range 2–6 × 10^?6 M and by differential-pulse cathodic stripping voltammetry at concentrations two orders of magnitude lower. Small excesses of uridine, deoxyuridine or proteins do not interfere with the determination.     

Determination of trace metals in rain water by differential-pulse stripping voltammetry

Differential-pulse stripping voltammetry is applied to measure zinc, cadmium, lead and copper by anodic stripping and selenium(IV) by cathodic stripping in rain water at pH 2; subsequently, at pH 9,1, manganese is measured by anodic stripping on the same portion, and cobalt and nickel are measured in the adsorptive mode after formation of their dimethylglyoximates. The instrumental parameters are optimized. The linear ranges, mutual interferences and detection limits are studied. Excellent accuracy is demonstrated; the standard deviation is around 15% at 2.5–50 μg l^?1 levels. The method is shown to be applicable for rain water.     

Determination of ceftriaxone in biological material by differential-pulse adsorptive stripping voltammetry

Differential-pulse adsorptive stripping voltammetry was used to determine sub-micromolar concentrations of ceftriaxone in plasma. A hanging mercury drop electrode was chosen as the working electrode. A simple clean-up procedure was developed in which ceftriaxone was extracted from blood plasma with the non-ionic resin Amberlite XAD-2 and eluted with methanol. The recovery from plasma was 97.6% using a 1.52 x 10(-4) M stock ceftriaxone solution. The method was applied to caesarean cases, and total ceftriaxone levels were measured in the maternal and umbilical cord blood. The amount of ceftriaxone transmitted to the baby on administration of the drug to the mother before the caesarean operation was found to be in the range 0.067-0.17%.     

Determination of total copper in haemodialysis water by differential-pulse anodic stripping voltammetry

An anodic stripping voltammetric method was developed in order to determine copper in the water used to prepare haemodialysis solutions. The interference from organic matter was overcome by high-pressure bomb mineralization. The electrochemical results were compared with those obtained by using graphite furnace atomic absorption spectrometry and the correlation was excellent (r = 0.983, p < 0.001). The detection limit was 0.2 μg l^?1 copper.     

Determination of trace arsenic(III) by differential-pulse anodic stripping voltammetry with in-situ plated bismuth-film electrode

Abstract

A systematic survey of the quality status of the main aquifers in rural areas of Catalonia (Spain) regarding pesticide pollution has been carried out. A total number of 139 wells, distributed among 13 different hydrogeological units have been sampled and analyzed by GC-MS and GC-ECD, during the period 1997—98. Pesticides monitored were selected among triazine herbicides, organochlorine and organophosphorus insecticides. A positive presence of pesticides has been detected in 84.2% of the samples analyzed, 23.7% of them exceeding the requirements of the EU drinking water Directive (98/83/CE). Organochlorine insecticides were present in 62.6% of the samples, triazines in 49% and organophosphorus insecticides in 28.8%. The results obtained have been interpreted by Principal Component Analysis.     

Determination of traces molybdenum by catalytic adsorptive stripping voltammetry

A reliable and very sensitive procedure for the determination of ultra trace of molybdenum is proposed. Molybdenum was determined by cathodic stripping differential pulse voltammetry based on the adsorption collection of the Mo(VI)-Tiron complex on a hanging mercury drop electrode (HMDE). The variation of peak current with pH, concentration of Tiron and chlorate, plus several instrumental parameters such as accumulation time, accumulation potential and scan rate, were optimized. Under optimized condition, the relationship between the peak current and molybdenum concentration is linear in the range of 0.010-21.0 ng ml⁻¹. The limit of detection was found to be 0.006 ng ml⁻¹. The relative standard deviation for 10 replicates determination of 0.6 and 10 ng ml⁻¹ Mo(VI) is equal to 1.3 and 0.9%, respectively. The method was applied to the determination of molybdenum in river water, tap water, well water, plant foodstuff samples such as cucumber, tomato, carrot, and certified steel reference materials.     

Anodic stripping voltammetry at a nickel-based mercury film electrode

The electrochemical properties of the nickel-based mercury film electrode (Ni-MFE) were investigated with respect to application of the electrode in the anodic stripping voltammetry (a.s.v.) of heavy metal ions. The hydrogen overpotential at the Ni-MFE is higher than those at MFEs based on other metals, and high enough to get quantitative a.s.v. peaks of lead and cadmium. The mercury film of the Ni-MFE is stable both mechanically and chemically; a.s.v. peaks at a Ni-MFE which had been used fifty times within 300 h after its preparation were identical with those at the freshly prepared electrode. With the Ni-MFE, 5 × 10^?10–10^?7 M lead(II) and 2 × 10^?10–10^?7 M cadmium(II) in the solution can be determined with relative standard deviations of 11 and 12%, respectively. These results are comparable to those obtained by a.s.v. at an in situ mercury-plated g]assy carbon electrode.     

Determination of folic acid by adsorptive stripping voltammetry at the static mercury drop electrode

Folic acid can be determined at nanomolar concentrations by controlled adsorptive accumulation of folic acid on a static mercury drop electrode held at ?0.3 V vs. Ag/AgCl followed by reduction of the surface species. In 0.1 M sulfuric acid, a cathodic scan gives peaks at ?0.47 v and ?0.75 V vs. Ag/Agcl; the latter peak provides greater sensitivity. Differential-pulse stripping is shown to be superior to normal-pulse and d.c. stripping. After a 5-min preconcentration, the detection limit is about 1 × 10^?10 M folic acid. The adsorptive stripping response is evaluated with respect to concentration dependence, preconcentration time and potential, solution acidity and the presence of gelatin and bromide. The relative standard deviation at the 5 × 10^?8 M level is 1.2%. This method is applied to the determination of folic acid in pharmaceutical tablets.     

Determination of gallium traces by differential pulse anodic stripping voltammetry

Summary The determination of gallium traces is carried out on the hanging drop mercury electrode in solutions of low ionic strength and in absence of complexing agents. At pH=3.2, where stable solutions are obtained, concentrations of 0.2 g Ga l^–1 are determinated with a standard deviation of 0.96% and a detection limit of 4 ng Ga l^–1.The effect of various instrumental parameters is investigated and optimized conditions established. The theory of differential pulse anodic stripping voltammetry is verified with the results obtained experimentally. The use of salicylate as base electrolyte is also considered.

---

Bestimmung von Galliumspuren durch Differentialpuls-Anodic Stripping-Voltammetrie

     

Heated mercury film electrode for anodic stripping voltammetry

A directly heated mercury film electrode (MFE) extends the operational capabilities of the hot layer technique to a wide range of electroanalytical systems. Wires or layers of gold and platinum have been used as sensors so far, but they were suitable only for the analysis of a small number of metals. The development of a heated MFE is described, including electrode construction and mercury deposition procedures. The thermal properties of the sensor were investigated. As a first application, cadmium was determined by anodic stripping voltammetry (ASV) with the result of an improved signal-to-background ratio.