Processing of neutron activation analysis data using a general purpose PDP-11 minicomputer

A minicomputer system is described for the off-line reduction of gamma spectral data from neutron activation analysis. The hardware and software systems are described. Both data printouts and spectral plots are produced. The versatility of system permits the availability of computer capability for both on- and off-line functions in a variety of analytical techniques at a moderate cost and under the control of the experimenter.     

Study of ionic-to-atomic line intensity ratios for two axial viewing-based inductively coupled plasma atomic emission spectrometers

Using two axially-viewed inductively coupled plasma (ICP) systems that exhibited different behaviors to matrix effects, the sensitivity of the Mg II 280.270 nm/ Mg I 285.213 nm line intensity ratio to the ICP operating conditions and to matrix effects was compared to that observed for alternative ionic-to-atomic line intensity ratios such as the Cd II 226.502 nm/Cd I 228.802 nm, Cr II 267.716 nm/Cr I 357.868 nm, Ni II 231.604 nm/Ni I 232.138 nm, Pb II 220.353 nm/Pb I 217.000 nm, and Zn II 206.200 nm/Zn I 213.857 nm ratios. Both robust and non-robust conditions were used. Some lines behaved differently, in particular the Mg I and Cr I lines, not only as a function of the matrix, but also as a function of the ICP system. The Mg II/Mg I ratio was found to remain a good compromise to follow changes in plasma conditions. The use of several ionic-to-atomic line ratios confirmed that axial viewing leads to matrix effects that are particularly sensitive for atomic lines. The effects cannot be totally suppressed, even under robust conditions, and regardless of the ICP system. An alternative to minimize matrix effects was the use of a buffer such as Cs at 10 g l⁻¹.     

Development of transient data acquisition system for hyphenated techniques coupled with inductively coupled plasma atomic emission spectrometry

A transient data acquisition system for flow injection analysis (FIA), high performance liquid chromatography (HPLC), and electrothermal vaporization (ETV) combined with ICP-AES multi-element instrumentation was developed and successfully applied to the analysis of different types of samples, including human serum, human hair and tea, for simultaneous multi-element determinations. The accuracy of the method was verified with hair reference material. Good agreement between the experimental results and certified values, and also satisfactory recoveries from standard additions, were achleved.     

Speciation of butyltin compounds by ion chromatography coupled to electrothermal atomic absorption spectrometry

A new method for the determination of butyltin species by ion-exchange chromatography linked with graphite-furnace electrothermal atomic absorption spectrometry (ETAAS) is presented. The separation is achieved on a strong cation-exchange column with a 0.18 mol dm^?3 solution of diammonium citrate at pH 6.5 with a step change to pH 4.0 in 60:40 methanol/water solvent. ETAAS detection is performed on-line using an oxidizing matrix modifier. Mono-, di- and tri-butyltin may be determined in a single experiment with detection limits of (respectively) 0.5, 1.1 and 0.8 ng (Sn). Applications to actual samples are reported.     

Separation and preconcentration by flow injection coupled to tungsten coil electrothermal atomic absorption spectrometry

A flow injection system coupled to a tungsten coil electrothermal atomizer has been developed for on-line separation and preconcentration, using lead as a model element. The system utilizes three-way solenoid valves for sampling, buffering, washing and reconditioning solution management, and the resin column is inserted in the tip of the autosampler arm of a Varian GTA-96. The solenoid valves and tungsten coil power supply were controlled by a computer program written in Visual Basic, interfaced with the built-in Varian software. The system performance was tested by loading the resin column with the sample flowing at 3 ml min⁻¹ for 60 s. Elution was performed automatically by sampling 20 μl of the eluent from a sample cup of the autosampler, and this aliquot was delivered into a 150 W tungsten coil. With Chelex-100 resin, the separation of concomitants was tested with lead in the presence of as much as 1000 mg l⁻¹ of Ca, Mg, Na or K. The model system presented an enrichment factor of 64 at a sampling rate of 30 samples per hour.     

Continuous ultrasound-assisted extraction coupled to a flow injection-flame atomic absorption spectrometric system for calcium determination in seafood samples

Calcium was extracted on-line from solid seafood samples by a simple and rapid continuous ultrasound-assisted extraction system. This system is connected to a flow injection manifold, which allows the on-line flame atomic absorption spectrometric determination of calcium. This method enables the analysis of solid samples avoiding time-consuming traditional sample preparation methods and their inherent errors. The on-line manifold for calcium determination is the simplest possible, because a volume of 250 L of acid extract is injected into an ultrapure water carrier stream. The acid extract was diluted on-line with lanthanum, which also acts as masking agent in order to avoid chemical interferences. The continuous monitoring of the calcium signal was accomplished by flame atomic absorption spectrometry. A Plackett-Burman experimental design was used for the optimisation of the continuous leaching procedure. The method allowed a total sampling frequency of 40 samples per hour, with a relative standard deviation for the complete procedure of 0.9% (for a sample containing 3414.35 mg/kg calcium (dry mass)). The limit of detection was found to be 44.4 mg/kg (dry mass) for 5 mg of sample. The analytical procedure was applied to real seafood samples.     

Flow injection on-line ultrasound-assisted extraction of iron in meat samples coupled to a flame atomic absorption spectrometric system

Iron was extracted on-line from solid meat samples by a simple and rapid continuous ultrasound-assisted extraction system (CUES). The CUES is connected to a flow injection manifold, which allows the on-line flame atomic absorption spectrometric determination of iron. A Plakett–Burman design was used for the optimisation of the CUES. The method achieved a total sampling frequency of 11 samples per hour with a relative standard deviation for the complete procedure of 0.4%. The detection limit was 0.6 g g^–1 (dry mass) for a sample amount of 30 mg. Accurate results were obtained by measuring the certified reference materials BCR-186 (pig kidney) and BCR-184 (bovine muscle). The analytical procedure was applied to different real meat samples with satisfactory results.     

Peat as a natural solid-phase for copper preconcentration and determination in a multicommuted flow system coupled to flame atomic absorption spectrometry

The physical and chemical characteristics of peat were assessed through measurement of pH, percentage of organic matter, cationic exchange capacity (CEC), elemental analysis, infrared spectroscopy and quantitative analysis of metals by ICP OES. Despite the material showed to be very acid in view of the percentage of organic matter, its CEC was significant, showing potential for retention of metal ions. This characteristic was exploited by coupling a peat mini-column to a flow system based on the multicommutation approach for the in-line copper concentration prior to flame atomic absorption spectrometric determination. Cu(II) ions were adsorbed at pH 4.5 and eluted with 0.50 mol L⁻¹ HNO₃. The influence of chemical and hydrodynamic parameters, such as sample pH, buffer concentration, eluent type and concentration, sample flow-rate and preconcentration time were investigated. Under the optimized conditions, a linear response was observed between 16 and 100 μg L⁻¹, with a detection limit estimated as 3 μg L⁻¹ at the 99.7% confidence level and an enrichment factor of 16. The relative standard deviation was estimated as 3.3% (n = 20). The mini-column was used for at least 100 sampling cycles without significant variation in the analytical response. Recoveries from copper spiked to lake water or groundwater as well as concentrates used in hemodialysis were in the 97.3-111% range. The results obtained for copper determination in these samples agreed with those achieved by graphite furnace atomic absorption spectrometry (GFAAS) at the 95% confidence level.     

Solid sampling coupled to flame furnace atomic absorption spectrometry for Mn and Ni determination in petroleum coke

A solid sampling flame furnace atomic absorption spectrometry (SS-FF-AAS) system was developed for Mn and Ni determination in petroleum coke. The proposed system for solid sampling was a quartz cell with two perpendicular tubes (T-shaped tubes), positioned above the burner. Manganese and Ni determination was made using an atomic absorption spectrometer with deuterium background corrector, air-acetylene flame and a single slit burner. Powdered samples of coke were introduced as pellets (up to 62 mg) into the quartz cell with a movable hollow quartz piston. When the sample pellet reached the end of quartz cell (T-connection), in the presence of a constant oxygen flow, it quickly burned and the combustion products were transferred to the upper slit tube where the atomic absorption process occurs. Calibration was possible using aqueous reference solutions applied directly on high purity graphite pellets. Results obtained for Mn and Ni using the proposed SS-FF-AAS system were compared to those obtained by inductively coupled plasma optical emission spectrometry (ICP OES) and inductively coupled plasma mass spectrometry (ICP-MS) after sample decomposition by high pressure microwave assisted acid digestion and also by microwave induced combustion. Agreement better than 96% was obtained for both methods employing a previous step of sample digestion (ICP OES and ICP-MS) and by SS-FF-AAS. Accuracy was evaluated using certified reference materials and also recovery tests. The relative standard deviation was lower than 9% for both analytes. The characteristic mass was 18.3 and 14.7 ng and the limit of detection was 0.6 and 0.8 µg g^− 1 for Mn and Ni, respectively. The proposed SS-FF-AAS system can be applied for Mn and Ni determination in petroleum coke, combining a relatively high sample throughput (9 determinations per h), and a suitable precision and accuracy.     

Atomization from a tantalum surface in graphite furnace atomic absorption spectrometry

The mechanism of atom formation of U, V, Mo, Ni, Mn, Cu and Mg atomized from pyrolytic graphite and tantalum metal surfaces has been studied. The mechanism of atom formation for U from a graphite tube atomizer is reported for the first time. The peak absorbance for U and Cu is increased by factors of 59.7 and 2.0, respectively, whereas that of V, Mo and Ni is reduced by several orders of magnitude when they are atomized from a tantalum metal surface. The peak absorbance of Mn and Mg is not appreciably affected by the material of the atomization surface. Interaction of Mn and Mg with the graphite surface and formation of their refractory carbides was found to be negligible. Uranium forms a refractory carbide when heated from a graphite surface.     

Continuous ultrasound-assisted extraction of cadmium from legumes and dried fruit samples coupled with on-line preconcentration-flame atomic absorption spectrometry

Cadmium was continuously extracted with diluted nitric acid from legumes and dried fruit samples using a simple, rapid and continuous ultrasound-assisted extraction system. A minicolumn packed with a chelating resin (Chelite P, with aminomethylphosphoric acid groups) was placed between the extraction unit and the detector for cadmium preconcentration. The cadmium content in the acid extract was retained into the minicolumn, and elution was carried out with hydrochloric acid, with this trace metal continuously monitored by flame atomic absorption spectrometry. An experimental design (Plackett-Burman 2⁶×3/16) was used to optimize the continuous leaching procedure and the preconcentration step. The method allowed a total sampling frequency of 10 and 14 samples per hour for legumes and dried fruit, respectively. The procedure displayed good precision (2.0 and 2.5%, respectively, expressed as relative standard deviations) for samples containing 0.202±0.005 g g^–1 Cd (broad bean) and 0.239±0.004 g g^–1 Cd (peanut). Detection limits of 0.014 g g^–1 Cd for 60 mg of legume samples and 0.011 g g^–1 Cd for 80 mg of dried fruit samples were obtained. The method was successfully applied to the determination of trace amounts of cadmium in legumes and dried fruit samples.     

Flow injection on-line sorption preconcentration of platinum in a knotted reactor coupled with electrothermal atomic absorption spectrometry

A flow injection on-line sorption preconcentration method for the electrothermal AAS determination of platinum has been developed. The pyrrolidine dithiocarbamate complexes of either Pt⁴⁺ or Pt²⁺, formed in 0.7 mol L^–1 HNO₃, are on-line adsorbed on the inner walls of a PTFE knotted reactor and subsequently eluted with methanol. An enhancement factor of 112 and a detection limit (3 σ) of 10 ng L^–1 along with a sampling frequency of 21 h^–1 are achieved with a 90 s preconcentration time at a sample flow rate of 8.8 mL min^–1. The relative standard deviation is 2.5% for 0.4 μg L^–1 Pt. The method has been applied to the determination of platinum in blood samples. Received: 6 October 1997 / Revised: 26 November 1997 / Accepted: 3 December 1997     

Simultaneous cloud-point extraction of nine cations from water samples and their determination by flame atomic absorption spectrometry.

The cloud-point methodology was successfully employed for the preconcentration of heavy metal cations at trace levels from aqueous samples prior to flame atomic absorption spectrometry (FAAS). Cations were taken into a complex with 8-quinolinol in an aqueous non-ionic surfactant, Triton X-114, medium and concentrated in the surfactant rich phase by bringing the solution to the cloud-point temperature. The preconcentration of only 100 mL of the solution with 1% Triton X-114 and 10(-3) M 8-quinolinol at pH 7.0 gave a preconcentration factor higher than 100 for most cations. Under these conditions, the detection limits of the cloud-point extraction-FAAS system were 0.8 - 15 microg/L.     

Flow injection on-line sorption preconcentration of platinum in a knotted reactor coupled with electrothermal atomic absorption spectrometry

A flow injection on-line sorption preconcentration method for the electrothermal AAS determination of platinum has been developed. The pyrrolidine dithiocarbamate complexes of either Pt⁴⁺ or Pt²⁺, formed in 0.7 mol L^–1 HNO₃, are on-line adsorbed on the inner walls of a PTFE knotted reactor and subsequently eluted with methanol. An enhancement factor of 112 and a detection limit (3 σ) of 10 ng L^–1 along with a sampling frequency of 21 h^–1 are achieved with a 90 s preconcentration time at a sample flow rate of 8.8 mL min^–1. The relative standard deviation is 2.5% for 0.4 μg L^–1 Pt. The method has been applied to the determination of platinum in blood samples.     

On-line preconcentration and determination of cadmium in honey using knotted reactor coupled to flow injection-flame atomic absorption spectrometry

An on-line cadmium preconcentration and determination system implemented with flame atomic absorption spectrometry (FAAS) associated with flow injection was studied. Cadmium was retained as Cd-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol Cd-(5-Br-PADAP) complex, pH 9.3. The Cd complex was removed from the knotted reactor (KR) with ethanol. A total enhancement factor of 140 was obtained with respect to FAAS (40 for KR and 3.5 due to the use of ethanol) with preconcentration time of 120 s. The detection limit value for preconcentration of 1 g sample was 0.5 ng/g. The repeatability for 10 replicate determinations at 5.0 ng/g Cd level was 3.5% relative standard deviation, calculated from peak heights obtained. The calibration graph using the preconcentration system for Cd was linear with a correlation coefficient of 0.9990 at levels near the detection limits to at least 2000 ng/g. The method was successfully applied to determination of total Cd in honey samples.     

On-line determination of palladium by flame atomic absorption spectrometry coupled with a separation/preconcentration minicolumn containing a new sorbent

A method was developed for the on-line determination of palladium in complex matrices with flame atomic absorption spectrometry (FAAS) using Amberlite XAD-16 resin functionalized with 2-[2-(5-thiol-1,3,4-thiadiazolyl)]-azonaphthol (TTAN) reagent. Optimum experimental conditions such as pH of sample, type of eluent, amount of resin, volumes of sample and eluent solution, flow rates of sample and eluent, and effect of interfering ions were established. A 0.1?mol?L^?1 thiourea solution in 0.5?mol?L^?1 HCl was used as the eluent and subsequently transportation the analyte ions into the nebulizer–burner system for atomization. The synthesized chelating resin material showed excellent chemical and mechanical resistance, fast adsorption kinetics permitting the use of high sample flow rates without significant losses of retention efficiency. The detection limit of the method was 1.5?µg?L^?1 while the relative standard deviation (RSD%) was 2.4% at 0.1?mg?L^?1 Pd(II) level. The developed method was successfully applied to the determination of palladium in the catalytic converter and water samples.     

Trace level determination of cadmium in wine by on-line preconcentration in a 5-Br-PADAP functionalized wool-packed microcolumn coupled to flame atomic absorption spectrometry

An on-line retention and preconcentration system based on a sheep wool-packed microcolumn combined with flame atomic absorption spectrometry is proposed for trace level determination of Cd in wine. A chelating reagent 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol was immobilized onto the wool before retention of the analyte. Several factors influencing the preconcentration efficiency of Cd and his subsequent determination, such as pH, eluent type, sample and eluent flow rates, interfering effects, were studied. A preconcentration factor of 39 was obtained with only 20 mL of sample. The relative standard deviation for five determinations of 1 μg L⁻¹ Cd was 3.4%. The calibration graph was linear with a correlation coefficient of 0.998 at levels near the detection limit and up to at least 25 μg L⁻¹. The limit of detection was 37 ng L⁻¹. The accuracy of the proposed methodology was tested by comparison of the results with those obtained by electrothermal atomic absorption spectrometry analysis along with a recovery study. Finally, the method was employed for evaluating Cd levels in different wines including, blank, rose, and red.