Thermal conductivities of solid and liquid phases for neopentylglycol, aminomethylpropanediol and their binary alloy

The variations of thermal conductivities of solid phases versus temperature for neopentylglycol (NPG), 2-amino-2-methyl-1,3-propanediol (AMPD) and AMPD-42.2 mol% NPG alloy were measured with a radial heat flow apparatus. From the graphs of the solid phases thermal conductivity variations versus temperature, the thermal conductivities of the solid phases at their melting temperature and temperature coefficients for same materials were also found to be 0.22±0.01, 0.45±0.02 and 0.32±0.02 W/Km and 0.0047, 0.0031 and 0.0043 K⁻¹, respectively. The thermal conductivity ratios of liquid phase to solid phase for the same materials at their melting temperature are found to be 1.07, 1.12 and 0.74 with a Bridgman type directional solidification apparatus, respectively. Thus, the thermal conductivities of liquid phases for pure NPG, pure AMPD and AMPD-42.2 mol% NPG alloy at their melting temperature were evaluated to be 0.24, 0.50 and 0.23 W/Km, respectively, by using the values of solid phase thermal conductivities and the thermal conductivity ratios of liquid phase to solid phase.     

The effect of particle size on the thermal conductivity of alumina nanofluids

We present new data for the thermal conductivity enhancement in seven nanofluids containing 8–282 nm diameter alumina nanoparticles in water or ethylene glycol. Our results show that the thermal conductivity enhancement in these nanofluids decreases as the particle size decreases below about 50 nm. This finding is consistent with a decrease in the thermal conductivity of alumina nanoparticles with decreasing particle size, which can be attributed to phonon scattering at the solid–liquid interface. The limiting value of the enhancement for nanofluids containing large particles is greater than that predicted by the Maxwell equation, but is predicted well by the volume fraction weighted geometric mean of the bulk thermal conductivities of the solid and liquid. This observation was used to develop a simple relationship for the thermal conductivity of alumina nanofluids in both water and ethylene glycol.     

Constant electrical resistivity of Zn along the melting boundary up to 5 GPa

We measured the electrical resistivity of high purity Zn along the melting boundary, up to 5?GPa in a large volume press. The electrical resistivity remained constant on the melting boundary, as predicted in a thermodynamics-based model for simple metals. The effects of pressure and temperature on the electrical resistivity of the solid and liquid states are interpreted in terms of their antagonistic effects on the electronic structure of Zn. Within the error of measurements, our melting temperature data agree well with those of the previous studies. The electronic thermal conductivity was calculated from resistivity data using the Wiedemann–Franz law and shows a decrease with temperature in the solid state and an increase in the liquid state, with a large decrease on melting. Comparison of calculated electronic and measured total thermal conductivities indicates that the electronic component dominates over the phonon component in Zn.     

Investigation on characteristics of thermal conductivity enhancement of nanofluids

It has been shown that a nanofluid consisting of nanoparticles dispersed in base fluid has much higher effective thermal conductivity than pure fluid. In this study, four kinds of nanofluids such as multiwalled carbon nanotube (MWCNT) in water, CuO in water, SiO₂ in water, and CuO in ethylene glycol, are produced. Their thermal conductivities are measured by a transient hot-wire method. The thermal conductivity enhancement of water-based MWCNT nanofluid is increased up to 11.3% at a volume fraction of 0.01. The measured thermal conductivities of MWCNT nanofluids are higher than those calculated with Hamilton–Crosser model due to neglecting solid–liquid interaction at the interface. The results show that the thermal conductivity enhancement of nanofluids depends on the thermal conductivities of both particles and the base fluid.     

A Ubiquitous Thermal Conductivity Formula for Liquids,Polymer Glass,and Amorphous Solids

The microscopic mechanism of thermal transport in liquids and amorphous solids has been an outstanding problem for a long time.There have been several approaches to explain the thermal conductivities in these systems, for example, Bridgman's formula for simple liquids, the concept of the minimum thermal conductivity for amorphous solids, and the thermal resistance network model for amorphous polymers.Here, we present a ubiquitous formula to calculate the thermal conductivities of liquids and amorphous solids in a unified way, and compare it with previous ones.The calculated thermal conductivities using this formula without fitting parameters are in excellent agreement with the experimental data.Our formula not only provides a detailed microscopic mechanism of heat transfer in these systems, but also resolves the discrepancies between existing formulae and experimental data.     

Different effects of grain boundary scattering on chargeand heat transport in polycrystalline platinum and goldnanofilms

The in-plane electrical and thermal conductivities of several polycrystalline platinum and gold nanofilms with different thicknesses are measured in a temperature range between the boiling point of liquid nitrogen (77K) and room temperature by using the direct current heating method. The result shows that both the electrical and thermal conductivities of the nanofilms reduce greatly compared with their corresponding bulk values. However, the electrical conductivity drop is considerably greater than the thermal conductivity drop, which indicates that the influence of the internal grain boundary on heat transport is different from that of charge transport, hence leading to the violation of the Wiedemann--Franz law. We build an electron relaxation model based on Matthiessen's rule to analyse the thermal conductivity and employ the Mayadas & Shatzkes theory to analyse the electrical conductivity. Moreover, a modified Wiedemann--Franz law is provided in this paper, the obtained results from which are in good agreement with the experimental data.     

The role of interfacial layers in the enhanced thermal conductivity of nanofluids: A renovated Hamilton–Crosser model

We previously developed a renovated Maxwell model for the effective thermal conductivity of nanofluids and determined that the solid/liquid interfacial layers play an important role in the enhanced thermal conductivity of nanofluids. However, this renovated Maxwell model is limited to suspensions with spherical particles. Here, we extend the Hamilton--Crosser model for suspensions of nonspherical particles to include the effect of a solid/liquid interface. The solid/liquid interface is described as a confocal ellipsoid with a solid particle. The new model for the three-phase suspensions is mathematically expressed in terms of the equivalent thermal conductivity and equivalent volume fraction of anisotropic complex ellipsoids, as well as an empirical shape factor. With a generalized empirical shape factor, the renovated Hamilton--Crosser model correctly predicts the magnitude of the thermal conductivity of nanotube-in-oil nanofluids. At present, this new model is not able to predict the nonlinear behavior of the nanofluid thermal conductivity.     

Calculation of the effective thermal conductivity of powders formed by spherical particles in a gaseous atmosphere

We describe a method for calculating the effective thermal conductivity of powders formed by spherical particles with a size exceeding 1 μm in a gaseous atmosphere in wide ranges of temperatures and pressures. We take into account the structural factor of the powder medium, adsorption of gas on the surface of solid spheres, the temperature dependences of the thermal conductivities of the powder components, and the formation of melt necks between the spheres after the attainment of the melting point. In the case of complete melting of the spheres, we propose a model for thermal conductivity of the melt with gas inclusions. The results of calculation of the effective thermal conductivity are in good agreement with experimental data.     

Thermal and electrical conductivities of silver–indium–tin alloys

The variations of thermal conductivity with temperature for the Ag–[x] wt% Sn–20 wt% In alloys (x=8, 15, 35, 55 and 70) were measured using a radial heat flow apparatus. From the graphs of thermal conductivity versus temperature, the thermal conductivities of solid phases at their melting temperature for the Ag–[x] wt% Sn–20 wt% In alloys (x=8, 15, 35, 55 and 70) were found to be 46.9±3.3, 53.8±3.8, 61.2±4.3, 65.1±4.6 and 68.1±4.8 W/Km, respectively. The variations of electrical conductivity of solid phases versus temperature for the same alloys were determined from the Wiedemann–Franz equation using the measured values of thermal conductivity. From the graphs of electrical conductivity versus temperature, the electrical conductivities of the solid phases at their melting temperatures for the Ag–[x] wt% Sn–20 wt% In alloys (x=8, 15, 35, 55 and 70) alloys were obtained to be 0.036, 0.043, 0.045, 0.046 and 0.053 (×10⁸/Ωm), respectively. Dependencies of the thermal and electrical conductivities on the composition of Sn in the Ag–Sn–In alloys were also investigated. According to present experimental results, the thermal and electrical conductivities for the Ag–[x] wt% Sn–20 wt% In alloys linearly decrease with increasing the temperature and increase with increasing the composition of Sn.     

无锂助熔剂B_2O_3对Li_(1.3)Al_(0.3)Ti_(1.7)(PO_4)_3固体电解质离子电导率的影响

采用固相法制备锂离子电池用固体电解质磷酸钛锂铝Li_(1.3)Al_(0.3)Ti_(1.7)(PO_4)_3(LATP),研究了不同烧结温度以及助熔剂对LATP固体电解质离子电导率的影响.采用X射线衍射、能谱分析、扫描电镜和交流阻抗等方法,研究样品的结构特征、元素含量、形貌特征以及离子导电性能.结果表明,在900?C烧结可以获得结构致密、离子电导率较高的纯相LATP陶瓷固体电解质.与添加助熔剂Li BO2的样品进行对比实验发现,采用B_2O_3代替LiBO_2作为助熔剂也可以提高烧结样品的离子电导率,并且电解质的离子电导率随助熔剂添加量的增大,先增大后减小,其中添加质量百分比为2%的B_2O_3的样品具有最高的室温离子电导率,为1.61×10~(-3)S/cm.     

The Role of Interfacial Layers in the Enhanced Thermal Conductivity of Nanofluids: A Renovated Maxwell Model

Nanofluids, a new class of solid/liquid suspensions, offer scientific challenges because their measured thermal conductivity is one order of magnitude greater than predictions. It has long been known that liquid molecules close to a solid surface form layered solid-like structures, but little is known about the connection between this nanolayer and the thermal properties of the suspensions. Here, we have modified the Maxwell equation for the effective thermal conductivity of solid/liquid suspensions to include the effect of this ordered nanolayer. Because this ordered nanolayer has a major impact on nanofluid thermal conductivity when the particle diameter is less than 10 nm, a new direction is indicated for development of next-generation coolants.     

A method to calculate the thermal conductivity of HMX under high pressure

A method based on Debye theory is developed to calculate the thermal conductivity of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX). The phonon–phonon interaction model is built up for solid HMX. The phonon lifetime formula is derived by the phonon–phonon scattering mechanism, and the thermal conductivity tensor is derived by the phonon dispersion model. The thermal conductivities of α/β/δ-HMX are calculated in the temperature range 0–700?K and pressure range of 0–10?GPa. The phonon softening process of HMX is investigated. We have proven that the Debye frequency and thermal conductivity tend to 0 at the phonon softening point. A physical picture of the phonon–phonon interaction, phonon lifetime and phonon softening is built up.     

Characterization of Powder Beds by Thermal Conductivity: Effect of Gas Pressure on the Thermal Resistance of Particle Contact Points

The thermal conductivity of ceramic powder packed beds was measured at temperatures below 100 °C for various powder sizes and compositions and under different gas atmospheres. Measurements at low pressures (down to 10 Pa) combined with a theoretical model allowed the elucidation of geometrical and thermal resistance parameters for the contact points between granules. The gap thickness and contact point size were found to be well correlated with the mean particle size. The thermal conductivities of all powders at low pressure were found to differ at most by a factor of two, whereas the solid‐phase conductivities of the powder materials differed by more than one order of magnitude. A theoretical model accounting for the size‐dependence of contact point conductivity is incorporated to rationalize this trend.     

Physicochemical properties of ionic liquids based on imidazolium/pyrrolidinium cations and maleate/phthalate anions

Ionic liquids (ILs) based on imidazolium/pyrrolidinium cations and maleate/phthalate anions can be used as excellent electrolyte materials for electrolytic capacitors. In this study, we synthesized four ILs of this family and investigated their thermal behaviors, ionic conductivities and sparking voltages. The four ILs have high thermal stability for capacitor requirements. The conductivities of imidazolium ILs are slightly higher than those of pyrrolidinium analogs and the conductivities of maleate anion-based ILs are higher than those of corresponding phthalate anion-based ILs. Besides, the long-term thermal stability of imidazolium ILs in conductivity is superior to that of pyrrolidinium analogs. Whereas the long-term thermal stability of phthalate anion-based ILs is better than that of corresponding maleate anion-based ILs. The influence of cationic structure of the ILs on conductivity was analyzed. The temperature dependence of conductivity was also discussed in this work. The Vogel–Tammann–Fulcher (VTF) equation accurately describes the temperature dependence of conductivity for the ILs. In addition, the result of sparking voltage measurement shows that neither Ikonopisov nor Albella model is valid for the ILs.     

近固体表面拟有序液体边界层的导热研究

本文用分子动力学模拟方法研究了近固体壁面拟有序液体边界层及其导热特性。得出分子密度沿垂直壁面方向呈衰减分布,且拟有序层内的分子运动方式接近于晶体分子。结合径向分布函数定量分析得出拟有序层的有序程度随固液耦合作用加强而增加。用G-K公式计算了拟有序层的导热系数,发现其与物件尺度、边界条件有密切关系。但在相同的边界条件下,导热系数随有序程度的增加而增加。     

Thermal conductivity and expansion of PbF2 single crystals

In order to check a phenomenon of the negative correlation between ionic and thermal conductivities of solid substances, we studied the thermal conductivity and expansion of cubic PbF₂ single crystals at 50–300 and 5.6–317 K, respectively. We found that lead difluoride had a thermal expansion coefficient α that was equal to (28.5 ± 0.3)10⁻⁶ K⁻¹ at 300 K, and a thermal conductivity coefficient k(T) was equal to 1.40 ± 0.07 W/(m K) at the same temperature. Thus, the thermal conductivity for PbF₂ is the lowest among fluorite-type MF₂ (M = Ca, Sr, Ba, Cd, Pb) thermal conductivities, whereas its fluoride-ion conductivity is the highest one among MF₂ (M = Ca, Sr, Ba, Cd, Pb) ionic conductors.

     

纳米ZnO／石蜡复合相变材料的热物理性质研究

本文通过将纳米氧化锌（ZnO）颗粒加入熔融的石蜡（PW）并进行搅拌和超声制备了一种纳米ZnO／PW复合相变储能材料。为使纳米氧化锌在基体物质中分散均匀,在制备过程中使用了搅拌和超声以制备均匀的复合材料。使用扫描电镜观察其微观结构表明氧化锌在石蜡中分散良好。对所得ZnO／PW复合相变材料的相变温度、相变焓及导热系数等热物...     

Vacancy-induced heat transfer in solid Kr and Ar

We have measured constant-volume thermal conductivities of solid krypton at six molar volumes between 28.84 and 29.54 cm³ mole^?1 and of solid argon at a molar volume of 24.30 cm³ mole^?1 at temperatures of order and above the respective Debye temperatures. An excess thermal conductivity above that following from the T^? law is ascribed to an additional energy flux carried over by vacancies. The estimated activation energy Q_P for self-diffusion derived from the constant-volume values Q_V as determined from the temperature dependences of the “excess” thermal conductivities are in good agreement with the available data of direct diffusion measurements in solid Ar and Kr.     

Molecular dynamics study for the thermal conductivity of diatomic liquid

The thermal conductivity of diatomic liquids was analyzed using a nonequilibrium molecular dynamics (NEMD) method. Five liquids, namely, O₂, CO, CS₂, Cl₂ and Br₂, were assumed. The two-center Lennard-Jones (2CLJ) model was used to express the intermolecular potential acting on liquid molecules. First, the equation of state of each liquid was obtained using MD simulation, and the critical temperature, density and pressure of each liquid were determined. Heat conduction of each liquid at various liquid states [metastable (ρ=1.9ρ_cr), saturated (ρ=2.1ρ_cr), and stable (ρ=2.3ρ_cr)] at T=0.7T_cr was simulated and the thermal conductivity was estimated. These values were compared with experimental results and it was confirmed that the simulated results were consistent with the experimental data within 10%. Obtained thermal conductivities at saturated state were reduced by the critical temperature, density and mass of molecules and these values were compared with each other. It was found that the reduced thermal conductivity increased with the increase in the molecular elongation. Detailed analysis of the molecular contribution to the thermal conductivity revealed that the contribution of the heat flux caused by energy transport and by translational energy transfer to the thermal conductivity is independent of the molecular elongation while the contribution of the heat flux caused by rotational energy transfer to the thermal conductivity increases with the increase in the molecular elongation. Moreover, by comparing the reduced thermal conductivity at various states, it was found that the increase of thermal conductivity with the increase in the density, or pressure, was caused by the increase of the contribution of energy transfer due to molecular interaction.     

一种测量生物组织热导率的新方法

采用脉冲衰减法可以测量生物组织热导率。但是,Chen等人提出的脉冲衰减法采用了“点热源”假设,而实际测量时,探头有一定的几何尺寸,由此造成了测量时的模型误差。本文采用数值实验的方法对这一误差及其影响因素进行了分析。在此基础上,提出了一种考虑了探头尺寸影响的新的脉冲衰减法,推导出了其测量公式。采用已知热导率的工质进行了验证试验,实验测量结果证实了本文对原有测量方法误差的分析;同时也表明,采用本文提出方法可以将测量误差减小到5%以下。