热处理对非晶态合金Nd4Fe96-xBx磁性的影响

本文研究了用单辊急冷方法制备的非晶态合金Nd₄Fe_96-xB_x的晶化,以及热处理对其硬磁性和相组成的影响,发现非晶态合金Nd₄Fe_96-xB_x的晶化温度比相同B含量的非晶态合金Fe_100-xB_x高120—190K,X射线衍射和热磁测量表明,15≤x≤25的样品晶化相是由Nd₂Fe₁₄B(T 关键词：     

具有宽过冷液相区的Fe62Co8-x(Cr,Mo)xNb4Zr6B20非晶态合金的热稳定性与磁性

根据制备块状非晶态合金的三条经验准则,选择了成分为Fe₆₂Co_8-xCr_xNb₄Zr₆B₂₀和Fe₆₂Co_8-xMo_xNb₄Zr₆B₂₀(x=0,2,4)的合金系.利用单辊急冷法制备出厚为30μm宽为5mm左右的条带,并用差热分析、X射线衍射以及 关键词： 过冷液相区 铁磁性 非晶态合金     

Critical phenomena of amorphous Nd4(Fe0.75Cr0.25)77.5B18.5 alloys

The magnetic behavior of amorphous Nd₄(Fe_0.75Cr_0.25)_77.5B_18.5 alloys was investigated in the critical region. The Curie temperature T_C and critical exponents β, γ and δ are found to be 141 K, 0.45±0.02, 1.64±0.08 and 4.66±0.10, respectively. The data are fitted to a magnetic equation of state characteristic of a second-order phase transition over a rather wide range of temperatures both above and below T_C. It is noted that the values of the exponents are in disagreement with those derived for a three-dimensional Heisenberg ferromagnet and show an enhancement. This anomalous critical behavior may originate from magnetic inhomogeneity.     

Superconductivity magnetism and low temperature specific heat in YBa2(Cu1−xFex)3O7−δ with δ0 and δ1

Magnetic and low temperature specific heat measurements have been performed on iron doped YBa₂(Cu_1−xFe_x)₃O_7−δ samples with different oxygen contents (δ0 and δ1). Iron doping induces an orthorhombic to tetragonal transition and a decrease of both T_c and diamagnetic signal. Low temperature specific heat measurements reveal a Schottky type anomaly for δ0 samples with x=0.01 (1.8 K) and x=0.02 (3 K). This anomaly is attributed to magnetic interactions within iron limited chains. A numerical analysis of this effect is proposed.     

Effect of Co or Mn addition on the soft magnetic properties of amorphous Fe89−xZr11Bx (x=5, 10) alloy ribbons

The temperature and field dependent magnetic properties of melt-spun amorphous Fe_89−x−yZr₁₁B_x(Co,Mn)_y (x=5, 10 and 0≤y≤10) alloys in the temperature range 5-1200 K are reported. The Curie temperature and saturation magnetization at room temperature increase (decrease) almost linearly with Co (Mn) addition. With increasing Co concentration, the room temperature coercivity increases at the rate of 2.26 (0.28) A/m per at% for the x=5 (10) samples. The high-field magnetic susceptibility and local magnetic anisotropy decrease (increases) rapidly with increasing Co (Mn) concentration. The thermomagnetic curves show a marked increase in magnetization above 850 K corresponding to the crystallization of α-FeCo (α-Fe) phase in samples containing Co (Mn). The Curie temperature of the crystalline phase increases (remains same) with increasing Co (Mn) concentration with the formation of α-FeCo (α-Fe). Addition of Co up to 10 at% in Fe-Zr-B improves the room temperature saturation magnetization from 0.56 to 1.2 T, and Curie temperature from 315 to 476 K. Also, the coercivity increases with Co addition from 1.27 to 23.88 A/m for x=5 and from 7.64 to 10.35 A/m for x=10 alloy. The non-collinear spin structures that characterize Fe rich Fe-Zr-B amorphous alloys have been used to describe the observed results.     

The effect of thermal treatment on the magnetic properties of Ge-doped FeNbB alloys

The effects of Ge doping on the magnetic properties of nanocrystalline FeNbB ribbons are investigated. For amorphous Fe₈₀Nb₁₀Ge₃B₇ alloy, three crystallization processes are observed when heated from room temperature to 1173 K. At 973 K, a harder magnetic phase is formed, which brings about a constricted hysteresis loop. A large increase of relaxation frequency and a dramatic drop of permeability of 973 K-annealed Fe₈₀Nb₁₀Ge₃B₇ alloy are observed. The presence of Nb is essential for the nanocrystallization of α-Fe grains. If Nb is replaced by Ge completely, the thermal treatment will lead to the formation of coarse-grained Fe₃Ge phase rather than nanosized α-Fe grains. The coarse-grained Fe₃Ge results in a remarkable drop in magnetic softness. PACS 75.75.+a; 75.50.Bb     

A combined NMR and Mössbauer study of SRO in Fe80B20−x C x,amorphous alloys

The short range order (SRO) of amorphous Fe₈₀B_20?xC_x (X=0, 2, 4, 7, 9) alloys has been investigated by means of Mössbauer effect (ME) and nuclear magnetic resonance (NMR). Both the amorphous samples and the samples annealed at lower temperatures (693–713K) for a short time (10 minutes) were used. The Mössbauer measurement shows that the experimental spectra of annealed samples consist of the subspectra of α-Fe and bct-Fe₃B for X=0, While of α-Fe, bct-Fe₃B and o-Fe₃ (B, C) for X=2, 4, 7, 9. Moreover, the relative intensities of the subspectra originating from o-Fe₃ (B, C) increases with carbon concentration. These results are consistent with those of NMR very well.     

Mössbauer study of Fe-B alloys containing Nd additives

The influence of a few percent neodynium additives to Fe-B alloy on the hyperfine parameters was investigated. It was found that Nd decreases the hyperfine field of amorphous Fe-B alloys. The samples annealed at temperatures between 600°C and 700°C contain α-Fe and Fe₃B phases. The average hyperfine field of Fe₃B phase increases with increasing Nd content and decreases with increasing annealing temperature. The average isomer shift of Fe₃B phase decreases with increasing Nd content. The experimental data show that the change of hyperfine parameters of the Fe₃B phase in the studied alloys is due to Nd atom.     

The effect of different temperature annealing on phase relation of LaFe11.5Si1.5 and the magnetocaloric effects of La0.8Ce0.2Fe11.5−xCoxSi1.5 alloys

The phase relation of LaFe_11.5Si_1.5 alloys annealed at different high-temperature from 1223 K (5 h) to 1673 K (0.5 h) has been studied. The powder X-ray diffraction (XRD) patterns show that large amount of 1:13 phase begins to form in the matrix alloy consisting of α-Fe and LaFeSi phases when the annealing temperature is 1423 K. In the temperature range from 1423  to 1523 K, α-Fe and LaFeSi phases rapidly decrease to form 1:13 phase, and LaFeSi phase is rarely observed in the XRD pattern of LaFe_11.5Si_1.5 alloy annealed at 1523 K. With annealing temperature increasing from 1573  to 1673 K, the LaFeSi phase is detected again in the LaFe_11.5Si_1.5 alloy, and there is La₅Si₃ phase when the annealing temperature reaches 1673 K. There almost is no change in the XRD patterns of LaFe_11.5Si_1.5 alloys annealed at 1523 K for 3-5 h. According to this result, the La_0.8Ce_0.2Fe_11.5−xCo_xSi_1.5 (0≤×≤0.7) alloys are annealed at 1523 K (3 h). The analysis of XRD patterns shows that La_0.8Ce_0.2Fe_11.5xCo_xSi_1.5 alloys consist of the NaZn₁₃-type main phase and α-Fe impurity phase. With the increase of Co content from x=0 to 0.7, the Curie temperature T_C increases from 180 to 266 K. Because the increase of Co content can weaken the itinerant electron metamagnetic transition, the order of the magnetic transition at T_C changes from first to second-order between x=0.3 and 0.5. Although the magnetic entropy change decreases from 34.9 to 6.8 J/kg K with increasing Co concentration at a low magnetic field of 0-2 T, the thermal and magnetic hysteresis loss reduces remarkably, which is very important for the magnetic refrigerant near room temperature.     

Interface reactions in [Fe/B]<Subscript>n</Subscript> multilayers: a way to tune from crystalline/amorphous layer sequences to homogeneous amorphous Fe<Subscript>x</Subscript>B<Subscript>100-x</Subscript> films

[Fe/B]_{n ≥2} multilayers were prepared by thermal evaporation, ion-beam sputtering and laser ablation. By applying in situ electron spectroscopies (UPS, XPS) and monitoring the electrical resistance during layer growth, evidence could be provided for the occurrence of interface reactions within the range of studied deposition temperatures (77 K ≤T ≤300 K). These reactions result in amorphous Fe_xB_100-x phases, which are spatially restricted to a width of less than 3 nm at the original interface. The amorphicity of the reacted interlayers was unequivocally proven by additional high-resolution electron microscopy (HRTEM) and their characteristically changed magnetic properties. Due to the well-defined width of the interface reaction, homogeneous amorphous Fe_xB_100-x films can be obtained by reducing the individual Fe and B layer thicknesses to below the above reaction depth, while for larger thicknesses layer sequences of the crystalline/amorphous/crystalline type will result. Received: 30 January 2002 / Accepted: 31 January 2002 / Published online: 10 September 2002 RID="*" ID="*"Corresponding author. Fax: +49-731/502-2963, E-mail: hans-gerd.boyen@physik.uni-ulm.de     

Structure and magnetostriction of RFex (1.6 x 2.0) and R(Fe1−yTiy)1.8 (y 0.2) alloys (R=Dy0.65Tb0.25Pr0.1)

Structure, Curie temperature and magnetostriction of RFe_x (1.6 x 2.0) and R(Fe_1−yTi_y)_1.8 (y 0.2) alloys (R=Dy_0.65Tb_0.25Pr_0.1) have been investigated using optical microscopy, X-ray diffraction, AC initial susceptibility and standard strain gauge techniques. The homogenized RFe_x alloys are found to be essentially single phase in the range of 1.8 x 1.85. The second phase is a rare-earth-rich phase when x 1.8, and (Dy, Tb, Pr)Fe₃ phase when x 1.85. X-ray diffraction indicates that the R(Fe_1−yTi_y)_1.8 alloys contain a small amount of Fe₂Ti phase when y 0.05, which increases with the increment of Ti content. The Curie temperature of R(Fe₁−_yTi_y)_1.8 alloys slightly enhances with increasing Ti concentration when y 0.05, then remains almost unchanged in the range of 0.05 y 0.20. The magnetostriction of RFe_x alloys is improved when x 1.80 and reduced by increasing Fe content when x 1.85. The magnetostriction of R(Fe_1−yTi_y)_1.8 alloys is lowered by increasing Ti content.     

Synthesis and magnetic properties of Fe100-xMox alloy nanowire arrays

The Fe100-xMox(13≤x≤25) alloy nanowire arrays are synthesized by electrodeposition of Fe 2+ and Mo 2+ with different ionic ratios into the anodic aluminum oxide templates.The crystals of Fe100-xMox alloy nanowires gradually change from polycrystalline phase to amorphous phase with the increase of the Mo content and the nanowires are of amorphous structure when the Mo content reaches 25 at%,which are revealed by the X-ray diffraction and the selected area electron diffraction patterns.As the Mo content increases,the magnetic hysteresis loops of Fe100-xMox alloy nanowires in parallel to the nanowire axis are not rectangular and the slopes of magnetic hysteresis loops increase.Those results indicate that the magnetostatic interactions between nanowires and the magnetocrystalline anisotropy both have significant influences on the magnetization reversal process of the nanowire arrays.     

Relation between structure and magnetism of TixFe100−x alloys within the C14 Laves-phase stability range

We report about X-ray and magnetic investigations on polycrystalline alloys with hexagonal C14 (MgZn₂) structure of the system Ti_xFe_100−x in the concentration range 30.5x36.5 around the Laves-phase composition TiFe₂ (Ti_33.3Fe_66.6). Neighboring compositions Fe₅₀Ti₅₀ (with B2 structure) and Ti₁₅Fe₈₅ and Ti₂₀Fe₈₀ (with BCC structure) have also been investigated. From the data we establish a magnetic phase diagram for the C14 range of the system, showing a rather sharp transition from mainly ferromagnetic ordering in the range x<32 to a mainly antiferromagnetic ordering in the range x>32. The results can be made plausible microscopically by taking the site dependence of the moments into account. A revised structural equilibrium phase diagram is also given.     

Magnetische untersuchungen an mischkristallen der quasibinären legierungssysteme (Cd Te)1-x (Mn Te)x und (Sn Te)1-x (Mn Te)x

The magnetic susceptibility and magnetization are presented for polycrystalline samples of the alloy systems Cd_1-xMn_xTe 0 < x 0.1 and Sn_1-xMn_xTe 0 < 4 0.4. The magnetic measurements were performed between 2.3 K and 300 K in external magnetic fields up to 11 kOe. At sufficiently high temperatures the susceptibility can be described by a Curie-Weiss law. In the system Sn_1-xMn_xTe θ_p is positive. A linear dependence θ_p ∞ x was found with θ_p(0.4) = 49 K. In the series Cd_1-xMn_xTe θ_p changes sign. For θ < x < 0.04 θ_p is positive with a maximum θ_p ≈ 10 K at x = 0.02. In the region x #62; 0.04 θ_p becomes negative with θ_p = -35 K at x = 0.1. The effective spin value of manganese is S_eff #62; 5/2 for all the samples. The investigation was done to check the assumption that ferromagnetic coupling may exist in tellurides of manganese if the shortest distance d_MnMn is greater than 3.4 Å. This hypothesis has been stated. In the case θ_p #62; 0 the results are partly explained by the RKKY exchange coupling.     

Crystallisation kinetics of amorphous Fe72.5−xCu1Nb4.5Si10+x+y B12-y alloy

Fe_73.5Cu₁Nb₃Si_13.5B₉ and Fe_72.5–xCu₁Nb_4.5Si_10+x+y B_12–y alloys are compared from the point of view of crystallisation behaviour and changes in the short-range order in the amorphous reminder. The increase in Nb to 4.5 at.% in the latter system slows down the formation of nanocrystals to approximately 40% even after 16 hours of anneal at 550 °C forx=0.5,y=3. Segregation-induced changes in the short-range order are manifested via hyperfine field distributions corresponding to the amorphous reminder.     

Crystallization and magnetic properties of melt-spun neodymium-iron alloys

The magnetic and crystallization properties of melt-spun Nd_1?xFe_x alloys are reported. By using high purity constituents and an extremely fine orifice (100–150 μm), amorphous alloys were prepared over the interval 0.4 ? x ? 0.8. Their magnetic properties, taken between 20–850 K in fields up to 95 kOe, are interpreted on the basis of a sperimagnetic structure; at high field the alloys from collinear ferromagnetic structures. Room temperature coercivities of the amorphous alloys are relatively low (1.5–2.0 kOe) but increase substantially at reduced temperatures; at 20 K, a maximum coercivity of 52 kOe was found for a Nd_0.4Fe_0.6 alloy. X-ray diffraction indicates that the melt-spun alloys crystallize by the precipitation of Nd metal and an unidentified Nd-Fe phase. Changes in magnetization and coercivity during crystallization are reported.     

Dispersive optical constants of a-Se100−xSbx films

Thin films of amorphous Se_100−xSb_x (x=5,10 and 20 at%) system are deposited on a silicon substrate at room temperature (300 K) by thermal evaporation technique. The optical constant such as refractive index (n) has been determined by a method based on the envelope curves of the optical transmission spectrum at normal incidence by a Swanpoel method. The oscillator energy (E_o), dispersion energy (E_d) and other parameters have been determined by the Wemple–DiDomenico method. The absorption coefficient (α) has been determined from the reflectivity and transmitivity spectrum in the range 300–2500 nm. The optical-absorption data indicate that the absorption mechanism is a non-direct transition. We found that the optical band gap, E_g^opt, decreases from 1.66±0.01 to 1.35±0.01 eV with increase Sb content.     

Die magnetische struktur der NiAs-phase des systems (Cr1-xFex)1+Sb im bereich positiver austauschkopplung

A linear dependence of the reciprocal susceptibility on the temperature similar to a Curie-Weiss-law with positive values of the paramagnetic Curie temperature θ_p was found for the (Cr_1-xFe_x)₁₊Sb ternary system in an intermediate range of x between the antiferromagnetic end members (x = 0 and 1). A magnetization appears below θ_p with temperature and external field dependences, for fields below a critical applied field, which are unusual for ferromagnetic substances. A remanence is found only far below θ_p. In this temperature range the magnetization depends on the time elapsed after changing the applied field and on the magnetic as well as on the thermal history. These phenomena are investigated and an interpretation of the observed behavior is discussed using the model of the magnetic structure for mictomagnets.     

Structural and vibrational properties of dilute GaNxAs1−x(P1−x)

We report a comprehensive analyzes of the Fourier transform infrared (FTIR) absorption and Raman scattering data on the structural and vibrational properties of dilute ternary GaAs_1−xN_x,[GaP_1−xN_x] (x<0.03) alloys grown on GaAs [GaP] by metal organic chemical vapor deposition (MOCVD) and solid source molecular beam epitaxy (MBE). By using realistic total energy and lattice dynamical calculations, the origin of experimentally observed N-induced vibrational features are characterized. Useful information is obtained about the structural stability, vibrational frequencies, lattice relaxations and compositional disorder in GaNAs (GaNP) alloys. At lower composition (x<0.015) most of the N atoms occupy the As [P] sublattice {N_As[N_P]}—they prefer moving out of their substitutional sites to more energetically favorable locations at higher x. Our results for the N-isotopic shifts of local mode frequencies compare favorably well with the existing FTIR data.     

Mössbauer spectroscopy studies of spin reorientations in amorphous and crystalline (Co0.2Fe0.8)72.5Si12.5B15 glass coated micro-wires

Thermo-gravimetric, differential scanning calorimetry and comprehensive ⁵⁷Fe Mössbauer spectroscopy studies of amorphous and crystalline ferromagnetic glass coated (Co_0.2Fe_0.8)_72.5Si_12.5B₁₅ micro-wires have been recorded. The Curie temperature of the amorphous phase is T_C(amorp) ∼730 K. The analysis of the Mössbauer spectra reveals that below 623 K the easy axis of the magnetization is axial-along the wires, and that a tangential or/and radial orientation occurs at higher temperatures. At 770 K, in the first 4 hours the Mössbauer spectrum exhibits a pure paramagnetic doublet. Crystallization and decomposition to predominantly α-Fe(Si) and Fe₂B occurs either by raising the temperature above 835 K or isothermally in time at lower temperatures. Annealing for a day at 770 K, leads to crystallization. In the crystalline material the magnetic moments have a complete random orientation. After cooling back to ambient temperature, both α-Fe(Si) and Fe₂B in the glass coated wire show pure axial magnetic orientation like in the original amorphous state. The observed spin reorientations are associated with changes in the stress induced by the glass coating.