气相色谱-氮化学发光检测法分析催化汽油中含氮化合物类型的分布

建立了催化汽油馏分中各种含氮化合物类型分布的气相色谱-氮化学发光检测分析方法,考察了各种色谱条件对含氮化合物分离的影响。采用化学预处理的方法浓缩了催化汽油中的含氮化合物,并结合气相色谱-质谱检测以及部分含氮化合物标准样品,对某催化汽油中的20多个含氮化合物进行了定性(或归类)。催化汽油中几种主要含氮化合物(苯胺、2-甲基苯胺、二甲基苯胺)含量测定值的相对标准偏差(RSD)均不大于2.5%。当信噪比(S/N)为3时,苯胺氮的检出限为1.0 mg/L。该方法可用于不同来源和不同加工工艺的汽油馏分中各种含氮化合物类型分布的研究。     

直接进样-液相色谱-串联质谱法同时测定水中的5种苯胺类化合物

建立了直接进样测定生活饮用水及其水源水中5种苯胺类化合物(苯胺、3-硝基苯胺、4-硝基苯胺、2,6-二氯-4-硝基苯胺和六硝基二苯胺)的液相色谱-串联质谱法。水样经0.22μm 聚醚砜滤膜过滤后直接进样,目标化合物在 HSS T3色谱柱上经梯度洗脱,于4 min 完成分离,多反应监测模式检测。5种苯胺类化合物在各自线性范围内线性良好,相关系数 R≥0.995。方法的检出限为0.773~1.88μg/ L(S/ N =3),定量限为2.58~6.27μg/ L(S/ N=10);峰面积的日内和日间相对标准偏差(RSD)分别为0.8%~1.9%和3.3%~4.9%;样品加标回收率为84.1%~105.0%,加标样品的 RSD 为1.0%~3.1%。应用本方法对35份水样进行了分析。结果表明,本方法准确、灵敏、快速,适用于生活饮用水及其水源水的常规分析,可为苯胺类化合物的污染评价提供技术支持。     

乳胶制品中N-亚硝胺析出物的GC-MS/SIM检测

使用气相色谱-质谱(GC-MS/SIM)检测了乳胶制品中5种N-亚硝胺析出物,样品经过二氯甲烷萃取,用Rtx-5MS石英毛细管柱分离,采用内标法进行检测计算.实验得出5种N-亚硝基化合物的内标标准曲线日内RSD(小于5%),日间RSD(小于14%).N-亚硝基二乙胺(NDEA)、N-亚硝基二丙胺(NDPA)、N-亚硝基哌啶(NPIP)、N-亚硝基二丁胺(NDBA)、N-亚硝基二苯胺(NDPhA)的方法的检出限分别为2.0,5.0,10.0,1.0,112.0μg/L.运用该法对北京市场的乳胶制品进行了检测.     

三苯胺类小分子的合成及其AIE性能研究

以二苯胺、碘苯、对碘甲苯以及对碘苯甲醚为原料,合成了三苯胺及其衍生物T1~T5(4-甲氧基三苯胺、4-甲基三苯胺、4-醛基三苯胺、4-乙烯基三苯胺),并对其紫外-可见吸收光谱与荧光光谱进行了检测。结果表明,连有甲氧基、甲基、乙烯基取代基的三苯胺化合物在甲醇/氯仿混合溶液中具有聚集诱导发光(AIE)性能;而醛基取代的4-醛基三苯胺表现出了聚集荧光猝灭(ACQ)现象。     

固相微萃取/气相色谱-质谱联用法测定橡胶密封材料中N-亚硝胺

建立了固相微萃取/气相色谱-质谱联用法(SPME/GC-MS)测定橡胶密封材料中N-亚硝基-N-甲基苯胺(NMPh A)、N-亚硝基-N-乙基苯胺(NEPh A)和N-亚硝基二苯基胺(NDPhe A)3种N-亚硝胺化合物含量的方法。样品参考国标GB/T 24153-2009进行预处理后,采用固相微萃取进行提取,对影响固相微萃取效率的纤维涂覆种类、萃取时间、搅拌速度和萃取温度等条件进行优化。在优化条件下,方法的线性范围为5~500μg/L,相关系数(r)均大于0.99,检出限为0.5μg/kg,回收率为77%~92%,相对标准偏差(RSD,n=6)为3.8%~7.7%。     

萃取分离-离子色谱法测定间羟基-N,N-二乙基苯胺中的无机阴离子

建立了检测常用化工原料间羟基-N,N-二乙基苯胺中无机阴离子(F-、Cl-、NO3-和SO42-)含量的萃取分离-离子色谱分析方法。方法以甲苯为溶剂溶解间羟基-N,N-二乙基苯胺,用水相萃取分离得到其中的无机阴离子F-、Cl-、NO3-和SO42-等;色谱柱采用Metrosep A supp 5型阴离子分离柱,流动相为3.2 mmol/L Na2CO3与1.0 mmol/L NaHCO3的混合液,流速0.7 mL/min。结果表明:F-、Cl-、NO3-和SO42-的线性关系分别为y=1.2036x 1.0703(r=0.9999)、y=1.3999x-0.2531(r=0.9999)、y=2.6612x-0.9482(r=1.0000)、y=1.9337x 0.0719(r=0.9999);平均回收率分别为F-101.6%(RSD 5.92%),Cl-107.6%(RSD 4.82%),NO3-106.9%(RSD 3.08%),SO42-95.17%(RSD 3.32%);检出限分别为:F-0.003 mg/L、Cl-0.005 mg/L、NO3-0.016 mg/L和SO42-0.010 mg/L。该方法简便、快速、灵敏度高,具有较强的实用价值。     

含有三苯胺环类席夫碱的合成

以4,4’-二甲酰基三苯胺为原料,通过Wittig和胺醛缩合反应合成了两个含有三苯胺环席夫碱类化合物——4-(对甲基苯乙烯基)-4’-亚(α-萘胺)甲基三苯胺和4-(对甲基苯乙烯基)-4’-亚(2-氨基芴)甲基三苯胺,其结构经1H NMR,13CNMR和IR确证。     

含吗啉基片段的水杨醛席夫碱类化合物的合成及其淬灭1,1-二苯基-2-三硝基苯肼自由基性能

通过3-氟-4-吗啉基苯胺和取代水杨醛缩合反应,合成了14个含吗啉基片段水杨醛席夫碱类化合物(Ⅰa-Ⅰn)。通过核磁共振波谱仪(NMR)、傅里叶变换红外光谱仪(FTIR)、液相色谱-质谱联用仪(LC-MS)和元素分析等技术手段研究了产物的结构和淬灭1,1-二苯基-2-三硝基苯肼(DPPH)自由基的活性。 结果表明,在0.02~0.10 g/L,所有化合物均表现出一定的淬灭DPPH自由基活性。 其中,化合物Ⅰd和Ⅰf表现出较为优异的性能,化合物Ⅰd的活性在30%~55%,化合物Ⅰf的活性则大于50%。 随着化合物Ⅰd、Ⅰh、Ⅰj和Ⅰn质量浓度的增大,其淬灭DPPH自由基的活性均呈现增强趋势。     

超高效液相色谱-串联质谱法测定动物源性食品中10种水杨酰胺类化合物

建立了动物源性食品中10种水杨酰胺类化合物(5-氯水杨酰苯胺、4'-溴水杨酰苯胺、3',4'-二氯水杨酰苯胺、4',5-二氯水杨酰苯胺、3',4',5-三氯水杨酰苯胺、5-溴-4'-氯水杨酰苯胺、3,5-二溴水杨酰苯胺、4',5-二溴水杨酰苯胺、3,4',5-三溴水杨酰苯胺、3,3',4',5-四氯水杨酰苯胺)的超高效液相色谱-串联质谱(UPLC-MS/MS)检测方法。样品经乙腈萃取,氨基固相萃取小柱(SPE)净化,T3色谱柱分离后,以甲醇-0.1%甲酸溶液梯度洗脱,串联质谱电喷雾负模式扫描,多反应监测模式检测,外标法定量。结果表明,10种目标物在一定范围内线性关系良好,相关系数(r~2)不小于0.995 7,检出限为0.5~1.0μg/kg,定量下限为1.5~3.0μg/kg;加标水平为1.5~30.0μg/kg时,回收率为81.0%~106%,相对标准偏差(RSD,n=6)不大于7.5%。该方法净化效果好、定量准确、灵敏快速,适用于动物源性食品中10种水杨酰胺类化合物的检测与确证。     

微波促进合成苝单酰亚胺类化合物

以3,4;9,10-苝四甲酸酐为原料,经微波促进反应探讨了反应底物用量、反应时间和反应温度等条件对反应收率的影响,合成了系列苝单酰亚胺类化合物,其中2,6-二异丙基苯胺修饰的苝单酰亚胺化合物N-2’,6’-二异丙基苯胺基-3,4-苝单酰亚胺(PMI-1)在30min的反应时间内,分离收率可达64.1%.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.