开口裂纹梁振动特性参数分析

开展仿真分析探究梁边界条件、裂纹位置、裂纹程度、梁几何尺寸对开口裂纹矩形梁振动特性的影响．采用等效刚度模型建立裂纹梁结构振动方程,并与试验比较完成验证．预报梁在简支、悬臂、固支三种边界下,在不同位置发生不同程度裂纹损伤时的固有频率．研究发现,裂纹梁固有频率特性与完好无损梁曲率模态相关．裂纹可使固有频率降低,且降低程度随损伤程度增加而愈显著．裂纹位置接近完好梁某阶曲率模态零点（无效位置）/极点时,该阶固有频率受到影响将会减弱/增强．开展悬臂裂纹梁在不同几何尺寸下曲率模态分析．研究发现,曲率模态在裂纹处发生尖角突变现象,且尖角峰值随着损伤程度的增加而增大．裂纹位置接近某阶曲率模态极点/零点时,该阶模态受裂纹影响更显著/不明显．在裂纹相对位置和损伤程度相同时,增加梁长度使裂纹处尖角峰值减小,改变梁宽度不影响曲率模态,增加梁高度可使尖角峰值增加．研究成果可为试验提供基础,为扩建数据库,探索一种在线检测方法,基于实时大数据和人工智能技术开展各项振动参数综合分析,为实现梁裂纹智能识别与定位提供依据．     

基于裂纹附加模态Timoshenko梁的裂纹损伤识别

将梁中横向裂纹等效为无质量扭转弹簧，并忽略其对梁剪切变形的影响，得到的具有任意裂纹数目Timoshenko 梁自振模态的统一显示解析表达式．将裂纹梁的自振模态分为基本模态和裂纹附加模态，利用最小二乘拟合，建立了利用裂纹附加模态函数的梁裂纹损伤识别方法．通过数值模拟开展了简支单裂纹梁以及悬臂和固支双裂纹梁等的裂纹损伤识别，考察了测量误差对损伤识别的影响，数值结果表明本文所提出的裂纹损伤识别方法对裂纹位置的识别精度高于对裂纹损伤程度的识别精度；随着测量误差的增加，裂纹位置及裂纹损伤程度的识别误差增加，但仍在可接受的范围内，故该裂纹损伤识别方法在实际工程中具有一定的应用价值．     

基于裂纹诱导弦挠度的简支外伸梁裂纹损伤识别

基于梁横向开裂纹的线性扭转弹簧模型,给出了具有任意裂纹数目的简支外伸梁弯曲挠度的显式解析解,研究了集中载荷作用下简支外伸梁裂纹诱导弦挠度函数的性质,给出了裂纹位置和裂纹等效扭转弹簧柔度的近似表达式,从而实现了梁横向裂纹位置及裂纹损伤程度的识别．在此基础上,为利用裂纹梁的测量挠度识别裂纹损伤,提出了分段线性函数的最佳拟合法,实现了简支外伸梁裂纹的损伤参数识别．通过数值试验验证了该识别方法的适用性和可靠性,考察了识别结果对梁挠度测量误差和裂纹深度的敏感性,结果表明随着挠度测量误差的增大,裂纹损伤参数识别误差增大,但裂纹损伤识别方法具有较强的鲁棒性,在工程实际中具有一定的应用性．     

含裂纹一维欧拉梁的裂纹无效位置分析

基于集中柔度模型,建立了含裂纹一维欧拉梁的频率方程,以此为基础探讨了裂纹无效位置的求解方法。数值计算结果显示,裂纹无效位置和位移振型节点并不一致。进一步的理论推导证明裂纹无效位置就是曲率模态振型的零点位置,从曲率和力学性能基本参数的关系分析,这一结论是合理的。本文结论对于实验、测试方案设计有指导意义。     

基于裂纹诱导弦挠度的梁开闭裂纹损伤识别

考虑裂纹缝隙效应,建立了Euler-Bernoulli梁中开闭裂纹位置、深度和初始张开角等损伤参数的识别方法．首先,基于梁中开闭裂纹的等效单向扭转弹簧模型,给出了开闭裂纹Euler-Bernoulli梁静力弯曲挠度的显式闭合解．在此基础上,证明了裂纹诱导弦挠度函数由分段三次多项式组成,并基于其构造特征,建立了基于测量挠度的梁中开闭裂纹位置、裂纹等效扭转弹簧柔度、裂纹初始张开角和裂纹上下侧属性等参数的数值识别方法．最后,通过数值实验考察了挠度测量误差和裂纹位置等对裂纹识别结果的影响,结果表明：裂纹位置、裂纹等效扭转弹簧柔度和裂纹初始张开角等的识别误差随挠度测量误差增大而增大,但裂纹识别结果具有较强的鲁棒性,在工程实际中具有一定的应用前景．     

含多处裂纹梁的振动分析

基于传递矩阵方法,提出了一种计算含有任意处裂纹梁固有频率的新方法。将梁内裂纹模拟为无质量的弯曲弹簧,得到了梁的解析特征方程。通过数值模拟计算,讨论了裂纹数量,以及裂纹位置和裂纹深度对梁的固有频率的影响。通过与文献[4]的计算结果比较,验证了本文方法的有效性。     

Pasternak双参数地基上Euler-Bernoulli裂纹梁弯曲的解析解

基于开裂纹的等效扭转弹簧模型,采用Laplace变换,给出了Pasternak地基上具有任意裂纹数目的Euler-Bernoulli梁弯曲变形的解析通解.在验证本文解析解正确的基础上,数值分析了Pasternak地基上简支裂纹梁的弯曲变形和内力特征,考察了裂纹数目、深度、位置以及地基反力系数对裂纹梁弯曲的影响.结果表明:在裂纹处梁挠度分布存在尖点,而转角分布存在跳跃,并且尖点效应和转角跳跃随着裂纹深度的增加而愈加明显;同时随着地基反力系数的增大,裂纹梁的挠度、弯矩和转角逐渐减小;此外,随着地基反力系数的增大,裂纹数目对裂纹梁挠度的影响逐渐减弱.这些结果为Pasternak地基上梁的裂纹损伤识别提供了理论基础.     

含初缺陷裂纹损伤梁的冲击动力屈曲

由Hamilton原理导出考虑初始缺陷及横向剪切变形时裂纹梁的动力屈曲控制方程;应用断裂力学中常用的线弹簧模型将裂纹引入到屈曲控制方程中;基于B-R动力屈曲判断准则,采用数值方法求解了受轴向冲击载荷作用时裂纹梁的动力屈曲;对比讨论了不同冲击速度、初始几何缺陷大小以及分布形式等因素对梁冲击动力屈曲的影响。     

含旋转运动效应裂纹梁横向振动特性的研究

针对开口裂纹作用下旋转运动欧拉-伯努力梁的振动特性进行了研究。文中使用裂纹梁连续等效刚度模型模拟裂纹效应,将含裂纹旋转运动梁视为弯曲刚度沿梁长度方向连续变化的梁,并应用传递矩阵法推导了求解其振动特性的特征方程。考虑不同裂纹深度和位置、不同旋转速度,分析了梁的一阶和二阶固有频率的变化情况。研究结果表明:旋转运动效应和裂纹效应并非独立影响梁的固有频率,两者间具有耦合作用效应;转速提升使由裂纹导致的频率衰减幅度变小,同时裂纹加深使得由速度升高带来的阶频提升更加显著;相比于二阶频率,耦合作用效应对于一阶频率更加显著。     

含双裂纹圆截面悬臂梁的损伤识别研究

裂纹的萌生和扩展直接影响构件的振动响应,对构件的安全可靠性具有重要影响.本文以圆截面悬臂梁为对象,结合转角模态振型和模态频率等高线,研究了一种双裂纹识别技术.首先,基于应力强度因子和卡氏定理推导了无裂纹梁单元和含裂纹梁单元的刚度矩阵;在此基础上,建立了含裂纹圆截面悬臂梁的有限元动力学方程;然后,结合裂纹对梁转角模态振型和模态频率的影响,提出了双裂纹识别策略.最后,通过算例讨论了双裂纹识别策略的可行性.结果表明,圆截面悬臂梁的模态转角在裂纹位置出现突变,裂纹深度越大转角突变值越大;将识别出的裂纹位置作为已知参数,通过模态频率等高线法,可以准确地识别出双裂纹的深度.     

An approximate method of response analysis of vibrations for cracked beams

I.IntroductionTheinvestigationsonthed}'nan1icresponsesofcrackedbeamshavebeendonebymanyresearchers.Howeter,upti11now.totheauthors-knot"ledge,intheirwork,thereha\-ebeenmanypapersaboutnumericaln1ethodstobeusedasamainmeanstostudy,whileveryfewpapersab0utanalyt…     

Three-Dimensional Dynamic Contact Problem for an Elliptic Crack Interacting with a Normally Incident Harmonic Compression–Expansion Wave

The paper deals with the three-dimensional dynamic problem for an elliptic crack interacting with a normally incident harmonic compression–expansion wave, considering the contact interaction of the crack faces. An asymmetric solution is obtained using an iteration algorithm developed earlier. Numerical results are presented     

基于压电导率特性识别结构裂纹方法的研究

基于粘贴于外部主体裂纹在压电陶瓷片导率的变化,实验提取出梁系统的变民模态频率。建立了考虑压电陶瓷片影响的裂纹梁的特性方程,根据裂纹梁的固有频率的变化,采用剪切弹簧模拟裂纹的方法,进行了裂纹的识别,结果表明满足一定的识别精度。     

On the Determination of Nonlinear Response Distributions for Oscillators with Combined Harmonic and Random Excitation

The analysis of two different nonlinear systems, both subject to an excitation that comprises a harmonic and a random component, is presented in this paper. Both systems are known to exhibit different coexisting attractors for a purely harmonic forcing. The random part causes a disturbance of the response of these systems: Even though a dominating effect of the attractors for the deterministic case is still visible, the random disturbance also leads to occasional jumps between the areas surrounding the different attractors. To access the likelihood of the system being found in a specific state, probability density functions are approximated numerically by means of a localized statistical linearization.     

DYNAMIC BEHAVIOR OF TWO PARALLEL SYMMETRY CRACKS IN MAGNETO-ELECTRO-ELASTIC COMPOSITES UNDER HARMONIC ANTI-PLANE WAVES

The dynamic behavior of two parallel symmetry cracks in magneto-electro-elastic composites under harmonic anti-plane shear waves is studied by Schmidt method. By using the Fourier transform, the problem can be solved with a pair of dual integral equations in which the unknown variable is the jumps of the displacements across the crack surfaces. To solve the dual integral equations, the jumps of the displacements across the crack surface were expanded in a series of Jacobi polynomials. The relations among the electric filed, the magnetic flux and the stress field were obtained. From the results, it can be obtained that the singular stresses in piezoelectric/piezomagnetic materials carry the same forms as those in a general elastic material for the dynamic anti-plane shear fracture problem. The shielding effect of two parallel cracks was also discussed.     

Parametric excitation of beams moving over supports

Studied in this work are the formulation of equations of motion and the response to parametric excitation of a uniform cantilever beam moving longitudinally over a single bilateral support. The equations of motion are generated by using assumed modes to discretize the beam, by regarding the support as a kinematic constraint, and by employing an alternate form of Kane's method that is particularly well suited to systems subject to constraints. Instability information is developed using the results of perturbation analysis for harmonic longitudinal motions of small amplitude and with Floquet theory for general periodic motions of any amplitude. Results demonstrate that definitive instability information can be obtained for a beam moving longitudinally over supports based on the frequencies of free transverse vibration of a beam that is longitudinally fixed.     

Wave propagation through a periodic array of inclined cracks

In the frame of wave propagation in damaged (elastic) solids, an analytical approach for normal penetration of a plane wave through a periodic array of inclined cracks is developed. The problem is reduced to an integral equation holding over the length of each crack; approximated forms (of one-mode and low-frequency types) are then given to the kernel, so as to derive explicit formulas for the reflection and transmission coefficients. Numerical resolution of the relevant equations finally provides some graphs that are compared.     

Static analysis of Euler–Bernoulli beams with multiple unilateral cracks under combined axial and transverse loads

The paper deals with the static analysis of pre-damaged Euler–Bernoulli beams with any number of unilateral cracks and subjected to tensile or compression forces combined with arbitrary transverse loads. The mathematical representation of cracks with a bilateral behaviour (i.e. always open) via Dirac delta functions is extended by introducing a convenient switching variable, which allows each crack to be open or closed depending on the sign of the axial strain at the crack centre. The proposed model leads to analytical solutions, which depend on four integration constants (to be computed by enforcing the boundary conditions) along with the Boolean switching variables associated with the cracks (whose role is to turn on and off the additional flexibility due to the presence of the cracks). An efficient computational procedure is also presented and numerically validated. For this purpose, the proposed approach is applied to two pre-damaged beams, with different damage and loading conditions, and the results so obtained are compared against those given by a standard finite element code (in which the correct opening of the cracks is pre-assigned), always showing a perfect agreement.     

Anomalies associated with energy release parameters for cracks in piezoelectric materials

For a central crack in a piezoelectric plate, the mode-I stress intensity factor (K_I), electric displacement intensity factor (K_D), energy release rates (G, G_M) and energy density factor (S) are obtained from the finite element results. For the impermeable crack, the numerical results of K_I and K_D are coupled; this error is contrary to the uncoupled analytical solutions. The error has little effect on the total energy release rate G and energy density factor S, but in some cases, large errors in the mechanical energy release rate G_M are observed. G is global while SED is local. Also G is negative which defies physics where energy cannot be created while crack attempts to extend as implied by G. Computations should be made for the J-integral and also show that J becomes negative. What this shows is that the global fracture energy criterion is not suitable to address the local release of energy because it includes the overall energy which are irrelevant to fracture initiation being a local behavior. In addition, the case study shows that the energy density theory is the better fracture criterion for the piezoelectric material. According to the results of S, it retards the crack growth when the external electric field and piezoelectric poling are on opposite directions. This conclusion agrees with analytical and experimental evidence in the past references.     

FREE VIBRATION ANALYSIS OF SIMPLY SUPPORTED BEAM WITH BREATHING CRACK USING PERTURBATION METHOD

In this paper, a new analytical method for vibration analysis of a cracked simply supported beam is investigated. By considering a nonlinear model for the fatigue crack, the governing equation of motion of the cracked beam is solved using perturbation method. The solution of the governing equation reveals the superhaxmonics of the fundamental frequency due to the nonlinear effects in the dynamic response of the cracked beam. Furthermore, considering such a solution, an explicit expression is also derived for the system damping changes due to the changes in the crack parameters, geometric dimensions and mechanical properties of the cracked beam. The results show that an increase in the crack severity and approaching the crack location to the middle of the beam increase the system damping. In order to validate the results, changes in the fundamental frequency ratios against the fatigue crack severities are compared with those of experimental results available in the literature. Also, a comparison is made between the free response of the cracked beam with a given crack depth and location obtained by the proposed analytical solution and that of the numerical method. The results of the proposed method agree with the experimental and numerical results.