共查询到18条相似文献,搜索用时 415 毫秒
1.
为了提高砷化镓(GaAs)多结太阳电池的光电转换效率,设计了宽光谱(300 nm~1 800 nm)ZnS/Al2O3/MgF2三层减反射膜,分析了各层的厚度及折射率对三层膜系有效反射率的影响。结果表明: 对于整个波长,ZnS厚度对有效反射率的影响要大于Al2O3和MgF2,MgF2厚度对有效反射率的影响最小;适当减小MgF2的折射率或增加ZnS的折射率可得到更低的有效反射率。同时,当 ZnS,Al2O3和MgF2的最优物理厚度分别为52.77 nm,82.61 nm,125.17 nm时,此时最小有效反射率为2.31%。 相似文献
2.
a-Si/SiO2多量子阱材料制备及其晶化和发光 总被引:3,自引:0,他引:3
本文研究用等离子体增强化学气相淀积(PECVD)方法淀积SiO2和非晶硅(a-Si)时淀积速率和薄膜折射率与淀积条件的关系。选择合适的淀积条件制备了a-Si/SiO2多量子阱结构材料。用激光扫描退火方法使其晶化,当a-Si和SiO2层厚度分别为4nm和6nm时,形成了颗粒大小为3.8nm的硅晶粒。晶化后的样品在10K下可以观察到较强的光荧光发射,三个峰值波长分别为810、825和845nm. 相似文献
3.
本文采用火焰水解法(FHD)在单晶Si片上快速淀积SiO2/SiO2-GcO2厚膜,再经过高温玻璃化处理,获得了玻璃态的平面波导材料。下包层SiO2膜的厚度约为40μm,波长1550nm处的折射率为1.4462,芯层SiO2-GeO2膜的厚度为5μm,折射率为1.4631。分别采用XRD、XPS、SEM和椭偏仪等对波导材料表面特性和折射率等进行了测试分析。 相似文献
4.
5.
6.
7.
采用矢量法设计了三硼酸锂(LiB3O5,LBO)晶体上1 064 nm、532 nm、355 nm和266 nm四倍频增透膜.结果表明,在1 064 nm、532 nm、355 nm和266 nm波长的剩余反射率分别为0.001 9%、0.003 1%、0.006 1%和0.004 7%.根据容差分析,薄膜制备时沉积速率准确度控制在+6.5%时,基频、二倍频、三倍频和四倍频波长的剩余反射率分别增加至0.24%、0.92%、2.38%和4.37%.当薄膜材料折射率的变化控制在+3%时,1 064 nm波长的剩余反射率增大为0.18%,532 nm、355 nm和266 nm波长分别达0.61%,0.59%,0.20%.与薄膜物理厚度相比,膜层折射率对剩余反射率的影响大.对膜系敏感层的分析表明,在1 064 nm和266 nm波长,从入射介质向基底过渡的第二层膜厚度变化对剩余反射率的影响最大,其次是第一膜层.在532 nm和355 nm波长,从入射介质向基底过渡的第一和第四膜层是该膜系的敏感层.误差分析也表明,薄膜材料的色散对特定波长的剩余反射率具有明显影响,即1 064 nm、532 nm、355 nm和266 nm波长的剩余反射率分别增加至0.30%、0.23%、0.58%和3.13%. 相似文献
8.
用电子束蒸发沉积方法在X切LBO(X-LBO)晶体上镀制了两种不同膜系结构的1 064和532 nm倍频增透膜,其中一种膜系结构为基底/ZrO2/Y2O3/Al2O3/SiO2/空气,另一种为基底/0.5Al2O3/ZrO2/Y2O3/Al2O3/SiO2/空气,两种膜系结构的主要差别在于有无氧化铝过渡层。测量了薄膜的反射率光谱曲线,发现两种增透膜在1 064和532 nm处的反射率均小于0.5%,实际镀制结果与理论设计曲线的差异主要是由材料折射率的变化引起的。且对样品在空气环境中进行了温度为473 K的退火处理,结果发现两种膜系结构均表现了较优异的光学性能,氧化铝过渡层的加入使薄膜具有强的热应力性能。 相似文献
9.
超宽带减反射膜的设计和制备 总被引:3,自引:0,他引:3
设计了400~900 nm波段上的超宽带减反射膜,在410~850 nm范围内的平均残余反射率设计值约为0.2%,在设计的全波段上约为0.24%.讨论了初始膜系结构的选择原则,分析了带宽、膜层折射率差、最外层折射率和膜层总厚度等因素对宽带减反射特性的影响.对特定的带宽.增加两种薄膜材料的折射率差和选择尽可能低的最外层折射率对获得优良的减反射特性是非常重要的.实验制备了K9玻璃上TiO2/MgF2两种材料组成的8层结构的超宽带减反射膜,实测结果表明,在带宽520 nm范围内的平均残余反射率约为0.44%,说明用二种材料设计超宽带减反射膜是成功的,对垂直入射的减反射膜.多种材料的膜系并不比两种材料更具优越性. 相似文献
10.
本文叙述在Ge基底上镀制对8-11.5μm中波段有效、牢固的减反射膜膜层,计算双层减反射膜的最小平均反射率与固定一层折射率、改变另一层折射率的关系。用这种方法可以获得各种膜料的组合结果。把均匀的CdTe/CeF_3双层膜与外层膜折射率由单蒸发源蒸发混合膜制CeF_3+SrF_2或CeF_3+SrF_2+CaF_2合成的、经过改进的膜层作了比较。增加Y_2O_3结合层和同时蒸发两种膜料,使两种膜料在位相面上非均匀混合后,明显地提高了膜层的牢固度。 相似文献
11.
用电子束蒸发沉积方法在X切LBO(X-LBO)晶体上镀制了两种不同膜系结构的1 064和532 nm倍频增透膜,其中一种膜系结构为基底/ZrO2/Y2O3/Al2O3/SiO2/空气,另一种为基底/0.5Al2O3/ZrO2/Y2O3/Al2O3/SiO2/空气,两种膜系结构的主要差别在于有无氧化铝过渡层。测量了薄膜的反射率光谱曲线,发现两种增透膜在1 064和532 nm处的反射率均小于0.5%,实际镀制结果与理论设计曲线的差异主要是由材料折射率的变化引起的。且对样品在空气环境中进行了温度为473 K的退火处理,结果发现两种膜系结构均表现了较优异的光学性能,氧化铝过渡层的加入使薄膜具有强的热应力性能。 相似文献
12.
Al2O3/SiO2 films have been deposited as UV antireflection coatings on 4H-SiC by electron-beam evaporation and characterized by reflection spectrum, scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The reflectance of the Al2O3/SiO2 films is 0.33% and 10 times lower than that of a thermally grown SiO2 single layer at 276 nm. The films are amorphous in microstructure and characterize good adhesion to 4H-SiC substrate. XPS results indicate an abrupt interface between evaporated SiO2 and 4H-SiC substrate free of Si-suboxides. These results make the possibility for 4H-SiC based high performance UV optoelectronic devices with Al2O3/SiO2 films as antireflection coatings. 相似文献
13.
Design and preparation of frequency doubling antireflection coating with different thicknesses of interlayer were investigated for LiB3O5 (LBO) substrate. The design was based on the vector method. The thickness of the inserted SiO2 interlayer could be changed in a wide range for the four-layer design with two zeros at 1064 and 532 nm. The coatings without any interlayer and with 0.1 quarter-wave (λ/4), 0.3 λ/4, 0.5 λ/4 SiO2 interlayer were deposited respectively on LBO by using electron beam evaporation technique.All the prepared coatings with SiO2 interlayer indicated satisfying optical behavior. This expanded our option for the thickness of an interlayer when coating on LBO substrate. The prepared films with SiO2 interlayer showed better adhesion than that without any interlayer. The thickness of the interlayer affected the adhesion, the adhesion for the coating with 0.5 λ/4 SiO2 interlayer was not as good as the other two. 相似文献
14.
Refractive index inhomogeneity is one of the important characteristics of optical coating material, which is one of the key factors to produce loss to the ultra-low residual reflection coatings except using the refractive index inhomogeneity to obtain gradient-index coating. In the normal structure of antireflection coatings for center wavelength at 532 nm, the physical thicknesses of layer H and layer L are 22.18 nm and 118.86 nm, respectively. The residual reflectance caused by refractive index inhomogeneity(the degree of inhomogeneous is between -0.2 and 0.2) is about 200 ppm, and the minimum reflectivity wavelength is between 528.2 nm and 535.2 nm. A new numerical method adding the refractive index inhomogeneity to the spectra calculation was proposed to design the laser antireflection coatings, which can achieve the design of antireflection coatings with ppm residual reflection by adjusting physical thickness of the couple layers. When the degree of refractive index inhomogeneity of the layer H and layer L is-0.08 and 0.05 respectively, the residual reflectance increase from zero to 0.0769% at 532 nm. According to the above accuracy numerical method, if layer H physical thickness increases by 1.30 nm and layer L decrease by 4.50 nm, residual reflectance of thin film will achieve to 2.06 ppm. When the degree of refractive index inhomogeneity of the layer H and layer L is 0.08 and -0.05 respectively, the residual reflectance increase from zero to 0.0784% at 532 nm. The residual reflectance of designed thin film can be reduced to 0.8 ppm by decreasing the layer H of 1.55 nm while increasing the layer L of 4.94 nm. 相似文献
15.
Enhanced laser induced damage threshold of dielectric antireflection coatings by the introduction of one interfacial layer 总被引:1,自引:0,他引:1
A new method for increasing laser induced damage threshold (LIDT) of dielectric antireflection (AR) coating is proposed. Compared with AR film stack of H2.5L (H:HfO2, L:SiO2) on BK7 substrate, SiO2 interfacial layer with four quarter wavelength optical thickness (QWOT) is deposited on the substrate before the preparation of H2.5L film. It is found that the introduction of SiO2 interfacial layer with a certain thickness is effective and flexible to increase the LIDT of dielectric AR coatings. The measured LIDT is enhanced by about 50%, while remaining the low reflectivity with less than 0.09% at the center wavelength of 1064 nm. Detailed mechanisms of the LIDT enhancement are discussed. 相似文献
16.
This paper reports that stoichiometric, amorphous, and uniform Er2O3 films are deposited on Si(001) substrates by a radio frequency magnetron sputtering technique. Ellipsometry measurements show that the refractive index of the Er2O3 films is very close to that of a single layer antireflection coating for a solar cell with an air surrounding medium during its working wavelength. For the 90-nm-thick film, the reflectance has a minimum lower than 3% at the wavelength of 600 nm and the weighted average reflectances (400-1000 nm) is 11.6%. The obtained characteristics indicate that Er2O3 films could be a promising candidate for antireflection coatings in solar cells. 相似文献
17.