A comparative evaluation of the photocatalytic and optical properties of nanoparticulate ZnO synthesised by mechanochemical processing

In this study, mechanochemical processing has been used to manufacture a nanoparticulate powder of ZnO with a controlled particle size and minimal hard agglomeration. The suitability of this ZnO powder for use as either a photocatalyst or an optically transparent UV-filter was evaluated by comparing its optical and photocatalytic properties with those of three commercially available powders that were synthesised by chemical precipitation and flame pyrolysis. The ZnO powder synthesised by mechanochemical processing was found to exhibit high optical transparency and low photocatalytic activity per unit of surface area, which indicates that it is suitable for use in optically transparent UV-filters.

     

Diversity of TiO<Subscript>2</Subscript> nanopowders’ characteristics relevant to toxicity testing

In this study, the physicochemical properties of several commercial ultrafine TiO₂ powders and their behaviour in the as-received form and colloidal suspensions were analysed. Besides the particle size, the morphology and agglomeration state of the dry powders, dispersibility, ζ-potential and sedimentation in water and in phosphate-buffered saline (PBS) were studied. Also, leaching of ions from the powders during ageing in physiological solution and the ability of the photoactivated powders to decompose organic substances were evaluated. The examined TiO₂ powders revealed diversified characteristics when dispersed in water. In general, while in dry conditions the particle size appeared in the nano-range (down to 32 nm), the particles were agglomerated in aqueous suspensions at pH ~7 and only a minor amount showed dimensions below 200 nm, but none below 100 nm. The inherent pH of the 3 % suspensions varies from 3.7 to 7.5 and the surface charge at these pH values varied from highly positive to highly negative values. In PBS, the surface charge is negative and relatively low for all the samples, which resulted in agglomeration. Five out of six powders exhibited significant photocatalytic activity when exposed to UV irradiation. This also includes one cosmetic-grade powder. Furthermore, during the immersion in aqueous media at physiological temperature, the powders released foreign ions, which might also contribute to the results of cytotoxicity tests. The results revealed the major role of the particle surface charge and its impact on particle dispersion or agglomeration. Due to the high ionic strength in the liquids relevant for cell-surface interaction tests, for all the examined titania powders the nanoparticulate character was lost. However, the presence of impurities and photocatalysis might further contribute to the results of cytotoxicity tests.     

Immobilized TiO<Subscript>2</Subscript> nanoparticles produced by flame spray for photocatalytic water remediation

Anatase/rutile mixed-phase titanium dioxide (TiO₂) photocatalysts in the form of nanostructured powders with different primary particle size, specific surface area, and rutile content were produced from the gas-phase by flame spray pyrolysis (FSP) starting from an organic solution containing titanium (IV) isopropoxide as Ti precursor. Flame spray-produced TiO₂ powders were characterized by means of X-ray diffraction, Raman spectroscopy, and BET measurements. As-prepared powders were mainly composed of anatase crystallites with size ranging from 7 to 15 nm according to the synthesis conditions. TiO₂ powders were embedded in a multilayered fluoropolymeric matrix to immobilize the nanoparticles into freestanding photocatalytic membranes. The photocatalytic activity of the TiO₂-embedded membranes toward the abatement of hydrosoluble organic pollutants was evaluated employing the photodegradation of rhodamine B in aqueous solution as test reaction. The photoabatement rate of best performing membranes significantly overcomes that of membranes produced by the same method and incorporating commercial P25-TiO₂.     

Interfacial Reactions and Cubic Neodymium Oxide Formation in Low Dispersed Nd2O3-SiO2 System by Wet Chemical Method

Neodymium (binary oxide) powders are synthesized by a solgel technique. Prepared powders are heat treated under different temperature for different time duration and obtained nanostructure of Nd. Metal particle have diameters in the range 7.8-21.6nm. It is found that the heat treatment plays an important role to produce different structure of Nd-doped silica matrix. The peak position shifts to lower angle as the size of the nano metal oxide particles size increases.     

氧化锌纳米粉体的制备及其光催化性能研究

采用溶胶-凝胶法制备了氧化锌光催化剂,分别利用XRD、TG、FT-IR对所制粉体进行了表征。结果表明ZnO为六方晶系纤锌矿型,粒子大小约为27nm。粉体的IR光谱表明,热处理后NH基团和单乙酸锌的吸收峰消失,在470cm-1附近出现Zn-O伸缩振动。纳米粉体的光催化降解水杨酸实验结果显示出,焙烧后所得的纤锌矿型ZnO粉体具有较高的光催化活性,以310nm波长光照射16小时可降解水杨酸95.1%。     

Low-temperature hydrothermal synthesis of highly photoactive mesoporous spherical TiO2 nanocrystalline

TiO₂ microspheres with mesoporous textural microstructures and high photocatalytic activity were prepared by hydrothermal treatment of mixed solution of titanium sulfate and urea with designed time. The prepared samples were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and N₂ adsorption-desorption measurements. The photocatalytic activity was evaluated via the photocatalytic oxidation of acetone in air at room temperature. The results show that the hydrothermal time significantly influences on the morphology, microstructure and photocatalytic activity of the as-prepared samples. With increasing hydrothermal time, specific surface areas and pore volumes decrease, contrarily, the crystallite size and relative anatase crystallinity increase. The photocatalytic efficiency of the as-prepared samples is obviously higher than that of commercial Degussa P25 (P25) powders. Especially, the as-prepared TiO₂ powders by hydrothermal treatment for 7 h shows the highest photocatalytic activity, which exceeds that of P25 by a factor of more than 2 times.     

Optical and photocatalytic properties of nanocrystalline TiO2 synthesised by solid-state chemical reaction

Nanoparticulate TiO₂ is of interest for a variety of technological applications, including optically transparent UV-filters and photocatalysts for the destruction of chemical waste. The successful use of nanoparticulate TiO₂ in such applications requires an understanding of how the synthesis conditions effect the optical and photocatalytic properties. In this study, we have investigated the effect of heat treatment temperature on the properties of nanoparticulate TiO₂ powders that were synthesised by solid-state chemical reaction of anhydrous TiOSO₄ with Na₂CO₃. It was found that the photocatalytic activity increased with the heat treatment temperature up to a maximum at 600 °C and thereafter declined. In contrast, the optical transparency decreased monotonically with the heat treatment temperature. These results indicate that solid-state chemical reaction can be used to prepare powders of nanoparticulate TiO₂ with properties that are optimised for use as either optically transparent UV-filters or photocatalysts.     

Economical synthesis of nanocrystalline alumina using an environmentally low-cost binder

Sol-gel, a commonly used technique, involves the formation of an amorphous gel from a precursor solution. In this research nanocrystalline alumina powders have been synthesized through a new sol-gel simplified method. The route involved using an environmentally low-cost binder and aluminum nitrate in an aqueous medium. The added metal ions were dispersed in the gelled binder matrix. The gelled mass was dried and characterized by simultaneous thermogravimetric and differential thermal analysis (TG-DTA) and calcined at 350, 400, 530, 650, and 900 °C for 2 h. The samples were evaluated by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The used binder can be applied to form a perfect matrix for the entrapment of metal ions that during heat treatment, gives rise to ultrafine amorphous or crystalline alumina particles. In this study, the transition phases of alumina with particle sizes of 15-25 nm as well as aluminum oxide hydrate phase were produced by the heat treatment of the gelled mass at temperature 650 °C. By increasing the calcinations temperature to 900 °C, alumina transition phases were changed and aluminum oxide hydrate eliminated. The particle sizes at this temperature were obtained in the range 15-30 nm. The particle size and crystallite size of products measured from XRD and TEM were in good agreement.     

Characterization of ultrafine zirconia and iron oxide powders prepared under hydrothermal conditions

Abstract

Nanocrystalline zirconia (6-20 nm) and iron oxide (20-80 nm) powders were produced by hydrothermal treatment of corresponding hydroxides and nitrate solutions. The synthesis parameters (temperature, duration, concentration) allow fabrication of ultrafine oxide powders with various particle size and morphology. The smallest particles were produced by short-time (4-7 s) treatment of nitrate solutions (PH ≈ 1). Prepared nanocrystalline powders exhibit high activity in model solid state reactions.     

Improvement of photocatalytic behavior of chemical-vapor-synthesized TiO2 nanopowders by post-heat treatment

Anatase-type TiO₂ nanopowders less than 10 nm in average diameter were synthesized by a chemical vapor synthesis method. The TiO₂ nanopowders showed very poor photocatalytic properties, in spite of their large surface area. With subsequent heat treatment of the TiO₂ powders, their photocatalytic properties determined by measuring the degradation of 2-propanol were improved at temperatures up to 600 °C and then diminished along with formation of a rutile phase. This improvement in the photocatalytic properties of TiO₂ nanopowders was attributed to both a morphology change and a change in the electronic surface characteristics of TiO₂ particles during heat treatment.     

Photoluminescence and photocatalytic activity of zinc tungstate powders

ZnWO₄ powders with grain size in range 20 nm–10 μm have been synthesized by a simple combustion method and subsequent calcinations. The photocatalytic activities of powders were tested by degradation of methylene blue solution under UV light. The luminescence spectra and luminescence decay kinetics were studied and luminescence decay time dependence on average powder-grain size was obtained. The correlation between self-trapped exciton luminescence decay time and photocatalytic activity of ZnWO₄ powders was shown. A model explaining the excitonic luminescence decay time correlation with photocatalytic activity was proposed.     

Synthesis and characterization of nanocrystalline titanium nitride powder from rutile and anatase as precursors

In this research nanosized titanium nitride powder was synthesized through reaction of titanium oxide with ammonia gas. The reaction was carried out at a very slow heating rate. Two different TiO₂ starting powders contained rutile and anatase phase and differed in initial particle size and surface area. The crystallite size of TiN powders synthesized at 1000 °C was obtained about 40 nm for anatase sample. Surface area and particle size were found to be 19 m²/g, 70 nm for rutile sample and 31 m²/g, 39 nm for anatase sample, respectively. The rutile sample showed an increasing trend in surface area during conversion to the nitride, whilst the anatase sample followed an adverse trend. TiN powder synthesized from anatase had the highest surface area and smallest particle size due to the specification of initial precursor.     

Charge-discharge characteristics of nanocrystalline Co3O4 powders via aerosol flame synthesis

Nanocrystalline Co₃O₄ powders were synthesized by aerosol flame synthesis (AFS) method for the anode of lithium ion batteries and the basic electrochemical properties were investigated. The effects of synthesis conditions and heat-treatment temperature on the morphology, crystallite size and electrochemical properties were investigated. As-prepared soot contained Co₃O₄, CoO and Co(OH)₂, which were eventually converted into cubic spinel Co₃O₄ by post heat treatment. The as-prepared particle size was in the range of 10-30 nm and grew to 50-85 nm by the heat treatment. With growing particle size and improved crystallinity, charge-discharge capacity and cycle performance were improved and the discharge capacity of the powder heat-treated at 700 °C was 571 mAh/g after 30 cycles, which was better than Co₃O₄ powder reported in the previous literature.     

Effect of calcination temperature on porous titania prepared from industrial titanyl sulfate solution

Porous titania with anatase phase was prepared via thermal hydrolysis of industrial titanyl sulfate solution, and subsequent calcination at different temperature. The as-prepared powders were characterized by TG, DSC, XRD, particle size distribution test, N₂ adsorption-desorption isotherm and SEM. Raising calcination temperature could accelerate the crystal growth, enlarge its specific surface area, pore diameter, and improve its photocatalytic activity. While too high temperature could destroy the pore structure even collapse. The optimal calcination temperature is 550 °C, and the obtained sample showed good thermal stability and high photocatalytic activity, with specific surface area of 189.3 m²/g and higher degree of crystallinity, and its photocatalytic degradation rate of methylene blue was of 95.76%.     

Phase transition of BiVO4 nanoparticles in molten salt and the enhancement of visible-light photocatalytic activity

BiVO₄ nanoparticles are prepared by molten salt method. Tetragonal BiVO₄ completely transforms to monoclinic phase after heating in molten LiNO₃ at 270 °C for 18 h. The average particle sizes of monoclinic BiVO₄ varied from 30 to 52 nm while the initial ratio of BiVO₄ to LiNO₃ changes from 1:6 to 1:24. The photocatalytic activity is evaluated by measuring decolorization of N,N,N′,N′-tetraethylated rhodamine dye solution under visible-light irradiation. Both of the de-ethylation and chromophore cleavage are responsible for the decolorization of RB. The sample with an average particle size of 52 nm and a moderate surface area of 10 m²/g exhibit the highest visible-light photocatalytic activity. The shift of Raman peak position indicates that the symmetry distortions in the local structure of the monoclinic BiVO₄. The variations of the local structure result in the modification of the electronic structure, which is responsible for the high visible-light photocatalytic activity.     

Fabrication of unique ribbon-like porous LaFeO3 nanofibers photocatalyst via electrospinning

Novel LaFeO₃ ribbon-like porous nanofibers have been fabricated by electrospinning utilizing sol–gel precursors, followed by heat treatment at 600 °C for 2 h. The crystal structure, surface morphology, and microstructure were investigated by thermogravimetry–differential thermal analysis, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy, respectively. The photocatalytic activity was investigated for the photodegradation of methylene blue aqueous solution. The result shows that the ribbon-like porous nanofibers exhibit excellent photocatalytic activity compared with ultrafine LaFeO₃ nanofibers and LaFeO₃ powders.     

Influence of acid catalysts on the structural and magnetic properties of nanocrystalline barium ferrite prepared by sol–gel method

BaFe₁₂O₁₉ powders with nanocrystalline size were prepared by sol–gel techniques. Nitric, hydrochloric, acetic and stearic acid were used to improve the magnetic properties. Amorphous gels were formed with Fe/Ba molar ratio of 10.5. Then powders were obtained by subsequent heat treatment at 800–1000 °C for 1 h. Barium ferrite powder was also synthesized by solid state reaction at 1210 °C. X-ray diffraction, scanning electron microscopy and transmission electron microscopy (TEM) experiments were conducted to evaluate structural properties of the samples. The value of the effective magnetic susceptibility was measured. The results show that the magnetoplumbite structure was formed in all of the powders. The TEM observation showed that the minimum particle size (20 nm) was produced with the stearic acid catalyst. The highest value of the effective magnetic susceptibility was achieved also using stearic acid.     

Synthesis of indium oxide nanoparticles by solid state chemical reaction

A three stage process consisting of mechanical milling, heat treatment, and washing has been investigated as a means of manufacturing nanoparticulate powders of In₂O₃. In the first stage of processing, mechanical milling was used to prepare a nanocrystalline mixture of In₂(SO₄)₃, Na₂CO₃, and NaCl. Subsequent heat treatment of the milled reactant resulted in the formation of nanocrystalline In₂O₃ particles embedded within a matrix of Na₂SO₄ and NaCl. In the final stage of processing, the In₂O₃ powder was recovered by washing with deionised water. The duration of milling was found to determine the degree of hard agglomeration in the final washed powder. It was also found that the average particle size of the powder could be controlled between 8 and 18 nm by simply varying the temperature of the post-milling heat treatment over the range of 400 to 550°C. These results demonstrate that solid state chemical reaction can be used as a technically simple method for manufacturing nanoparticulate In₂O₃ powders with a controlled particle size and low levels of hard agglomeration.     

Functional Nanostructured Silica Powders Derived from Colloidal Suspensions by Sol Spraying

The preparation of silica powders derived from sols with a variety of primary particle sizes from 4 to 100 nm and the influences of preparation conditions such as drying temperature and initial concentration of precursor on the final powders morphology were investigated for the first time. The prepared silica powders have spherical morphology, and the final diameter (between 0.1 and 2 um) was controlled by changing the concentration of starting colloidal suspension. The preparation of silica based luminescent powders was investigated by adding europium ion as the dopant. The Eu-doped silica powders showed a visible-luminescence with wavelength of 613 nm, a red emission, under excitation of 394 nm light source. The effects of Eu-doping concentration, operation temperature and primary particle size of silica sols on the luminescence were also investigated.     

Titanium dioxide nanoparticles prepared by laser pyrolysis: Synthesis and photocatalytic properties

TiO₂ nanoparticles were synthesized via the laser pyrolysis of titanium tetrachloride-based gas-phase mixtures. In the obtained nanopowders, a mixture of anatase and rutile phases with mean particle size of about 14 nm was identified. Using the thermal heated laser nanopowders, mechanically stable films were produced by immobilizing titania nanopowders on glass substrates (the doctor blading method followed by compression). The photocatalytic activity of the prepared films was tested by the degradation of 4-chlorophenol in an aqueous solution under UV-illumination. By referring to known commercial samples (Degussa P25) similarly prepared, higher photocatalytic efficiency was found for the laser-prepared samples.