Lithium antimonite: A new class of anode material for lithium-ion battery

LiSbO₃ has been synthesized by chemical mixing followed by thermal treatment at 800 °C. Field emission scanning electron microscopy revealed bar shaped multifaceted grains, 0.5–4 μm long and 0.5–1 μm wide, that cluster together as soft agglomeration. 2032 type coin cell vs Li/Li⁺ shows a flat charge–discharge plateau together with low Li intercalation/de-intercalation potential (0.2/0.5 V). A high discharge capacity of 580 mA h g^?1 has been obtained in the 1st cycle with 100% Coulombic efficiency. About 96% of the Coulombic efficiency is retained up to the 12th cycle, but at the 15th cycle, the Coulombic efficiency drops down to 88%. AC impedance spectroscopy shows an increase in electrolyte resistance (R_s) from 4.43 Ohm after the initial cycle to 12.4 Ohm after the 15th cycle indicating a probable dissolution of Sb into the electrolyte causing the capacity fading observed.     

Drastically enhanced cycle life of Co-B alloy electrode by 8-hydroxyquinoline at elevated temperature

The effect 8-hydroxyquinoline (8-HQ) additive in electrolyte on the cyclic stability of Co-B alloy electrode was investigated at elevated temperature (55 °C). Charge–discharge measurements show that 8-HQ can drastically enhance the cycle life of Co-B alloy electrode. Specifically, in the electrolyte containing 0.028 M 8-HQ additive, the discharge capacity of Co-B alloy electrode after 100 cycles are still up to 385.8 mAh/g at 55 °C. However, for the electrode in 8-HQ-free electrolyte, its discharge capacity is sharply decreased to only 138.5 mAh/g after 100 cycles. ICP-OES, XRD and ATR/FT-IR measurements were used to clarify the reason of the improvement in the cyclic stability. These results show that beneficial effect of 8-HQ on cycle life of Co-B alloy electrode can be attributed to the formation of insoluble complex (8-HQ)₂Co(II)·2H₂O protective layer that can suppress the dissolution of Co(OH)₂ into electrolyte at elevated temperature.     

Poly(ether amine) and cross-linked poly(propylene oxide) diacrylate thin-film polymer electrolyte for 3D-microbatteries

This paper presents a novel thin-film electrolyte of a 2:1 blend of polyetheramine (glyceryl poly(oxypropylene)) and cross-linked oligomeric poly(propylene oxide) diacrylate with LiTFSI. The polyetheramine acts as a surfactant, and can thereby be applied as a conformal coating on complex surfaces—here demonstrated for porous LiFePO₄ cathodes—making it useful for 3D-microbatteries. The poly(propylene oxide) diacrylate blends with the surfactant and is easily UV cross-linked, thereby ensuring good mechanical stability. Electrolytes, ~ 2 μm thick, were casted onto LiFePO₄ cathodes and cycled against metallic lithium, displaying stable discharge capacities of ~ 8 mAh/g at room temperature and ~ 120 mAh/g at 60 °C. The electrolyte showed conductivities of 3.45 × 10^? 6 and 5.80 × 10^? 5 S cm^? 1 at room temperature and 60 °C, respectively.     

Fabrication of solid thin film electrolyte and LiCoO2 by aerosol flame pyrolysis deposition

Aerosol flame pyrolysis deposition method was applied to deposit the oxide glass electrolyte film and LiCoO₂ cathode for thin film type Li-ion secondary battery. The thicknesses of as-deposited porous LiCoO₂ and Li₂O–B₂O₃–P₂O₅ electrolyte film were about 6 μm and 15 μm, respectively. The deposited LiCoO₂ was sintered for 2 min at 700 °C to make partially densified cathode layer, and the deposited Li₂O–P₂O₅–B₂O₃ glass film completely densified by the sintering at 700 °C for 1 h. After solid state sintering process the thicknesses were reduced to approximately 4 μm and 6 μm, respectively. The cathode and electrolyte layers were deposited by continuous deposition process and integrated into a layer by co-sintering. It was demonstrated that Aerosol flame deposition is one of the good candidates for the fabrication of thin film battery.     

Electrochemical properties of Li symmetric solid-state cell with NASICON-type solid electrolyte and electrodes

All-solid-state phosphate symmetric cells using Li₃V₂(PO₄)₃ for both the positive and negative electrodes with the phosphate Li_1.5Al_0.5Ge_1.5(PO₄)₃ as the solid electrolyte were proposed. Amorphous Li_1.5Al_0.5Ge_1.5(PO₄)₃ was added into the electrode to increase the interface area between the active materials and the electrolyte. Any other phases were not formed at the electrode/electrolyte interface even after hot pressing at 600 °C. The discharge capacity was 92 mAh g^? 1 at 22 µA cm^? 2 at 80 °C, and 38 mAh g^? 1 at 25 °C, respectively. Symmetric cell configuration leads to simplify the fabrication process for all-solid-state batteries and will reduce manufacturing costs.     

Low-temperature performance of LiFePO4/C cathode in a quaternary carbonate-based electrolyte

The low-temperature performance of LiFePO₄/C cathode in a quaternary carbonate-based electrolyte (1.0 M LiPF₆/EC+DMC+DEC+EMC (1:1:1:3, v/v)) was studied. The discharge capacities of the LiFePO₄/C cathode were about 134.5 mAh/g (20 °C), 114 mAh/g (0 °C), 90 mAh/g (−20 °C) and 69 mAh/g (−40 °C) using a 1C charge–discharge rate. Cyclic voltammetry measurements show obviously sluggish of the lithium insertion–extraction process of the LiFePO₄/C cathode as the operation temperature falls below −20 °C. Electrochemical impedance analyses demonstrate that the sluggish of charge-transfer reaction on the electrolyte/LiFePO₄/C interface and the decrease of lithium diffusion capability in the bulk LiFePO₄ was the main performance limiting factors at low-temperature.     

Superior high-rate cycling performance of LiFePO4/C-PPy composite at 55 °C

A facile chemical polymerization method was applied to prepare LiFePO₄/C-PPy composite using Fe(III)tosylate as oxidant. The as-prepared LiFePO₄/C-PPy sample with PPy content of approximately 4 wt% showed great rate capability with a discharge capacity of 115 mAh/g at 20C. High temperate cycling performance of the LiFePO₄/C-PPy sample was compared with bare LiFePO₄/C at 5C charge–discharge rate at 55 °C. The LiFePO₄/C-PPy cathode showed superior cycling stability with an initial capacity of 155 mAh/g. Ninety percentage of this initial capacity was retained after 300 cycles, compared to 40% of that of bare LiFePO₄/C. The LiFePO₄/C-PPy electrode showed stable discharge plateau voltage of 3.35–3.25 V vs. Li⁺/Li during long term cycling. The superior performance of the LiFePO₄/C-PPy electrode was due to the enhanced electrical conductivity, negligible iron dissolution and alleviated electrode cracking contributed by PPy coating.     

All-solid-state micro lithium-ion batteries fabricated by using dry polymer electrolyte with micro-phase separation structure

Micro-batteries were fabricated by using BAB block copolymer as dry polymer electrolyte, which consisted of polyethylene oxide and polystyrene and had relatively high ionic conductivity at room temperature. The micro-batteries were fabricated by a sol–gel method combined with micro-injection system. Two types of micro-battery were fabricated. One consists of a single cell and another of 3-cells connected in series. LiMn₂O₄ and Li_4/3Ti_5/3O₄ were used as active materials in positive and negative electrode, respectively. The micro-array batteries were operated at room temperature without any plasticizer in the polymer electrolyte. The operation voltages were 2.45 V and 7.40 V for a single cell and 3-cell array, respectively. The discharge capacities estimated from cyclic voltammetry measurements were 245 nA h for a single cell and 12.1 nA h for a 3-cell array, which corresponded to the energy densities of 8.48 μW h cm⁻² and 4.54 μW h cm⁻², respectively.     

Surface structures and electrochemical characteristics of surface-modified carbon anodes for lithium ion battery

Petroleum coke and those heat-treated at 1860 °C, 2100 °C, 2300 °C 2600 °C and 2800 °C (abbreviated as PC, PC1860, PC2100, PC2300, PC2600 and PC2800) were fluorinated by elemental fluorine of 3 × 10⁴ Pa at 200 °C and 300 °C for 2 min. Natural graphite powder samples with average particle sizes of 5 μm, 10 μm and 15 μm (abbreviated as NG5μm, NG10μm and NG15μm) were also fluorinated by ClF₃ of 3 × 10⁴ Pa at 200 °C and 300 °C for 2 min. Transmission electron microscopic (TEM) observation revealed that closed edge of PC2800 was destroyed and opened by surface fluorination, which increased the first coulombic efficiencies of PC2300, PC2600 and PC2800 by 12.1–18.2% at 60 mA/g and by 13.3–25.8% at 150 mA/g in 1 mol/dm³ LiClO₄–ethylene carbonate (EC)/diethyl carbonate (DEC) (1:1 in volume). Light fluorination of NG10μm and NG15μm increased the first coulombic efficiencies by 22.1–28.4% at 150 mA/g in 1 mol/dm³ LiClO₄–EC/DEC/PC (PC: propylene carbonate, 1:1:1 in volume).     

Li0.93[Li0.21Co0.28Mn0.51]O2 nanoparticles for lithium battery cathode material made by cationic exchange from K-birnessite

Li_0.93[Li_0.21Co_0.28Mn _0.51]O₂ nanoparticles with an R-3m space group is hydrothermally prepared from Co_0.35Mn_0.65O₂ obtained from an ion-exchange reaction with K-birnessite K_0.32MnO₂ at 200 °C. Even at a hydrothermal reaction temperature of 150 °C, the spinel (Fd3m) phase is dominant, and a layered phase became dominant by combining an increase in the temperature to 200 °C with an increase in lithium concentration. The as-prepared cathode particle has plate-like hexagonal morphology with a size of 100 nm and thickness of 20 nm. The first discharge capacity of the cathode is 258 mAh/g with an irreversible capacity ratio of 22%, and the capacity retention after 30 cycles is 95% without developing a plateau at ∼3 V. Capacity retention of the cathode discharge is 84% at 4C rate (=1000 mA/g) and shows full capacity recovery when decreasing the C rate to 0.1 C.     

High performance cathode-supported SOFC with perovskite anode operating in weakly humidified hydrogen and methane

A high performance cathode-supported solid oxide fuel cell (SOFC), suitable for operating in weakly humidified hydrogen and methane, has been developed. The SOFC is essentially made up by a YSZ/LSM composite supporting cathode, a thin YSZ film electrolyte, and a GDC-impregnated La_0.75Sr_0.25Cr_0.5Mn_0.5O₃ (LSCM) anode. A gas tight thin YSZ film (∼27 μm) was formed during the co-sintering of cathode/electrolyte bi-layer at 1200 °C. The cathode-supported SOFC developed in this study showed encouraging performance with maximum power density of 0.182, 0.419, 0.628 and 0.818 W cm⁻² in air/3% H₂O–97% H₂ (and 0.06, 0.158, 0.221 and 0.352 W cm⁻² in air/3% H₂O–97% CH₄) at 750, 800, 850 and 900 °C, respectively. Such performance is close to that of the cathode-supported cell (0.42 W cm⁻² vs. 0.455 W cm⁻² in humidified H₂ at 800 °C) developed by Yamahara et al. [Solid State Ionics 176 (2005) 451–456] with a Co-infiltrated supporting LSM-YSZ cathode, a (Sc₂O₃)_0.1(Y₂O₃)_0.01(ZrO₂)_0.89 (SYSZ) electrolyte of 15 μm in thickness and a SYSZ/Ni anode, indicating that the performance of the GDC-impregnated LSCM anode is comparable to that made of Ni cermet while stable in weakly humidified methane fuel.     

Coupled triple phase boundary processes: Liquid–liquid generator–collector electrodes

Electrochemical processes at liquid–liquid–electrode interfaces involve simultaneous ion transfer and electron transfer. When driven at triple phase boundary electrode systems, electron and ion transfer occur in the same interfacial reaction zone. In this report, preliminary work with a novel electrode system based on two coupled triple phase boundary reaction zones is described. An interdigitated gold band array with 7 μm gold bands separated by 13 μm gaps is employed immersed in aqueous electrolyte with a water-immiscible solution of the redox system N,N-diethyl-N′N′-didodecyl-phenylenediamine (DDPD) in 4-(3-phenylpropyl)-pyridine (PPP) immobilized on the surface. Well-defined generator–collector feedback currents are observed which depend on the volume of deposit, the concentration of the redox system, and the nature of the aqueous electrolyte.     

LixV2O5 nanobelts for high capacity lithium-ion battery cathodes

5–10 μm long, typically 200–300 nm wide, and several nanometers thick Li_xV₂O₅ (× ～ 0.8) nanobelts with the δ-type crystal structure were synthesized by a hydrothermal treatment of Li⁺-exchanged V₂O₅ gel. When dried at 200 °C under vacuum prior to electrochemical testing, the as-prepared nanobelts underwent the well-known δ → ε → γ-phase transition giving a mixture of ε and γ phases as a nanocomposite electrode material. Such a simple preparation procedure guarantees a yield of material with drastically enhanced initial discharge specific capacity of 490 mAh/g and great cyclability. The enhanced electrochemical performance is attributed to the complex of experimental procedures including post-synthesis treatment of the single-crystalline Li_xV₂O₅ nanobelts.     

Study on dynamics of structural transformation during charge/discharge of LiFePO4 cathode

Structural transformation taking place during charge/discharge of the LiFePO₄ electrode in an organic Li-ion electrolyte has been studied by in situ synchrotron X-ray diffraction (XRD) concurrently with electrochemical analysis. The data reveal complex structural transformation patterns which result from significantly delayed structural transformation, even at low to moderate current rates (C/10 ∼ 1 C). The extent of the deviation is affected by charge/discharge conditions as well as history, and strong deviation appears detrimental to electrode cycle life. Furthermore, the two-phase characteristic of the Li⁺ insertion/extraction reactions is found to persist even within one metastable crystal structure. The result suggests the presence of domain structures that are probably caused by the strong electron/ion site coulombic interaction as previously suggested.     

Fabrication of a large area cathode-supported thin electrolyte film for solid oxide fuel cells via tape casting and co-sintering techniques

A large area cathode-supported electrolyte film, comprising porous (La_0.8Sr_0.2)_0.95MnO₃ (LSM95) cathode substrate, LSM95/Zr_0.89Sc_0.1Ce_0.01O_2?x (SSZ) cathode active layer, and SSZ electrolyte, has been successfully fabricated by tape casting and co-sintering techniques. The interface reaction between cathode and electrolyte was inhibited by using A-site deficient LSM. A dense enough SSZ thin film with a thickness of ～26 μm was obtained at 1250 °C. By using Pt as anode, the obtained single cell reached the maximum power density of 0.54 W cm^?2 at 800 °C in O₂/humidified H₂, with open circuit voltage (OCV) value of 1.08 V.     

Direct electrochemical response of Myoglobin using a room temperature ionic liquid, 1-(2-hydroxyethyl)-3-methyl imidazolium tetrafluoroborate,as supporting electrolyte

Direct electrochemical response of Myoglobin (Myb) at the basal plane graphite (BPG) electrode was observed when a room temperature ionic liquid (RTIL), 1-(2-hydroxyethyl)-3-methyl imidazolium tetrafluoroborate ([HEMIm][BF₄]), was used as the supporting electrolyte. In a 0.17 M [HEMIm]BF₄ aqueous solution, a couple of well-defined redox peaks of Myb could be obtained, whose anodic and cathodic peak potentials were at −0.158 and −0.224 V (vs. Ag/AgCl), respectively. Both anodic and cathodic peak currents increased linearly with the potential scan rate. Compared with the supporting electrolyte of phosphate buffer, [HEMIm][BF₄] played an obvious promotion for the direct electron transfer between Myb and the BPG electrode. Further investigation suggested that Myb was adsorbed tightly on the surface of the BPG electrode in the presence of [HEMIm][BF₄] to form a stable, approximate monolayer Myb film. Myb adsorbed on the BPG electrode surface showed a remarkable electrocatalytic activity for the reduction of oxygen in a [HEMIm][BF₄] aqueous solution. Based on these, a third-generation biosensor could be constructed to directly detect the concentration of oxygen in aqueous solution with a limit of detection of 2.3 × 10⁻⁸ M.     

New approaches to improve cycle life characteristics of lithium–sulfur cells

Two different approaches were tried for an improvement of the cycle performance of Li–S cells: (1) A mixed polymer binder system of polyvinyl pyrrolidone (PVP) and polyethyleneimine (PEI) was developed to maintain the initial morphology of the carbon electrodes, the positive electrode of the Li–S cells, during charge–discharge cycles; (2) a tetrabutylammonium (TBA)-based mixed salt system was applied to an organic liquid electrolyte of the Li–S cells to change certain chemical reactions of polysulfides in the electrolyte solutions. The Li–S cells with PEI showed a significant improvement in cycle performance as well as in discharge capacity, compared with the Li–S cells using PVP only. The discharge capacity at the 50th cycle was found to be ∼580 mAh/g-sulfur, 83% of an initial capacity (∼720 mAh/g-sulfur), at a high current density of 2.0 mA cm⁻². It was observed that the Li–S cells with a mixed electrolyte of 0.5 M LiCF₃SO₃/0.5 M TBAPF₆ did not show a distinct improvement in the aspect of discharge capacity. The Li–S cells, however, showed a significant enhancement in the cycle life characteristics much better than that of Li–S cells with 1.0 M LiCF₃SO₃.     

An acidic cellulose–chitin hybrid gel as novel electrolyte for an electric double layer capacitor

A novel acidic cellulose–chitin hybrid gel electrolyte including binary ionic liquids (ILs) with an aqueous H₂SO₄ solution was prepared for an electric double layer capacitor (EDLC). Its electrochemical characteristics were investigated by galvanostatic charge–discharge measurements. The test cell with a hybrid gel electrolyte shows a specific capacitance of 162 F g^?1 at room temperature, which is higher than that for a cell with an H₂SO₄ electrolyte, 155 F g^?1. This hybrid gel electrolyte exhibits excellent high-rate discharge capability in a wide range of current densities as well as an aqueous H₂SO₄ solution. The discharge capacitance of the test cell can retain over 80% of its initial value in 100,000 cycles even at a high current density of 5000 mA g^?1.     

Cobalt-free cathode material SrFe0.9Nb0.1O3−δ for intermediate-temperature solid oxide fuel cells

A cobalt-free cubic perovskite oxide, SrFe_0.9Nb_0.1O_3?δ (SFN) was investigated as a cathode for intermediate-temperature solid oxide fuel cells (IT-SOFCs). XRD results showed that SFN cathode was chemically compatible with the electrolyte Sm_0.2Ce_0.8O_1.9 (SDC) for temperatures up to 1050 °C. The electrical conductivity of SFN sample reached 34–70 S cm^?1 in the commonly operated temperatures of IT-SOFCs (600–800 °C). The area specific resistance was 0.138 Ω cm² for SFN cathode on SDC electrolyte at 750 °C. A maximum power density of 407 mW cm^?2 was obtained at 800 °C for single-cell with 300 μm thick SDC electrolyte and SFN cathode.     

“Water-in-Salt” electrolyte enabled LiMn2O4/TiS2 Lithium-ion batteries

High electrochemical reversibility of the TiS₂ anode in “Water-in-Salt” electrolyte (21 m LiTFSI in H₂O) is demonstrated for the first time. The wide electrochemical window and low chemical activity of H₂O in the “Water-in-Salt” electrolyte not only significantly enhanced the electrochemical reversibility of TiS₂ but also effectively suppressed the hydrolysis side reaction in the aqueous electrolyte. Paired with a LiMn₂O₄ cathode, the LiMn₂O₄/TiS₂ full cell delivers a relatively high discharge voltage of 1.7 V and an energy density of 78 Wh kg^− 1 as well as a satisfactory rate performance.