一种测定溶解氧用电荷转移络合物修饰电极

1 引 言溶解氧(DO)是一种水质综合指示〔1〕。其经曲测定方法如Winkler〔2〕法及改进方法耗时多、成本高、操作繁琐。氧电极〔3〕可以较方便地在现场使用，但灵敏度和精度较差。本文报道一种Cu2+-邻菲■啉－1，2－二氰基－1，2－二巯基乙烯电荷转移三元络合物〔4，5〕化学修饰电极，因其较低的可逆氧化还原电位和电荷转移特性，对DO发生平行催化还原而实现测定。2 实验部分2.1 仪器与试剂 BAS－100A电化学分析仪(BAS公司)，Ag/AgCl参比电极，Pt辅助电极。Cu2+邻菲■啉－1,2－二氰基－1，2－二巯基乙烯三元络合物：实验室合成；石墨…     

铁卟啉修饰电极催化氧化测定儿茶酚类化合物

将铁卟啉氯化－５，１０，１５，２０－四－（－３－甲氧基－４－羟基苯基）卟啉铁（ＴＭＨＰＰ·ＦｅＣｌ）修饰在玻碳电极表面，制备成对儿茶酚类化合物具有高的响应的ＴＭＨＰＰ·ＦｅＣｌ修饰电极。该电极对多巴胺、肾上腺素等儿茶酚类化合物在各自的响应区间内有良好的线性关系，电极具有灵敏度高、响应快、稳定性好等特点。电极响应时间小于１０ｓ，儿茶酚类检测浓度在１０（－６）ｍｏｌ／Ｌ数量级。     

普鲁士蓝膜修饰电极循环伏安行为的研究

本文研究普鲁士蓝(PB)膜修饰电极的循环伏安行为,结果表明,膜中电活性中心间的相互作用导致PB膜电极的伏安行为偏离理想表面波.用有限扩散边界模型解释了高电位扫速下膜电极的伏安行为.在含钾离子的电解质溶液中测得PB膜中电荷传输扩散系数为10~(-9)～10~(-11)cm~2/s.     

钴原卟啉附修饰玻碳电极为基底的胆固醇酶电极

本文利用钴原卟啉对H₂O₂氧化有很高催化活性的特点,以钴原卟啉修饰玻碳电极为基底,戊二醛交联法固定胆固醇氧化酶,以电聚合邻苯二胺膜抗干扰、抗毒化.得到了线性范围为0.1～2mmol/L,响应时间在30s以内,可连续使用150次的胆固醇酶电极.     

用X射线光电子能谱对热处理的四苯基钴卟啉修饰电极的表面表征

本文用XPS、DTA和TG分析了四苯基钴卟啉化学修饰电极的热分解行为, 它不同于四苯基铁卟啉. 由XPS谱图揭示了四苯基钴卟啉与玻璃碳电极之间的相互作用, 进而阐述了经热处理的四苯基钴卟啉化学修饰电极的表面结构与电催化稳定性的关系. 从Co2p_3/2和2p_(1/2)能级的自旋分裂间距及其Shake-up伴峰, 了解经热处理后的四苯基钴卟啉修饰电极中钴自旋态变化, 并且从Co的L_3VV俄歇跃迁计算出Co的双电离能, 其双电离能与电催化活性有一定关系。     

三正辛胺修饰电极伏安测定痕量金的研究

用化学修饰电极伏安测定痕量金,Kalcher K等曾采用阴离子交换剂碳糊修饰电极及打萨宗碳糊修饰电极检测100～300μg/L的金。本文采用三正辛胺(TOA)修饰玻碳电极,在1.5 mol/L介质中,Au(Ⅲ)在+0.16 V(vs SCE)处有一灵敏的不可逆还原峰。检出限为0.1μg/L。灵敏度比文献方法高千倍。Au(Ⅲ)浓度在5×10~(-7)～5×10~(-9)mol/L范围内峰高与浓度     

石墨烯修饰玻碳电极用于循环伏安法测定抗坏血酸

采用Hummers法制备了纳米石墨烯,并将该纳米材料分散在蒸馏水中得到悬浮液,取5μL的悬浮液滴涂在玻碳电极表面,制备石墨烯修饰电极。用循环伏安法研究了在pH 4.0磷酸盐电解质中,在-0.4～0.8V(vs.Ag/AgCl)电位范围内,抗坏血酸在修饰电极上的电化学行为。结果表明:抗坏血酸在修饰电极上在0.173V处可见明显的氧化峰,且氧化峰电流显著高于在裸玻碳电极上的氧化峰电流;并可有效排除肾上腺素、尿酸、多巴胺等物质的干扰。据此提出了用循环伏安法测定抗坏血酸的方法。抗坏血酸的线性范围为8.00×10-6～1.0×10-3 mol.L-1,检出限(3S/N)为1.0×10-7 mol.L-1。方法用于维生素C片的分析,回收率在96.3%～104.4%之间。     

单壁碳纳米管修饰电极循环伏安法测定盐酸利多卡因

将单壁碳纳米管(SWCNT′s)分散在10g.L-1十二烷基磺酸钠溶液中并滴涂在玻碳电极表面,红外灯烘干后,制备了单壁碳纳米管修饰电极。采用循环伏安法研究了盐酸利多卡因在修饰电极上的电化学行为。结果表明:盐酸利多卡因在该修饰电极上出现了一个灵敏的氧化峰,其峰电流比在裸玻碳电极上增大了5倍。据此提出了用循环伏安法测定盐酸利多卡因的方法。盐酸利多卡因的浓度在0.9～50.0μmol.L-1范围内,氧化峰电流与其浓度呈线性关系,检出限(3S/N)为0.3μmol.L-1。修饰电极用于盐酸利多卡因注射液中盐酸利多卡因的测定,测定值与标示值相符,加标回收率在98.0%～105%之间。     

用银-色氨酸复合膜修饰玻碳电极循环伏安法测定去甲肾上腺素

在含有1.0mmol.L-1硝酸银、5.58×10-2 mol.L-1色氨酸的溶液中,于-0.8～1.8V(vs.Ag/AgCl)电位下,在玻碳电极表面电沉积一层银-色氨酸复合膜,制得银-色氨酸复合膜修饰玻碳电极(Ag-TRY/GCE)。采用扫描电镜对电极表面的性能进行表征,循环伏安法对其电化学性能进行研究。试验发现:在pH 6.0磷酸盐缓冲溶液中,去甲肾上腺素(NE)在修饰电极出现一对明显的氧化还原峰,氧化峰电位为0.306V,还原峰电位为0.368V,提出了用循环伏安法测定NE的方法。在试验条件下,氧化峰电流与去甲肾上腺素浓度在3.4×10-7～8.3×10-6 mol.L-1和8.3×10-6～1.1×10-4 mol.L-1两段范围内呈线性关系,检出限(3S/N)为4.3×10-8 mol.L-1。修饰电极用于药物中去甲肾上腺素的测定,加标回收率在95.6%～99.4%之间。     

一步法制备钯纳米粒子修饰的多孔金电极及其对溶解氧的电催化

建立了只需一步操作即可完成在抛光洗净的金微盘阵列电极上进行多孔化处理和钯纳米粒子修饰的方法。通过对金微盘电极连续施加3个电位,分别实现金的氧化、金的还原和电沉积钯纳米粒子。利用扫描电镜和电化学方法监控制备过程,得到的结果证实了本方法的可行性和有效性。考察了溶液pH值与氧化时间对结果的影响,在磷酸盐缓冲溶液(pH7)中氧化90s,得到的修饰电极的电化学活性面积是裸电极的42倍。同时,由于整个过程不需要更换溶液,且只需开启一次仪器,大大简化了实验操作。将制备的修饰电极用于溶解氧的电催化,对溶解氧的灵敏度达到0.1mA·L/(cm2·mg),优于文献报道结果。     

Measurement of Dissolved Oxygen in Biological Fluids by Using a Modified Carbon Paste Electrode

A modified carbon paste electrode was constructed for the determination of dissolved oxygen using diamino‐o‐benzoquinone (DABQ) as the modifier. The electrochemical behavior of the electrode in citrate buffer (pH 2.0) was studied. In the presence of dissolved oxygen (DO) both cathodic and anodic peak currents decreased, indicating a chemical reaction between modifier and O₂. The decrease in peak current was linearly proportional to the amount of dissolved oxygen in the concentration range of 252–1260 μM of DO. The electrode was utilized in the determination of DO in urine samples. The relative error and RSD of the method were 1.6% and 4.1%, respectively. The electrode was applied more than two months for the determination of DO without any significant divergence in its voltammetric response.     

用多壁碳纳米管修饰玻碳电极为工作电极循环伏安法测定辛硫磷

将多壁碳纳米管(MWCNT′s)置于硝酸-硫酸(1+1)溶液中回流6 h使之净化及功能化。取MWCNT′s 5 mg置于超纯水10 mL中经超声振荡20 min制得其悬浮液,取悬浮液10μL滴加在玻碳电极(GCE)表面,经自然干燥后即得用MWCNT′s修饰的玻碳电极(MWCNT′s/GCE)。基于此修饰电极对辛硫磷的催化还原反应,提出了蔬菜中辛硫磷的循环伏安测定法,在pH 4的乙酸盐支持电解质溶液中,在电位0.78 V(对SCE)处可见明显的还原峰,且其峰电流值与辛硫磷浓度在5.0×10-8~1.0×10-6mol.L-1之间呈线性关系。应用此法分析了两件蔬菜样品,并以此试样为基体加入标准溶液对方法进行回收及精密度试验,测得其回收率的平均值和相对标准偏差(n=5)分别依次为100.3%,96.5%及3.7%,3.2%。     

Electrocatalytic Reduction of Oxygen at Multi‐Walled Carbon Nanotubes and Cobalt Porphyrin Modified Glassy Carbon Electrode

The multi‐walled carbon nanotubes (MWNTs) modified glassy carbon electrode exhibited electrocatalytic activity to the reduction of oxygen in 0.1 M HAc‐NaAc (pH 3.8) buffer solution. Further modification with cobalt porphyrin film on the MWNTs by adsorption, the resulted modified electrode showed more efficient catalytic activity to O₂ reduction. The reduction peak potential of O₂ is shifted much more positively to 0.12 V (vs. Ag/AgCl), and the peak current is increased greatly. Cyclic voltammetry (CV), transmission electron microscopy (TEM), X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM), were used to characterize the material and the modified film on electrode surface. Electrochemical experiments gave the total number of electron transfer for oxygen reduction as about 3, which indicated a co‐exist process of 2 electrons and 4 electrons for reduction of oxygen at this modified electrode. Meanwhile, the catalytic activities of the multilayer film (MWNTs/CoTMPyP)_n prepared by layer‐by‐layer method were investigated, and the results showed that the peak current of O₂ reduction increased and the peak potential shifted to a positive direction with the increase of layer numbers.     

钠型蒙脱石修饰碳糊电极测定微量的铜离子

报道了一种高灵敏度 ,快速测定水体中铜离子的化学修饰碳糊电极。详细研究了测定铜离子的条件。该修饰电极测定铜离子的线性范围为 1× 1 0 - 9～ 1 .5× 1 0 - 7mol/L ,富集 6min后的检出限为 3× 1 0 - 10 mol/L。该方法简便、快速、灵敏。用该修饰电极测定了实际水样中的铜离子 ,平均回收率为 1 0 0 .8%。     

Electrochemical Behavior and Voltammetric Determination of Diclofenac at a Multi-Walled Carbon Nanotube-Ionic Liquid Composite Modified Carbon Ceramic Electrode

This work describes the electrochemical behavior of diclofenac on the surface of a carbonceramic electrode (CCE) modified with multi-walled carbon nanotubes (MWCNT) and an ionic liquid (IL) composite. The MWCNT-IL composite showed an enhancement effect in the electro-oxidation of diclofenac with respect to a bare carbon ceramic electrode. Based on the experimental outcomes, a possible mechanism for the electro-oxidation of diclofenac is proposed and discussed. Under the optimized experimental conditions, the MWCNT-IL CCE showed a linear response to diclofenac over the concentration range 50 nM–20 µM with a detection limit of 27 nM. The developed diclofenac sensor showed good stability, sensitivity, and reproducibility in the measurement of diclofenac in human blood plasma samples.     

Polyviologen Modified Glassy Carbon Electrode Employed for Anodic Stripping Voltammetric Determination of Mercury(II)

In this study, a polyviologen modified glassy carbon electrode (PVGCE) was used to detect Hg(II) in aqueous solutions containing significant amounts of chloride anions in order to demonstrate the electroanalytical application of the electropolymerized polyviologen. The polyviologen thin film was formed on the electrode surface by applying a constant potential of ?1.0 V in the pH 4.2 Britton–Robinson (BR) buffer solution that contains 0.1 wt% of viologen oligomers. The PVGCE was found capability to improve the detection limit of Hg(II) in the solutions with high concentration of chloride because Hg(II) forms negative complex ions HgCl that can be accumulated to PVGCE by the anion‐exchange characteristic of polyviologen. With 5 minutes accumulation at ?0.2 V, the adsorbed HgCl anions were reduced to Hg and deposited on the electrode surface, and were determined with the following anodic stripping differential pulse voltammetry (ASDPV). The dependence of anodic stripping current versus concentration was linear from 1 ppb (5 nM) to 100 ppb (0.5 μM) with a regression coefficient of 0.9959.