Effect of surface acidity and basicity of aluminas on asphaltene adsorption and oxidation

This study investigates the effect of surface acidity and basicity of aluminas on asphaltene adsorption followed by air oxidation. Equilibrium batch adsorption experiments were conducted at 25°C with solutions of asphaltenes in toluene at concentrations ranging from 100 to 3000 g/L using three conventional alumina adsorbents with different surface acidity. Data were found to better fit to the Freundlich isotherm model showing a multilayer adsorption. Results showed that asphaltene adsorption is strongly affected by the surface acidity, and the adsorption capacities of asphaltenes onto the three aluminas followed the order acidic>basic and neutral. Asphaltenes adsorbed over aluminas were subjected to oxidation in air up to 600°C in a thermogravimetric analyzer to study the catalytic effect of aluminas with different surface acidity. A correlation was found between Freundlich affinity constant (1/n) and the catalytic activity. Basic alumina that has the lowest 1/n value, depicting strongest interactions, has the highest catalytic activity, followed by neutral and acidic aluminas, respectively.     

Temperature-responsive solid-liquid separations with charged block-copolymers of poly(N-isopropyl acryamide)

Temperature responsive charged block-copolymers of poly(N-isopropylacrylamide) (PNIPAM) have been used in the solid-liquid separation of alumina mineral particles from aqueous solution. The effects of temperature, polymer charge-sign and fraction of charged segment have been investigated. Batch settling and adsorption studies showed that rapid sedimentation results for suspensions with polymers of opposite charge-sign to the particle surface-charge (counterionic) at 50 °C. Cooling the suspensions after flocculation at 50 °C was found to increase the final solids volume fraction of the sediment beds formed through a mechanism related to partial desorption of polymer and the reduction of the hydrophobic attraction. Suspension stability results after dosing with polymers of similar charge-sign to the particle surface-charge (co-ionic) at both 25 and 50 °C. Increasing the amount of polymer charge increased the influence of polymer charge-sign on the adsorption and solid-liquid separation behavior. The performance of the charged block copolymers are compared to that of the random charged copolymer and neutral homopolymer PNIPAM structures.     

Fabrication of Fe3O4/SiO2 core/shell nanoparticles attached to graphene oxide and its use as an adsorbent

Thermoresponsive gelling behavior of concentrated alumina suspensions with poly(acrylic acid) (PAA) and triblock copolymer (PEO(101)-PPO(56)-PEO(101), Pluronic F127) was investigated as a function of PAA concentration (0.4-1.2 mass%) for ceramic solid free forming. The copolymer species assemble into micelles at temperatures above 15°C, yielding aqueous physical gel. In this study, the concentrated alumina aqueous suspensions (φ=35 vol%) were first prepared using the anionic dispersant of PAA, and then the copolymer species (10 mass%) were dissolved at a cooled temperature at 10°C. The addition of the copolymer species had a negligible influence on the adsorption state of PAA onto the alumina surfaces. The PAA concentration needed for the saturation adsorption on the alumina surfaces was ~0.6 mass%. When the PAA concentration was this value or slightly less, the suspension became gel state at 30°C from low viscous state at 10°C. The thermally induced alumina gel had excellent viscoelastic properties, and thereby the three dimensional periodic ceramic structures were successfully fabricated by a direct colloidal printing method that using the gels as "solid" inks at the room temperature. On the other hand, when it exceeded the saturation adsorption limit, the gelling behavior was not observed, indicating that the non-adsorbing PAA species may partly suppress the micellization of the copolymer on the heating.     

Sorption and desorption of Eu(III) on alumina

Summary Effects of ionic strength and of fulvic acid on the sorption of Eu(III) on alumina were investigated by using a batch technique. The experiments were carried out at T=25±1 °C, pH 4-6 and in the presence of 1M NaCl. The results indicate that sorption isotherms of Eu(III) are linear at low pH values. The sorption-desorption of Eu(III) on alumina at pH 4.4 is reversible, but a sorption-desorption hysteresis is found at pH 5.0. Fulvic acid has an obvious positive effect on the sorption of Eu(III) on alumina at low pH values. The migration of Eu(III) in alumina was studied by using column experiments and ^152+154Eu(III) radiotracer at pH 3.8. For column experiments, Eu(III) sorbed on alumina can be desorbed completely from the solid surface at low pH values. The findings are relevant to the evaluation of lanthanide and actinide ions in the environment.     

Temperature responsive flocculation and solid-liquid separations with charged random copolymers of poly(N-isopropyl acrylamide)

Temperature-responsive random copolymers based on poly(N-isopropyl acrylamide) (PNIPAM) with 15 mol% of either acrylic acid or dimethylaminoethyl acrylate quaternary chloride were prepared. The effect of the charge and its sign were investigated in the solid-liquid separation of silica and alumina mineral suspensions. The results were compared to PNIPAM homopolymer of similar molecular weight. PNIPAM copolymers of the same charge as the particles (co-ionic PNIPAM) act as dispersants at both 25°C and 50°C. Flocculation occurs when counter-ionic PNIPAM facilitates selective aggregation and rapid sedimentation of minerals at both 25°C and 50°C. Adsorption and desorption studies showed that, unlike non-ionic PNIPAM, little desorption of the counter-ionic copolymers from the oxides occurred after cooling a suspension from 50°C to below the lower critical solution temperature. Thus, incorporation of counter-ionic charge into the temperature sensitive polymer PNIPAM was found to reduce the sediment bed consolidation upon cooling when compared to PNIPAM homopolymers. The lack of secondary consolidation upon cooling is attributed to attractive inter-particle forces, such as conventional polyelectrolyte flocculation mechanisms (bridging, charge neutralization or charge patch) which persist at both 25°C and 50°C when counter-ionic PNIPAM is used. On the other hand, it was possible to obtain rapid sedimentation with the counter-ionic PNIAPMs even when they were added to the suspension already at 50°C, a process which has not been possible with neutral PNIPAM homopolymers.     

Using bulk convection in a microtensiometer to approach kinetic-limited surfactant dynamics at fluid-fluid interfaces

The effects of carbon chain length and temperature were investigated on adsorption kinetics and surface tension of a group of slightly volatile, short carbon chain molecules: 1-octanol, 1-hexanol, and 1-butanol. Experiments were performed in a closed chamber where simultaneous adsorption from both sides of the vapor/liquid interface was considered. The dynamic (time dependent) and steady-state surface tensions were found to decrease with temperature ranging from 10 °C to 35 °C. It was shown that, at the final steady-state, the effect of adsorption from the vapor phase was much more important than that from the liquid phase especially for short carbon chain molecules (e.g., 1-butanol). The modified Langmuir equation of state and modified kinetic transfer equation, which account for adsorption from both sides of a vapor/liquid interface, were used to model the experimental data of the steady-state and dynamic surface tension, respectively. Modeling results showed that the equilibrium constants and adsorption rate constants were increased with temperature and carbon chain length. The maximum surface concentration showed a decrease with temperature and an increase with carbon chain length. Some variations in the fitting parameters were observed in the dynamic modeling. These variations may be due to the experimental errors or the limitations of the proposed model.     

Interfacial thermodynamics of gallic acid adsorption on a chargeable hydrophobic surface

The thermodynamics of adsorption of gallic acid (GA, 3,4,5-trihydroxylbenzoic acid) on the hanging mercury drop electrode (HMDE) surface was studied by temperature-dependent stripping voltammetry (TD-SV), at physiological pH 7.4. The thermodynamic parameters, e.g., Gibbs free energy, ΔG(ADS), enthalpy, ΔΗ(ADS) and entropy, ΔS(ADS), of adsorption have been determined at physiological temperatures 2-40 °C. Chemisorption of the radical species ≡[GA(OH)(2)(O(-))]* is the energetically important reaction. The thermodynamic data show a complex mechanism of adsorption of GA on the electrode surface, which is strongly dependent on temperature. At low-temperatures T<12 °C, adsorption is controlled by enthalpy, while at T>22 °C, adsorption is entropy driven. In the temperature range 12 °C and 22 °C, a combined enthalpy-entropy stabilization occurs. A mechanism is proposed which analyses the implication of thermodynamics to the interfacial adsorption of polyphenols with cell membranes under physiological conditions.     

Photo-catalytic oxidation of cyclohexane over TiO2: a novel interpretation of temperature dependent performance

The rate of cyclohexane photo-catalytic oxidation to cyclohexanone over anatase TiO(2) was studied at temperatures between 23 and 60 °C by in situ ATR-FTIR spectroscopy, and the kinetic parameters were estimated using a microkinetic model. At low temperatures, surface cyclohexanone formation is limited by cyclohexane adsorption due to unfavorable desorption of H(2)O, rather than previously proposed slow desorption of the product cyclohexanone. Up to 50 °C, the activation energy for photocatalytic cyclohexanone formation is zero, while carboxylates are formed with an activation energy of 18.4 ± 3.3 kJ mol(-1). Above 50 °C, significant (thermal) oxidation of cyclohexanone contributes to carboxylate formation. The irreversibly adsorbed carboxylates lead to deactivation of the catalyst, and are most likely the predominant cause of the non-Arrhenius behavior at relatively high reaction temperatures, rather than cyclohexane adsorption limitations. The results imply that elevating the reaction temperature of photocatalytic cyclohexane oxidation reduces selectivity, and is not a means to suppress catalyst deactivation.     

Annealing of silica to reduce the concentration of isolated silanols and peak tailing in reverse phase liquid chromatography

Non-porous, colloidal silica particles were annealed at three different temperatures, 800, 900 and 1050 °C. The adsorption of lysozyme, a probe of surface roughness, was consistent with progressively reduced surface roughness as temperature increased. The heat treated silica particles were rehydroxylated and then used to pack UHPLC columns. The cationic protein lysozyme was used to probe silanol activity, which exhibited progressively less tailing as the annealing temperature increased. FTIR spectroscopy confirmed that the abundance of isolated silanols on the surface was reduced by annealing at 900 °C or 1050 °C. FTIR also revealed that there was markedly increased hydrogen bonding of the isolated silanols to neighbors after rehydroxylation. These results combine to support the hypothesis that (a) isolated silanols on silica cause tailing in RP-LC and (b) nonplanar topography gives rise to isolated silanols.     

Adsorption characteristics of As(V), Se(IV), and V(V) onto activated alumina: effects of pH, surface loading, and ionic strength

Arsenic, selenium, and vanadium are major anionic elements of concern in drinking water. This research investigated the adsorption characteristics of As(V), Se(IV), and V(V) onto a commercial activated alumina (AA) under different pH, surface loading, and ionic strength conditions using batch systems. The results indicated that the adsorption of these elements was significantly affected by pH and the surface loading. However, ionic strength generally did not impact their adsorption, indicating that the electrostatic effect on the adsorption of these elements was relatively not important compared to surface chemical reactions. A speciation-based adsorption model was used to simulate the adsorption of As(V), Se(IV), and V(V) by activated alumina and to determine the adsorption constants of different element species. This model can satisfactorily predict the adsorption of these elements in a broad pH range from 1.5 to 12 and a wide surface loading range from 1.0 to 50 mg/g activated alumina for different sorbent concentrations, using the same set of adsorption constants.     

Adsorption of CO and O2 on W2C(0001)

CO, O(2), and H(2) adsorption on a clean W(2)C(0001)√13×√13 R ± 13.9° reconstructed surface at room temperature (RT) were investigated using high-resolution electron energy loss spectroscopy (HREELS). The W(2)C(0001) adsorbs CO molecularly and adsorbs O(2) dissociatively, but does not adsorb H(2) at RT. In the CO adsorption system, two C-O stretching (antisymmetric CCO stretching) modes were found at 242.3 meV (1954 cm(-1)) and at 253.0 meV (2041 cm(-1)). The low-frequency site is occupied at first with subsequent conversion to the high-frequency site with increasing coverage. Additionally, a small peak was apparent at 104.5 meV (843 cm(-1)), and a middle peak at 50-51 meV (400-410 cm(-1)), which are assignable to a symmetric stretching mode and a hindered translational mode, respectively, of a CCO (ketenylidene) species. These observations are consistent with the CO adsorption model on top of the surface carbon. For oxygen adsorption, two adsorption states were found at 65.2-68.1 meV (526-549 cm(-1)) and 73.6 meV (594 cm(-1)): typical frequencies to oxygen adsorption on metal surfaces. Results suggest that atomic oxygen adsorption occurred on a threefold hollow site of the second W layer.     

Direct measurements of pore fluid density by vibrating tube densimetry

The densities of pore-confined fluids were measured for the first time by means of vibrating tube densimetry (VTD). A custom-built high-pressure, high-temperature vibrating tube densimeter was used to measure the densities of propane at subcritical and supercritical temperatures (between 35 and 97 °C) and carbon dioxide at supercritical temperatures (between 32 and 50 °C) saturating hydrophobic silica aerogel (0.2 g/cm(3), 90% porosity) synthesized inside Hastelloy U-tubes. Additionally, supercritical isotherms of excess adsorption for CO(2) and the same porous solid were measured gravimetrically using a precise magnetically coupled microbalance. Pore fluid densities and total adsorption isotherms increased monotonically with increasing density of the bulk fluid, in contrast to excess adsorption isotherms, which reached a maximum and then decreased toward zero or negative values above the critical density of the bulk fluid. The isotherms of confined fluid density and excess adsorption obtained by VTD contain additional information. For instance, the maxima of excess adsorption occur below the critical density of the bulk fluid at the beginning of the plateau region in the total adsorption, marking the end of the transition of pore fluid to a denser, liquidlike pore phase. Compression of the confined fluid significantly beyond the density of the bulk fluid at the same temperature was observed even at subcritical temperatures. The effect of pore confinement on the liquid-vapor critical temperature of propane was less than ~1.7 K. The results for propane and carbon dioxide showed similarity in the sense of the principle of corresponding states. Good quantitative agreement was obtained between excess adsorption isotherms determined from VTD total adsorption results and those measured gravimetrically at the same temperature, confirming the validity of the vibrating tube measurements. Thus, it is demonstrated that vibrating tube densimetry is a novel experimental approach capable of providing directly the average density of pore-confined fluids, and hence complementary to the conventional gravimetric or volumetric/piezometric adsorption techniques, which yield the excess adsorption (the Gibbsian surface excess).     

Temperature effects on nano-LC column packing technology

We investigated the effect of temperature on the packing procedure of nano-LC columns (up to 50 cm) and on their performance. Several slurries of stationary phase were prepared using different solvent mixtures. Their stability was evaluated at several temperatures: 70°C, 50°C, and room temperature. At the higher temperature (70°C) the suspensions resulted to be stable for a longer time. For each slurry, we compared nano-LC columns packed with ultrasounds at 70°C and at room temperature. All the columns were tested with a standard mixture at 70°C, to reduce the solvent viscosity and the backpressure. Main chromatographic parameters such as the asymmetry factor, As, the reduced plate high, h, pattern in a Van Deemter plot, the total porosity, ε(t), and the permeability, k, were calculated and discussed. One of the nano-LC columns was used to separate a mixture of pesticides in a LC-MS system with an electron ionization LC-MS interface (Direct-EI). From our knowledge, this is the first study on the role of temperature in the efficiency of slurry-packing procedure.     

Removal of Disperse Dyes from Water Using Surfactant Treated Alumina

An alumina surface was modified by adsorption of an anionic surfactant, sodium dodecyl sulfate (SDS). Typical S‐shaped isotherm of surfactant on alumina was observed. The adsorption of Disperse Red‐11, Disperse Blue‐26 and Disperse Red‐156 on alumina and surfactant treated alumina has been investigated. The enhancement in adsorption of these disperse dyes on surfactant treated alumina is observed, which may be attributed to their solubilization in surfactant aggregates formed at the solid/liquid interface. The effect of pH on adsorption has been studied. The adsorption is greatly influenced by pH of the medium. The applicability of the Langmuir model and the Dual‐Mode sorption model (DSM) were tested for equilibrium data.     

Adsorption of aerosol-OT to sapphire: lamellar structures studied with neutrons

The adsorption of sodium bis 2-ethylhexyl sulfosuccinate, NaAOT, to a sapphire surface from aqueous solution has been studied by neutron reflection at concentrations above the critical micelle concentration (cmc). Complementary measurements of the bulk structure were made with small-angle neutron scattering and grazing incidence small-angle neutron scattering. At a concentration of about 1% wt (10 × cmc), lamellar phase NaAOT was observed both at the surface and in the bulk. The structure seen at the interface for a solution of 2% wt NaAOT is a 35 ± 2 ? thick bilayer adsorbed to the sapphire surface at maximum packing density, followed by an aligned stack of fluctuating bilayers of thickness 51 ± 2 ? and with an area per molecule of 40 ± 2 ?(2). Each bilayer is separated by a water: at 25 °C, this layer is 148 ± 2 ?. A simple model for the reflectivity from fluctuating layers is presented, and for 2.0% wt NaAOT the fluctuations were found to have an amplitude of 25 ± 5 ?. The temperature sensitivity of the structure at the surface was investigated in the range 15-30 °C. The effect of temperature was pronounced, with the solvent layer becoming thinner and the volume occupied by the NaAOT molecules in a bilayer increasing with temperature. The amplitude of the fluctuations, however, is approximately temperature independent in this range. The adsorption of NaAOT at the sapphire surface resembles that previously found at hydrophilic and hydrophobic silica surfaces. The coexisting bulk lamellar phase has a spacing of layers similar to that observed at the surface. These observations are an indication that the major driving force for adsorption is self-assembly, independent of the chemical nature of the interface.     

Thermodynamic, spectroscopic, and computational studies of lanthanide complexation with diethylenetriaminepentaacetic acid: temperature effect and coordination modes

Stability constants of two DTPA (diethylenetriaminepentaacetic acid) complexes with lanthanides (ML(2-) and MHL(-), where M stands for Nd and Eu and L stands for diethylenetriaminepentaacetate) at 10, 25, 40, 55, and 70 °C were determined by potentiometry, absorption spectrophotometry, and luminescence spectroscopy. The enthalpies of complexation at 25 °C were determined by microcalorimetry. Thermodynamic data show that the complexation of Nd(3+) and Eu(3+) with DTPA is weakened at higher temperatures, a 10-fold decrease in the stability constants of ML(2-) and MHL(-) as the temperature is increased from 10 to 70 °C. The effect of temperature is consistent with the exothermic enthalpy of complexation directly measured by microcalorimetry. Results by luminescence spectroscopy and density functional theory (DFT) calculations suggest that DTPA is octa-dentate in both the EuL(2-) and EuHL(-) complexes and, for the first time, the coordination mode in the EuHL(-) complex was clarified by integration of the experimental data and DFT calculations. In the EuHL(-) complex, the Eu is coordinated by an octa-dentate H(DTPA) ligand and a water molecule, and the protonation occurs on the oxygen of a carboxylate group.     

Influence of temperature on the adsorption of mellitic acid onto kaolinite

The adsorption of mellitic acid (benzene-1,2,3,4,5,6-hexacarboxylic acid) onto kaolinite was investigated at five temperatures between 10 and 70 degrees C. Mellitic acid adsorption increased with increasing temperature at low pH (below pH 5.5), but at higher pH, the effect of increasing temperature was to reduce the amount adsorbed. Potentiometric titrations were conducted, adsorption isotherms were measured over the same temperature range, and the data obtained were used in conjunction with adsorption edge and ATR-FTIR spectroscopic data to develop an extended constant capacitance surface complexation model of mellitic acid adsorption. A single set of reactions was used to model all data at the five temperatures studied. The model indicates that mellitic acid sorbs via outer-sphere complexation to surface hydroxyl (SOH) groups on the kaolinite surface rather than to permanent charge sites. The reactions proposed are SOH + L6- + 2H+ <-->[(SOH2)+(LH)5-]4- and SOH + L(6-) <--> [(SOH)(L)6-]6-. Thermodynamic parameters calculated from the temperature dependence of the equilibrium constants for these reactions indicate that the adsorption of mellitic acid onto kaolinite is accompanied by a large entropy increase.     

Wireless sensing determination of uranium(IV) based on its inhibitory effect on a catalytic precipitation reaction

The adsorption of Eu(III) on multiwalled carbon nanotubes (MWCNTs) as a function of pH, ionic strength and solid contents are studied by batch technique. The results indicate that the adsorption of Eu(III) on MWCNTs is strongly dependent on pH values, dependent on ionic strength at low pH values and independent of ionic strength at high pH values. Strong surface complexation and ion exchange contribute to the adsorption of Eu(III) on MWCNTs at low pH values, whereas surface complexation and surface precipitation are the main adsorption mechanism of Eu(III) on MWCNTs. The desorption of adsorbed Eu(III) from MWCNTs by adding HCl is also studied and the recycling use of MWCNTs in the removal of Eu(III) is investigated after the desorption of Eu(III) at low pH values. The results indicate that adsorbed Eu(III) can be easily desorbed from MWCNTs at low pH values, and MWCNTs can be repeatedly used to remove Eu(III) from aqueous solutions. MWCNTs are suitable material in the preconcentration and solidification of radionuclides from large volumes of aqueous solutions in nuclear waste management.     

Diffuse reflectance infrared Fourier transform study of NO(x) adsorption on CGO10 impregnated with K2O or BaO

In the present work diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy is applied to study the adsorption of NO(x) at 300-500 °C in different atmospheres on gadolinium-doped ceria (CGO), an important material in electrodes investigated for electrochemical NO(x) removal. Furthermore, the effect on the NO(x) adsorption when adding K(2)O or BaO to the CGO is investigated. The DRIFT study shows mainly the presence of nitrate species at 500 °C, whereas at lower temperature a diversity of adsorbed NO(x) species exists on the CGO. The presence of O(2) is shown to have a strong effect on the adsorption of NO, but no effect on the adsorption of NO(2). Addition of K(2)O and BaO dramatically affects the NO(x) adsorption and the results also show that the adsorbed NO(x) species are mobile and capable of changing adsorption state in the investigated temperature range.     

Kinetics and equilibrium parameters of Hg(II) adsorption on silica-dithizone

Sílica-dithizone (Sil-dtz) was synthesized and used to adsorb Hg(II) in solution at pH 6.0. Increasing the temperature accelerates the mass transfer of Hg(II) to the silica surface. The kinetic data were evaluated using the traditional pseudo-first-order Lagergren equation and an alternative Avrami kinetic equation. From the latter equation, two regions presenting distinct kinetic parameters were found, at 25 and 35 degrees C, and the use of the parameter n was also related to the determination of distinct kinetic orders. Variations of the adsorption kinetic rate in relation to the time and the temperature were also calculated and are discussed. The adsorption isotherms data were well fitted to the Freundlich model. Interestingly, good adsorption data correlation of the Langmuir model and experimental values was observed only at 45 and 50 degrees C, suggesting, for this temperature range, the formation of complexes with the proportion Hg:dithizone 1:1 on the silica surface.