Prussian Blue/Reduced Graphene Oxide Composite for the Amperometric Determination of Dopamine and Hydrogen Peroxide

Prussian blue has significant application for the construction of electrochemical biosensors. In this work, Prussian blue-reduced graphene oxide modified glass carbon electrodes were successfully fabricated using electrochemical deposition. The high surface area of graphene oxide enhanced the deposition of Prussian blue and the resulting electrocatalytic activity. Infrared spectroscopy and scanning electron microscopy showed that the relatively porous Prussian blue was on the surface of reduced graphene oxide. Cyclic voltammetry showed that Prussian blue-coated reduced graphene oxide composite films improved electron transfer compared to Prussian blue films. The Prussian blue-reduced graphene oxide composite film provided higher response for the reduction of hydrogen peroxide and the oxidation of dopamine compared with the Prussian blue film due to synergistic effects between the reduced graphene oxide and Prussian blue particles. The sensitivity of the electrode was 0.1617 µA µM^?1 cm^?2. The linear dynamic range extended from 0.5 µM to 0.7 mM dopamine with a limit of detection equal to 125 nM. This work provided a versatile strategy for the design and construction of sensitive amperometric sensors with robust electrocatalytic behavior.     

Chitin/graphene oxide composite films with enhanced mechanical properties prepared in NaOH/urea aqueous solution

Chitin/graphene oxide (GO) composite films with excellent mechanical properties were prepared in NaOH/urea solution using a freezing/thawing method. The structure, thermal stability and mechanical properties of the composite films were investigated. Use of an atomic force microscope and transmission electron microscopy indicated that GO was successfully exfoliated to a single layer by ultrasonication. The results revealed that GO nanosheets were homogeneously dispersed and embedded in the chitin matrix. Due to the strong interactions between GO and the chitin matrix, the tensile strength and elongation at break of the composite film possessing 1.64 wt% GO were significantly improved by 98.7 and 114.5 %, respectively, compared with pure chitin film.     

LDPE/EVA/graphene nanocomposites with enhanced mechanical and gas permeability properties

In the present work, graphene oxide (GO) and reduced graphene oxide (RGO) were incorporated at low‐density polyethylene (LDPE)/ethylene vinyl acetate (EVA) copolymer blend using solution casting method. Monolayer GO with 1‐nm thickness and good transparency was synthesized using the well‐known Hummers's method. Fourier transform infrared and X‐ray photoelectron spectroscopy data exhibited efficient reduction of GO with almost high C/O ratio of RGO. Scanning electron microscopy showed the well distribution of GO and RGO within LDPE/EVA polymer matrix. The integrating effects of GO and RGO on mechanical and gas permeability of prepared films were examined. Young's modulus of nanocomposites are improved 65% and 92% by adding 7 wt% of GO and RGO, respectively. The tensile measurements showed that maximum tensile strength emerged in 3 wt% of loading for RGO and 5 wt% for GO. The measured oxygen and carbon dioxide permeability represented noticeably the attenuation of gas permeability in composite films compared with pristine LDPE/EVA blend. Copyright © 2015 John Wiley & Sons, Ltd.     

Properties of poly(acrylamide)/TEMPO-oxidized cellulose nanofibril composite films

Self-standing composite films consisting of 2,2,6,6-tetramethylpiperidine-1-oxyl-oxidized cellulose nanofibril (TOCN) and anionic poly(acrylamide) (PAM) in various weight ratios were prepared by casting and drying of homogeneous mixtures of aqueous TOCN dispersion and PAM solution. PAM/TOCN composite films consisting of 25 % PAM and 75 % TOCN had clearly higher Young’s modulus (13.9 GPa) and tensile strength (266 MPa) than 100 % TOCN film (10.8 GPa and 223 MPa, respectively) or 100 % PAM film (4.9 GPa and 78 MPa, respectively), showing that PAM molecules have mechanical reinforcement ability in TOCN matrix. Some attractive interactions are likely formed between TOCN element surfaces and PAM molecules. In contrast, no such mechanical improvements were observed for poly(vinyl alcohol)/TOCN or oxidized starch/TOCN composite films prepared as references. Moreover, the mechanical properties of the PAM/TOCN composite films were further improved by controlling molecular mass and branching degree of the PAM. The high optical transparency and low coefficient of thermal expansion of the 100 % TOCN film were mostly maintained in the TOCN composite film containing 25 % PAM.     

Physical and mechanical properties of graphene oxide/polyethersulfone nanocomposites

The aim of this study was to investigate physical and mechanical properties of graphene oxide (GO)/polyethersulfone (PES) nanocomposite films. The films were produced by solution casting method. The mechanical properties of composite films were evaluated by tensile test. A significant enhancement in the mechanical properties of neat PES films was obtained incorporating a small amount of GO loading (0.05–1 wt.%). The highest tensile strength was observed at 1 wt.% of GO. Comparisons were made between experimental data and the Halpin–Tsai model predictions for the tensile strength and modulus of GO/PES composites. The effect of an orientation factor on model predictions was also acquired. The hydrophilicity of the nanocomposite was evaluated by assessing contact angle and enhanced wet ability of the films was obtained with increasing the amount of GO up to 1%. The morphology of the nanocomposites was investigated using scanning electron microscopy and transmission electron microscopy and the results revealed a good dispersion of GO in the PES matrix. The thermal behavior of the composite was also studied. Thermal stability of composites was increased by adding the GO. Copyright © 2013 John Wiley & Sons, Ltd.     

Preparation of porous polyimide/in‐situ reduced graphene oxide composite films for electromagnetic interference shielding

Herein we report an easy and efficient approach to prepare lightweight porous polyimide (PI)/reduced graphene oxide (RGO) composite films. First, porous poly (amic acid) (PAA)/graphene oxide (GO) composite films were prepared via non‐solvent induced phase separation (NIPS) process. Afterwards PAA was converted into PI through thermal imidization and simultaneously GO dispersed in PAA matrix was in situ thermally reduced to RGO. The GO undergoing the same thermal treatment process as thermal imidization was characterized with thermogravimetric analysis, Raman spectra, X‐ray photoelectron spectroscopy and X‐ray diffraction to demonstrate that GO was in situ reduced during thermal imidization process. The resultant porous PI/RGO composite film (500‐µm thickness), which was prepared from pristine PAA/GO composite with 8 wt% GO, exhibited effective electrical conductivity of 0.015 S m^?1 and excellent specific shielding efficiency value of 693 dB cm² g^?1. In addition, the thermal stability of the porous PI/RGO composite films was also dramatically enhanced. Compared with that of porous PI film, the 5% weight loss temperature of the composite film mentioned above was improved from 525°C to 538°C. Moreover, tensile test showed that the composite film mentioned above possessed a tensile strength of 6.97 MPa and Young's modulus of 545 MPa, respectively. Copyright © 2016 John Wiley & Sons, Ltd.     

Enhanced toughness and strength of conductive cellulose-poly(butylene succinate) films filled with multiwalled carbon nanotubes

Cellulose (CE) composite films with high tensile strength, modulus, remarkable elongation as well as excellent electrical conductivity were successfully prepared by dispersing poly(butylene succinate) (PBS) and multiwalled carbon nanotubes (MWCNTs) in CE matrix via the help of ionic liquid 1-allyl-3-methylimidazolium chloride. Fourier transform infrared spectroscopy and differential scanning calorimetry results verified that a physical interaction junction existed between PBS and CE. Scanning electron micrograph (SEM) showed that the low content PBS was uniformly dispersed in CE matrix, leading to a tough and ductile fractured surface. The elongation at break of CE composite film with 1 wt% PBS was increased to 25.9 %, which showed an increase of 325 % compared to that of neat CE film (6.07 %). But high-content PBS acted as the structural defect in the CE matrix. MWCNTs were further added to improve the mechanical and conductive properties of the composite film. The tensile strength and Young’s modulus of MWCNT/CE-PBS composite film with 4 wt% MWCNTs were respectively increased by 33.6 and 140 % compared to CE-PBS film. The electrical conductivity of MWCNT/CE-PBS film was also improved by 8–9 orders of magnitude from 2.5 × 10^?14 to 1.3 × 10^?5 S/m.     

Nanocrystalline cellulose acetate (NCCA)/graphene oxide (GO) nanocomposites with enhanced mechanical properties and barrier against water vapor

Highly flexible nanocomposite films of nanocrystalline cellulose acetate (NCCA) and graphene oxide (GO) were synthesized by combining NCCA and GO sheets in a well-controlled manner. By adjusting the GO content, various NCCA/GO nanocomposites with 0.3–1 wt% GO were obtained. Films of these nanocomposites were prepared using the solvent casting method. Microscopic and X-ray diffraction (XRD) measurements demonstrated that the GO nanosheets were uniformly dispersed in the NCCA matrix. Mechanical properties of the composite films were also studied. The best GO composition of the samples tested was 0.8 wt%, giving tensile strength of 157.49 MPa, which represents a 61.92 % enhancement compared with NCCA. On the other hand, the composite films showed improved barrier properties against water vapor. This simple process for preparation of NCCA/GO films is attractive for potential development of high-performance films for electrical and electrochemical applications.     

Preparation of cellulose-based fluorescent materials using Zinc sulphide quantum dot-decorated graphene by a one-step hydrothermal method

Cellulose-based fluorescent materials using Zinc sulphide (ZnS) quantum dot-decorated graphene were prepared by a one-step hydrothermal method. X-ray photoelectron spectroscopy analysis identified the chemical states of Zn, S, C, O, and N in the composite paper. Transmission electron microscopy showed that the graphite oxide was reduced to graphene sheets, and ZnS nanoparticles (<10 nm) were deposited on the surface of these sheets. Scanning electron microscopy indicated that graphene sheets were attached to the surface of paper fibers, and the paper structure and morphology of the fibers were not observably damaged during the hydrothermal reaction. The cellulose-based composite had strong ultraviolet absorption in the range of 200–340 nm, and its main absorption peak was at approximately 296 nm. The band edge emission of photoluminescence spectrum of the composite occurred at 466 nm with an excitation wavelength of 320 nm. The laser scanning confocal microscope image of the composite exhibited an intense blue fluorescence under UV light at 405 nm.     

Mechanical properties and degradation studies of poly(D,L‐lactide‐co‐glycolide) 50:50/graphene oxide nanocomposite films

Poly(D,L‐lactide‐co‐glycolide) 50:50 (PLGA)/graphene oxide (GO) nanocomposite films were prepared with various GO weight fractions. A significant enhancement of mechanical properties of the PLGA/GO nanocomposite films was obtained with GO weight fractions. The incorporation of only 5 wt% of GO resulted in an ~2.5‐fold and ~4.7‐fold increase in the tensile strength and Young's modulus of PLGA, respectively. The thermomechanical behaviors of composite films were investigated by dynamic mechanical analysis. Results indicated that the values of T_g and storage moduli of the PLGA/GO composites were higher than those of the pristine PLGA. The improvement in oxygen barrier properties of composites was presumably attributed to the filler effect of the randomly dispersed GO throughout the PLGA matrix. In this work, we also studied in vitro biodegradation behavior. PLGA/GO composite films were hydrolyzed at 37°C for periods up to 49 days. Because of the presence of GO nanosheets, degradation of composite films took place more slowly with increasing GO amounts. Copyright © 2013 John Wiley & Sons, Ltd.     

Enhancement of mechanical properties of natural rubber with maleic anhydride grafted liquid polybutadiene functionalized graphene oxide

An effective procedure has been developed to synthesize the functionalized graphene oxide grafted by maleic anhydride grafted liquid polybutadiene(MLPB-GO). Fourier transform spectroscopy and X-ray photoelectron spectroscopy indicate the successful functionalization of GO. The NR/MLPB-GO composites were then prepared by the co-coagulation process. The results show that the mechanical properties of NR/MLPB-GO composites are obviously superior to those of NR/GO composites and neat NR. Compared with neat NR, the tensile strength, modulus at 300% strain and tear strength of NR composite containing 2.12 phr MLPB-GO are significantly increased by 40.5%, 109.1% and 85.0%, respectively. Dynamic mechanical analysis results show that 84% increase in storage modulus and 2.9 K enhancement in the glass transition temperature of the composite have been achieved with the incorporation of 2.12 phr MLPB-GO into NR. The good dispersion of GO and the strong interface interaction in the composites are responsible for the unprecedented reinforcing efficiency of MLPB-GO towards NR.     

Influence of high loading of cellulose nanocrystals in polyacrylonitrile composite films

Polyacrylonitrile-co-methacrylic acid (PAN-co-MAA) and cellulose nanocrystal (CNC) composite films were produced with up to 40 wt% CNC loading through the solution casting method. The rheological properties of the solution/suspensions and the structural, optical, thermal, and mechanical properties of the resulting films were investigated. The viscosity of the composite suspensions increased with higher CNC loadings and with longer aging times. PAN-co-MAA/CNC films maintained a similar level of optical transparency even with up to 40 wt% CNC loading. The glass transition temperature (Tg) increased from 92 to 118 °C, and the composites had higher thermal stability below 350 °C compared to both neat PAN-co-MAA and neat CNC. The mechanical properties also increased with higher CNC loadings, elastic modulus increased from 2.2 to 3.7 GPa, tensile strength increased from 75 to 132 MPa, and the storage modulus increased from 3.9 to 10.5 GPa. Using the Kelly and Tyson model the interfacial shear strength between the PAN-co-MAA and CNC was calculated to be 27 MPa.     

Preparation and characterization of corn starch/soy protein biocomposite film reinforced with graphene and graphene oxide nanoplatelets

Corn starch (CS) and soy protein isolate (SPI), as inexpensive, abundant, and biodegradable materials, can chemically interact well with each other to produce biofilms. However, to overcome some of their physical and mechanical limitations, it is preferred to use their composite form, employing reinforcing materials. In this study, initially, graphene (G) and graphene oxide (GO) were synthesized by a green method. Then, to enhance the polymer blend final properties, the effects of adding G and GO in the range of 0.5 to 2 wt% on physical and mechanical properties of starch/protein blend were investigated. The results showed that the presence of 0.5‐wt% G and 2‐wt% GO significantly increased the modulus of starch/protein film from 252 to 578 and 449 MPa, respectively. In addition, the thermal stability of CS/SPI/GO (2 wt%) composite film was 50°C to 60°C more than that of the pure starch/protein film. On the other hand, G‐reinforced composite films tended to decline water diffusion compared with the pure polymer film. In addition, the composite film with 2‐wt% GO content had the lowest oxygen permeation rate (3.48 cm³ μm/m²d kpa) among the other composite films.     

Synthesis and characterization of <Emphasis Type="Italic">β</Emphasis>-cyclodextrin–carboxymethyl cellulose–graphene oxide composite materials and its application for removal of basic fuchsin

A novel β-cyclodextrin–carboxymethyl cellulose–graphene oxide composite material (β-CD–CMC–GO) was synthesized, and its application as excellent adsorbents was carried out for removal basic fuchsin (BF) in aqueous solution. The structure and morphology of β-CD–CMC–GO composite material were characterized by using FTIR, SEM, TEM, XRD, TG and DSC methods. The composites could remove basic fuchsin from aqueous solution efficiently. The adsorption experiment was carried out and the optimum experimental conditions were ascertained. The highest adsorption efficiency was obtained 97.3% at 0.015 g/mL dosage of β-CD–CMC–GO, the temperature of 25 °C and time of 2.5 h. Adsorption kinetics, adsorption isotherm and adsorption thermodynamic were used to analyze the adsorption system. The experimental data of adsorption kinetics of system were well followed by pseudo-second-order equation. The adsorption isotherm data were fitted using Langmuir isotherm model and Freundlich isotherm model. The maximum adsorption capacity of basic fuchsin reached 58.65 mg/g. The thermodynamic parameters indicated that the adsorption process was spontaneous and exothermic. The adsorbent has excellent regeneration ability and reproducibility. The proposed method shows that the β-CD–CMC–GO could be applied to removal of basic fuchsin in wastewater with satisfactory result.     

Effect of the C/O ratio in graphene oxide materials on the reinforcement of epoxy-based nanocomposites

The effect of the C/O ratio of graphene oxide materials on the reinforcement and rheological percolation of epoxy-based nanocomposites has been studied. As-prepared graphene oxide (GO) and thermally-reduced graphene oxide (TRGO) with higher C/O ratios were incorporated into an epoxy resin matrix at loadings from 0.5 to 5 wt %. Tensile testing revealed good reinforcement of the polymer up to optimal loadings of 1 wt %, whereas agglomeration of the flakes at higher loadings caused the mechanical properties of the composites to deteriorate. The level of reduction (C/O) of the graphene oxide filler was found to influence the mechanical and rheological properties of the epoxy composites. Higher oxygen contents were found to lead to stronger interfaces between graphene and epoxy, giving rise to higher effective Young's moduli of the filler and thus to superior mechanical properties of the composite. The effective modulus of the GO in the nanocomposites was found to be up to 170 GPa. Furthermore, rheological analysis showed that highly oxidized graphene flakes did not raise the viscosity of the epoxy resin significantly, facilitating the processing considerably, of great importance for the development of these functional polymeric materials. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 281–291     

Direct covalent modification of thermally exfoliated graphene forming functionalized graphene stably dispersible in water and poly(vinyl alcohol)

The syntheses of water-dispersible graphene via graphene oxide colloid dispersion and/or using functionalizations that disrupt the π-bond system of graphene or contaminate a graphene surface with big amounts of undesired impurities face some challenges in practical applications. Approaches based on thermally exfoliated graphene might be promising for many applications in which flat and perfect single-layer graphene is not mandatory and productivity is more than important. In this paper, for the first time, we report a simple and effective method to prepare water-dispersible graphene directly from thermally exfoliated graphene by covalent modification utilizing the inherent defects of graphene as active sites. That is, the epoxide groups on graphene were reacted with ethanolamine and then with n-butyl bromide to prepare the graphene decorated with cationic ammonium ions (alkylated graphene, AAG). Elemental analysis, thermogravimetry, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy demonstrated that the reactions have proceeded as designed. The Raman spectra showed that the π-electronic system of sp ²-bonded carbons of the graphene was not damaged by the modification. The homogeneous colloidal dispersion of AAG in water remained stable for at least 6 months, showing that the wrinkled nature of the graphene as well as the electrostatic repulsion and steric hindrance between the graphene sheets caused by the bulky ammonium moieties on the graphene’s surface efficiently prevented the graphene from restacking and aggregating. The AAG dispersed stably in a poly(vinyl alcohol) matrix produced an extraordinarily high modulus increase of 236 % with just 1 phr (about 0.5 vol%) of AAG.     

Preparing graphene oxide–copper composite material from spent lithium ion batteries and catalytic performance analysis

The wide use of lithium ion batteries (LIBs) has created much waste, which has become a global issue. It is vital to recycle waste LIBs considering their environmental risks and resource characteristics. Anode graphite from spent LIBs still possess a complete layer structure and contain some oxygen-containing groups between layers, which can be reused to prepare high value-added products. Given the intrinsic defect structure of anode graphite, copper foils in LIB anode electrodes, and excellent properties of graphene, graphene oxide–copper composite material was prepared in this work. Anode graphite was firstly purified to remove organic impurities by calcination and remove lithium. Purified graphite was used to prepare graphene oxide–copper composite material after oxidation to graphite oxide, ultrasonic exfoliation to graphene oxide (GO), and Cu²⁺ adsorption. Compared with natural graphite, preparing graphite oxide using anode graphite consumed 40% less concentrated H₂SO₄ and 28.6% less KMnO₄. Cu²⁺ was well adsorbed by 1.0 mg L^?1 stable GO suspension at pH 5.3 for 120 min. Graphene oxide–copper composite material could be successfully obtained after 6 h absorption, 3 h bonding between GO and Cu²⁺ with 3/100 of GO/CuSO₄ mass ratio. Compared to CuO, graphene oxide–copper composite material had better catalytic photodegradation performance on methylene blue, and the electric field further improved the photodegradation efficiency of the composite material.     

Preparation of superhydrophobic electroconductive graphene-coated cotton cellulose

A simple and versatile method based on cotton cellulose coated with graphene is reported for the fabrication of superhydrophobic and electroconductive textiles. Graphene oxide was deposited on cotton fibers by a dip-pad-dry method followed by reduction with ascorbic acid to yield a fabric with a layer of graphene. The fabric was then reacted with methyltrichlorosilane to form polymethylsiloxane (PMS) nanofilaments on the fibers surface. The surface chemistry and morphology were characterized by UV–visible reflectance spectrophotometry, Fourier transform infrared spectroscopy, energy-dispersive X-ray spectroscopy and scanning electron microscopy. The water contact angle (CA)/shedding angle (SHA) and resistivity measurements were used for assessing hydrophobicity and conductivity, respectively. The graphene-coated fabric showed hydrophobicity with the CA of 143.2° ± 2.9° and SHA of 41°. The formation of PMS nanofilaments displayed superhydrophobicity with CA of 163° ± 3.4° and SHA of 7°, which indicated the self-cleaning ability. Conductivity of the graphene-coated fabric was confirmed by the electrical resistivity of 91.8 kΩ/sq which increased to 112.5 kΩ/sq after the formation of PMS nanofilaments.     

Good electrical and mechanical properties induced by the multilayer graphene oxide sheets incorporated to amorphous carbon films

Multilayer graphene oxide nanosheets were fabricated using commercially available expanded graphite by simple ultrasonic treatment and then were incorporated into the amorphous carbon matrix as fillers by electrochemical deposition. The electrical conductivity of the films was strongly improved due to the contribution of the multilayer graphene oxide sheets. Moreover, the Young’s modulus, hardness and elastic recovery of the composite films were measured to be about 171.1 GPa, 10.1 GPa and 81.4%, respectively, compared to 137.4 GPa, 5.1 GPa and 44.3% of undoped a-C:H films prepared at the same conditions. Additionally, the friction coefficient was tested to be 0.15 (0.5 N, 2 Hz) and the antiwear life was prolonged to about 200 s while the undoped DLC films obtained at the same condition were easy to be frazzled.     

Preparation and property assessment of neat lignocellulose nanofibrils (LCNF) and their composite films

Lignocellulose nanofibrils (LCNF) were produced from thermo-mechanical pulp (TMP) using a micro-grinder and were characterized with respect to fiber diameter and thermal stability. The initial water content in the TMP affected the defibrillation process and longer grinding time was necessary for the air-dried TMP, resulting in LCNF with higher fibril diameter. As compared to the reference cellulose nanofibrils (CNF) produced through a refining process, LCNF was less thermally stable and started to degrade at a temperature that was 30 °C lower than that of CNF. LCNF obtained from the never-dried TMP was combined with various additives (10 wt%) to produce composite films. The neat LCNF and composite films did not reach the mechanical properties of the neat CNF film that was evaluated as reference. However, the addition of poly(vinyl alcohol) (PVA) at 10 wt% on a dry basis did cause a 46 and 25% increase in tensile strength and elastic modulus, respectively. Other additives including cellulose nanocrystals, bentonite and CNF were also found to increase to some extent the Young’s modulus and ductility of the LCNF composite films whereas the addition of talc did not improve the film performance. Water absorption of neat LCNF films was lower than the reference CNF and was negatively affected by the addition of PVA.