不同基材上TiO2膜的表征和光催化活性评价

 采用溶胶-凝胶法在平行条件下制备了负载于钛、铝、不锈钢和玻璃等不同基材上的TiO2浸渍提拉膜,利用原子力显微镜、俄歇电子能谱、X射线衍射、漫反射紫外-可见光谱和苯甲酰胺光催化降解等手段对TiO2膜进行了表征和催化活性评价. 实验结果表明,基材的种类对TiO2膜的性能有较大影响,各膜样品虽均为锐钛矿晶型,但表面形貌显著不同. TiO2/Ti, TiO2/steel, TiO2/Al和TiO2/glass上TiO2的平均粒径分别是152, 205, 241和477 nm,且前两者的粒径分布较为集中. TiO2/Ti和TiO2/Al样品表面仅有Ti和O元素存在,而TiO2/steel和TiO2/glass表面则分别检测到有Fe和Na,Ca及Si等基材元素渗出. 各膜样品对苯甲酰胺光催化降解的活性次序是:TiO2/Ti＞TiO2/Al＞TiO2/glass＞TiO2/steel. 根据实验结果可以推测,在焙烧阶段各基材上前驱体膜烧结行为的不同以及基材元素的渗出是造成不同基材上的TiO2膜在表面形貌、化学组成、光吸收性能以及光催化活性方面存在明显差异的主要原因.     

Kinetics of heterogeneous photocatalytic degradation of reactive dyes in an immobilized TiO2 photocatalytic reactor

The photocatalytic degradation of two reactive dyes has been investigated by UV/TiO2/H2O2 using an immobilized TiO2 photocatalytic reactor. Reactive Blue 8 (RB 8) and Reactive Blue 220 (RB 220) textile dyes were used as model compounds. Photocatalytic degradation processes were performed using a 5-L solution containing dyes. The initial concentrations of dyes were 50 mg/L. The radiation source was two 15 W UV-C lamps. A batch mode immersion photocatalytic reactor was utilized. UV-vis and ion chromatography (IC) analyses were employed to obtain the details of the photodegradation of the selected dyes. Colored synthetic waters were completely decolorized in relatively short time after UV irradiation in the presence of various concentrations of hydrogen peroxide. Formate, acetate, oxalate, and glyoxylate anions were detected as dominant aliphatic intermediates where they were further oxidized slowly to CO2. The UV/TiO2/H2O2 process was able to oxidize the dyes with partial mineralization of carbon, nitrogen, and sulfur heteroatoms into CO2, NO3-, and SO4(2-), respectively. Kinetics analysis indicates that the photocatalytic decolorization rates of the dye can be approximated by a pseudo-first-order model. The UV/TiO2/H2O2 process proved to be capable of decolorization and mineralization of the reactive dyes (RB 8 and RB 220).     

Control of charge recombination dynamics in dye sensitized solar cells by the use of conformally deposited metal oxide blocking layers

We report herein a methodology for conformally coating nanocrystalline TiO2 films with a thin overlayer of a second metal oxide. SiO2, Al2O3, and ZrO2 overlayers were fabricated by dipping mesoporous, nanocrystalline TiO2 films in organic solutions of their respective alkoxides, followed by sintering at 435 degrees C. These three metal oxide overlayers are shown in all cases to act as barrier layers for interfacial electron transfer processes. However, experimental measurements of film electron density and interfacial charge recombination dynamics under applied negative bias were vary significantly for the overlayers. A good correlation was observed between these observations and the point of zero charge of the different metal oxides. On this basis, it is found that the most basic overlayer coating, Al2O3 (pzc = 9.2), is optimal for retarding interfacial recombination losses under negative applied bias. These observations show good correlation with current/voltage analyses of dye sensitized solar cell fabricated from these films, with the Al2O3 resulting in an increase in V(oc) of up to 50 mV and a 35% improvement in overall device efficiency. These observations are discussed and compared with an alternative TiCl4 posttreatment of nanocrystalline TiO2 films with regard to optimizing device efficiency.     

Influence of surface-attachment functionality on the aggregation, persistence, and electron-transfer reactivity of chalcogenorhodamine dyes on TiO2

Chalcogenorhodamine dyes bearing phosphonic acids and carboxylic acids were compared as sensitizers of nanocrystalline TiO(2) in dye-sensitized solar cells (DSSCs). The dyes were constructed around a 3,6-bis(dimethylamino)chalcogenoxanthylium core and varied in the 9 substituent: 5-carboxythien-2-yl in dyes 1-E (E = O, Se), 4-carboxyphenyl in dyes 2-E (E = O, S), 5-phosphonothien-2-yl in dyes 3-E (E = O, Se), and 4-phosphonophenyl in dyes 4-E (E = O, Se). All dyes adsorbed to TiO(2) as mixtures of H aggregates and monomers, which exhibited broadened absorption spectra relative to those of purely amorphous monolayers. Surface coverages of dyes and the extent of H aggregation varied minimally with the surface-attachment functionality, the structure of the 9-aryl group, and the identity of the chalcogen heteroatom. Carboxylic acid-functionalized dyes 1-E and 2-E desorbed rapidly and completely from TiO(2) into acidified CH(3)CN, but phosphonic acid-functionalized dyes 3-E and 4-E persisted on TiO(2) for days. Short-circuit photocurrent action spectra of DSSCs corresponded closely to the absorptance spectra of dye-functionalized films; thus, H aggregation did not decrease the electron-injection yield or charge-collection efficiency. Maximum monochromatic incident photon-to-current efficiencies (IPCEs) of DSSCs ranged from 53 to 95% and were slightly higher for carboxylic acid-functionalized dyes 1-E and 2-E. Power-conversion efficiencies of DSSCs under white-light illumination were low (<1%), suggesting that dye regeneration was inefficient at high light intensities. The photoelectrochemical performance (under monochromatic or white-light illumination) of 1-E and 2-E decayed significantly within 20-80 min of the assembly of DSSCs, primarily because of the desorption of the dyes. In contrast, the performance of phosphonic acid-functionalized dyes remained stable or improved slightly on similar timescales. Thus, replacing carboxylic acids with phosphonic acids increased the inertness of chalcogenorhodamine-TiO(2) interfaces without greatly impacting the aggregation of dyes or the interfacial electron-transfer reactivity.     

Fabrication and photocatalytic characterizations of ordered nanoporous X-doped (X = N, C, S, Ru, Te, and Si) TiO2/Al2O3 films on ITO/glass

Transparent, ordered nanoporous TiO2/Al2O3 composite films doped with metal elements (Ru, Si, and Te) and nonmetal elements (N, C, and S) were fabricated by successive anodization and sol-gel process directly on glass substrates covered with a tin-doped indium oxide (ITO) film. The doping of ruthenium, nitrogen, carbon, and sulfur in TiO2 exhibited an enhanced effect on the absorbance, while the doping of silicon and tellurium showed little effect. Particularly, the N- and Ru-doped TiO2/Al2O3 films on ITO/glass developed an enhanced absorption red shift of 580 nm (-N) and 500 nm (-Ru). The nanoporous TiO2/Al2O3 composite film exhibited the highest photocatalytic activity in decomposing acetaldehyde under ultraviolet-light irradiation, with a value of 13 times in initial reaction rate or 7.8 times in quantum yield higher than a commercially available TiO2 material, Degussa P25. The ultraviolet-light photocatalytic activities of nanoporous TiO2/Al2O3 films were enhanced by the doping of nitrogen, carbon, and sulfur but slightly weakened by the doping of ruthenium, silicon, and tellurium. Particularly, the nanoporous N-doped TiO2/Al2O3 films exhibited effective photocatalytic activity on ultraviolet light decomposition of a highly toxic dioxin, HpCDD, and gave the highest decomposition rate of approximately 95% (via 7 h of irradiation) for the specimen with a dopant content of 1.7 wt % nitrogen.     

Effect of supporting surface layers on catalytic activities of gold nanoparticles in CO oxidation

The surfaces of fumed silica materials were modified with a surface sol-gel process for catalysis applications. This surface-modification approach allows not only a monolayer growth of TiO(2) or Al(2)O(3) but also a stepwise double-layer growth of TiO(2)/TiO(2), Al(2)O(3)/Al(2)O(3), TiO(2)/Al(2)O(3), or Al(2)O(3)/TiO(2) on the surfaces of the silica materials with a monolayer precision. XRD analyses revealed that the coated monolayers and double layers of TiO(2) and Al(2)O(3) were amorphous. Gold nanoparticles were successfully deposited on the above six surface-modified silica materials via a deposition-precipitation method. The catalytic activities of these six gold catalysts for CO oxidation are highly dependent on the structures of their surface monolayers or double layers. The gold catalyst supported on the silica material functionalized with a TiO(2) monolayer (Au/TiO(2)) is the most active in both as-synthesized and oxidized forms, while the gold catalyst supported on the silica material functionalized with an Al(2)O(3)/TiO(2) double layer (Au/Al(2)O(3)/TiO(2)/SiO(2)) is the most active in the reduced form among the six catalysts. Surprisingly, the gold catalyst supported on the silica material functionalized with a TiO(2)/Al(2)O(3) double layer (Au/TiO(2)/Al(2)O(3)/SiO(2)) has much less activity than Au/Al(2)O(3)/TiO(2)/SiO(2) under all various treatments, underscoring the sensitivity of the catalytic activity to the structure of the supporting surfaces.     

Spectroelectrochemical studies of hole percolation on functionalised nanocrystalline TiO2 films: a comparison of two different ruthenium complexes

We report the application of spectroelectrochemical techniques to compare the hole percolation dynamics of molecular networks of two ruthenium bipyridyl complexes adsorbed onto mesoporous, nanocrystalline TiO(2) films. The percolation dynamics of the ruthenium complex cis-di(thiocyanato)(2,2'-bipyridyl-4,4'-dicarboxylic acid)-(2,2'-bipyridyl-4,4'-tridecyl) ruthenium(II), N621, is compared with those observed for an analogous dye with an additional tri-phenyl amine (TPA) donor moiety, cis-di(thiocyanato)(2,2'-bipyridyl-4,4'-dicarboxylic acid)-(2,2'-bipyridyl-4,4'-bis(vinyltriphenylamine)) ruthenium(II), HW456. The in situ oxidation of these ruthenium complexes adsorbed to the TiO(2) films is monitored by cyclic voltammetry and voltabsorptometry, whilst the dynamics of hole (cation) percolation between adsorbed ruthenium complexes is monitored by potentiometric spectroelectrochemistry and chronoabsorptometry. The hole diffusion coefficient, D(eff), is shown to be dependent on the dye loading on the nanocrystalline TiO(2) film, with a threshold observed at ～60% monolayer surface coverage for both dyes. The hole diffusion coefficient of HW456 is estimated to be 2.6 × 10(-8) cm(2)/s, 20-fold higher than that obtained for the control N621, attributed to stronger electronic coupling between the TPA moieties of HW456 accelerating the hole percolation dynamics. The presence of mercuric ions, previously shown to bind to the thiocyanates of analogous ruthenium complexes, resulted in a quenching of the hole percolation for N621/TiO(2) films and an enhancement for HW456/TiO(2) films. These results strongly suggest that the hole percolation pathway is along the overlapped neighbouring -NCS groups for the N621 molecules, whereas in HW456 molecules cation percolation proceeds between intermolecular TPA ligands. These results are discussed in the context of their relevance to the process of dye regeneration in dye sensitised solar cells, and to the molecular wiring of wide bandgap inorganic materials for battery and sensing applications.     

Preillumination of TiO2 and Ta2O5 photoactive thin films as a tool to tailor the synthesis of composite materials

Illumination of TiO 2 thin films with UV light is known to induce the transformation of the surface of this material from partially hydrophobic into fully hydrophilic. The present work shows that this transformation is accompanied by other effects that may be used to control the synthesis of composite materials. For this purpose, TiO 2 and Ta 2O 5 transparent thin films with a columnar structure and open pores were prepared by electron evaporation at glancing angles. Transparent TiO 2 thin films with micropores (i.e., pores smaller than 2 nm) prepared by plasma enhanced chemical vapor deposition (PECVD) were also used. All these films became hydrophilic upon UV illumination. Rhodamine 6G and Rhodamine 800 dyes were irreversibly adsorbed within the columns of the TiO 2 and Ta 2O 5 thin films by immersion into a water solution of these molecules. Isolated and aggregated molecules of these two dyes were detected by visible absorption spectroscopy. The infiltration adsorption efficiency was directly correlated with the acidity of the medium, increasing at basic pHs as expected from simple considerations based on the concepts of the point of zero charge (PZC) in colloidal oxides. The infiltration experiments were repeated with columnar TiO 2 and Ta 2O 5 thin films that were subjected to preillumination with UV light. It was found that this treatment produced a modification in the type (isolated or aggregated) and amount of dye molecules incorporated into the pores. Moreover, the selective adsorption of a given dye in preilluminated areas of the films permitted the lithographic coloring of the films. Preillumination also controls the UV induced deposition of silver on the surface of the microporous TiO 2 thin films. It was found that the size distribution of the formed silver nanoparticles was dependent on the preillumination treatment and that a well-resolved surface plasmon resonance at around 500 nm was only monitored in the preilluminated films. A model is proposed to account for the effects induced by UV preillumination on the TiO 2 and Ta 2O 5 oxide surfaces. The possibilities of this type of light treatment for the tailored synthesis of nanocomposite thin films (i.e., dye-oxide, metal nanoparticles-oxide) are highlighted.     

载体对担载Ni催化剂甲烷与二氧化碳重整反应活性的影响

制备了 Zr O2 、Mg O改性的 Al2 O3、Ti O2 复合载体 ,并应用 X-射线粉末衍射 (XRD)、比表面积测定、扫描电镜 (SEM)等手段进行了表征 .结果表明 ,这些氧化物在 Al2 O3上的晶粒尺寸小、比表面积大 ,分散较好 ,而在Ti O2 上的分散性较差 .对经 10 73K焙烧的 Mg O/ Ti O2 ,还发现部分 Ti O2 载体由锐钛矿变为金红石 ,同时生成Mg Ti O3 新相 .考察了载体对 Ni催化剂的 CH4与 CO2 重整反应活性的影响 ,其次序为 :Mg O/ Al2 O3>Zr O2 /Al2 O3>Al2 O3>Mg O >Zr O2 >Ti O2 >Mg O/ Ti O2 . Ti O2 及 Mg O/ Ti O2 担载 Ni催化剂的低活性可能与 Ti O2 本身的还原性有关     

Mechanism of TiO2-assisted photocatalytic degradation of dyes under visible irradiation: photoelectrocatalytic study by TiO2-film electrodes

Photoelectrocatalytic degradation of various dyes under visible light irradiation with a TiO(2) nanoparticles electrode has been investigated to reveal the mechanism for TiO(2)-assisted photocatalytic degradation of dyes. The degradation of both cationic and anionic dyes at different biases, including the change in the degradation rate of the dyes and the photocurrent change with the bias potential, the degraded intermediates, the voltage-induced adsorption of dyes, the accumulation of electrons in the TiO(2) electrode, the effect of various additives such as benzoquinone (BQ) and N,N-dimethyl aniline (DMA), and the formation of active oxygen species such as O(2)(*-) and H(2)O(2) were examined by UV-visible spectroscopy, HPLC, TOC, and spin-trap ESR spectrometry. It was found that the dyes could controllably interact with the TiO(2) surface by external bias changes and charging of dyes. The cationic dyes such as RhB and MG underwent efficient mineralization at negative bias, but the N-dealkylation process predominated at positive bias under visible light irradiation. The discolorations of the anionic dyes SRB and AR could not be accelerated significantly at either negative or positive bias. At a negative bias of -0.6 V vs SCE, O(2)(*-) and dye(*+) were formed simultaneously at the electrode/electrolyte interface during degradation of cationic RhB. In the case of anionic dyes, however, it is impossible for the O(2)(*-) and dye cationic radical to coexist at the electrode/electrolyte surface. Experimental results imply both the superoxide anionic radical and the dye cationic radical are essential to the mineralization of the dyes under visible light-induced photocatalytic conditions.     

Electron injection dynamics of Ru polypyridyl complexes on SnO2 nanocrystalline thin films

Ultrafast infrared spectroscopy was utilized to investigate the electron-transfer dynamics from Ru(dcbpy)(2)(X)(2) complexes (dcbpy = 4,4'-dicarboxy-2,2'-bipyridine; X(2) = SCN(-), 2CN(-), and dcbpy; referenced as RuN3, Ru505, and Ru470, respectively) to nanocrystalline SnO(2) films. For both films exposed to air (dry) and submerged in a pH 2 buffer solution, all traces show biphasic dynamics with a small ultrafast component (less than 10%) and nonexponential slow component, indicating that most injection occurs from thermalized excited state of the dye. In the dry film, the injection rate becomes slower, comparing RuN3, Ru505, and Ru470, correlating with decreasing excited-state oxidation potentials in these dyes. However, the variation of injection rate with dye potential is less noticeable at pH 2. The possible reason for the different injection dynamics in these dyes and under different environments are discussed. These injection dynamics are also compared with those on TiO(2) and ZnO.     

Size and support effects for the water-gas shift catalysis over gold nanoparticles supported on model Al2O3 and TiO2

The water-gas shift (WGS) reaction rate per total mole of Au under 7% CO, 8.5% CO(2), 22% H(2)O, and 37% H(2) at 1 atm for Au/Al(2)O(3) catalysts at 180 °C and Au/TiO(2) catalysts at 120 °C varies with the number average Au particle size (d) as d(-2.2±0.2) and d(-2.7±0.1), respectively. The use of nonporous and crystalline, model Al(2)O(3) and TiO(2) supports allowed the imaging of the active catalyst and enabled a precise determination of the Au particle size distribution and particle shape using transmission electron microscopy (TEM). Further, the apparent reaction orders and the stretching frequency of CO adsorbed on Au(0) (near 2100 cm(-1)) determined by diffuse reflectance infrared spectroscopy (DRIFTS) depend on d. Because of the changes in reaction rates, kinetics, and the CO stretching frequency with number average Au particle size, it is determined that the dominant active sites are the low coordinated corner Au sites, which are 3 and 7 times more active than the perimeter Au sites for Au/Al(2)O(3) and Au/TiO(2) catalysts, respectively, and 10 times more active for Au on TiO(2) versus Al(2)O(3). From operando Fourier transform infrared spectroscopy (FTIR) experiments, it is determined that the active Au sites are metallic in nature. In addition, Au/Al(2)O(3) catalysts have a higher apparent H(2)O order (0.63) and lower apparent activation energy (9 kJ mol(-1)) than Au/TiO(2) catalysts with apparent H(2)O order of -0.42 to -0.21 and activation energy of 45-60 kJ mol(-1) at near 120 °C. From these data, we conclude that the support directly participates by activating H(2)O molecules.     

The adsorption and reaction of a titanate coupling reagent on the surfaces of different nanoparticles in supercritical CO2

The adsorption and reaction in supercritical CO2 of the titanate coupling reagent NDZ-201 on the surfaces of seven metal oxide particles, SiO2, Al2O3, ZrO2, TiO2 (anatase), TiO2 (rutile), Fe2O3, and Fe3O4, was investigated. FTIR and TG analysis indicated that the adsorption and reaction were different on different particle surfaces. On SiO2 and Al2O3 particles, there was a chemical reaction of the titanate coupling reagent on the surfaces. On the surfaces of ZrO2 and TiO2 (anatase) particles, there were two kinds of adsorption, weak and strong adsorption. On the surfaces of TiO2 (rutile), Fe2O3, and Fe3O4 particles, there was only weak adsorption. The acidity or basicity of the OH groups on the particle surface was the key factor that determined if a surface reaction occurred. When the OH groups were acidic, the titanate coupling reagent reacted with these, but otherwise, there was no reaction. The surface density of OH groups on the original particles and the amount of titanate coupling reagent adsorbed and reacted were estimated from TG analysis. The reactivity of the surface OH groups of Al2O3 particles was higher than that of the SiO2 particles.     

MCM-41分子筛负载钼钴系催化剂的程序升温硫化研究

采用程序升温硫化（TPS）技术，研究了负载于MCM－41分子筛的钼钴系催化剂的性能，根据TPOS结果可知，（1）载体和MoO3相互作用的强度顺序如下：Al2O3＞Al2O3-MCM-41＞MCM－41＞TiO2－MCM－41，说明TiO2具有削弱MCM－41和MoO3作用的能力；而Al2O3则相反，它增加了MoO3和MCM－41的相互作用。（2）助剂CoO对负载于未经改性的MCM－41载体上的MoO3的硫化没有明显的促进作用，这和以Al2O3为载体的情况下不同，在Al2O3上，MoO3和CoO可能生成Co-Mo－O复合相，从而促进了MoO3的硫化。（3）助剂CoO对负载于经TiO2和Al2O3改性的MCM－41上的MoO3的硫化起了促进作用。     

Photocatalytic polypyrrole-TiO2-nanoparticles composite thin film generated at the air-water interface

Herein, we report a new method of generation of TiO(2) nanoparticles (NPs) incorporated thin films of polypyrrole (PPy) at the air-water interface. Aqueous TiO(2) NPs when treated with H(2)O(2) and left in a chamber of pyrrole vapor resulted in the formation of a film at the interface, in addition to bulk precipitate. Spectroscopic, X-ray diffraction, and electron microscopic measurements establish the formation of a thin film of PPy with the incorporation of TiO(2) NPs. The TiO(2)-containing PPy films when transferred onto glass substrates were able to photo catalyze the decomposition of aqueous organic dyes: methyl orange and methylene blue. Further, these films could also photo catalyze the oxidation of iodide to triiodide ions in aqueous potassium iodide solution. We find that the PPy-TiO(2) composite films catalyze the reactions in the presence of light more efficiently than a suspension of TiO(2) NPs.     

基于铝离子掺杂二氧化钛薄膜的染料敏化太阳能电池的光电性能

采用水热法制备出Al3+掺杂二氧化钛薄膜,通过玻璃棒涂于导电玻璃上,在450°C的温度下烧结并将其用N3染料敏化制成染料敏化太阳能电池(DSSCs).通过X射线光电子能谱(XPS)、X射线衍射(XRD)、扫描电镜(SEM)及DSSCs测试系统对其进行了测试表征,研究了Al3+掺杂对TiO2晶型及染料敏化太阳能电池的光电性能影响.XPS数据显示Al3+成功掺杂到了TiO2晶格内,由于Al3+的存在,对半导体内电子和空穴的捕获及阻止电子/空穴对的复合发挥重要作用.莫特-肖特基曲线显示掺杂Al3+后二氧化钛平带电位发生正移,并导致电子从染料注入到TiO2的驱动力提高.DSSCs系统测试结果表明,Al3+掺杂的TiO2薄膜光电效率达到6.48%,相对于无掺杂的纯二氧化钛薄膜光电效率(5.58%),其光电效率提高了16.1%,短路光电流密度从16.5mA·cm-2提高到18.2mA·cm-2.     

负载型TiO2-Al2O3复合载体在超深度加氢脱硫中的应用

运用HRTEM、FT-Raman、TPR等方法表征了Mo活性组分在负载型TiO2-Al2O3复合载体和Al2O3上不同形态和性质。比较了TiO2-Al2O3复合载体同传统Al2O3载体对CoMo催化剂结构的影响,并以4,6-二甲基二苯并噻吩（4,6-DMDBT）为探针考察了催化剂的超深度加氢脱硫（UHDS）性能。结果表明,在负载型TiO2-Al2O3复合载体中, MoO3同载体之间的相互作用较弱,这种弱的相互作用使MoO3更多的以八面体配位Mo物种（MoⅥ）及其二维的聚合物的形式存在。二维聚合物有利于形成具有更高活性的多层MoS2结构,明显提高催化剂的超深度加氢脱硫催化活性。     

铝材表面状态对TiO2薄膜光催化性能和光致亲水性的影响

在纯铝片和具有氧化铝层的铝片上用提拉法制备TiO2/Al和TiO2/Al2O3/Al样片,通过FTIRATR技术和密闭间歇式反应装置分别考察了TiO2薄膜对油酸和乙烯的光催化降解性能,通过测试接触角考察TiO2薄膜的光致亲水性.结果表明,TiO2/Al2O3/Al对油酸的光降解性能比TiO2/Al的好,但其光催化氧化乙烯性能和光致亲水性能较差.这种差别可通过不同过程的作用机理和Al与TiO2表面的电子转移作用得到较好解释,由此得出TiO2薄膜的光催化性能与光致亲水性可能是两种既有联系又相互独立的性质     

TiO2 *nH2 O凝胶预处理对水热合成SrTiO3 粉的影响

以TiCl4为钛源, 首先制备TiO2 * nH2O凝胶, 然后在80℃的水热条件下制备了SrTiO3粉.利用X射线衍射(XRD)、透射电子显微镜(TEM)和红外光谱(FTIR)研究了TiO2 * nH2O凝胶水洗方式、阴离子(Cl-和NO3-)以及TiO2 * nH2O热处理对SrTiO3粉性能的影响.结果表明, 水洗和热处理都能使TiO2 * nH2O凝胶产生晶化; TiO2 * nH2O的晶化程度对产物SrTiO3颗粒的粒度和粒度分布有很大影响,以非晶质TiO2 * nH2O为钛源制备的SrTiO3颗粒粒度大且粒度分布宽.以结晶TiO2 * nH2O为钛源制备的SrTiO3颗粒粒度小且粒度分布窄,而且可以得到纳米颗粒.水热反应液相中存在Cl-或NO3-能使产物SrTiO3颗粒粒度稍有增大.综合以上结果, TiO2 * nH2O凝胶水洗对产物颗粒的影响主要是由于使凝胶产生了晶化,而由阴离子脱除产生的影响很小.因此,在不考虑阴离子对其它工程化影响(如设备腐蚀等)的前提下,可采用热处理代替水洗.