InGaN蓝光与CdTe纳米晶基白光LED

报道了倒装焊InGaN蓝光LED与黄光CdTe纳米晶的复合结构。利用蓝光作为CdTe纳米晶的激发源,通过光的下转换机制,将部分蓝光转化为黄光,复合发射出白光。室温下正向驱动电流为10mA时,发光色品坐标为x=0.29,y=0.30。实验表明,该复合结构白光LED的一大优点在于,复合光的色品坐标几乎不随正向驱动电流大小变化,颜色稳定。     

Optimization towards reduction of efficiency droop in blue GaN/InGaN based light emitting diodes

Light emitting diodes (LEDs) based on GaN/InGaN material suffer from efficiency droop at high current injection levels. We propose multiple quantum well (MQW) GaN/InGaN LEDs by optimizing the barrier thickness and high–low–high indium composition to reduce the efficiency droop. The simulation results reflect a significant improvement in the efficiency droop by using barrier width of 10 nm and high–low–high indium composition in MQW LED.     

表面InGaN厚度对GaN基发光二极管特性的影响

通过调整GaN基发光二极管(LED)表面InGaN层的厚度,发现在20 mA电流驱动下,LED器件的正向压降有明显差距.本文考虑了极化效应的影响,通过求解InGaN/GaN三角形势阱内二维空穴气浓度以及空穴隧穿概率的变化,求得了表面InGaN层厚度不同时器件正向压降的变化趋势,发现理论结果与实验结果有很好的吻合.同时得到了获得最低正向压降的表面InGaN厚度. 关键词： 极化 二维空穴气 隧穿概率     

表面InGaN厚度对GaN基发光二极管特性的影响

通过调整GaN基发光二极管(LED)表面InGaN层的厚度，发现在20 mA电流驱动下，LED器件的正向压降有明显差距.本文考虑了极化效应的影响，通过求解InGaN/GaN三角形势阱内二维空穴气浓度以及空穴隧穿概率的变化，求得了表面InGaN层厚度不同时器件正向压降的变化趋势，发现理论结果与实验结果有很好的吻合.同时得到了获得最低正向压降的表面InGaN厚度.     

InGaN/GaN多量子阱结构发光二极管发光机理转变的低频电流噪声表征

本文对InGaN/GaN多量子阱结构发光二极管开启后的电流噪声进行了测试, 结合低频电流噪声的特点和载流子之间的复合机理, 研究了低频电流噪声功率谱密度与发光二极管发光转变机理之间的关系. 结论表明, 当电流从0.1 mA到10 mA逐渐增大的过程中, InGaN/GaN发光二极管的电流噪声行为从产生-复合噪声逐渐接近于低频1/f噪声, 载流子的复合机理从非辐射复合过渡为电子与空穴之间载流子数的辐射复合, 并具有标准1/f噪声的趋势, 此时多量子阱中的电子和空穴之间的复合趋向于稳定. 本文的结论提供了一种表征InGaN/GaN多量子阱发光二极管发光机理转变的有效方法, 为进一步研究发光二极管中载流子的复合机理、优化和设计发光二极管、提高其发光量子效率提供理论依据.     

Electrical Characteristics of InGaN/AlGaN and InGaN/GaN MQW Near UV-LEDs

Electrical characteristics of In0.05 Ga0.95N/Al0.07Ga0.9aN and In0.05 Ga0.95N/GaN multiple quantum well （MQW） ultraviolet light-emltting diodes （UV-LEDs） at 400hm wavelength are measured. It is found that for InGaN/AlGaN MQW LEDs, both ideality factor and parallel resistance are similar to those of InGaN/GaN MQW LEDs, while series resistance is two times larger. It is suggested that the Al0.07Ga0.93N barrier layer did not change crystal quality and electrical characteristic of p-n junction either, but brought larger series resistance. As a result, InGaN/AlGaN MQW LEDs suffer more serious thermal dissipation problem although they show higher light output efficiency.     

Enhanced performance of GaN-based light-emitting diodes with InGaN/GaN superlattice barriers

GaN-based multiple quantum well light-emitting diodes （LEDs） with conventional and superlattice barriers have been investigated numerically. Simulation results demonstrate using InGaN/GaN superlattices as barriers can effectively enhance performances of the GaN-Based LEDs, mainly owing to the improvement of hole injection and transport among the MQW active region. Meanwhile, the improved electron capture decreases the electron leakage and alleviates the efficiency droop. The weak polarization field induced by the superlattice structure strengthens the intensity of the emission spectrum and leads to a blue-shift relative to the conventional one.     

高效InGaN/AlInGaN发光二极管的结构设计及其理论研究

利用Advanced Physical Models of Semiconductor Devices (APSYS)理论对比研究了InGaN/AlInGaN 和 InGaN/GaN多量子阱作为有源层的InGaN基发光二极管的结构和电学特性。与InGaN/GaN 基LED 中GaN作为垒层材料相比,在AlInGaN材料体系中,通过调节AlInGaN中Al和In的组分可以优化器件的性能。当InGaN阱层材料中In组分为8%时,可以实现无应力的In_0.08Ga_0.92N/AlInGaN基 LED。在这种无应力结构中可以进一步降低大功率LED的"效率下降"(Effciency droop)问题。理论模拟结果显示,四元系AlInGaN作为垒层可以进一步减少载流子泄露,增加空穴注入效率,减少极化场对器件性能的影响。在In_0.08Ga_0.92N /AlInGaN量子阱中的载流子浓度、有源层的辐射复合率、电流特性曲线和内量子效率等方面都优于InGaN/GaN基LED。无应变AlInGaN垒层代替传统的GaN垒层后,能够得到高效的发光二极管,并且大电流注入下的"效率滚降"问题得到改善。     

Droop improvement in blue InGaN light-emitting diodes with GaN/InGaN superlattice barriers

GaN/InGaN superlattice barriers are used in InGaN-based light-emitting diodes （LEDs）. The electrostatic field in the quantum wells, electron hole wavefunction overlap, carrier concentration, spontaneous emission spectrum, light-current performance curve, and internal quantum efficiency are numerically investigated using the APSYS simulation software. It is found that the structure with GaN/InGaN superlattice barriers shows improved light output power, and lower current leakage and efficiency droop. According to our numerical simulation and analysis, these improvements in the electrical and optical characteristics are mainly attributed to the alleviation of the electrostatic field in the active region.     

Simulation of InGaN/GaN light-emitting diodes with a non-local quantum well transport model

Blue InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) are simulated by the APSYS software with a non-local quantum well transport model which is used to describe the phenomenon that carriers can fly over the quantum wells directly. The simulation results based on this model are in good agreement with the experiment and show its significant influence on the output power, carrier transport, peak wavelength and current crowding effect of the InGaN/GaN MQW LEDs, indicating that the non-local quantum well transport plays an important role in these devices.     

MOCVD生长InGaN/GaN MQW紫光LED

利用LP－MOCVD系统生长了InGaN/GaN MQW紫光LED外延片，双晶X射线衍射测试获得了2级卫星峰，室温光致发光谱的峰值波长为399.5nm，FWHM为15.5nm，波长均匀性良好。制成的LED管芯，正向电流20mA时，工作电压在4V以下。     

Characteristics of InGaN light emitting diode depending on Si-doping on InGaN layers below quantum wells

Effect of Si-doping on InGaN layers below the quantum wells (QWs), which cause different levels of charge concentration in the depletion region, have been investigated for InGaN light emitting diodes (LEDs). Four groups of InGaN LEDs with different levels of Si-doping on InGaN/GaN layers below quantum-wells have been produced for the experiment (i.e., 0.5 × 10¹⁷ cm^?3 for group A, 1 × 10¹⁷ cm^?3 for group B, 5 × 10¹⁷ cm^?3 for group C, and 1 × 10¹⁸ cm^?3 for group D.) The reverse leakage current of LED can be significantly decreased and the light output power of LED can be enhanced by lowering the background charge concentration in the depletion region of LED. Such result enables us to improve the device lifetime by inhibiting the degradation of the GaN-based LED.     

具有超晶格应力调制结构的绿光InGaN/GaN多量子阱的发光特性

研究了具有InGaN/GaN超晶格(SL)插入结构的绿光InGaN/GaN多量子阱(MQW)的发光特性。结构测试表明,SL插入结构并没有引起MQW中平均In组份的增加,而是改变了In组份的分布,形成了高In组份的量子点和低In组份量子阱。其电致发光(EL)谱和光致发光(PL)谱均出现了双发光峰。我们认为这两个 峰分别来自于量子点和量子阱,且存在着载流子从阱向点转移的输运机制。最后变温PL积分强度的Arrhenius 拟合表明,SL插入结构并没有在MQW中引入新的缺陷,使其发光效率下降。     

High power and high reliability GaN/InGaN flip-chip light-emitting diodes

High-power and high-reliability GaN/InGaN flip-chip light-emitting diodes (FCLEDs) have been demonstrated by employing a flip-chip design, and its fabrication process is developed. FCLED is composed of a LED die and a submount which is integrated with circuits to protect the LED from electrostatic discharge (ESD) damage. The LED die is flip-chip soldered to the submount, and light is extracted through the transparent sapphire substrate instead of an absorbing Ni/Au contact layer as in conventional GaN/InGaN LED epitaxial designs. The optical and electrical characteristics of the FCLED are presented. According to ESD IEC61000-4-2 standard (human body model), the FCLEDs tolerated at least 10\,kV ESD shock have ten times more capacity than conventional GaN/InGaN LEDs. It is shown that the light output from the FCLEDs at forward current 350mA with a forward voltage of 3.3\,V is 144.68\,mW, and 236.59\,mW at 1.0\,A of forward current. With employing an optimized contact scheme the FCLEDs can easily operate up to 1.0\,A without significant power degradation or failure. The life test of FCLEDs is performed at forward current of 200\,mA at room temperature. The degradation of the light output power is no more than 9\% after 1010.75\,h of life test, indicating the excellent reliability. FCLEDs can be used in practice where high power and high reliability are necessary, and allow designs with a reduced number of LEDs.     

具有三角形InGaN/GaN多量子阱的高内量子效率的蓝光LED(英文)

对InGaN量子阱LED的内量子效率进行了优化研究。分别对发光光谱、量子阱中的载流子浓度、能带分布、静电场和内量子效应进行了理论分析。对具有不同量子阱数量的InGaN/GaN LED进行了理论数值比对研究。研究结果表明,对于传统结构的LED而言,2个量子阱的结构相对于5个和7个量子阱具有更好的光学性能。同时还研究了具有三角形量子阱结构的LED,研究结果显示,三角形多量子阱结构具有较高的电致发光强度、更高的内量子效率和更好的发光效率,所有的优点都归因于较高的电子-空穴波函数重叠率和低的Stark效应所产生的较高的载流子输入效率和复合发光效率。     

InGaN/GaN多量子阱蓝光发光二极管老化过程中的光谱特性

系统地研究了小注入电流(＜4 mA)下InGaN/GaN多量子阱结构蓝光发光二极管的发光光谱特性在老化过程中的变化。对比老化前后的电致发光(EL)光谱,发现在注入电流1 mA下的峰值波长(peak wavelength)和半高宽(FWHM)随老化时间增加而减小,变化过程分两个阶段：前期(＜100 h)减小速度较快,而后逐渐变缓,呈现出与LEDs的发光光功率一致的变化规律,说明LEDs的等效极化电场在老化过程中减弱,这一变化和量子阱内缺陷的增加有明确的关系。通过电学特性测量发现同一结电压(V_j=1.8 V)下的结电容C_j和由交流小信号I—V方法计算得到的注入电流1 mA下的结电压V_j随老化时间增加而增大,明确了在同等小注入电流下量子阱内的载流子浓度随老化过程增加。分析表明在老化过程中InGaN/GaN 多量子阱结构蓝光发光二极管量子阱内的缺陷及其束缚的载流子数量增加,形成了增强的极化电场屏蔽效应,减弱的等效极化电场导致了量子阱的能带倾斜变小,带边辐射复合能量增大,能态密度增多,对应的发光过程的峰值波长变短(蓝移),半高宽变窄。     

Investigation of blue InGaN light-emitting diodes with p-AlGaN/InGaN superlattice interlayer

The blue InGaN light-emitting diodes (LEDs), employing a lattice-compensated p-AlGaN/InGaN superlattice (SL) interlayer to link the last quantum barrier and electron blocking layer (EBL), are proposed and investigated numerically. The simulation results indicate that the newly designed LEDs have better hole injection efficiency, lower electron leakage, and smaller electrostatic fields in the active region over the conventional LEDs mainly attributed to the mitigated polarization-induced downward band bending. Furthermore, the markedly improved output power and efficiency droop are also suggested when the conventional LEDs corresponding to experiment data are replaced by the newly designed LEDs.     

Performance Improvement of GaN-Based Violet Laser Diodes

The influences of InGaN/GaN multiple quantum wells(MQWs) and AlGaN electron-blocking layers(EBL) on the performance of GaN-based violet laser diodes are investigated. Compared with the InGaN/GaN MQWs grown at two different temperatures, the same-temperature growth of InGaN well and GaN barrier layers has a positive effect on the threshold current and slope efficiency of laser diodes, indicating that the quality of MQWs is improved. In addition, the performance of GaN laser diodes could be further improved by increasing Al content in the AlGaN EBL due to the fact that the electron leakage current could be reduced by properly increasing the barrier height of AlGaN EBL. The violet laser diode with a peak output power of 20 W is obtained.     

High-performance InGaN/GaN MQW LEDs with Al-doped ZnO transparent conductive layers grown by MOCVD using H_2O as an oxidizer

In this study,the high performance of InGaN/GaN multiple quantum well light-emitting diodes(LEDs) with Aldoped ZnO(AZO) transparent conductive layers(TCLs) has been demonstrated.The AZO-TCLs were fabricated on the n~+-InGaN contact layer by metal organic chemical vapor deposition(MOCVD) using H_2O as an oxidizer at temperatures as low as 400 ℃ without any post-deposition annealing.It shows a high transparency(98%),low resistivity(510 ~4 Ω·cm),and an epitaxial-like excellent interface on p-GaN with an n+-InGaN contact layer.A forward voltage of 2.82 V @ 20 mA was obtained.Most importantly,the power efficiencies can be markedly improved by 53.8%@20 mA current injection and 39.6%@350 mA current injection compared with conventional LEDs with indium tin oxide TCL(LED-Ⅲ),and by28.8%@20 mA current injection and 4.92%@350 mA current injection compared with LEDs with AZO-TCL prepared by MOCVD using O_2 as an oxidizer(LED-Ⅱ),respectively.The results indicate that the AZO-TCL grown by MOCVD using H_2O as an oxidizer is a promising TCL for a low-cost and high-efficiency GaN-based LED application.     

Status of GaN-based green light-emitting diodes

GaN-based blue light emitting diodes(LEDs) have undergone great development in recent years,but the improvement of green LEDs is still in progress.Currently,the external quantum efficiency(EQE) of GaN-based green LEDs is typically30%,which is much lower than that of top-level blue LEDs.The current challenge with regard to GaN-based green LEDs is to grow a high quality In GaN quantum well(QW) with low strain.Many techniques of improving efficiency are discussed,such as inserting Al GaN between the QW and the barrier,employing prestrained layers beneath the QW and growing semipolar QW.The recent progress of GaN-based green LEDs on Si substrate is also reported:high efficiency,high power green LEDs on Si substrate with 45.2% IQE at 35 A/cm2,and the relevant techniques are detailed.