On-line ionic imprinted polymer selective solid-phase extraction of nickel and lead from seawater and their determination by inductively coupled plasma-optical emission spectrometry

Nickel(II) and lead(II) ionic imprinted 8-hydroxyquinoline polymers were synthesized by a precipitation polymerization technique and were used as selective solid phase extraction supports for the determination of nickel and lead in seawater by flow injection solid phase extraction on-line inductively coupled plasma-optical emission spectrometry. An optimum loading flow rate of 2.25 mL min⁻¹ for 2 min and an elution flow rate of 2.25 mL min⁻¹ for 1 min gave an enrichment factor of 15 for nickel. However, a low dynamic capacity and/or rate for adsorption and desorption was found for lead ionic imprinted polymer and a flow rate of 3.00 mL min⁻¹ for 4-min loading and a flow rate of 2.25 mL min⁻¹ for 1-min elution gave a enrichment factor of 5. The limit of detection was 0.33 μg L⁻¹ for nickel and 1.88 μg L⁻¹ for lead, with a precision (n = 11) of 8% (2.37 μg Ni L⁻¹) for nickel and 11% (8.38 μg Pb L⁻¹) for lead. Accuracy was also assessed by analyzing SLEW-3 (estuarine water) and TM-24 (lake water) certified reference materials, and the values determined were in good agreement with the certified concentrations.     

Determination of additives in an electrolytic zinc bath by q1H-NMR spectroscopy

The use of proton nuclear magnetic resonance (¹H-NMR) for the quantification of additives in an electrolytic Zn bath is reported. A simple and quick method is described that does not need any prior sample preparation. Contrary to other analytical methods, the three additives in the bath, benzylidene acetone (BDA), benzoic acid (BA) and poly(ethylene glycol) (PE400), can be quantified. Two calibration methods were tried: integration of NMR signals with the use of an internal standard and partial least squares (PLS) regression applied to the characteristic NMR peaks. Both methods are compared and the univariate method was preferred because of simplicity, accuracy and precision. The following limits of detection were found: 0.30 g L⁻¹ BA, 0.08 g L⁻¹ BDA and 0.7 g L⁻¹ PE400 with dynamic ranges of at least 1.0–6.0, 0.1–0.6 and 3.0–18.0 g L⁻¹ respectively. Those concentration ranges are suitable to follow the concentration of additives in the bath in real time. ¹H-NMR spectra provide evidence for the BDA degradation pattern.     

Interpretation of analysis of variance models using principal component analysis to assess the effect of a maternal anticancer treatment on the mineralization of rat bones

The aim of this paper is to show how it is possible to extract analytical information from images acquired with a flatbed scanner and make use of this information for real time control of a nickel plating process. Digital images of plated steel sheets in a nickel bath are used to follow the process under degradation of specific additives. Dedicated software has been developed for making the obtained results accessible to process operators. This includes obtaining the RGB image, to select the red channel data exclusively, to calculate the histogram of the red channel data and to calculate the mean colour value (MCV) and the standard deviation of the red channel data. MCV is then used by the software to determine the concentration of the additives Supreme Plus Brightner (SPB) and SA-1 (for confidentiality reasons, the chemical contents cannot be further detailed) present in the bath (these two additives degrade and their concentration changes during the process). Finally, the software informs the operator when the bath is generating unsuitable quality plating and suggests the amount of SPB and SA-1 to be added in order to recover the original plating quality.     

Zinc electrodeposition on copper substrate using cyanide bath for the production of 66,67,68Ga

The electroplating of zinc is carried out in an alkaline cyanide bath. Operating parameters such as pH, temperature, and current density and amount of the electrolyte components are optimized. The optimum conditions of the electrodeposition of zinc were as follows: 2.7 g L⁻¹ ZnO, 7.1 g L⁻¹ KCN, 11.1 g L⁻¹ KOH, pH = 13–14, DC current density of ca 8.55 mA cm⁻² at 40–50 °C temperature with 89% current efficiency. SEM photomicrographs revealed fine-grained structure of the deposit from the bath.     

Effect of organic load on the performance and methane production of an AnSBBR treating effluent from biodiesel production

Currently, there is an increasing demand for the production of biodiesel and, consequently, there will be an increasing need to treat wastewaters resulting from the production process of this biofuel. The main objective of this work was, therefore, to investigate the effect of applied volumetric organic load (AVOL) on the efficiency, stability, and methane production of an anaerobic sequencing batch biofilm reactor applied to the treatment of effluent from biodiesel production. As inert support, polyurethane foam cubes were used in the reactor and mixing was accomplished by recirculating the liquid phase. Increase in AVOL resulted in a drop in organic matter removal efficiency and increase in total volatile acids in the effluent. AVOLs of 1.5, 3.0, 4.5 and 6.0 g COD L⁻¹ day⁻¹ resulted in removal efficiencies of 92%, 81%, 67%, and 50%, for effluent filtered samples, and 91%, 80%, 63%, and 47%, for non-filtered samples, respectively, whereas total volatile acids concentrations in the effluent amounted to 42, 145, 386 and 729 mg HAc L⁻¹, respectively. Moreover, on increasing AVOL from 1.5 to 4.5 g COD L⁻¹ day⁻¹ methane production increased from 29.5 to 55.5 N mL CH₄ g COD⁻¹. However, this production dropped to 36.0 N mL CH₄ g COD⁻¹ when AVOL was increased to 6.0 g COD L⁻¹ day⁻¹, likely due to the higher concentration of volatile acids in the reactor. Despite the higher concentration of volatile acids at the highest AVOL, alkalinity supplementation to the influent, in the form of sodium bicarbonate, at a ratio of 0.5–1.3 g NaHCO₃ g COD_fed⁻¹, was sufficient to maintain the pH near neutral and guarantee process stability during reactor operation.     

Organosilica composite for preconcentration of phenolic compounds from aqueous solutions

A new adsorbent is proposed for the solid-phase extraction of phenol and 1-naphthol from polluted water. The adsorbent (TX-SiO₂) is an organosilica composite made from a bifunctional immobilized layer comprising a major fraction (91%) of hydrophilic diol groups and minor fraction (9%) of the amphiphilic long-chain nonionic surfactant Triton X-100 (polyoxyethylated isooctylphenol) (TX). Under static conditions phenol was quantitatively extracted onto TX-SiO₂ in the form of a 4-nitrophenylazophenolate ion associate with cetyltrimethylammonium bromide. The capacity of TX-SiO₂ for phenol is 2.4 mg g⁻¹ with distribution coefficients up to 3.4 × 10⁴ mL g⁻¹; corresponding data for 1-naphthol are 1.5 mg g⁻¹ and 3 × 10³ mL g⁻¹. The distribution coefficient does not change significantly for solution volumes of 0.025–0.5 L and adsorbent mass less than 0.03 g; 1–90 μg analyte can be easily eluted by 1–3 mL acetonitrile with an overall recovery of 98.2% and 78.3% for phenol and 1-naphthol, respectively. Linear correlation between acetonitrile solution absorbance (A ₅₄₀) and phenol concentration (C) in water was found according to the equation A ₅₄₀ = (6 ± 1) × 10⁻² + (0.9 ± 0.1)C (μmol L⁻¹) with a detection range from 1 × 10⁻⁸ mol L⁻¹ (0.9 μL g⁻¹) to 2 × 10⁻⁷ mol L⁻¹ (19 μL g⁻¹), a limit of quantification of 1 μL g⁻¹ (preconcentration factor 125), correlation coefficient of 0.936, and relative standard deviation of 2.5%. A solid-phase colorimetric method was developed for quantitative determination of 1-naphthol on adsorbent phase using scanner technology and RGB numerical analysis. The detection limit of 1-naphthol with this method is 6 μL g⁻¹ while the quantification limit is 20 μL g⁻¹. A test system was developed for naked eye monitoring of 1-naphthol impurities in water. The proposed test kit allows one to observe changes in the adsorbent color when 1-naphthol concentration in water is 0.08–3.2 mL g⁻¹.     

Multisyringe Flow Injection Analysis for Determination of 1-Naphthylamine in Water Samples

1-Naphthylamine (NPA) is one of the main degradation products of pesticides derived from naphthalene, and a well-known bladder carcinogen in men. The Griess assay is used for NPA determination because of its high sensitivity and selectivity. The azo dye 4-(sulphophenylazo)-1-naphthylamine is formed, which shows a peak maximum at 540 nm. After optimizing multisyringe flow injection analysis (MSFIA) parameters, the analytical characteristics of the method were obtained, with a working linear range of 0.5 to 14 mg L⁻¹, according to the equation A = 0.0738±0.0019 [NPA] + 0.0028 ± 0.0042, r = 0.9997. Values for RSD (%) and E_rel (%) were calculated for the concentration levels of 0.5, 6 and 12 mg L⁻¹; values obtained were 1.1, 0.4 and 0.3% for RSD and 0.8, 0.3 and 0.2% for E_rel, respectively. LD was 0.01 mg L⁻¹ and LQ was 0.04 mg L⁻¹ NPA. The MSFIA procedure for the determination of NPA was applied to different water samples (well water, tap water, seawater, and wastewater from the EDAR-1, Palma de Mallorca water treatment plant), with satisfactory results and a throughput of 90 samples per hour.     

Flow injection on-line determination of uranium after preconcentration on XAD-4 resin impregnated with dibenzoylmethane

A flow injection on-line determination of uranium(VI) after preconcentration in a minicolumn having amberlite XAD-4 resin impregnated with dibenzoylmethane (DBM) is described. Uranium(VI) is selectively adsorbed from aqueous solution of pH 5.5 in the minicolumn (5.5 cm long with 5.0 mm i.d.) at a flow rate of 13.6 mL min⁻¹. The uranium(VI) complex was desorbed from the resin by 0.1 mol dm⁻³ HCl at a flow rate of 4.2 mL min⁻¹ and mixed with arsenazo-III solution (0.05% solution in 0.1 mol dm⁻³ HCl, 4.2 mL min⁻¹), and taken to the flow through cell of spectrophotometer where its absorbance was measured at 651 nm. Various parameters affecting the complex formation and its elution were optimized. Peak height (absorbance) was used for data analyses. The preconcentration factors of 36 and 143, detection limits of 0.9 and 0.232 μg L⁻¹, sample throughputs of 40 and 10 were obtained for preconcentration time of 60 and 300 s, respectively. The tolerance limits of many interfering cations like Th(IV) and rare-earth elements were improved. The proposed method was applied on different water (spiked tap, well and sea water) and biological samples and good recovery was obtained. The method was also validated on mocked uranium ore sample and the results were in good agreement with the reported value.     

Ultra-fast HPLC-ICP-MS analysis of oxaliplatin in patient urine

A novel method for rapid HPLC-ICP-MS analysis of oxaliplatin in human urine was developed implementing a stationary HPLC phase with a particle size of 1.8 μm. The method allowed a cycle time of <1 min at a HPLC flow rate of 0.9 mL min⁻¹. Procedural limits of detection of 0.05 μg L⁻¹ oxaliplatin (150 fg on column) were obtained. Analysis of oxaliplatin in patient urine showed that accurate quantification of the intact drug demanded for storage at −80 °C and rapid measurement after thawing.     

Simultaneous speciation of arsenic (As(III), MMA, DMA, and As(V)) and selenium (Se(IV), Se(VI), and SeCN−) in petroleum refinery aqueous streams

High-performance liquid chromatography (HPLC) coupled to an ICP-MS with an octapole reaction system (ORS) has been used to carry out quantitative speciation of selenium (Se) and arsenic (As) in the stream waters of a refining process. The argon dimers interfering with the ⁷⁸Se and ⁸⁰Se isotopes were suppressed by pressurizing the octapole chamber with 3.1 mL min⁻¹ H₂ and 0.5 mL min⁻¹ He. Four arsenic species arsenite—As(III), arsenate (As(V)), monomethylarsonic acid (MMA), and dimethylarsinic acid (DMA)—and three inorganic Se species—selenite Se(IV), selenate Se(VI), and selenocyanate (SeCN⁻)—were separated in a single run by ion chromatography (IC) using gradient elution with 100 mmol L⁻¹ NH₄NO₃, pH 8.5, adjusted by addition of NH₃, as eluent. Repeatabilities of peak position and of peak area evaluation were better than 1% and about 3%, respectively. Detection limits (as 3σ of the baseline noise) were 81, 56, and 75 ng L⁻¹ for Se(IV), Se(VI), and SeCN⁻, respectively, and 22, 19, 25, and 16 ng L⁻¹ for As(III), As(V), MMA, and DMA, respectively. Calibration curve R ² values ranged between 0.996 and 0.999 for the arsenic and selenium species. Column recovery for ion chromatography was calculated to be 97 ± 6% for combined arsenic species and 98 ± 3% for combined selenium species. Because certified reference materials for As and Se speciation studies are still not commercially available, in order to check accuracy and precision the method was applied to certified reference materials, BCR 714, BCR 1714, and BCR 715 and to two different refinery samples—inlet and outlet wastewater. The method was successfully used to study the quantitative speciation of selenium and arsenic in petroleum refinery wastewaters.     

Application of inorganic sorbents for removal of Cs, Sr, Pu and Am from contaminated solutions

A sorption ability of titanium silicates (TiSi) and iron oxides towards Cs, Sr, Pu and Am was tested using the laboratory batch method. The obtained results are expressed as distribution coefficients (K_d). TiSi synthesised using TiOSO₄ revealed better sorption ability towards all studied radionuclides in comparison with TiSi produced on the basis of TiCl₄. The K_d values ranged from 3.9 × 10² to 1.6 × 10⁵ mL g⁻¹ for Sr, from 6 to 4.1 × 10⁴ mL g⁻¹ for Cs, from 2.2 × 10² to 2.6 × 10⁵ mL g⁻¹ for Pu and from 50 to 1.6 × 10⁴ mL g⁻¹ for Am. The highest Pu K_d values (9 × 10³–6.2 × 10⁴ mL g⁻¹) and better kinetics were found for iron oxides.     

Adsorption properties of BEA zeolites and their aluminum phosphate extrudates for purification of isomaltose

The disaccharide isomaltose is produced via an enzymatic reaction and is adsorbed to BEA zeolite. This reaction integrated adsorption can be achieved as fluidized bed as well as fixed bed. We investigated isotherms, adsorption enthalpies and sorption kinetics of BEA zeolite and extrudates with a novel aluminum phosphate sintermatrix. These extrudates contain 50% (w/w) of BEA 150 zeolites (Si/Al = 75) as primary crystals. BET-surface for extrudates is 245 m²⋅g⁻¹ and 487 m²⋅g⁻¹ for zeolite. Extrudates show a monomodal macropore structure with a maximum at 90 nm. All isotherms show a type I shape. For lower equilibrium concentrations, which occur during the enzymatic reaction, Henry’s law is applied and compared to a Langmuir model. Adsorption equilibrium constant K _i,L calculated from Langmuir for extrudates at 4 °C is 64.7 mL⋅g⁻¹ and more than twice as high as obtained from Henry’s law with K _i is 26.8 mL⋅g⁻¹. Adsorption on extrudates at 4 °C is much stronger than on zeolite crystals where the Henry coefficient K _i is 17.1 mL⋅g⁻¹. Adsorption enthalpy Δh _Ad calculated from van’t Hoff plot with the Henry equation is −44.3 kJ⋅mol⁻¹ for extrudates and −29.6 kJ⋅mol⁻¹ for zeolite crystals. Finally, the kinetics for ad- and desorption were calculated from the initial slope. The diffusion rate for ad- and desorption on extrudates were in the same range while adsorption on zeolites is three orders of magnitudes faster than desorption.     

Multi-wall carbon nanotube aqueous dispersion monitoring by using A4F-UV-MALS

In this work, the potentiality of asymmetrical flow field-flow fractionation (A4F) hyphenated to UV detector and multi-angle light scattering (MALS) was investigated for accurately determining multi-walled carbon nanotube (MWCNT) length and its corresponding dispersion state in aqueous medium. Fractionation key parameters were studied to obtain a method robust enough for heterogeneous sample characterization. The main A4F conditions were 10⁻⁵ mL min⁻¹ NH₄NO₃, elution flow of 1 mL min⁻¹, and cross flow of 2 mL min⁻¹. The recovery was found to be (94 ± 2)%. Online MALS analysis of eluted MWCNT suspension was performed to obtain length distribution. The length measurements were performed with a 4% relative standard deviation, and the length values were shown to be in accordance with expected ones. The capabilities of A4F-UV-MALS to size characterize various MWCNT samples and differentiate them according to their manufacturing process were evaluated by monitoring ball-milled MWCNT and MWCNT dispersions. The corresponding length distributions were found to be over 150–650 and 150–1,156 nm, respectively. A4F-UV-MALS was also used to evaluate MWCNT dispersion state in aqueous medium according to the surfactant concentration and sonication energy involved in the preparation of the dispersions. More especially, the presence or absence of aggregates, number and size of different populations, as well as size distributions were determined. A sodium dodecyl sulfate concentration of 15 to 30 mmol L⁻¹ and a sonication energy ranged over 20–30 kJ allow obtaining an optimal MWCNT dispersion. It is especially valuable for studying nanomaterials and checking their manufacturing processes, size characterization being always of high importance.     

Catanionic surfactant ambient cloud point extraction and high-performance liquid chromatography for simultaneous analysis of organophosphorus pesticide residues in water and fruit juice samples

A mixed anionic–cationic surfactant cloud point extraction (CPE) has been developed using sodium dodecyl sulfate (SDS) and tetrabutylammonium bromide (TBABr) for the extraction and preconcentration of organophosphorus pesticides (OPPs) at ambient temperature before analysis by high-performance liquid chromatography. The studied OPPs were azinphos-methyl, parathion-methyl, fenitrothion, diazinon, chlorpyrifos, and prothiophos. The optimum conditions of the mixed anionic–cationic CPE were 50 mmol L⁻¹ SDS, 100 mmol L⁻¹ TBABr, and 10% (w/v) NaCl. The extracted OPPs were successfully separated within 11 min using the conditions of a Waters Symmetry C8 column, a flow rate of 0.8 mL min⁻¹, a gradient elution of methanol and water, and detection at 210 nm. Linearity was found over the range 0.05–5 μg mL⁻¹, with the correlation coefficients higher than 0.996. The enrichment factor of the target analytes was in the range 6–11, which corresponds to their limits of detection from 1 to 30 ng mL⁻¹. High precisions (intra-day and inter-day) were obtained with relative standard deviation <1.5% (t _R) and 10% (peak area). Accuracies (% recovery) of the different spiked OPP concentrations were 82.7–109.1% (water samples) and 80.3–113.3% (fruit juice samples). No contamination by the OPPs was observed in any studied samples.     

Application of molecularly imprinted polymer solid-phase extraction for salivary cotinine

A method constituted by molecularly imprinted solid-phase extraction (MISPE) with high-performance liquid chromatography coupled to diode array detector (HPLC-DAD) was developed for cotinine analysis in saliva samples. For this purpose, the separation was carried out with a C18 reversed-phase column at 20 °C. The mobile phase which was composed of a mixture of 09:91 (v/v) acetonitrile/phosphate buffer, pH 6.3, was delivered with isocratic flow rate at 1.4 mL min⁻¹. Employing MISPE, the best conditions were achieved with 1.5 mL of saliva plus 1.5 mL of 0.1 mol L⁻¹ of acetate buffer, pH 5.5, which were then passed through a cartridge previously conditioned with 2 mL acetonitrile, 2 mL methanol, and 2 mL of 0.1 mol L⁻¹ sodium acetate buffer, pH 5.5. The washing was carried out with 1 mL deionized water, 1 mL of 0.1 mol L⁻¹ sodium hydroxide, and 1 mL hexane; finally; the cotinine elution was carried out with 3 mL methanol/water (97.5: 2.5, v/v). Linearity ranged from 30 to 500 ng mL⁻¹ with r > 0.99. Intra-assay, interassay precision, and accuracy ranged from 3.1% to 10.1%, 5.2% to 15.9%, and 99.22% to 111.17%, respectively. The detection and quantification limits were 10 and 30 ng mL⁻¹, respectively. This investigation has provided a reliable method for routine cotinine determination in saliva, and it is an important tool for monitoring cigarette smoke exposure in smokers. The method was applied in five smokers’ samples who consumed around five to 20 cigarettes per day and the values of cotinine in saliva were from 66.7 to 316.16 ng mL⁻¹.     

Fermentation Performance and Structure Characteristics of Xanthan Produced by <Emphasis Type="Italic">Xanthomonas campestris</Emphasis> with a Glucose/Xylose Mixture

The ability of Xanthomonas campestris to convert glucose and xylose to xanthan and the structure of xanthan derived from the glucose/xylose mixture media are important when the lignocelluloses hydrolysate was used in xanthan production. In this paper, the features related to xanthan fermentation in the glucose/xylose mixture media and the structures of xanthan derived from the mixture media were studied. Glucose was the preferred carbon source to produce xanthan while xylose was also utilized with a very low consumption rate. When the fraction of glucose decreased from 100% to 25%, the glucose consumption rate and xanthan production rate reduced from 0.44 g L⁻¹ h⁻¹ to 0.25 g L⁻¹ h⁻¹ and 0.21 g L⁻¹ h⁻¹ to 0.04 g L⁻¹ h⁻¹ respectively while xylose was consumed at a very stable rate (0.053–0.060 g L⁻¹ h⁻¹). On the other hand, when the xylose fraction increased from 0% to 50%, pyruvate and acetate content of xanthan increased from 2.43% to 3.78% and 2.55% to 7.05%. The existence of xylose also led to higher average molecular weight. Therefore, it could be concluded that xylose was not efficiently utilized by X. campestris to produce xanthan. The concentration of glucose rather than the total sugar was the main factor to determine the xanthan production. But xylose was helpful to improve the quality of xanthan.     

LC–MS–MS determination of ibuprofen, 2-hydroxyibuprofen enantiomers,and carboxyibuprofen stereoisomers for application in biotransformation studies employing endophytic fungi

The purpose of this study was the development and validation of an LC–MS–MS method for simultaneous analysis of ibuprofen (IBP), 2-hydroxyibuprofen (2-OH-IBP) enantiomers, and carboxyibuprofen (COOH-IBP) stereoisomers in fungi culture medium, to investigate the ability of some endophytic fungi to biotransform the chiral drug IBP into its metabolites. Resolution of IBP and the stereoisomers of its main metabolites was achieved by use of a Chiralpak AS-H column (150 × 4.6 mm, 5 μm particle size), column temperature 8 °C, and the mobile phase hexane–isopropanol–trifluoroacetic acid (95: 5: 0.1, v/v) at a flow rate of 1.2 mL min⁻¹. Post-column infusion with 10 mmol L⁻¹ ammonium acetate in methanol at a flow rate of 0.3 mL min⁻¹ was performed to enhance MS detection (positive electrospray ionization). Liquid–liquid extraction was used for sample preparation with hexane–ethyl acetate (1:1, v/v) as extraction solvent. Linearity was obtained in the range 0.1–20 μg mL⁻¹ for IBP, 0.05–7.5 μg mL⁻¹ for each 2-OH-IBP enantiomer, and 0.025–5.0 μg mL⁻¹ for each COOH-IBP stereoisomer (r ≥ 0.99). The coefficients of variation and relative errors obtained in precision and accuracy studies (within-day and between-day) were below 15%. The stability studies showed that the samples were stable (p > 0.05) during freeze and thaw cycles, short-term exposure to room temperature, storage at −20 °C, and biotransformation conditions. Among the six fungi studied, only the strains Nigrospora sphaerica (SS67) and Chaetomium globosum (VR10) biotransformed IBP enantioselectively, with greater formation of the metabolite (+)-(S)-2-OH-IBP. Formation of the COOH-IBP stereoisomers, which involves hydroxylation at C3 and further oxidation to form the carboxyl group, was not observed.     

Binary biosorption of uranium(VI) and nickel(II) from aqueous solution by Ca-pretreated Cystoseira indica in a fixed-bed column

Simultaneous biosorption of uranium(VI) and nickel(II) ions onto Ca-pretreated Cystoseira indica biomass was studied and compared with single uranium or nickel biosorption in a fixed-bed column. Results of single biosorption showed the breakthrough and exhaustion time increase with the increase of the flow rate and inlet metal concentration for both metal ions. Also, it was observed that there was an optimum flow rate of 1.4 mL min⁻¹ (surface loading of 0.792 cm min⁻¹) for both metal ions in the column. Results from both single and binary systems showed the adsorption capacity of C. indica for both metal ions increases with the increasing inlet concentration of each component and C. indica had a stronger affinity for uranium than nickel ions. The binary system results showed that the presence of the second component affected the adsorption of the first one by C. indica so the antagonistic action was observed. Also, the inhibitory effect of uranium ions on the nickel adsorption was greater than nickel ions on the uranium adsorption. The uranium and nickel breakthrough curves under different conditions were described by the Thomas, Yoon-Nelson and Yan models. Among these models, the Yan model appeared to describe the experimental results better.     

Effect of Constant Glucose Feeding on the Production of Exopolysaccharides by <Emphasis Type="Italic">Tremella fuciformis</Emphasis> Spores

A fed-batch culture system with constant feeding (glucose 80 g L⁻¹, 0.25 ml min⁻¹) was used to study the influence of glucose on cell dry weight and exopolysaccharides production from submerged Tremella fuciformis spores in a 5-L stirred-tank bioreactor. The results showed that high levels of cell mass (9.80 g L⁻¹) and exopolysaccharides production (3.12 g L⁻¹) in fed-batch fermentation were obtained after 1 h of feeding, where the specific growth rate (μ) and exopolysaccharides yield on substrate consumed (YP/S) were 0.267 d⁻¹ and 0.14 g g⁻¹. Unlike batch fermentation, maximal cell mass and exopolysaccharides production merely reached 7.11 and 2.08 g L⁻¹; the specific growth rate (μ) and exopolysaccharides yield on substrate consumed (YP/S) were 0.194 d⁻¹ and 0.093 g g⁻¹, respectively. It is concluded that the synthesis of exopolysaccharides can be promoted effectively when feeding glucose at a late exponential phase.     

Application of a quartz crystal nanobalance and principal component analysis for the detection and determination of histidine

The aim of the present investigation was to develop a biosensor based on a quartz crystal nanobalance (QCN) for the detection of histidine (His). A thin layer of nickel was electrochemically deposited over the gold crystal electrode and exposed to H₂O₂ to form nickel oxide. The composite electrode was then used to determine His. The frequency shifts were linear with respect to the concentration of His in solution. His can be measured in the range of 100–2000 mg L⁻¹. A lower limit of detection of 48 mg L⁻¹ and a sensitivity factor of 0.0307 Hz/mg L⁻¹ was obtained. Some possible interferences were checked for, and the performance of the sensor was found to be unaffected by any interference except for those from arginine, cysteine and NaH₂PO₄. Principal component analysis (PCA) was used to process the frequency response data of the single piezoelectric crystal at various times, considering the different adsorption–desorption dynamics of His and the interfering compounds. Over 85% of the variance in the data was explained by two principal components. A score plot of the data for the first two PCs showed that the modified QCN yields favorable identification and quantification performances for His and the interfering compounds.