TiO2-SiO2 monolithic glass formation from sol-gel

This study demonstrates that hydrolysis should be carried out in a step manner in gel synthesis. The key to the increase in the amount of water added is the control of the hydrolysis rate of Ti(OC₄H₉)₄. The hydrolysis of Si(OC₂H₅)₄ can be carried out at about 75°C. The amount of added water (γ_WI), which varied with TiO₂ content (in mol%), was about 64–88% of the total amount of added water. The hydrolysis reaction should be performed at room temperature while Ti(OC₄H₉)₄ is added. The total amount of added water (γ_W) is related to the amount of solvent (R). For example, if TiO₂ is 40mol%, γ_W will vary from 3.2 to 8.0 when R varies from 0.8 to 2.0. The amount of added water was affected by the distribution of solvent in the metal alkoxides. The amount of added water can be increased when R_Si(OC2H5)4 = 1, R_Ti(OC4H9)4 > 1. The rate of rise in temperature of the thermolysis of the dried gel should be less than 10°C per hour, and the heat treatment temperatyre is related to the TiO₂ content (in mol%). Gel glasses without devitrification can only be obtained by thermolysis at 600°C from the gel with no less than 20 mol% TiO₂.     

NMR studies of Na2O---B2O3---SiO2 glasses of mid-alkali content

¹¹B Fourier transform spectra have been used to study the structure of Na₂O---B₂O₃---SiO₂ glasses of mid-alkali content. Based on the measurements of the fraction N₄ of four-coordinated borons, it has been found that for K = mol.% SiO₂/mol.% B₂O₃ 8 and R = mol.% Na₂O/mol.% B₂O₃ = 1, N₄ is obviously smaller than 1 rather than equal to 1 as assumed in the relevant literature. Only when R reaches a value appropriately greater than 1, can the case where N₄ = 1 occur. A structural model suggested in this paper can satisfactorily explain the fact.     

Epitaxial growth of CuInSe2 single crystal by halogen transport method

CuInSe₂ single crystals were epitaxially grown on (001) GaP, (001) GaAs, and (110) GaP by the halogen transport method. The orientation relationships in the growth on the (001) and (110) faces were (a) [001]_CuInSe2 [001]_sub and [100]_CuInSe2 [100]_sub (c-axis orientation growth), and (b) [110]_CuInSe2 [110]_sub and [001]_CuInSe2 [001]_sub, respectively. On (001) InP, the orientation relationships between the layer and substrate consist of two sets: (c) [100]_CuInSe2 [001]_sub and [001]_CuInSe2 [010]_sub, and (d) [100]_CuInSe2 [001]_sub and [001]_CuInSe2 [ 00]_sub (a-axis orientation growth). The above results, i.e., c-axis growth on (001) GaP and (001) GaAs and a-axis growth on (001) InP, could be explained by a criterion of the minimum lattice mismatch between grown layers and substrates. A series of growth experiments on (001) GaAs indicated that appropriate gas etching of the substrate surface and growth temperature were required for obtaining twin-free single-crystal epitaxial CuInSe₂.     

Synthesis of Y2O3:Eu phosphors by bicontinuous cubic phase process

A novel approach for preparation of red-emitting europium-doped yttrium oxide phosphor (Y₂O₃:Eu) by using the bicontinuous cubic phase (BCP) process was reported in this paper. The BCP system was composed of anionic surfactant sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and aqueous yttrium nitrate/europium nitrate solution. Energy dispersive spectrometer analysis revealed the homogeneous precipitation occurred in the BCP structure. Thermogravimetric analysis measurements indicated the precursor powder was europium-doped yttrium hydroxide, Y_1−xEu_x(OH)₃. Scanning electron microscopy micrographs showed the precursor powder had a primary size about 30 nm and narrow size distribution. After heat treatment in furnace above 700 °C for 4 h, high crystallinity Y₂O₃:Eu phosphors was obtained. However, the primary size of particles grew to 50–200 nm and the dense agglomerates with a size below 1 μm were formed. X-ray diffraction patterns indicated the crystal structure of precursor powders and Y₂O₃:Eu phosphors were amorphous and body-centered cubic structure, respectively. The photoluminescence analysis showed that the obtained Y₂O₃:Eu phosphor had a strong red emitting at 612 nm and the quenching started at a Eu concentration of 10 mol%. This study indicated that the BCP process could be used to prepare the highly efficient oxide-based phosphors.     

Al2O3-TiO2 and Al2TiO5 ceramic materials by the sol-gel process

Ceramic materials with a very low thermal expansion coefficient are synthesized by the sol-gel process. The binary gel is obtained by hydrolysis and polycondensation reactions of organometallic compounds of aluminium and titanium. The thermal evolution of the amorphous powder is followed by DTA and TGA measurements. Structural evolution is followed using X-ray diffraction. The crystallization of the TiO₂ rutile and Al₂O₃ corindon starts at 700 and 900°C respectively. The transformation of Al₂O₃ and TiO₂ into Al₂TiO₅ appears between 1200 and 1300°C. The densification of the powder is performed by the hot pressing process. The shrinkage of the powder was previously followed by dilatometric measurements. The physical properties of the final material are studied as a function of pressing parameters.     

XAS study of lanthanum coordination environments in glasses of the system K2O---SiO2---La2O3

The La L₁ and L₃ XANES and L₃ EXAFS have been investigated for the series of glasses 10K₂O---50SiO₂---x La₂O₃ (x = 1, 5, 10) and (10 − x)K₂O---40SiO₂−(x/3)La₂O₃ (x = 7.5, 5, 2.5) and model compounds La₂O₃, LaAlO₃, LaPO₄, La₂NiO₄, La₂CuO₄ and La(OH)₃. An edge resonance at 25 eV above the L₁ edge in the glass spectra is concentration-dependent, decreasing in intensity with increasing lanthanum concentration. The 2s → nd forbidden transition increases with La₂O₃ concentration, indicating a reduction in the ‘average’ site symmetry of the first coordination shell of La. Mapping _X(k) space, which is a new and promising technique, was employed to extract bond distance, coordination number and thermal parameters from the EXAFS. By this method, one calculates the complete _X(k) space a function of all physically reasonable values of the adjusted parameters in all possible combinations. The advantage in this method is the assurance of a global minimum. Bond lengths were comparable to those obtained by Fourier transforming the phase corrected EXAFS. The values are 2.42 Å (± 0.03 Å) for La---O. The coordination numbers (N ≤ 7 ± 1.5) were derived by mapping and comparison to the published structures for other La compounds. _X(k) mapping is compared with least-squares fitting the data, and the correlation between the Debye-Waller factor and coordination number is also discussed.     

B NMR investigations in xV2O5–B2O3 and xV2O5–B2O3–PbO glasses

11B (I=3/2) MAS NMR in the binary glass system xV₂O₅–B₂O₃ (x=0.053, 0.43) and the ternary glass system xV₂O₅–B₂O₃–PbO (0.1x1.5) has been investigated at room temperature. In the xV₂O₅–B₂O₃ glasses, one NMR line due to BO₃ unit was observed. Meanwhile in the xV₂O₅–B₂O₃–PbO, two NMR lines which arise from BO₃ and BO₄ units were detected, where the appearance of BO₄ units is produced by the presence of PbO. From the computer-simulation of the ¹¹B NMR central transition line (m=−1/2↔1/2), the quadrupole parameters (e²qQ/h and η) for BO₃ units in xV₂O₅–B₂O₃, and those for BO₃ and BO₄ units in xV₂O₅–B₂O₃–PbO were obtained as a function of x. As the V₂O₅ content increases in xV₂O₅–B₂O₃–PbO, the e²qQ/h and η values of the BO₃⁻ associated resonance are found to slightly decrease and increase, respectively. Meanwhile, the e²qQ/h and η values of BO₄⁻ associated resonance in xV₂O₅–B₂O₃–PbO are found to slightly increase and decrease, respectively. By comparing the intensities of the total transitions (m=−3/2↔−1/2,m=−1/2↔1/2, and 1/2↔3/2) for the ¹¹B NMR line of BO₃ and BO₄ units contained in xV₂O₅–B₂O₃–PbO with those of respective standard samples of 0.053V₂O₅–B₂O₃ and NaBH₄, the quantitative fractions of BO₃ and BO₄ in xV₂O₅–B₂O₃–PbO were obtained as a function of x.     

Toughened glass-ceramics containing ZrO2 and Al2O3 prepared by the sol-gel process from metal alkoxides

Glasses of compositions 5ZrO₂·5SiO₂(ZS), 5ZrO₂·Al₂O₃·4SiO₂(ZAS) and 5 5ZrO₂·0.5Al₂O₃·0.5Na₂O·4SiO₂(ZANS) were prepared by the sol-gel process from metal alkoxides and sintered to make glass-ceramics. Tetragonal ZrO₂ was precipitated by heat treatment at 900 to 1300°C. The activation energy for tetragonal ZrO₂ crystal growth was extremely high in Al₂O₃ containing glasses. ZAS and ZS were sintered to the near theoretical densities above 1200°C, at which the predominant phase was tetragonal ZrO₂. On the other hand, for ZANS, high densification was not attained owing to the large pores enclosed by the glass phase. Strength and fracture toughness increased with the densification and the crystal growth of tetragonal ZrO₂, reaching 450 MPa and 9 MN/m^1.5, respectively.     

Ambient-condition growth of superconducting YBa2Cu4O8 single crystals using KOH flux

YBa₂Cu₄O₈ is a stoichiometric oxide superconductor of T_c80 K. Unlike YBa₂Cu₃O_7−δ, this compound is free from oxygen vacancy or twin formation and does not have any microscopic disorder in the crystal. Doping with Ca raises its T_c to 90 K. The compound is a promising superconductor for technological application. Up to now, single crystals have not been grown without using specialized apparatus with extremely high oxygen pressure up to 3000 bar and at over 1100 °C due to the limited range of reaction kinetics of the compound. This fact has delayed the progress in the study of its physical properties and potential applications. We present here a simple growth method using KOH as flux that acts effectively for obtaining high-quality single crystals in air/oxygen at the temperature as low as 550 °C. As-grown crystals can readily be separated from the flux and exhibit a perfect orthorhombic morphology with sizes up to 0.7×0.4×0.2 mm³. Our results are reproducible and suggest that the crystals can be grown using a conventional flux method under ambient condition.     

Multilayer SiO2 and TiO2 coatings on glasses by the sol-gel process

Glass films of pure SiO₂ and TiO₂ have been prepared on sodalime silica flat slide glasses by the sol-gel process using the dip-coating technique from TEOS and Ti(OC₃H₇)₄ solutions. The various parameters such as chemicals concentrations, viscosity, type of catalyst, withdrawal speed and temperature of densification leading to the obtention of good and adherent coatings with definite film thicknesses are reported. The same technique has been used for the depositon of layers of colored films SiO₂---M_xO_y (M = Co, Mn, Nd and Cr). Brilliant yellow coatings have been obtained with TiO₂---CeO₂.     

金红石型Ti1-2xCrxMoxO2黑色色料制备及其性能研究

以TiO₂、Cr₂O₃和MoO₃为主要原料,采用固相反应法合成了金红石型Ti_1-2xCr_xMo_xO₂(x=0、0.05、0.10、0.15、0.20)色料。研究了Cr/Mo共掺杂量和煅烧温度对Ti_1-2xCr_xMo_xO₂色料的晶型结构、呈色性能和微观形貌等的影响。研究结果表明,5%~15%摩尔分数的Cr/Mo等量共掺杂都获得单相金红石型结构黑色色料,均可促进锐钛矿向金红石转变,且Mo掺杂有利于提高Cr在TiO₂晶格中的固溶度。随Cr/Mo共掺杂量增加,样品的黑度(L^*值)呈先减小后增大的趋势,而红色度(a^*值)和黄色度(b^*值)都表现出相反的趋势。煅烧温度在950~1 100 ℃时,样品的色度参数变化相对较小。在1 100 ℃煅烧得到的Ti_0.70Cr_0.15Mo_0.15O₂色料黑色呈色性能最佳,其L^*、a^*和b^*值分别为24.41、2.12和-2.53,且在陶瓷釉中表现出良好的呈色性能和化学稳定性。适量Cr/Mo共掺杂使TiO₂晶格产生畸变和电荷缺陷,从而吸收绝大部分可见光,是其呈现黑色的主要原因。     

Study on the Ce substitution effects of BiFeO3 films on ITO/glass substrates

Ce substituted Bi_1−xCe_xFeO₃ (BCFO) films with x=0–0.15 were deposited on indium tin oxide (ITO)/glass substrates by sol–gel process annealed at 500 °C. Rhombohedral phase was confirmed by XRD study and no impure phases were observed till x=0.15. Substantially enhanced ferroelectricity was observed at room temperature due to the substitution of Ce. In the films with x=0.05 and 0.10, the double remnant polarization are 75.5 and 57.7 μC/cm² at an applied field 860 kV/cm. Moreover, the breakdown field was enhanced in the films with Ce substitution.     

Vapor phase epitaxy of pure VO2 and V1−xCrxO2

The vapor phase epitaxy of thin epilayers of VO₂ and V_1−xCrxO₂ on TiO₂ transparent substrates is described. Chemical vapor deposition occurs by reacting a (VOCL₃/CrO₂Cl₂/H₂O/H₂) mixture at about 800°C using argon as a carrier gas. The preparation of pure VO₂ requires special care to make it homogeneously stoichiometric and to obtain steep concentration profiles at the TiO₂/VO₂ interface. Layers were obtained which had electrical and optical properties comparable to the best bulk crystals grown by other techniques. Homogeneous solid solutions of V_1−xCr_xO₂ epilayers were also grown for the first time in the range o < x < 0.17. Chromium concentration and homogeneity were determined by electron microprobe analysis. The separation coefficient k was also found to vary with x. It is close to unity below x = 0.001 and above this value Cr is incorporated more easily. High quality heteroepitaxial layers (1 cm² area, 1 to 30 μm thickness) of V_1−xCr_xO₂ have for the first time allowed the measurement of the optical absorption coefficient.     

Ti3(ZnxAl1-x)C2固溶体热学、电学和力学性质的理论研究

采用第一性原理的密度泛函理论平面波赝势法, 通过投影缀加波(PAW)和广义梯度近似(GGA)系统地研究了Ti₃(Zn_xAl_1-x)C₂的结构、能量、声子性质、电子性质和弹性性质。对MAX相Ti₃AlC₂晶体中A位置的Al元素用Zn元素进行替换掺杂,构建出Ti₃(Zn_xAl_1-x)C₂(x=0,0.25,0.5,0.75,1)固溶体结构模型。计算分析表明:在所研究的掺杂浓度范围内Ti₃(Zn_xAl_1-x)C₂均是热力学、动力学和力学稳定的脆性材料;此外,Ti₃(Zn_xAl_1-x)C₂(x=0,0.25,0.5,0.75,1)均呈现金属性,在费米能级处的电子态密度主要贡献来自Ti-3d态,同时具有离子键、共价键和金属键的综合性质。随着Zn原子掺杂浓度的增加,在一定程度上其导电性和塑性均增强。     

Ab initio study of NMR spectra of Li2S–SiS2 glass system

We obtained the chemical shielding constants of ²⁹Si in Li₂S–SiS₂ glass system on the basis of molecular orbital calculations. The relative chemical shieldings calculated at the HF/6-31G* level is −16.1 and −23.8 ppm for E(1) and E(0), respectively. These calculations are in good agreement with the previous NMR study: σ(E(2))>σ(E(1))>σ(E(0)). It is found theoretically that incorporation of Li₂S into SiS₂ does not influence the ²⁹Si chemical shift, while incorporation of Li₂O into SiO₂ does to a significant extent. It is also found that the existence of oxygen in Li₂S–SiS₂ glasses increases the chemical shielding of ²⁹Si by about 25 ppm, which is in good agreement with the experimental result.     

Hydrolysis and condensation reactions of Si(OC2H5)4 related to silica fiber drawing

The hydrolysis and condensation reactions of Si(OC₂H₅)₄ (TEOS) at 80°C in the TEOS---H₂O---C₂H₅OH---HCl solutions with H₂O/TEOS molar ratios (r) from 1.0 to 2.0 were followed by gas chromatography (GC) and measurement of molecular weight ( ) of the hydrolyzates, in order to explain the viscosity change of the solutions. It has been found that the siloxane oligomers with average polymerization degree (n) from 2 to 7 are formed in the early stage of reaction and undergo condensation to form higher polymers. The n and the number of silanol groups of the oligomers are increased with increasing r. The fact that the solution viscosity increased once rapidly around the so-called gelation point followed by a sluggish increase with the increase of reaction time for an r of 1.7, while it increased rapidly without a break till gelation for an r of 2.0, was attributed to fewer silanol groups and higher steric hindrance as a result of more −OC₂H₅ groups remaining in the oligomers for an r of 1.7.     

Synthesis, thermal and magnetic properties of new metal iodate: (LiFe1/3)(IO3)2

This paper reports the detail synthesis of a new kind of metal iodate, anhydrous (LiFe_1/3)(IO₃)₂, from aqueous solutions. The synthesized compound shows spinal morphology and is chemical stable up to 400°C. The iodate shows paramagnetic behavior from room temperature down to 4.2 K. At room temperature, the new compound has a hexagonal structure with the lattice parameters a=5.4632(2) Å, c=5.0895(6) Å, Z=1, space group of P6₃.     

Edge-defined film-fed growth of Yb:YVO4 single crystal plates

The applicability of the edge-defined film-fed growth (EFG) technique for Yb_xY_(1−x)VO₄ (x=0.05, 0.1 and 1) was approved by successful growth of crystals up to 80 mm in length as the thin plates. Low-angle grain boundaries and the crystal coloration as main defects were found. Optimal seed orientation was suggested on the strength of vanadate crystal plate morphology. Optical properties, chemical composition and the crystalline quality were investigated.     

Growth of NaBi(WO4)2 crystal by modified-Bridgman method

NaBi(WO₄)₂ (NBW) crystals have been grown for the first time by modified-Bridgman method. Influences of some factors on the crystal growth process are discussed. X-ray powder diffraction experiments show that the unit cell parameters of NBW crystal are a=b=0.5284 nm, c=1.1517 nm, and V=0.3215 nm³. The differential thermal analysis shows that the NBW crystal melts at 923°C.     

Characterisation of semiconducting V2O5–Bi2O3–TeO2 glasses through ultrasonic measurements

Tellurite containing vanadate (50−x)V₂O₅–xBi₂O₃–50TeO₂ glasses with different bismuth (x=0, 5, 10, 15, 20 and 25 wt%) contents have been prepared by rapid quenching method. Ultrasonic velocities (both longitudinal and shear) and attenuation (for longitudinal waves only) measurements have been made using a transducer operated at the fundamental frequency of 5 MHz in the temperature range from 150 to 480 K. The elastic moduli, Debye temperature, and Poisson’s ratio have been obtained both as a function of temperature and Bi₂O₃ content. The room temperature study on ultrasonic velocities, attenuation, elastic moduli, Poisson’s ratio, Debye temperature and glass transition temperature show the absence of any anomalies with addition of Bi₂O₃ content. The observed results confirm that the addition of Bi₂O₃ modifier changes the rigid formula character of TeO₂ to a matrix of regular TeO₃ and ionic behaviour bonds (NBOs). A monotonic decrease in velocities and elastic moduli, and an increase in attenuation and acoustic loss as a function of temperature in all the glass samples reveal the loose packing structure, which is attributed to the instability of TeO₄ trigonal bipyramid units in the network as temperature increases. It is also inferred that the glasses with low Bi₂O₃ content are more stable than with high Bi₂O₃ content.