随机粗糙微通道内流动特性研究

采用计算流体动力学的方法, 研究了微通道内气体在速度滑移和随机表面粗糙度耦合作用下的流动特性. 其中, 利用二阶速度滑移边界条件描述气体的边界滑移, 利用分形几何学建立随机粗糙表面. 研究发现, 综合考虑二阶速度滑移边界条件和随机表面粗糙度在较大的平均Knudsen数范围内 (0.025-0.59) 得到的计算结果与实验数据符合得很好, 而一阶速度滑移边界条件只在平均Knudsen数较小时(<0.1)符合实验结果. 随机表面粗糙度对气体在边界处的滑移有显著影响, 相对粗糙度越大, 速度滑移系数越小. 并针对计算结果, 给出了滑移系数与相对粗糙度近似满足的关系. 随机粗糙表面对气体流动过程中的压强、速度、Poiseuille数也有显著影响. 关键词： 随机表面粗糙度 二阶速度滑移边界条件 分形 微通道     

粗糙纳通道内流体流动与传热的分子动力学模拟研究

为研究粗糙表面对纳尺度流体流动和传热及其流固界面速度滑移与温度阶跃的影响,本文建立了粗糙纳通道内流体流动和传热耦合过程的分子动力学模型,模拟研究了粗糙通道内流体的微观结构、速度和温度分布、速度滑移和温度阶跃并与光滑通道进行了比较,并分析了固液相互作用强度和壁面刚度对界面处速度滑移和温度阶跃的影响规律. 研究结果表明,在外力作用下,纳通道主流区域的速度分布呈抛物线分布,由于流体流动导致的黏性耗散使得纳通道内的温度分布呈四次方分布. 并且,在固体壁面处存在速度滑移与温度阶跃. 表面粗糙度的存在使得流体剪切流动产生了额外的黏性耗散,使得粗糙纳通道内的流体速度水平小于光滑通道,温度水平高于光滑通道,并且粗糙表面的速度滑移与温度阶跃均小于光滑通道. 另外,固液相互作用强度的增大和壁面刚度的减小均可导致界面处速度滑移和温度阶跃程度降低. 关键词： 速度滑移 温度阶跃 流固界面 粗糙度     

纳米通道粗糙内壁对流体流动行为的影响

纳米流动系统具有高效、经济等优势,在众多领域具有广泛的应用前景.因该类系统具有极高的表面积体积比,致使界面滑移效应对流动具有显著影响.本文采用分子动力学方法以两无限大平行非对称壁面组成的Poiseuille流动为对象,分析了壁面粗糙度与润湿性变化对通道内流体流动的影响.对于不同结构类型的壁面,需要通过水动力位置来确定固液界面位置,准确计算固液界面位置有助于更好地分析界面滑移效应.研究结果表明,上下壁面不对称会引起通道内流场参数分布的不对称,壁面粗糙度及润湿性的变化会影响近壁面附近流体原子的流动特性,由于壁面凹槽的存在,粗糙壁面附近的数密度分布低于光滑壁面一侧.壁面粗糙度及润湿性的变化会影响固液界面位置,肋高变化及壁面润湿性对通道中速度分布影响较大,界面滑移速度及滑移长度随肋高和润湿性的增大而减小;肋间距变化对通道内流体流动影响较小,界面滑移速度和滑移长度基本保持恒定.     

等离子弧焊接熔池演变过程的模拟和验证

本文建立了描述等离子弧焊接熔池相变传热与流动的三维数理模型,考虑表面张力、电磁力和浮升力的作用,并针对等离子弧焊接特点,改进组合式体积热源模型,上部采用双椭球热源,下部采用圆锥体热源。重点分析了焊接熔池形状和温度场的演变过程,熔合线的模拟形状与实验焊缝吻合,较好地呈现了焊缝的凸起和熔池宽度,验证了数学模型和热源模型的正确性。本文还进一步开展了焊接功率和焊接速度的影响分析。研究结果表明,流动对焊缝形状的影响不容忽略,而表面张力在三个流动驱动力中占主导地位;焊接功率越大,焊接速度越小,越有利于焊件焊透,数值模拟得到优化的焊接功率和速度有益于实际焊接生产质量及效率。     

由于表面粗糙引起的激光声表面波色散的实验和理论研究

表面粗糙是材料制造过程中必有的副产物, 粗糙表面会引起其中传播的声表面波的速度发生变化. 在利用激光声表面波对材料性质进行评估时, 常用宽带的激光声表面波速度频散特性对材料性质进行反演. 为了研究表面粗糙度是否能作为反演的特征参数之一, 本文建立了激光在表面粗糙样品中激发声表面波、聚偏氟乙烯换能器宽带接收声表面波的实验装置来研究不同粗糙度表面对声表面波速度的影响; 理论上建立了激光在粗糙表面中激发声表面波的计算模型, 利用有限元法得到声表面波的时域特征, 并进一步得到声表面波的速度色散曲线, 理论结果和实验结果能很好地拟合. 这为利用激光声表面波对表面粗糙的评估提供理论和实验依据. 关键词： 表面粗糙 激光声表面波 速度色散 聚偏氟乙烯传感器 有限元法     

Investigation of transient processes at liquid boiling under nonstationary heat generation conditions

The paper presents results on experimentally investigated dynamics of boiling development and formation of film boiling zones under stepwise heat generation on a horizontally and vertically oriented cylindrical surface in a large volume of Freon-21. Experimental data on the expectation time and boiling temperature, the propagation velocity and structure of evaporation and boiling fronts for different heat flux density both in saturated liquid and in subcooling conditions are obtained. Results of experiments on investigating the nucleation forms under development of nonstationary heat release crisis caused by heat loading on the vertical heater immersed into the volume of liquid (water, ethanol) subcooled to saturation temperature are presented. A calculation ratio for determining the expectation time to the beginning of intense vaporization in water is proposed and compared with experimental data obtained on surfaces with different-size roughness. Peculiarities of evolution of evaporation fronts from incipient bubbles are investigated in the experiments with ethanol. Data on the evaporation front velocity as a function of wall overheating are obtained. The obtained experimental data on the propagation velocity of self-sustained evaporation fronts are compared with the known calculated data.     

粗糙平板微通道流动和传热的数值模拟

以粗糙平行平板微通道为研究对象,以三角形锯齿状粗糙元模拟固体表面的粗糙度,采用CFD流体固体共轭传热技术数值研究了绝对粗糙度和相对粗糙度对平行平板微通道流动和传热特性的影响,着重分析了粗糙度和流体速度对水力入口段长度和热力入口段长度的影响规律,同时研究了相对粗糙度对微通道转捩雷诺数的影响,为进一步揭示微微通道的流动和传热机理提供了依据.     

Three-dimensional turbulent flow over cube-obstacles

In order to investigate the influence of surface roughness on turbulent flow and examine the wall-similarity hypothesis of Townsend, three-dimensional numerical study of turbulent channel flow over smooth and cube-rough walls with different roughness height has been carried out by using large eddy simulation(LES) coupled with immersed boundary method(IBM). The effects of surface roughness array on mean and fluctuating velocity profiles, Reynolds shear stress, and typical coherent structures such as quasi-streamwise vortices(QSV) in turbulent channel flow are obtained. The significant influences on turbulent fluctuations and structures are observed in roughness sub-layer(five times of roughness height).However, no dramatic modification of the log-law of the mean flow velocity and turbulence fluctuations can be found by surface cube roughness in the outer layer. Therefore, the results support the wall-similarity hypothesis. Moreover, the von Karman constant decreases with the increase of roughness height in the present simulation results. Besides, the larger size of QSV and more intense ejections are induced by the roughness elements, which is crucial for heat and mass transfer enhancement.     

Heat transfer and friction in rectangular solar air heater duct having spherical and inclined rib protrusions as roughness on absorber plate

In this work, an experimental investigation on heat and fluid flow characteristics of artificially roughened solar air heater duct has been carried out. The roughness and operating parameters covered a range of Reynolds number (Re) from 2000 to 20000, relative roughness pitch (P/e) from 15 to 30, relative rib length (r/g) from 0.4 to 1.0, and relative rib pitch (P_r/P) from 0.2 to 0.8. Other parameters, i.e., relative roughness height (e/D), angle of attack (α), and relative roughness gap are kept constant. Results show that the considerable enhancement in Nusselt number and Thermo-hydraulic performance has been obtained with an increase in friction factor using roughened surface.     

Survey on nucleate pool boiling of nanofluids: the effect of particle size relative to roughness

Pool boiling heat transfer using nanofluids (which are suspensions of nano-sized particles in a base fluid) has been a subject of many investigations and incoherent results have been reported in literature regarding the same. In the past, experiments were conducted in nucleate pool boiling with varying parameters such as particle size, concentration, surface roughness etc. and all sort of results ranging from heat transfer enhancement, deterioration and no effect were reported. This work tries to segregate a survey on pool boiling of nanofluids with respect to particle concentration. This is due to the fact that a major drift in heat transfer behavior is observed at higher and lower particle concentration. But upon deep perusal it has been found that deterioration in heat transfer coefficient are mainly observed at higher particle concentrations (4–16% by weight) and enhancements mainly at lower particle concentrations (0.32–1.25% by weight). Moreover, the relative size of the particle with respect to the surface roughness of the heating surface seems to play an important role in understanding the boiling behaviour. Also, recent works have reported that change in ‘surface wetting’ of the heating surface due to nanofluids and the formation of a porous layer modifiying nucleation site density can be of importance in predicting nucleate pool boiling characteristics of nanofluids. In the present paper, attempts are made to make systematic analysis of results in literature and try to bring out a common understanding of the results in literature.     

高温壁面液体射流冲击瞬态沸腾传热的实验研究

以水作为冷却介质,对高温壁面在射流冲击淬冷时的瞬态换热特性进行了实验研究,获得了介质在不同过冷度、不同射流速度下的完整沸腾曲线。实验结果表明。无论是增大工质过冷度还是提高射流速度,总会使得热壁面的冷却速率加大。在一定的过冷度和射流速度下壁温变化呈现快－慢－快的特点。临界热流密度随平均壁温变化率的增大而增大,二者之间存在线性关系．     

Direct experimental evidence of slip in hexadecane: solid interfaces

The boundary condition for the flow velocity of a Newtonian fluid near a solid wall has been probed experimentally with a novel setup using total internal reflection-fluorescence recovery after photobleaching leading to a resolution from the wall of the order of 80 nm. For hexadecane flowing on a hydrocarbon/lyophobic smooth surface, we give what we think to be the first direct experimental evidence of noticeable slip at the wall. We show that the surface roughness and the strength of the fluid-surface interactions both act on wall slip, in antagonist ways.     

Nanoparticle transport effect on magnetohydrodynamic mixed convection of electrically conductive nanofluids in micro-annuli with temperature-dependent thermophysical properties

This is a numerical investigation of nanoparticle transport effect on magnetohydrodynamic mixed convective heat transfer of electrically conductive nanofluids in micro-annuli with temperature-dependent thermophysical properties. The modified Buongiorno's non-homogeneous model is applied for the nanoparticle-fluid suspension to simulate the migration of nanoparticles into the base fluid, originating from the thermophoresis (nanoparticle migration because of temperature gradient) and Brownian motion (nanoparticle slip velocity because of concentration gradient). Due to surface roughness at the solid–fluid interface in micro-annuli, the wall surfaces are subjected to a linear slip condition to assess the non-equilibrium region near the interface. The fluid flow has been assumed to be fully developed, and the governing equations including continuity, momentum, energy, and nanoparticle transport equation are reduced to a system of ordinary differential equations, before they have been solved numerically. The results are presented with and without considering the dependency of thermophysical properties upon the temperature. It is indicated that ignoring the temperature dependency of thermophysical properties does not significantly affect the flow fields and heat transfer behavior of nanofluids, but it changes the relative magnitudes. Furthermore, in the presence of magnetic field, smaller nanoparticles are more appropriate than larger ones.     

Experimental investigation of a flowing fluid layer on metal surface roughness measurement and aberration correction using adaptive optics

The induced optical aberration of laser beam passing through a transparent flowing fluid layer on a metal specimen is experimentally and empirical formula studied. The proposed study presents an experimental investigation of metal surface roughness measurement by combining an optical probe of laser-scattering phenomena and adaptive optics (AO) for aberration correction. In the absence of the AO correction scheme, induced flow velocity of 0.278 m/s can severely degrade the residual wavefront root mean square (RMS) error to 0.58 μm and decrease the scattered laser intensity. Real-time AO correction in closed-loop at a sampling rate of 8Hz can reduce the wavefront RMS error to 0.19 μm and improve the attenuation of scattered laser intensity. The maximum relative error of the estimated roughness (R _a) is less than 7.8% compared with the stylus method. The experimental results show satisfactory correction in the presence of a flowing fluid layer using the AO system.     

半干旱草原下垫面动量和感热总体输送系数参数化关系研究

本文利用锡林郭勒草原2008年春季近地层涡旋相关系统和铁塔的风、 温平均梯度观测资料, 分析了总体输送系数随梯度Richardson数的变化特征, 建立了动量总体输送系数随大气稳定度、近地层风速以及感热总体输送系数随大气稳定度和近地层气温的关系. 中性条件下, 半干旱草原植被下垫面动量总体输送系数与近地层大气动力状态之间存在明显的相互作用, 总体输送系数与近地面层风速之间满足二次曲线拟合关系; 风速较小时, 大气动力特征对地表粗糙度长度的改变不是很明显, 动量总体输送系数随气流增强而增大; 而当风速较大时, 强风速会使植被高度发生改变, 动量总体输送系数随气流增强而减小. 另外, 感热总体输送系数与近地层气温之间也存在二次曲线关系. 动量总体输送系数与近地层风速之间的关系、感热总体输送系数与近地层气温之间关系的建立为总体输送系数参数化提供了重要途径, 同时该方案避免了对动力学粗糙度长度和热力学粗糙度长度的求解. 关键词： 总体输送系数 参数化 湍流通量 相似性函数     

高超声速可压缩流中粗糙壁热流研究

用计算流体力学（CFD）数值模拟和理论方法对高超声速可压缩湍流中粗糙壁面热增量进行研究. 着重考虑粗糙单元密度和粗糙单元形状对粗糙表面热流的影响. 结果表明： ①粗糙单元密度变化时, CFD数值方法计算所得的粗糙单元等效热流随着粗糙单元密度的降低而增加, 理论方法预测结果的规律随方法不同而不同;②在相同粗糙单元密度和高度时,如果粗糙单元形状改变,CFD计算结果也随之发生改变. 理论预测方法所得结果不发生变化.     

Micromagnetic analysis of current-driven DW dynamics along rough strips with high perpendicular anisotropy at room temperature

Domain-wall motion along thin ferromagnetic strips with high perpendicular magnetocrystalline anisotropy driven by spin-polarized currents is theoretically analyzed by means of full micromagnetic simulations and one-dimensional model, both including surface roughness and thermal effects. At finite temperature, the results show a current dependence of the domain wall velocity in good qualitative agreement with available experimental observations, depicting a low-current, low velocity creep regime, and a high-current, linear regime separated by a smeared depinning region. The analysis points out the relevance of both thermal fluctuations and surface roughness on the domain wall dynamics, and confirms that these effects are essential to get a better understanding on the origin, the role and the magnitude of the non-adiabaticity by direct comparison with experiments.     

Heat Transfer in an Upper Convected Maxwell Fluid with Fluid Particle Suspension

An analysis is carried out to study the magnetohydrodynamic (MHD) flow and heat transfer characteristics of an electrically conducting dusty non-Newtonian fluid, namely, the upper convected Maxwell (UCM) fluid over a stretching sheet. The stretching velocity and the temperature at the surface are assumed to vary linearly with the distance from the origin. Using a similarity transformation, the governing nonlinear partial differential equations of the model problem are transformed into coupled non-linear ordinary differential equations and the equations are solved numerically by a second order finite difference implicit method known as the Keller-box method. Comparisons with the available results in the literature are presented as a special case. The effects of the physical parameters on the fluid velocity, the velocity of the dust particle, the density of the dust particle, the fluid temperature, the dust-phase temperature, the skin friction, and the wall-temperature gradient are presented through tables and graphs. It is observed that, Maxwell fluid reduces the wall-shear stress. Also, the fluid particle interaction reduces the fluid temperature in the boundary layer. Furthermore, the results obtained for the flow and heat transfer characteristics reveal many interesting behaviors that warrant further study on the non-Newtonian fluid flow phenomena, especially the dusty UCM fluid flow phenomena.     

Perturbation technique for unsteady MHD mixed convection periodic flow, heat and mass transfer in micropolar fluid with chemical reaction in the presence of thermal radiation

An analytical study is presented for the problem of unsteady hydromagnetic heat and mass transfer for a micropolar fluid bounded by semi-infinite vertical permeable plate in the presence of first-order chemical reaction, thermal radiation and heat absorption. A uniform magnetic field acts perpendicularly to the porous surface which absorbs the micropolar fluid with a time-dependent suction velocity. The basic partial differential equations are reduced to a system of nonlinear ordinary differential equations which are solved analytically using perturbation technique. Numerical calculations for the analytical expressions are carried out and the results are shown graphically. The effects of the various dimensionless parameters related to the problem on the velocity, angular velocity, temperature and concentration fields are discussed in detail.     

Effects of uniform surface roughness on vortex-induced vibration of towed vertical cylinders

The present study was motivated by a desire to understand the vortex-induced vibration (VIV) of cylindrical offshore structures such as spars in strong currents. In particular, the consequences of marine growth on the surface as well as natural surface roughness that occurs with years in service are studied. Of special interest is the effect of surface roughness on the response amplitudes and the forces experienced by these structures while undergoing VIV.The experimental apparatus employed for the present study consisted of an elastically mounted rigid vertical cylinder with no end plates, towed along the length of a water tank. The cylinder was attached to a parallel linkage mechanism allowing motion in the transverse direction only. The cylinder surface was covered by sandpapers with known mean particle diameters, thus providing controlled values of roughness coefficient from 0.28×10⁻³ to 1.38×10⁻². The tests covered the subcritical range of Reynolds number from 1.7×10⁴ to 8.3×10⁴, and a reduced velocity range from 4 to 16.It was found that as the roughness of the cylinder was increased the maximum response amplitude and the maximum mean drag coefficient decreased, levelling off to constant values. The onset of lock-in was progressively delayed for rougher cylinders, and the width of the lock-in region showed remarkable reduction at higher roughness values. The Strouhal number was found to display a modest increase with roughness. The dynamic mean drag of the rough cylinders was also found to be lower than that for a smooth cylinder. It is felt that uniform roughness such as caused in marine environments may act favorably to lower VIV incidence and effects in the range of Reynolds number tested.