用激光干涉法诊断准分子激光在YBa_2Cu_3O_(7-δ)靶面激励等离子体的电子密度

利用激光标准干涉法诊断了准分子激光(XeCl,308 nm)在YBa_2Cu_3O_(7-σ)超导靶面激励等离子体的电子密度.结果表明在入射激光功率密度为3×10~8W/cm~2,本底真空度为1.33～13.3 Pa的条件下,等离子体电子密度为10~(16)～10~(17)/cm~3.     

激光等离子体能量角分布及吸收定标律

主要研究激光平面靶等离子体发射能量角分布及吸收定标律。实验利用高斯型1.06μm激光脉冲,其能量为2～50J,脉冲宽度为0.3～2.2ns,靶面平均辐照强度为1.8×1013～1.1x10~(15)W/cm~2,光束以25°角入射。实验采用了Au、Ag、Ti、Al和C_8H_8等厚靶。用等离子体卡计测量靶面吸收的激光能量。用指数函数拟合实验数据,给出了吸收效率分别作为激光强度、脉冲宽度和靶材料原子序数的函数的定标关系式。这些关系式定性地与逆轫致吸收的理论关系式相一致。     

蒸汽羽等离子体对入射激光吸收的研究

继用高速摄影技术对自由振荡钕玻璃激光与Ly12铝靶相互作用产生的蒸汽羽的传播及其特性进行研究之后,又定量研究了它的吸收屏蔽效应。实验表明,在0.7～1.6×10~7W/cm~2的激光功率密度下,其光学厚度最高可达1.2。蒸汽羽等离子体对入射激光的吸收与辐照靶的功率密度成正比,在距靶面3mm处比9mm处吸收强。实验获得了吸收随序列尖峰脉冲时间的变化曲线。     

长脉冲激光辐照LY—12铝靶烧蚀表面的后退速度

用烧穿靶法测量自由振荡长脉冲 1.06μm会聚激光束烧蚀LY-12铝合金靶时间,用电子微量天平、金相显微仪、收集器等测量激光烧蚀铝靶材参量Am和h的技术,给出激光束烧蚀铝靶的烧蚀表面后退速度和烧蚀速度的结果。当烧蚀靶材的激光通量I=10~5～10~7W/cm~2时,烧蚀表面后退速度为0.5～3.8m/s,烧蚀速度为 1～8g/s。     

全息术诊断激光产生蒸汽羽等离子体

介绍了用脉冲激光全息二次曝光法诊断Q开关钕玻璃激光脉冲与LY12铝靶(φ50×3)耦合产生蒸汽羽等离子体的原理和实验。在打靶激光脉宽约50ns,功率密度约5GW/cm~2条件下,拍摄了激光产生蒸汽羽等离子体的全息干涉图。运用Abel变换和Saha方程,对全息干涉图进行数据处理,得到对激光与物质相互作用机理研究的有用参数。     

“多靶串接”饱和增益软X光激光实验研究

采用“多靶串接”设计,利用强度为0.8×10~(13)～1.0×10~(13)W/cm~2,波长为1.05μm,脉宽约1ns的两路钕玻璃激光线聚焦辐照四块串接的平面厚锗靶,观察到波长为23.2和23.6nm的接近饱和的类Ne锗软X光激光输出。当总靶长为5.6cm时,这两种波长的软X光激光输出的GL值都达到16左右,沿靶法线和靶平面方向的发散角都只有3～4mrad。     

脉冲激光引起金属靶板层裂的阈值条件

本文考虑单脉冲激光作用于金属靶引起的应力波单次反射导致层裂的阈值条件,包括激光通量与应力波强度的定标关系、应力波传播时的衰减、入射波与反射波相互作用以及不同层裂判据的比较。本文结果指出,对于一定的激光通量和靶板厚度,只有一定范围内的激光脉宽才能造成层裂,最低激光通量则对应于最佳激光脉宽。本文的方法和结论也适合于飞片撞击造成的层裂现象。     

脉冲激光作用下铝靶的层裂

 本文报导波长为1.06 μm脉宽（FWHM）约4 ns的强脉冲激光辐照下，铝靶发生层裂的实验结果。当入射功率密度在2.0×10¹¹~5×10¹¹ W/cm²范围的激光束作用下，厚度为0.1 mm、0.2 mm的靶在超临界条件下发生层裂，层裂厚度分别在(17±6) μm及(35±5) μm范围。文中使用一种简化模型对阈值条件下不同厚度的靶发生层裂时的层裂片厚度作了近似估算，并与已有的实验结果较好地符合。     

蒸汽羽等离子体对入射激光吸收的研究

继用高速摄影技术对自由振荡钕玻璃激光与Ly12铝靶相互作用产生的蒸汽羽的传播及其特性进行研究之后,又定量研究了它的吸收屏蔽效应。实验表明,在0.7～1.6×10~7W/cm^2的激光功率密度下,其光学厚度最高可达1.2。蒸汽羽等离子体对入射激光的吸收与辐照靶的功率密度成正比,在距靶面3mm处比9mm处吸收强。实验获得了吸收随序列尖峰脉冲时间的变化曲线。     

线状聚焦激光与金属作用的离子速度分布

本文报道了利用法拉第筒飞行时间法进行的离子测量.通过比较高功率激光线状聚焦和点状聚焦在平面金属靶上产生的离子发射特性,总结出离子速度分布和激光辐照密度的定标规律,以及离子速度分布的空间各向异性.实验是在上海光机所钕玻璃激光装置上进行的,激光束的波长为1.06μm,脉宽为300ps,辐照密度为10~(12)～10~(14)W/cm~2.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.