Kinetic spectrophotometric determination of submicromolar orthophosphate by molybdate reduction

A kinetic spectrophotometric procedure was developed for determination of submicromolar orthophosphate based on the reaction in which orthophosphate serves as a catalyst in the reduction of molybdenum, and the initial rate of molybdenum-blue formation (λ_max = 780 nm) is proportional to the concentration of orthophosphate in the samples. The detection limit (3 × standard deviation of blank, n = 8) was 6 nM and the linear calibration ranged from 10 to 100 nM (r² = 0.997). The precisions of this method were 3.3% at 10 nM and 5.4% at 50 nM (n = 8), respectively. Similar to other molybdate based methods, silica and arsenate in the samples can interfere with phosphate determination. The responses of silicate and arsenate were about 25% and 7% of that of orthophosphate, respectively, and their interferences were enhanced in the presence of phosphate in the samples due to the synergistic effect of phosphate with arsenate or silicate on the molybdate reagent.     

Interference from arsenate when determining phosphate by the malachite green spectrophotometric method

The effect of arsenate on phosphate determination by the malachite green spectrophotometric method was investigated. The molar absorptivities of the molybdophosphate and malachite green–molybdoarsenate species at 625 nm and a final acidity of 0.38 M were calculated as 10.4±0.13×10⁴ and 7.2±0.17×10⁴ l mol⁻¹ cm⁻¹ respectively, indicating that arsenate could interfere in phosphate measurement. Arsenate concentrations as low as 23 μg l⁻¹ caused increase in colour development in phosphate solutions. However, the extent of colour development for both anions depended on the final acid concentration of the solution. An acidified sodium sulphite solution (0.83 M NaSO₃, 0.83 M H₂SO₄) quantitatively prevented arsenate colour development up to 300 μg l⁻¹ As(V). It was also demonstrated that the method removed As(V) interferences in mixed As/P solutions and therefore can be used to treat natural water samples with elevated arsenate concentrations before phosphate measurement.     

Spectrophtometric determination of malachite green in fish farming water samples after cloud point extraction using nonionic surfactant Triton X-100

A novel and sensitive cloud point extraction procedure for the determination of trace amounts of malachite green by spectrophotometry was developed. Malachite green was extracted at pH 2.5 mediated by micelles of nonionic surfactant Triton X-100. The extracted surfactant-rich phase was diluted with ethanol and its absorbance was measured at 630 nm. The effect of different variables such as pH, Triton X-100 concentration, cloud point temperature and time and diverse ions was investigated and optimum conditions were established. The calibration graph was linear in the range of 4-500 ng mL⁻¹ of malachite green in the initial solution with r = 0.9996 (n = 10). Detection limit based on three times the standard deviation of the blank (3S_b) was 1.2 ng mL⁻¹ and the relative standard deviation (R.S.D.) for 20 and 300 ng mL⁻¹ of malachite green was 1.48 and 1.13% (n = 8), respectively. The method was applied to the determination of malachite green in different fish farming and river water samples.     

孔雀绿与磷钒钼杂多酸显色反应的研究

在稀H2SO4介质中,磷酸盐与钼酸盐和偏钒酸盐反应形成磷钒钼杂多酸,杂多酸再与孔雀绿缔合形成四元有色络合物,能稳定存在于含聚乙烯醇的水溶液中。缔合物的最大吸收位于590nm波长处,摩尔吸收系数ε=1.7×105L·mol-1·cm-1,P(V)的质量浓度在0～0.12μg mL范围内与吸光度成正比。研究了显色反应的适宜条件、共存离子的影响和缔合物的组成。方法已用于合成试样中磷的测定。     

Development of a PRiME cartridge purification method for rapid determination of malachite green and leucomalachite green in Chinese softshell turtle

A high‐throughput PRiME (process, robustness, improvements, matrix effects, ease of use) sample purification procedure was developed to simplify the multiple steps of traditional SPE in extracting the malachite green and leucomalachite green in Chinese softshell turtle (Pelodiscus sinensis). The sample loading volume, extracting solvent type, and pH value of the employed PRiME hydrophilic‐lipophilic balance cartridge for sample purification were optimized to be 3 mL, acetonitrile, and pH 5, respectively. In comparison with traditional SPE, the PRiME process is cost‐effective, solvent‐saving, and simple to operate, which only consists of a passing through step without traditional sorbent conditioning and impurity washing. Afterward, eluate was analyzed by ultra‐performance liquid chromatography‐tandem mass spectrometry, and the proposed method was validated for linearity (R² > 0.9992), intraday precision (2.44–3.22%), interday precision (3.28–6.58%), sensitivity (LOD ≤ 0.18 μg/kg and, LOQ ≤ 0.60 μg/kg), and recovery (88.7–94.1%, RSD < 6.79%). The results indicated that the PRiME technique can simplify the sample preparation procedure by avoiding the tedious steps, such as conditioning, washing, etc. It would be of significant interest for environmental and food safety applications in the market of Chinese softshell turtle and related products.     

Preconcentration and spectrophotometric determination of low concentrations of malachite green and leuco-malachite green in water samples by high performance solid phase extraction using maghemite nanoparticles

A novel and sensitive extraction procedure using maghemite nanoparticles (γ-Fe₂O₃) modified with sodium dodecyl sulfate (SDS), as an efficient solid phase, was developed for removal, preconcentration and spectrophotometric determination of trace amounts of malachite green (MG) and leuco-malachite green (LMG). Combination of nanoparticle adsorption and easily magnetic separation was used to extraction and desorption of MG and LMG. The adsorption capacity was evaluated using both the Langmuir and Freundlich adsorption isotherm models. Maghemite nanoparticles were prepared by co-precipitation method and their surfaces were modified by SDS. The size and properties of the produced maghemite nanoparticles was determined by X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) and BET analysis. MG and LMG became adsorbed at pH 3.0. LMG was oxidized to MG by adsorption on maghemite nanoparticles. The adsorbed MG was then desorbed and determined spectrophotometrically. The calibration graph was linear in the range 0.50-250.00 ng mL⁻¹ of MG and LMG with a correlation coefficient of 0.9991. The detection limit of the method for determination of MG was 0.28 ng mL⁻¹ and the relative standard deviation (R.S.D.) for 10.00 and 50.00 ng mL⁻¹ of malachite green was 1.60% (n = 3) and 0.86% (n = 5), respectively. A preconcentration factor of 50 was achieved in this method. The Langmuir adsorption capacity (q_max) was found to be 227.3 mg g⁻¹ of the adsorbent. The method was applied to the determination of MG in fish farming water samples.     

Removal of cationic methylene blue and malachite green dyes from aqueous solution by waste materials of Daucus carota

In present study adsorption capacity of waste materials of Daucus carota plant (carrot stem powder: CSP and carrot leaves powder: CLP) was explored for the removal of methylene blue (MB) malachite green (MG) dye from water. The morphology and functional groups present were investigated by scanning electron microscope (SEM) and Fourier transform infrared (FTIR) spectroscopy. The operating variables studied were pH, adsorbent dose, ionic strength, initial dye concentration, contact time and temperature. Equilibrium data were analysed using Langmuir and Freundlich isotherm models and monolayer adsorption capacity of adsorbents were calculated. Kinetic data were studied using pseudo-first and pseudo-second order kinetic models and the mechanism of adsorption was described by intraparticle diffusion model.Various thermodynamic parameters such as enthalpy of adsorption ΔH°, free energy change ΔG° and entropy ΔS° were estimated. Negative value of ΔH° and negative values of ΔG° showed that the adsorption process was exothermic and spontaneous. Negative value of entropy ΔS° showed the decreased randomness at the solid–liquid interface during the adsorption of MB and MG onto CSP and CLP.     

Multi-pumping flow system for the determination of dissolved orthophosphate and dissolved organic phosphorus in wastewater samples

A multi-pumping flow system (MPFS) for the spectrophotometric determination of dissolved orthophosphate and dissolved organic phosphorus in wastewater samples is proposed. The determination of orthophosphate is based on the vanadomolybdate method. In-line ultraviolet photo-oxidation is employed to mineralise organic phosphorus to orthophosphate prior to detection. A solenoid valve allows the deviation of the flow towards the UV-lamp to carry out the determination of organic phosphorus.Calibration was found to be linear up to 20 mg P L⁻¹, with a detection limit (3s_b/S) of 0.08 mg P L⁻¹, an injection throughput of 75 injections h⁻¹ and a repeatability (R.S.D.) of 0.6% for the direct determination of orthophosphate. On the other hand, calibration graphs were linear up to 40 mg P L⁻¹, with a detection limit (3s_b/S) of 0.5 mg P L⁻¹, an injection throughput of 11 injections h⁻¹ and a repeatability (R.S.D.) inferior to 2.3% for the procedures involving UV photo-oxidation.     

酶联免疫吸附分析法测定水产品及水中孔雀石绿和无色孔雀石绿

本文报道一种同时测定水产品及水样中孔雀石绿(MG)和无色孔雀石绿(LMG)的间接竞争酶联免疫吸附分析法。对无色孔雀石绿分子进行修饰,使其与载体蛋白交联,得到免疫原和包被抗原,经过多次免疫动物制得抗无色孔雀石绿的多克隆抗体。在优化的实验条件下,IC50值(标准曲线中吸光度抑制至最大吸光度值的50%时所对应的待测物浓度)为0.9~2.6μg/L,检出限为0.02~0.10μg/L,无色孔雀石绿在水样及水产品中的回收率为76.2~95.0%,与孔雀石绿的交叉反应率为95.25%。真实样品测定中,两种食用鱼养殖水样及一个鱼样中未检出孔雀石绿和无色孔雀石绿,但在观赏鱼养殖水样及另一鱼样中检出孔雀石绿和无色孔雀石,浓度分别为1.84μg/L和1.38μg/L。     

孔雀石绿共振光散射法测定饮用水中痕量BrO3-

在pH3.8的HAc-NaAc缓冲液中,BrO3-氧化I-生成I2,I2与过量的I-反应生成I3-,I3-与孔雀石绿(MG)反应形成缔合微粒,导致体系的共振光散射强度急剧增强,最大共振光散射波长位于465nm处,BrO3-浓度在0～120μg/L范围内有较好线性关系,检出限以3σ计算为3.4ng/mL,据此建立了一种测定微量BrO3-的共振光谱新方法.该法用于饮用水中BrO3-的测定,得到了满意的结果.     

Development of cloud point extraction using pH-sensitive hydrogel for preconcentration and determination of malachite green

A novel and sensitive cloud point extraction procedure using pH-sensitive hydrogel was developed for preconcentration and spectrophotometric determination of trace amounts of malachite green (MG). In this extraction method, appropriate amounts of poly(styrene-alt-maleic acid), as a pH-sensitive hydrogel, and HCl were added respectively into the aqueous sample so a cloudy solution was formed. The cloudy phase consists of hydrogel particles distributed entirely into the aqueous phase. Organic or inorganic compounds having the potential to interact with polymer particles (chemical interaction or physical adsorption) could be extracted to cloudy phase. After centrifuging, these particles of hydrogel were sedimented in the bottom of sample tube. The sedimented hydrogel-rich phase was diluted with acetonitrile and its absorbance was measured at 617 nm (λ_max of malachite green in hydrogel). Central composite design and response surface method were applied to design the experiments and optimize the experimental parameters such as, concentration of hydrogel and HCl, extraction time and salting out effect. Under the optimum conditions, the linear range was 1 × 10⁻⁸-5 × 10⁻⁷ mol L⁻¹ malachite green with a correlation coefficient of 0.992. The limit of detection (S/N = 3) was 4.1 × 10⁻⁹ mol L⁻¹. Relative standard deviation (RSD) for 7 replicate determinations of 10⁻⁷ mol L⁻¹ malachite green was 3.03%. In this work, the concentration factor of 20 was reached. Also the improvement factor of the proposed method was 23. The advantages of this method are simplicity of operation, rapidity and low cost.     

溴酸钾氧化孔雀石绿和甲基橙褪色光度法测定水中亚硝酸根

在H3PO4介质中,利用痕量NO2-催化KBrO3氧化孔雀石绿和甲基橙褪色的反应,建立了双波长双指示剂催化动力学光度法测定痕量NO2-的新方法。该反应在最大吸收峰505nm和615nm处,催化和非催化体系吸光度的变化与NO2-浓度呈线性关系,线性范围为0.01～0.80μg/mL,检出限为1.3×10-3μg/mL,该方法用于环境水样(自来水、雨水、延安卷烟厂废水)中痕量NO2-的测定,加标回收率为97%～110.2%.     

Flow-through solid-phase based optical sensor for the multisyringe flow injection trace determination of orthophosphate in waters with chemiluminescence detection

In this work, a novel flow-through solid-phase based chemiluminescence (CL) optical sensor is described for the trace determination of orthophosphate in waters exploiting the multisyringe flow injection analysis (MSFIA) concept with multicommutation. The proposed time-based injection flow system relies upon the in-line derivatisation of the analyte with ammonium molybdate in the presence of vanadate, and the transient immobilisation of the resulting heteropolyacid in a N-vinylpyrrolidone/divinylbenzene copolymer packed spiral shape flow-through cell located in front of the window of a photomultiplier tube. The simultaneous injection of well-defined slugs of luminol in alkaline medium and methanol solution towards the packed reactor is afterwards performed by proper switching of the solenoid valves. Then, the light emission from the luminol oxidation by the oxidant species retained onto the sorbent material is readily detected. At the same time, the generated molybdenum-blue compound is eluted by the minute amount of injected methanol, rendering the system prepared for a new measuring cycle. Therefore, the devised sensor enables the integration of the solid-phase CL reaction with elution and detection of the emitted light without the typical drawbacks of the molybdenum-blue based spectrophotometric procedures regarding the excess of molybdate anion, which causes high background signals due to its self-reduction. The noteworthy features of the developed CL-MSFIA system are the feasibility to accommodate reactions with different pH requirements and the ability to determine trace levels of orthophosphate in high silicate content samples (Si/P ratios up to 500). Under the optimised conditions, a dynamic linear range from 5 to 50 μg P l⁻¹ for a 1.8 ml sample, repeatability better than 3.0% and a quantification limit of 4 μg P l⁻¹ were attained. The flowing stream system handles 11 analysis h⁻¹ and has been successfully applied to the determination of trace levels of orthophosphate in environmental samples such as mineral, ground, tap and pond waters as well as samples from a water-steam cycle of an incineration plant. The t-test comparison of the means for the developed optical sensor and the molybdenum-blue spectrophotometric APHA/AWWA/WPCF reference method revealed that there is no evidence of significant differences between the obtained results at the 95% confidence level.     

A simple linear sweep voltammetric method for the determination of double-stranded DNA with malachite green

In pH 3.5 Britton—Robinson buffer solution double-stranded (ds) DNA can react with malachite green (MG) to form an interaction complex, which resulted in the decrease of the electrochemical response of MG, MG had a well-defined second-order derivative linear sweep voltammetric peak at −0.73 V (vs. SCE). After the addition of dsDNA into MG solution, the reductive peak current decreased with the positive shift of peak potential, which was the typical characteristic of intercalation. Based on the interaction, an indirect electrochemical determination method for dsDNA was established. The optimum conditions for the reaction were investigated and there were little or no interferences from the commonly coexisting substances. The decrease of peak current was linear with the concentration of dsDNA over the range of 0.8–12.0 μg cm⁻³ with the linear regression equation as ΔI _p″/nA = 91.70 C/(μg cm⁻³) + 74.55 (n = 10, γ = 0.990). The detection limit was calculated as 0.46 μg cm⁻³ (3σ). The method had high sensitivity and was further applied to the dsDNA synthetic samples with satisfactory result. The interaction mechanism was discussed with the intercalation of DNA-MG to form a supramolecular complex and the stoichiometry of the supramolecular complex was calculated by electrochemical method with the binding number 3 and the binding constant 2.35 × 10¹⁵ (mol dm⁻³)⁻³.     

Production of malachite green oxalate and leucomalachite green reference materials certified for purity

Malachite green oxalate (MG oxalate) and leucomalachite green (LMG) have been prepared and certified as pure reference materials. The purities of MG oxalate and LMG were assessed by high-performance liquid chromatography–diode array detection (HPLC–DAD), nuclear magnetic resonance (NMR) spectroscopy, differential scanning calorimetry (DSC), Karl Fischer titration, ashing and thermogravimetric analysis (TGA). MG oxalate was purified by supercritical fluid extraction (SFE). Prior to purification, commercial MG oxalate purity was estimated to be about 90%. The main impurities present in SFE-purified MG oxalate were identified and quantified using HPLC–DAD. The main impurities were found to be monode-MG (monodemethylated MG oxalate synthesis impurity), 4-(dimethylamino)benzophenone (4-DMABP), MG-carbinol and LMG. The homogeneity of both reference materials was also determined. Issues associated with the stability of LMG and MG oxalate in solution forced an extensive study investigating different parameters i.e. solvent, acid, analyte concentration and temperature. MG oxalate (100 μg/mL) was found to be stable in acetonitrile containing 1% v/v glacial acetic acid for at least 155 days and LMG (100 μg/mL) was stable in acetonitrile for at least 133 days. The final purity value for MG oxalate was 94.3 ± 1.4% m/m at the 95% confidence interval (or 67% m/m if MG cation is reported). For LMG, the certified purity was found to be 98.8 ± 0.8% m/m at the 95% confidence interval. Figure Calibration reference materials for malachite green and leucomalachite green, certified for purity, are essential in characterising these key analytes in a fish matrix reference material     

Fast and sensitive trace analysis of malachite green using a surface-enhanced Raman microfluidic sensor

A rapid and highly sensitive trace analysis technique for determining malachite green (MG) in a polydimethylsiloxane (PDMS) microfluidic sensor was investigated using surface-enhanced Raman spectroscopy (SERS). A zigzag-shaped PDMS microfluidic channel was fabricated for efficient mixing between MG analytes and aggregated silver colloids. Under the optimal condition of flow velocity, MG molecules were effectively adsorbed onto silver nanoparticles while flowing along the upper and lower zigzag-shaped PDMS channel. A quantitative analysis of MG was performed based on the measured peak height at 1615 cm⁻¹ in its SERS spectrum. The limit of detection, using the SERS microfluidic sensor, was found to be below the 1–2 ppb level and this low detection limit is comparable to the result of the LC-Mass detection method. In the present study, we introduce a new conceptual detection technology, using a SERS microfluidic sensor, for the highly sensitive trace analysis of MG in water.     

Oxidation of crystal violet and malachite green in aqueous solutions — a kinetic spectrophotometric study

The reactions of two triphenyl methane (TPM) dyes—crystal violet (CV⁺) and malachite green (MG⁺)—with N₃^• and OH^• radicals were studied by pulse radiolytic kinetic spectrophotometry. The rate constants for the reaction of the cationic dyes (D⁺) with N₃^• are (9.0±0.6)×10⁹ and (3.0±0.2)×10⁹ dm³ mol⁻¹ s⁻¹ respectively and those for the reaction with OH^• are obtained as (8.0±0.6)×10⁹ and (1.1±0.1)×10⁹ dm³ mol⁻¹ s⁻¹ respectively. The transient spectra resulting from the oxidation of the dyes were characterized. The time-resolved spectra indicate that the reaction with OH^• radicals initially generates an adduct which subsequently dissociates to form the radical dication D^•2+. The D^•2+ species decay by further reaction with the parent dye.     

The molybdenum blue reaction for the determination of orthophosphate revisited: Opening the black box

The molybdenum blue reaction, used predominantly for the determination of orthophosphate in environmental waters, has been perpetually modified and re-optimised over the years, but this important reaction in analytical chemistry is usually treated as something of a 'black box' in the analytical literature. A large number of papers describe a wide variety of reaction conditions and apparently different products (as determined by UV–visible spectroscopy) but a discussion of the chemistry underlying this behaviour is often addressed superficially or not at all. This review aims to rationalise the findings of the many 'optimised' molybdenum blue methods in the literature, mainly for environmental waters, in terms of the underlying polyoxometallate chemistry and offers suggestions for the further enhancement of this time-honoured analytical reaction.     

A sensitive flow-injection method for determination of trace amounts of nitrite

A new sensitive colour reaction for nitrite determination is presented. In acidic medium, nitrite was reacted with safranine to form a diazonium salt which caused the reddish-orange dye colour of the solution to change to blue. The carrier stream, into which the sample solution was injected, was doubly distilled water. The reagent solution stream, which contained safranine dye, hydrochloric acid and potassium chloride, was mixed with the carrier in a 3-m length of silicon tubing (bore 0.5 mm) maintained at 30°C in a thermostatic bath. The absorbance intensity was measured at 520 nm. The detection limit was 20 ng ml⁻¹ and the RSD% of 20 injections of 1 μg ml⁻¹ of nitrite was 0.65%. Analysis can be done at a rate of up to 30 h⁻¹. Under the optimum conditions in the concentration range of 30–4000 ng ml⁻¹ of nitrite ion, a linear calibration graph was obtained (r=0.9999). The method was applied successfully to the determination of nitrite in sausages.     

Electrochemical determination of malachite green using a multi-wall carbon nanotube modified glassy carbon electrode

A multi-wall carbon nanotube (MWNT) film-modified electrode is described for the determination of malachite green (MG). The electrochemical profile of MG was examined using cyclic voltammetry (CV) and differential pulse voltammetry (DPV), suggesting that the MWNT film facilitates the electron transfer of MG in terms of a potential shift and then significantly enhances the oxidation peak current of MG. The experimental parameters, such as supporting electrolyte, thickness of MWNT film, scan rate and accumulation time, were optimized. Consequently, a sensitive and convenient electrochemical method is proposed for the determination of MG. The oxidation peak current is proportional to the concentration of MG over the range from 5.0 × 10⁻⁸ to 8.0 × 10⁻⁶ mol L⁻¹ obeying the following equation: i_p = 0.09 + 1.19 × 10⁷ C (r = 0.995, i_p in μA, C in mol L⁻¹). The detection limit is 6.0 × 10⁻⁹ mol L⁻¹ (signal to noise = 3) after 5 min of accumulation. Moreover, this method possesses good reproducibility (RSD is 5.6%, n = 8) as well as long-term stability. Finally, the new method was employed to determine MG in fish samples. Correspondence: W. Huang, Department of Chemistry, Hubei Institute for Nationalities, Enshi 445000, P.R. China