Continuous determination of total flavonoids in Platycladus orientalis (L.) Franco by dynamic microwave-assisted extraction coupled with on-line derivatization and ultraviolet-visible detection

This paper describes a new method for the determination of total flavonoids in Platycladus orientalis (L.) Franco. The method was based on dynamic microwave-assisted extraction (DMAE) coupled with on-line derivatization and ultraviolet-visible (UV-vis) detection. The influence of the experimental conditions was tested. Maximum extraction yield was achieved using 80% aqueous methanol of extraction solvent; 80 W of microwave output power; 5 min of extraction time; 1.0 mL min⁻¹ of extraction solvent flow rate. The derivatization reaction between aluminium chloride and flavonoid is one of the most sensitive and selective reactions for total flavonoids determination. The optimized derivatization conditions are as follows: derivatization reagent 1.5% aluminium chloride methanol solution; reaction coil length 100 cm; derivatization reagent flow rate 1.5 mL min⁻¹. The detection and quantification limits obtained are 0.28 and 0.92 mg g⁻¹, respectively. The intra-day and inter-day precisions (R.S.D.) obtained are 1.5% and 4.6%, respectively. Mean recovery is 98.5%. This method was successfully applied to the determination of total flavonoids in P. orientalis (L.) Franco and compared with heat reflux extraction. The results showed that the higher extraction yield of total flavonoids was obtained by DMAE with shorter extraction time (5 min) and small quantity of extraction solvent (5 mL).     

The determination of organochlorine pesticides based on dynamic microwave-assisted extraction coupled with on-line solid-phase extraction of high-performance liquid chromatography

A rapid technique based on dynamic microwave-assisted extraction coupled with on-line solid-phase extraction of high-performance liquid chromatography (DMAE-SPE-HPLC) has been developed. A TM₀₁₀ microwave resonance cavity built in the laboratory was applied to concentrate the microwave energy. The sample placed in the zone of microwave irradiation was extracted with 95% acetonitrile (ACN) aqueous solution which was driven by a peristaltic pump at a flow rate of 1.0 mL min⁻¹. The extraction can be completed in a recirculating system in 10 min. When a number of extraction cycles were completed, the extract (1 mL) was diluted on-line with water. Then the extract was loaded into an SPE column where the analytes were retained while the unretained matrix components were washed away. Subsequently, the analytes were automatically transferred from the SPE column to the analytical column and determined by UV detector at 238 nm. The technique was used for determination of organochlorine pesticides (OCPs) in grains, including wheat, rice, corn and bean. The limits of detection of OCPs are in the range of 19-37 ng g⁻¹. The recoveries obtained by analyzing the four spiked grain samples are in the range of 86-105%, whereas the relative standard deviation (R.S.D.) values are <8.7% ranging from 1.2 to 8.7%. Our method was demonstrated to be fast, accurate, and precise. In addition, only small quantities of solvent and sample were required.     

Ultrasonic nebulization extraction coupled with on-line gas chromatography for determination of trans-anethole in spices

Ultrasonic nebulization extraction (UNE) coupled with on-line gas chromatography (GC) was proposed for the determination of trans-anethole in fruits of Illicium verum Hook. f. and Foeniculum vulgare Mill. The extraction was performed in a common self-made extraction system. In the UNE the analyte was transferred and enriched from the solid sample to gas phase. The sample gas containing analyte obtained by UNE was introduced into the sampling loop with the purging gas (N₂). And then the sample gas in the sampling loop was introduced into the GC column. Several experimental parameters of on-line UNE-GC, including sampling time, flow rate of purging gas, standstill time and temperature of tubing, were optimized. The calibration curve ranging from 0.05 to 1.5 mg g⁻¹ for determining the trans-anethole was obtained. The recoveries for determining trans-anethole are between 99.2% and 111.2% and RSDs are less than 8.3% when the UNE was applied. The analytes can rapidly be extracted and transferred from the solid sample to gas phase. The analytes in the gas phase are easier to be introduced into GC system than those in the solid and liquid phase. Compared with off-line systems, the proposed on-line system is more suitable to detect volatile compounds.     

Determination of total flavonoids in Scutellaria barbata D. Don by dynamic ultrasonic extraction coupled with on-line spectrophotometry

A dynamic ultrasonic extraction (DUE) coupled with on-line detection by spectrophotometry is proposed for the determination of total flavonoids (calculated against scutellarin) in Scutellaria barbata D. Don. The extraction was performed in a common self-made extraction vessel put in an ultrasonic bath and a peristaltic pump was used to deliver the extraction solvent. Several experimental parameters of DUE, including flow rate and concentration of extraction solvent, ultrasonic power and sample amount, were optimized. In this work an on-line method was provided with the advantages of minimum sample amount (5 mg), on-line monitoring the extraction process and time saving (12.5 min). Compared with off-line method, the proposed method would be more convenient for obtaining continuous measurements and rapid optimization of the extraction process.     

动态超声萃取分光光度法在线测定红花中的总红花黄色素

用动态超声萃取分光光度法在线测定了红花中的红花黄色素, 对萃取条件进行了优化. 萃取与测定同时进行, 大大缩短了样品的分析时间, 简化了分析过程. 通过与静态超声萃取、振荡萃取和索式萃取进行比较, 不仅证明该方法耗时最短, 而且样品用量小, 萃取产率较高. 实际样品分析得到了满意的结果.     

Efficient synthesis of analogs of safflower yellow B, carthamin, and its precursor: two yellow and one red dimeric pigments in safflower petals

The synthesis of analogs (8, 12, 14) of two yellow pigments, safflower yellow B and the precursor of carthamin, and carthamin itself, a red pigment, which are produced in safflower (Carthamus tinctrious L.) petals and, which have a common dimeric quinochalcone structure, is reported. The key compound for the synthesis of these analogs, (p-hydroxycinnamoyl)filicinic acid (7) was synthesized in six steps from phloroglucinol in a total yield of 39%, which was reacted with 2,3,4,5,6-penta-O-acetyl-aldehydo-d-glucose, glyoxylic acid, and ethyl orthoformate in the presence of base to afford the corresponding analog, 8, 12, 14, in good yields, respectively. Precursor analog 12 was then converted to carthamin analog 14 by oxidative decarboxylation by treatment with potassium permanganate as well as the natural specimen.     

Static-dynamic pressurized hot water extraction coupled to on-line filtration-solid-phase extraction-high-performance liquid chromatography-post-column derivatization-fluorescence detection for the analysis of N-methylcarbamates in foods

A combination of static-dynamic modes of pressurized hot water extraction has been used for the extraction of N-methylcarbamates (namely, oxamyl, dioxacarb, metholcarb, carbofuran and carbaryl) from different fruits and vegetables. The selection of water as leaching agent provides a clean approach which avoids the use of organic solvents. A flow injection manifold coupled to the extractor has allowed the automation of the subsequent steps (namely, filtration, preconcentration, individual chromatographic separation, post-column derivatization and fluorescence detection) involved in the analytical process. Good recoveries, ranging from 80 to 104%, and precision, expressed as relative standard deviation, between 3.0 and 8.4% have been achieved by the proposed method.     

On-line continuous flow ultrasonic extraction coupled with high performance liquid chromatographic separation for determination of the flavonoids from root of Scutellaria baicalensis Georgi

An on-line method, based on coupling dynamic ultrasonic extraction (DUE), continuously sampling the suspension of sample and solvent, high performance liquid chromatographic separation with diode array detection, has been developed for the determination of the flavonoids, including baicalin, baicalein and wogonin, from the root of Scutellaria baicalensis Georgi. Variables influencing the DUE were evaluated by orthogonal test. The extraction yields of baicalin, baicalein and wogonin in the roots of S. baicalensis Georgi obtained from five different cultivated areas are 73.8–131.5 μg mg⁻¹ (RSD ≤ 6.24%), 6.8–15.9 μg mg⁻¹ (RSD ≤ 5.36%) and 4.4–14.3 μg mg⁻¹ (RSD ≤ 5.30%), respectively. The limits of detection for baicalin, baicalein and wogonin are 0.30, 0.37 and 0.41 μg mL⁻¹, respectively. Linearity is from 0.55 to 109 μg mL⁻¹ for baicalin, from 0.51 to 105 μg mL⁻¹ for baicalein and from 0.53 to 102 μg mL⁻¹ for wogonin. Compared with off-line continuous flow-DUE, the proposed method would be more convenient for the determination of the analytes and the rapid optimization of the extraction process. The extraction yields of flavonoids obtained by the proposed method are comparable with those obtained by dynamic microwave assisted extraction, static ultrasonic extraction and reflux extraction. The result indicated that the proposed method is suitable to determine the active components in Chinese herbal medicine.     

On-line coupling of dynamic microwave-assisted extraction to solid-phase extraction for the determination of sulfonamide antibiotics in soil

A rapid technique based on dynamic microwave-assisted extraction (DMAE) coupled on-line with solid-phase extraction (SPE) was developed for the determination of sulfonamides (SAs) including sulfadiazine, sulfameter, sulfamonomethoxine and sulfaquinoxaline in soil. The SAs were first extracted with acetonitrile under the action of microwave energy, and then directly introduced into the SPE column which was packed with neutral alumina for preconcentration of analytes and clean-up of sample matrix. Subsequently, the SAs trapped on the alumina were eluted with 0.3% acetic acid aqueous solution and determined by liquid chromatography-tandem mass spectrometry. The DMAE parameters were optimized by the Box-Behnken design. Maximum extraction efficiency was achieved using 320 W of microwave power; 12 mL of extraction solvent and 0.8 mL min⁻¹ of extraction solvent flow rate. The limits of detection and quantification obtained are in the range of 1.4-4.8 ng g⁻¹ and 4.6-16.0 ng g⁻¹ for the SAs, respectively. The mean values of relative standard deviation of intra- and inter-day ranging from 2.7% to 5.3% and from 5.6% to 6.7% are obtained, respectively. The recoveries of SAs obtained by analyzing four spiked soil samples at three fortified levels (20 ng g⁻¹, 100 ng g⁻¹ and 500 ng g⁻¹) were from 82.6 ± 6.0% to 93.7 ± 5.5%. The effect of standing time of spiked soil sample on the SAs recoveries was examined. The recoveries of SAs decreased from (86.3-101.9)% to (37.6-47.5)% when the standing time changed from one day to four weeks.     

Evaluation of vacuum microwave-assisted extraction technique for the extraction of antioxidants from plant samples

In the present work, vacuum microwave-assisted extraction (VMAE) was to perform microwave-assisted extraction in vacuum. Two well-known antioxidants, vitamin C from guava and green pepper, and vitamin E (α-tocopherol and γ-tocopherol) from soybean and tea leaves, which were easy to be oxidized, were chosen as representative target compounds for the evaluation of VMAE. The extraction yields of vitamin C, α-tocopherol and γ-tocopherol in VMAE and those in MAE performed in atmosphere (air-MAE) were compared and the effects of extraction time, extraction temperature and sample matrix were studied. Moreover, the effects of the oxygen and subpressure invacuo were also discussed via performed MAE in N₂ atmosphere (N₂-MAE). The extraction yields of vitamin C, α-tocopherol and γ-tocopherol in VMAE were higher than that in air-MAE, 35% increments of vitamin C from green pepper, 22% increments of α-tocopherol and 47% increments of γ-tocopherol from tea leaves were obtained, respectively. The comparable increased extraction yields of vitamin C, α-tocopherol and γ-tocopherol in N₂-MAE to that in air-MAE confirmed that oxygen in system was the crucial factor for the oxidation of vitamin C and vitamin E, VMAE was beneficial for the extraction of these oxygen-sensitive compounds. In addition, the subpressure invacuo in the VMAE system also showed positive affect on the extraction yields. On the basis of preventing oxidation and improving extraction efficiency of target compounds because of less oxygen and subpressure invacuo in the extraction system, VMAE has good potential for the extraction of oxygen-sensitive and thermosensitive compounds from plant samples.     

Development of microwave-assisted extraction followed by headspace solid-phase microextraction and gas chromatography-mass spectrometry for quantification of camphor and borneol in Flos Chrysanthemi Indici

In the work, microwave-assisted extraction (MAE) followed by headspace solid-phase microextraction (HS-SPME) and gas chromatography-mass spectrometry (GC-MS) was developed for quantitative analysis of the bioactive components of camphor and borneol in a traditional Chinese medicines (TCM) of Flos Chrysanthemi Indici. After systematical investigation, the optimal experimental parameters microwave power (400 W), irradiation time (4 min), fiber coating (PDMS/DVB fiber), extraction temperature (40 °C), extraction time (20 min), stirring rate (1100 rpm), and salt effect (no salt added) were investigated. The optimized method provided satisfactory precision (RSD values less than 12%), good recovery (from 86% to 94%), and good linearity (R² > 0.999). The proposed method was applied to quantitative analysis of camphor and borneol in Flos Chrysanthemi Indici samples from 11 different growing areas. To demonstrate the method feasibility, steam distillation was also used to analyze camphor and borneol in Flos Chrysanthemi Indici samples from these different growing areas. The very close results were obtained by the two methods. It has been shown that the proposed ME-HS-SPME-GC-MS is a simple, rapid, solvent-free and reliable method for quantitative analysis of camphor and borneol in TCM, and a potential tool for quality assessment of Flos Chrysanthemi Indici.     

Dynamic microwave-assisted extraction coupled on-line with solid-phase extraction: determination of polycyclic aromatic hydrocarbons in sediment and soil

This paper describes a new extraction tool for the determination of polycyclic aromatic hydrocarbons (PAHs) in soil and sediment samples, using dynamic microwave-assisted extraction combined with solid-phase extraction (DMAE-SPE). The critical variables for DMAE-SPE are investigated and optimized in an experimental design. The technique proved to be fast, accurate and able to yield quantitative extraction of PAHs from naturally contaminated sediment and soil samples. The set-up is fully automated and features monitored extraction, which facilitates rapid optimization of the method. In addition, only small quantities of solvent and sample are required.     

Direct determination of tagitinin C in Tithonia diversifolia leaves by on-line coupling of supercritical carbon dioxide extraction to FT-IR spectroscopy by means of optical fibres

Supercritical fluid extraction (SFE) with carbon dioxide as extraction medium was on-line coupled to a FT-IR spectrometer equipped with a Mercury Cadmium Telluride (MCT) detector using a tailor-made high-pressure fibre optic flow cell. This method was optimised and developed for the monitoring in real time and the quantification of dynamic extractions of tagitinin C from Tithonia diversifolia leaves.In order to demonstrate the method ability to allow the direct quantification of tagitinin C in the extract medium the standard addition method was used. The area integration of curves obtained by plotting the absorbance of the highly specific CO stretching vibration at 1668 cm⁻¹ versus time (i.e. extractograms) was used as instrumental response.The SFE/FT-IR process was successfully validated using the accuracy profile as decision tool. On this basis, a linear regression model was chosen for the calibration curve. The relative standard deviation for repeatability and intermediate precision were between 0.8 and 3.1 %, respectively. Moreover, the method was found to be accurate as the two-sided 95% beta-expectation tolerance interval did not exceed the acceptance limits of 85 and 115% on the analytical range investigated (500-2500 μg of added amount of tagitinin C).The proposed method allowed the non-destructive extraction of tagitinin C and its on-line quantitative determination in less than 25 min thus facilitating the subsequent experiments or the pharmacological studies performed on this compound.     

Flow-injection determination of phenylephrine hydrochloride in pharmaceutical dosage forms with on-line solid-phase extraction and spectrophotometric detection

A flow injection method is proposed for the determination of phenylephrine hydrochloride in pharmaceutical dosage forms. The method involves the use of on-line solid-phase extraction by means of a microcolumn containing Dowex 50W X8 ion-exchange resin for the separation of the analyte prior to colour development and spectrophotometric detection in the visible region.

The influence of preconcentration flow, preconcentration pH and elution volume was studied.

The method exhibits appropriate linearity (r² = 0.9999) which was proved statistically by means of the “F”-test. When applied to commercial samples containing several active ingredients and excipients, a significant reduction of interferences was found. Accuracy, evaluated by means of the spike recovery method was in the range 99.7–100.8%, with precision (R.S.D., %) better than 1%.

In order to achieve the automation the system was controlled from a notebook computer by means of a program written in QuickBASIC language. Under these conditions, a sampling frequency of 40 samples per hour could be attained.     

Continuous microwave-assisted extraction coupled on-line with liquid-liquid extraction: determination of aliphatic hydrocarbons in soil and sediments

This paper describes a new extraction method for the determination of aliphatic hydrocarbons (AHs) in soil and sediment samples, using continuous microwave-assisted extraction (MAE) combined with liquid-liquid extraction, for clean-up purposes. Analytical determinations were carried out by gas chromatography coupled with impact ionization mass spectrometry. The influence of the experimental conditions was tested using an agricultural soil spiked with standards (stored at 4 degrees C for 1 month) as reference soil. Maximum extraction efficiencies (80-90%) were achieved using 0.1-1.0g of sample, 60microl of water and 3ml of n-hexane (extractant) and 5min of extraction time; less than 70% of the most volatile hydrocarbons (C(9)-C(12)) were recovered since many evaporated during the drying step of the sample. MAE was compared with a conventional extraction method such as Soxhlet and a good agreement in the results was obtained (average recovery percentage value of 105% by comparing MAE against Soxhlet). Quality parameters such as linear range (0.5-800microg/g), limits of detection (LODs) (0.1-0.2microg/g) and precision (RSD, 4-6%) were determined using spiked soil samples. This method was successfully applied to the analysis of aliphatic hydrocarbons (C(9)-C(27) including pristane and phytane) in contaminated real samples.     

Ionic liquid-based microwave-assisted extraction of essential oil and biphenyl cyclooctene lignans from Schisandra chinensis Baill fruits

Ionic liquid-based microwave-assisted extraction (ILMAE) has been successfully applied in extracting essential oil and four kinds of biphenyl cyclooctene lignans from Schisandra chinensis Baill. 0.25 M 1-lauryl-3-methylimidazolium bromide ionic liquid is selected as solvent. The optimum parameters of dealing with 25.0 g sample are 385 W irradiation power, 40 min microwave extraction time and 1:12 solid-liquid ratio. The yields of essential oil and lignans are 12.12±0.37 ml/kg and 250.2±38.2 mg/kg under the optimum conditions. The composition of the essential oil extracted by hydro-distillation, steam-distillation and ILMAE is analyzed by GC-MS. With ILMAE method, the energy consumption time has not only been shortened to 40 min (hydro-distillation 3.0 h for extracting essential oil and reflux extraction 4.0 h for extracting lignans, respectively), but also the extraction efficiency has been improved (extraction of lignans and distillation of essential oil at the same time) and reduces the environmental pollution. S. chinensis materials treated by different methods are observed by scanning electronic microscopy. Micrographs provide more evidence to prove that ILMAE is a better and faster method. The experimental results also indicate that ILMAE is a simple and efficient technique for sample preparation.     

Qualitative and quantitative analysis of active flavonoids in Flos Lonicerae by capillary zone electrophoresis coupled with solid-phase extraction

Flavonoids are an important bioactive group in the commonly used herbal medicine Flos Lonicerae. A new method of capillary zone electrophoresis (CZE) coupled with solid-phase extraction (SPE) was developed for simultaneous assay of flavonoid aglycones and glycosides in Flos Lonicerae. Optimum CZE separation was achieved with a background electrolyte (BGE) solution consisting of 80 mM boric acid and 20 mM phosphate acid, adjusted to pH 8.1, with 15% acetonitrile (v/v) added, and applying a separation voltage of 28 kV. The SPE method was used for pretreating the complex matrix of botanical materials and good reproducibility was obtained when avicularin was used as internal standard. Linearity of the method was excellent with correlation coefficients (r2) in the range of 0.9995-0.9999 and detection limits were lower than 0.6 microg/mL for the four flavonoids. The obtained recoveries varied between 93 to 104% while the relative standard deviations (RSDs) were below 4.4% (n=3). The developed CZE method was successfully used for the separation of eight flavonoids and the quantification of the four flavonoids in five species of Flos Lonicerae.     

Determination of water soluble trace metals in airborne particulate matter using a dynamic extraction procedure with on-line inductively coupled plasma optical emission spectrometric detection

A novel continuous-flow system for the dynamic extraction of water soluble metal fractions in airborne particulate matter (APM) with subsequent inductively coupled plasma optical emission spectrometric (ICP-OES) analysis of derived extracts is presented. The fully automated extraction system with on-line multi-element detection offers enhanced sensitivity when compared to batch-wise counterparts; additionally it provides information about the extraction process. With the developed procedure detection limits in the order of 1.5 (Ba) to 8.0 (Ni) ng extractable mass per investigated sample could be achieved, which translates to method detection limits for soluble metal concentrations in APM ranging from 0.2 ng m⁻³ (Ba) to 0.9 ng m⁻³ (Fe). Reproducibility of analysis was determined by replicate measurement (n = 6) of an APM sample with an aerodynamic diameter ≤10 μm (PM10), derived results varied between 3.5% (Mn) and 12.1% (Ni) relative standard deviation. Method validation was accomplished by comparison of extracted soluble and remaining non-soluble fractions with the total metal contents of the investigated PM10 samples, showing an excellent mass balance for all elements. Application of the developed procedure for the analysis of water soluble metal fractions in PM10 samples (n = 16) from Linz (Austria) indicated a high variability of extractable fractions ranging from 11.7 ± 7.2% (Fe) to 48.8 ± 15.4% (Mn) of the total metal contents.     

Focused microwaves-assisted extraction and simultaneous spectrophotometric determination of vanillin and p-hydroxybenzaldehyde from vanilla fragans

A new method to quick extraction of vanillin and p-hydroxybenzaldheyde (PHB) of vanilla beans from vanilla fragans is proposed. Samples were irradiated with microwaves energy to accelerate the extraction process and photometric monitoring was performed at 348 and 329 nm (vanillin and PHB, respectively). The simultaneous determination of vanillin and PHB from extracts was performed using the Vierordt's method, which showed a precision, expressed as relative standard deviation, smaller 2.5% for both analytes. Conditions such as microwaves irradiation power, number of irradiation and non-irradiation cycles, irradiation time and ethanol concentration were optimized by means of multivariate screening that showed that irradiation power and number of irradiation cycles are the most significant condition in the vanilla extraction process. The focused microwave-assisted extraction (FMAE) was applied to commercial (dried vanilla beans from fresh green vanilla beans), lyophilised and dried (commercial vanilla dried at 135 °C in oven) vanilla beans samples. The results showed that the extraction of vanillin and PHB in the commercial vanilla samples were higher than in dried and lyophilised samples. With the proposed FMAE a decrease in the extraction time of 62 times and an increase in the vanillin and PHB concentrations between 40 and 50% with respect to the official Mexican extraction method, were obtained.     

Quantitative determination of chlorogenic acid in Honeysuckle using microwave-assisted extraction followed by nano-LC-ESI mass spectrometry

The chlorogenic acid (CA) in Honeysuckle is determined and identified by nano-liquid chromatography-electrospray ionization mass spectrometry (nano-LC-ESI/MS) after extraction with microwave-assisted extraction (MAE). As a new sample preparation method for Honeysuckle, the MAE procedure is optimized, validated and compared with conventional methods including reflux extraction (RE) and ultrasonic extraction (USE). It is found that MAE gives the best result due to the highest extraction efficiency within shortest extraction time (only 4 min). Here, CA is determined by nano-LC-ESI/MS based on the calibration curve of its authentic standard. The method linearity, detection limit, precision and recovery are studied. The results show that the combined MAE and nano-LC-ESI/MS method has a linearity (R² 0.991, 0.8-20 ng mL⁻¹), a low limit of detection (0.5 ng mL⁻¹), good precision (R.S.D. = 2.54%) and a recovery (84.8%). The experiment has demonstrated that the nano-LC-ESI/MS following MAE is a fast and reliable method for quantitative analysis of CA in Honeysuckle.