Column preconcentration of lead in aqueous solution with macroporous epoxy resin-based polymer monolithic matrix

The objective of this article was to investigate the feasibility of epoxy resin-based monoliths prepared by stepwise polymerization and column preconcentration of metal ions using large-scale monolithic matrix. A novel macroporous polymer monolith matrix was prepared from epoxy resin (EP) and ethylenediamine (EDA) and pore-forming reagent (polyethylene glycol, PEG-1000) by in situ step-addition polymerization. The morphology of the resulting polymer monolith was characterized by scanning electron microscopy (SEM). A solid-phase extraction (SPE) cartridge prepared from a simple glass-tube was used for the preconcentration and determination of Pb(II) combined with flame atomic absorption spectroscopy (FAAS). The characteristics of the monoliths for the extraction of Pb(II) in aqueous solution were investigated. The experimental results showed that trace Pb(II) ions could be quantitatively preconcentrated in the pH range of 4.0-9.0 with recoveries of >95%. The maximum static adsorption capacity of the monolith adsorbent was 106.8 mg g⁻¹. The column was eluted by 1.0 mol L⁻¹ HNO₃ and recovery of Pb(II) was more than 97%. Moreover, the polymer monolith adsorbent shows superior reusability and stability. The precision and the accuracy of the proposed procedure were satisfactory by analyzing a standard reference material and three natural water samples. It was shown that the EP-EDA monolith was suitable for the preconcentration of environmental Pb(II) as an ion-selective SPE adsorbent.     

Magnetic molecularly imprinted polymer beads prepared by microwave heating for selective enrichment of β-agonists in pork and pig liver samples

Novel magnetic molecularly imprinted polymer (MIP) beads using ractopamine as template for use in extraction was developed by microwave heating initiated suspension polymerization. Microwave heating, as an alternative heating source, significantly accelerate the polymerization process. By incorporating magnetic iron oxide, superparamagnetic composite MIP beads with average diameter of 80 μm were obtained. The imprinted beads were then characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis and vibrating sample magnetometer. Highly cross-linked porous surface and good magnetic property were observed. The adsorption isotherm modeling was performed by fitting the data to Freundlich isotherm model. The binding sites measured were 3.24 μmol g⁻¹ and 1.17 μmol g⁻¹ for the magnetic MIP beads and the corresponding non-imprinted magnetic beads, respectively. Cross-selectivity experiments showed the recognition ability of the magnetic MIP beads to analytes is relative to degree of molecular analogy to the template. Finally, this magnetic MIP bead was successfully used for enrichment of ractopamine, isoxsuprine and fenoterol from ultrasonically extracted solution of pork and pig liver followed by high performance chromatography with fluorescence detection. The proposed method presented good linearity and the detection limits was 0.52-1.04 ng mL⁻¹.The recoveries were from 82.0% to 90.0% and from 80.4% to 86.8% for the spiked pork and pig liver, respectively, with the RSDs of 5.8-10.0%. Combination of the specific adsorption property of the MIP material and the magnetic separation provided a powerful analytical tool of simplicity, flexibility, and selectivity.     

利用辅助识别聚合物链制备牛血清白蛋白分子印迹聚合物

论文提出了一种新的蛋白质分子印迹方法, 即以聚乙烯醇接枝聚合物作为辅助识别聚合物链(ARPCs), 以丙烯酰胺为单体, 在丙烯酸酯树脂载体表面进行聚合, 制备牛血清白蛋白分子印迹树脂. 实验使用2.00 mol•L⁻¹氯化钾(KC1)溶液除去模板蛋白质, 使用十二烷基磺酸钠-聚丙烯酰胺凝胶电泳(SDS-PAGE)检测吸附蛋白质, 并设计使用0.150, 0.500和2.00 mol•L⁻¹KC1溶液分别对吸附蛋白质进行梯度洗提. 电泳实验结果表明, 2.00 mol•L⁻¹KC1溶液洗脱的蛋白质是大孔树脂的吸附效应; 0.500 mol•L⁻¹KC1溶液洗脱掉的是印迹蛋白质. 引入ARPCs制得的分子印迹树脂, 用于混合蛋白质体系吸附时, 对模板蛋白质的吸附量为80~100μg•g⁻¹, 其特异性吸附能力较未引入ARPCs之前有明显提高.     

Sensitive and selective electrochemical determination of quinoxaline-2-carboxylic acid based on bilayer of novel poly(pyrrole) functional composite using one-step electro-polymerization and molecularly imprinted poly(o-phenylenediamine)

A facile and efficient molecularly imprinted polymer (MIP) recognition element of electrochemical sensor was fabricated by directly electro-polymerizing monomer o-phenylenediamine (oPD) in the presence of template quinoxaline-2-carboxylic acid (QCA), based on one-step controllable electrochemical modification of poly(pyrrole)-graphene oxide-binuclear phthalocyanine cobalt (II) sulphonate (PPY-GO-BiCoPc) functional composite on glassy carbon electrode (GCE). The MIP film coated on PPY-GO-BiCoPc functional composite decorated GCE (MIP/PPY-GO-BiCoPc/GCE) was presented for the first time. The synergistic effect and electro-catalytic activity toward QCA redox of PPY-GO-BiCoPc functional composite were discussed using various contrast tests. Also, the effect of experimental variables on the current response such as, electro-polymerization cycles, template/monomer ratio, elution condition for template removal, pH of the supporting electrolyte and accumulation time, were investigated in detail. Under the optimized conditions, the proposed MIP sensor possessed a fast rebinding dynamics and an excellent recognition capacity to QCA, while the anodic current response of square wave voltammetry (SWV) was well-proportional to the concentration of QCA in the range of 1.0 × 10⁻⁸–1.0 × 10⁻⁴ and 1.0 × 10⁻⁴–5.0 × 10⁻⁴ mol L⁻¹ with a low detection limit of 2.1 nmol L⁻¹. The established sensor was applied successfully to determine QCA in commercial pork and chicken muscle samples with acceptable recoveries (91.6–98.2%) and satisfactory precision (1.9–3.5% of SD), demonstrating a promising feature for applying the MIP sensor to the measurement of QCA in real samples.     

Preparation of a strong-cation exchange monolith by a novel method and its application in the separation of IgG on high performance liquid chromatography

A strong cation-exchange poly(vinyl carboxylate-co-ethyleneglycol dimethacrylate) (poly(VC-co-EDMA)) monolithic column for high performance liquid chromatography (HPLC) has been prepared firstly by atom transfer radical polymerization (ATRP) without the expensive complexing ligand, in which vinyl carboxylate was used as the monomer, ethyleneglycol dimethacrylate as the cross linking agent, carbon tetrachloride as the initiator and ferrous chloride as the catalyst. Conditions of the polymerization have been studied and optimized. Morphology of monolithic materials was studied by scanning electronic microscopy. Chemical groups of the monolith were assayed by infrared spectra method and the pore size distribution was determined by a mercury porosimeter. Moreover, the monolith was modified to bear strong-cation exchange groups and tested on the separation of human immune globulin G (IgG) from human plasma in conjunction with HPLC. Good resolution was obtained in a short time (10 min) in the separation. The effects of pH and buffer concentration on the elution of IgG have been investigated. Moreover, frontal analytical method was used to get the IgG dynamic banding capacity of the monolith that was 3.0 mg g⁻¹. Besides, the monolith was also used to separate lysozyme from egg white and separate the mixture of papain, snailase and IgG.     

Synthesis by precipitation polymerisation of molecularly imprinted polymer microspheres for the selective extraction of carbamazepine and oxcarbazepine from human urine

Two molecularly imprinted polymers (MIPs), in the physical form of well-defined polymer microspheres, were synthesised via precipitation polymerisation (PP) using an antiepileptic drug, carbamazepine (CBZ), as template molecule, methacrylic acid as functional monomer and either divinylbenzene 80 (DVB-80) or a mixture of DVB-80 and ethylene glycol dimethacrylate (EGDMA) as crosslinking agents. The MIP obtained using DVB-80 alone as crosslinking agent (MIP A) had a narrow particle size distribution (9.5 ± 0.5 μm) and a well-developed permanent pore structure (specific surface area in the dry state = 758 m² g⁻¹), whereas when a mixture of DVB-80 and EGDMA (MIP B) were used as crosslinking agents, the polymer obtained had a broader particle size distribution (6.4 ± 1.8 μm) and a relatively low specific surface area (23 m² g⁻¹). The molecular recognition character of both polymers was evaluated by means of LC and then a molecularly imprinted solid-phase extraction (MISPE) protocol; CBZ was recognised by both polymers, and useful cross-selectivity for oxcarbazepine (OCBZ), which is the main metabolite of CBZ, also observed. In a detailed bioanalytical study, MIP A was selected in preference to MIP B since MIP A enabled a high volume of sample to be extracted such that lower limits of detection were achievable using this polymer. High recoveries of CBZ and OCBZ were obtained in a MISPE protocol when 50 mL of human urine spiked at 0.2 mg L⁻¹ were percolated through MIP A (90% and 83%, respectively).     

Synthesis and application of a peroxidase-like molecularly imprinted polymer based on hemin for selective determination of serotonin in blood serum

This work reports the preparation of a molecularly imprinted polymer (MIP) for selective catalytic detection of serotonin (5-hydroxytryptamine, 5-HT). The process is based on the synthesis of polymers with hemin introduced as the catalytic center to mimic the active site of peroxidase. The copolymer MIP, containing artificial recognition sites for 5-HT, has been prepared by bulk polymerization using methacrylic acid (MAA) and hemin as the functional monomers, and ethylene glycol dimethacrylate (EGDMA) as the cross-linker. For the determination of 5-HT, a flow injection analysis system coupled to an amperometric detector was optimized using multivariate analysis. The effects of different parameters, such as pH, buffer flow rate, buffer nature, peroxide concentration and sample volume were evaluated. After optimizing the experimental conditions, a linear response range from 1.0 up to 1000.0 μmol L⁻¹ was obtained with a sensitivity of 0.4 nA/μmol L⁻¹. The detection limit was found to be 0.30 μmol L⁻¹, while the precision values (n = 6) evaluated by relative standard deviation (R.S.D.) were, respectively, 1.3 and 1.7% for solutions of 50 and 750 μmol L⁻¹ of 5-HT. No interference was observed by structurally similar compounds (including epinephrine, dopamine and norepinephrine), thus validating the good performance of the imprinted polymer. The method was applied for the determination of 5-HT in spiked blood serum samples.     

Molecularly imprinted polymer based potentiometric sensor for the determination of hydroxyzine in tablets and biological fluids

Molecular imprinting is a useful technique for the preparation of functional materials with molecular recognition properties. In this work, a biomimetic potentiometric sensor, based on a non-covalent imprinted polymer, was fabricated for the recognition and determination of hydroxyzine in tablets and biological fluids. The molecularly imprinted polymer (MIP) was synthesized by precipitation polymerization, using hydroxyzine dihydrochloride as a template molecule, methacrylic acid (MAA) as a functional monomer and ethylene glycol dimethacrylat (EGDMA) as a cross-linking agent. The sensor showed a high selectivity and a sensitive response to the template in aqueous system. The MIP-modified electrode exhibited a Nernstian response (29.4 ± 1.0 mV decade⁻¹) in a wide concentration range of 1.0 × 10⁻⁶ to 1.0 × 10⁻¹ M with a lower detection limit of 7.0 × 10⁻⁷ M. The electrode demonstrated a response time of ∼15 s, a high performance and a satisfactory long-term stability (more than 5 months). The method has the requisite accuracy, sensitivity and precision to assay hydroxyzine in tablets and biological fluids.     

Carbon monolith: Preparation,characterization and application as microextraction fiber

A carbon monolith was synthesized via a polymerization–carbonization method, styrene and divinylbenzene being adopted as precursors and dodecanol as a porogen during polymerization. The resultant monolith had bimodal porous substructure, narrowly distributed nano skeleton pores and uniform textural pores or throughpores. The carbon monolith was directly used as an extracting fiber, taking place of the coated silica fibers in commercially available solid-phase microextraction device, for the extraction of phenols followed by gas chromatography–mass spectrometry. Under the studied conditions, the calibration curves were linear from 0.5 to 50 ng mL⁻¹ for phenol, o-nitrophenol, 2,4-dichlorophenol and p-chlorophenol. The limits of detection were between 0.04 and 0.43 ng mL⁻¹. The recoveries of the phenols spiked in real water samples at 10 ng mL⁻¹ were between 85% and 98% with the relative standard deviations below 10%. Compared with the commercial coated ones (e.g. PDMS, CW/DVB and DVB/CAR/PDMS), the carbon monolith-based fiber had advantages of faster extraction equilibrium and higher extraction capacity due to the superior pore connectivity and pore openness resulting from its bimodal porous substructure.     

A novel high selective and sensitive para-nitrophenol voltammetric sensor, based on a molecularly imprinted polymer-carbon paste electrode

By using a molecularly imprinted polymer (MIP) as a recognition element, the design and construction of a high selective voltammetric sensor for para-nitrophenol was formed. Para-nitrophenol selective MIP and a non-imprinted polymer (NIP) were synthesized, and then used for carbon paste (CP) electrode preparation. The MIP-CP electrode showed greater recognition ability in comparison to the NIP-CP. It was shown that electrode washing after para-nitrophenol extraction led to enhanced selectivity, without noticeably decreasing the sensitivity. Some parameters affecting sensor response were optimized and a calibration curve was plotted. A dynamic linear range of 8 × 10⁻⁹ to 5 × 10⁻⁶ mol L⁻¹ was obtained. The detection limit of the sensor was calculated as 3 × 10⁻⁹ mol L⁻¹. Thus, this sensor was used successfully for the para-nitrophenol determination in different water samples.     

Preparation and evaluation of a macroporous molecularly imprinted hybrid silica monolithic column for recognition of proteins by high performance liquid chromatography

A novel type of macroporous molecularly imprinted hybrid silica monolithic column was first developed for recognition of proteins. The macroporous silica-based monolithic skeleton was synthesized in a 4.6 mm i.d. stainless steel column by a mild sol–gel process with methyltrimethoxysilane (MTMS) as a sole precursor, and then vinyl groups were introduced onto the surface of the silica skeleton by chemical modification of γ-methacryloxypropyltrimethoxysilane (γ-MAPS). Subsequently, the molecularly imprinted polymer (MIP) coating was copolymerized and anchored onto the surface of the silica monolith. Bovine serum albumin (BSA) and lysozyme (Lyz), which differ greatly in molecular size, isoelectric point, and charge, were representatively selected for imprinted templates to evaluate recognition property of the hybrid silica-based MIP monolith. Some important factors, such as template–monomer molar ratio, total monomer concentration and crosslinking density, were systematically investigated. Under the optimum conditions, the obtained hybrid silica-based MIP monolith showed higher binding affinity for template than its corresponding non-imprinted (NIP) monolith. The imprinted factor (IF) for BSA and Lyz reached 9.07 and 6.52, respectively. Moreover, the hybrid silica-based MIP monolith displayed favorable binding characteristics for template over competitive protein. Compared with the imprinted silica beads for stationary phase and in situ organic polymer-based hydrogel MIP monolith, the hybrid silica MIP monolith exhibited higher recognition, stability and lifetime.     

An optical sensor for the determination of digoxin in serum samples based on a molecularly imprinted polymer membrane

This paper reports the synthesis and testing of a molecularly imprinted polymer membrane for digoxin analysis. Digoxin-specific bulk polymer was obtained by the UV initiated co-polymerisation of methacrylic acid and ethylene glycol dimethacrylate in acetonitrile as porogen. After extracting the template analyte, the ground polymer particles were mixed with plasticizer polyvinyl chloride to form a MIP membrane. A reference polymer membrane was prepared from the same mixture of monomers but with no template. The resultant membrane morphologies were examined by scanning electron microscopy. The imprinted membrane was tested as the recognition element in a digoxin-sensitive fluorescence sensor; sensor response was measured using standard solutions of digoxin at concentrations of up to 4 × 10⁻³ mg L⁻¹. The detection limit was 3.17 × 10⁻⁵ mg L⁻¹. Within- and between-day relative standard deviations RSD (n = 5) were in the range 4.5-5.5% and 5.5-6.5% respectively for 0 and 1 × 10⁻³ mg L⁻¹ digoxin concentrations. A selectivity study showed that compounds of similar structure to digoxin did not significantly interfere with detection for interferent concentrations at 10, 30 and 100 times higher than the digoxin concentration. This simply manufactured MIP membrane showed good recognition characteristics, a high affinity for digoxin, and provided satisfactory results in analyses of this analyte in human serum.     

Chromatographic characterisation, under highly aqueous conditions, of a molecularly imprinted polymer binding the herbicide 2,4-dichlorophenoxyacetic acid

The affinity of a 2,4-dichlorophenoxyacetic acid (2,4-D) molecularly imprinted polymer (MIP), which was synthesised directly in an aqueous organic solvent, for its template (2,4-D) was studied and compared with the affinity exhibited by two other reference (control) polymers, NIPA and NIPB, for the same analyte. Zonal chromatography was performed to establish the optimal selectivity, expressed as imprinting factor (IF), under chromatographic conditions more aqueous than those described so far in the literature. Frontal analysis (FA) was performed on columns packed with these polymers, using an optimized mobile phase composed of methanol/phosphate buffer (50/50, v/v), to extract adsorption isotherm data and retrieve binding parameters from the best isotherm model. Surprisingly, the template had comparable and strong affinity for both MIP (K = 3.8 × 10⁴ M⁻¹) and NIPA (K = 1.9 × 10⁴ M⁻¹), although there was a marked difference in the saturation capacities of selective and non-selective sites, as one would expect for an imprinted polymer. NIPB acts as a true control polymer in the sense that it has relatively low affinity for the template (K = 8.0 × 10² M⁻¹). This work provides the first frontal chromatographic characterization of such a polymer in a water-rich environment over a wide concentration range. The significance of this work stems from the fact that the chromatographic approach used is generic and can be applied readily to other analytes, but also because there is an increasing demand for well-characterised imprinted materials that function effectively in aqueous media and are thus well-suited for analytical science applications involving, for example, biofluids and environmental water samples.     

A highly selective molecularly imprinted electrochemiluminescence sensor for ultra-trace beryllium detection

A new molecularly imprinted electrochemiluminescence (ECL) sensor was proposed for highly sensitive and selective determination of ultratrace Be²⁺ determination. The complex of Be²⁺ with 4-(2-pyridylazo)-resorcinol (PAR) was chosen as the template molecule for the molecularly imprinted polymer (MIP). In this assay, the complex molecule could be eluted from the MIP, and the cavities formed could then selectively recognize the complex molecules. The cavities formed could also work as the tunnel for the transfer of probe molecules to produce sound responsive signal. The determination was based on the intensity of the signal, which was proportional to the concentrations of the complex molecule in the sample solution, and the Be²⁺ concentration could then be determined indirectly. The results showed that in the range of 7 × 10⁻¹¹ mol L⁻¹ to 8.0 × 10⁻⁹ mol L⁻¹, the ECL intensity had a linear relationship with the Be²⁺ concentrations, with the limit of detection of 2.35 × 10⁻¹¹ mol L⁻¹. This method was successfully used to detect Be²⁺ in real water samples.     

Directly light scattering imaging of the aggregations of biopolymer bound chromium(III) hydrolytic oligomers in aqueous phase and liquid/liquid interface

Investigations of inorganic oligomers are important in both chemistry and physiology. In this contribution, we propose a laser induced light scattering imaging (LSI) and a total internal reflected light scattering imaging (TIR-LSI) technique, and apply them to characterize the interactions of inorganic oligomers with biopolymer in aqueous phase and at liquid/liquid interface, respectively. In aqueous medium, synthetic chromium(III) hydrolytic oligomers (CrHO) react with DNA, and the resultant binary could be extracted into the H₂O/CCl₄ interface in the presence of triocyctyl phosphine oxide (TOPO), forming a DNA-CrHO-TOPO ternary amphipathic complex at the interface with the associate constant of 1.32 × 10³ mol⁻¹ dm⁴ for a given 1.0 × 10⁻⁴ mol l⁻¹ TOPO. Under the excitation of a 441-nm He-Cd laser light beam, the resultant light scattering and total internal reflected light scattering (TIR-LS) signals of the formed binary in aqueous phase and ternary at liquid/liquid interface could be easily captured using a common microscope coupled with a CCD camera. By digitally analyzing the CCD captures, we demonstrate that aggregations of the CrHO-DNA binary in aqueous phase and DNA-CrHO-TOPO ternary at liquid/liquid interface have occurred, respectively.     

A microflow chemiluminescence system for determination of chloramphenicol in honey with preconcentration using a molecularly imprinted polymer

A novel chemiluminescence (CL) microfluidic system incorporating a molecularly imprinted polymer (MIP) preconcentration step was used for the determination of chloramphenicol in honey samples. The MIP was prepared by using chloramphenicol as the template, diethylaminoethyl methacrylate (DAM) as the function monomer, ethylene glycol dimethacrylate (EGDMA) as the cross-linking monomer, 2, 2′-dimethoxy-2-phenylacetophenone (DMPA) as the free radical initiator and toluene and dodecanol as the solvent. The MIP was pre-loaded into a 10 mm long, 2 mm wide and 150 μm deep channel in a planar glass microfluidic device. When the sample containing chloramphenicol was introduced into the microfluidic device it was first preconcentrated on the MIP then detected by an enhancement effect on the chemiluminescence reaction of tris(2, 2′-bipyridyl) ruthenium(II) with cerium(IV) sulphate in sulphuric acid. A micro-syringe pump was used to pump the reagents. The CL intensity was linear in relationship to the chloramphenicol concentrations from 1.55 × 10⁻⁴ to 3.09 × 10⁻³ μmol L⁻¹ (r² = 0.9915) and the detection limit (3σ) and the quantitation limit (10σ) were found to be 7.46 × 10⁻⁶ and 2.48 × 10⁻⁵ μmol L⁻¹, respectively. This method offered a high selectivity and sensitivity for quantitative analysis of chloramphenicol in the honey samples.     

Albumin molecularly imprinted polymer with high template affinity — Prepared by systematic optimization in mixed organic/aqueous media

An approach using systematic optimization for the formation of an albumin molecularly imprinted polymer (MIP), able to separate albumin from proteins in solution, has been prepared by imprinting albumin using a copolymer comprising 3-dimethylaminopropyl methacrylate and tetraethylene glycol dimethacrylate in a mole ratio of 1 to 8. Cytochrome c, lysozyme and myoglobin were used in competitive re-binding experiments to compete with the polymer's native template with all protein species present at 0.0004 g mL^− 1. The effects of: monomer to crosslinker mole ratio, polymerization temperature and time were investigated. It was found that the addition of water 6.04%, into the pre-polymerization albumin-monomer complex enhanced the adsorption capacity and selectivity of the resulting MIP from 2.18 × 10^− 3 to 6.02 × 10^− 3 g g-MIP^− 1 and 83.5% to 98.7%, respectively. These results also showed that the MIP possessed high selectivity and adsorption capacity with respect to albumin in comparison with interfering species also present in solution. Polymerization temperature, time and the water content of the pre-polymerization mixture were all shown to have significant effects on the resulting albumin-MIP's performance. However, their influence on the polymer's affinity for the potentially interfering species was negligible. Additionally, higher polymerization temperatures (> 38 °C) and extended polymerization times (> 60 h) increased monomer conversion as determined by HPLC, but decreased the selectivity and adsorption capacity of the MIP. An optimized MIP, with very high selectivity and 6.37 × 10^− 3 g g-MIP^− 1 template re-adsorption capacity was obtained using the following polymerization conditions: 0.125 mole ratio of monomer to crosslinker, 6.04 wt.% water content with respect to the mass of the monomer complex, 60 h polymerization time at 38 °C, and with 0.47% albumin in the pre-polymerization monomer complex. Finally, the functions of polymerization temperature, time and the significance of the water content in the albumin-monomer complex are also discussed.     

Preparation and characterization of grafted imprinted monolith for capillary electrochromatography

In this paper, a molecularly imprinted polymer (MIP) coating grafted to a trimethylolpropane trimethacrylate (TRIM) core material for CEC was reported. The core monolith was prepared with a solution of 20% (w/w) TRIM in a mixture of porogen and a polymerization precursor, which can generate a stable electroosmotic flow due to the formation of ionizable groups after postpolymerization hydrolization. Graft polymerization took place on the resultant TRIM monolith with a mixture of template, methacrylic acid, and ethylene glycol dimethacrylate. Strong recognition ability (selectivity factor was 5.83) for S‐amlodipine and resolution of enatiomers separation (up to 7.99) were obtained on the resulting grafted imprinted monolith in CEC mode. The influence of CEC conditions on chiral separation, including the composition of mobile phase, pH value, and the operating voltages was studied. These results suggest that the method of grafted polymerization reported here allows a rapid development of MIP monolith once core materials with desired properties are available, and is a good alternative to prepare CEC‐based monolithic MIPs.     

Determination of molybdenum in environmental samples

Molecular imprinted membrane of indole-3-ethanol (IE) was prepared by hybridization of IE imprinted polymer powder and polysulfone (PSf) membrane. The IE imprinted polymer by covalent imprinting method was synthesized with copolymerization of indole-3-ethyl methacrylate (IEMA) and divinylbenzene (DVB). The cross-linked P(IEMA-co-DVB) was ground to be powders having less than 63 μm size and then hybridized within PSf membrane by using phase inversion process. The resultant imprinted powder showed binding capacities of 1.8, 7.2, 0 and 0 μmol g⁻¹ for IE, indole, 8-hydroxyquinoline and pyrrole in aqueous solution, respectively, and after hybridization with the PSf membrane, the value was 46, 26, 0 and 0 μmol g⁻¹. As a result, it was found that the IE imprinted powder alone showed non-selectively binding to the IE, but, the hybridized powder within the PSf membrane bound selectively the IE. Evidence was presented that hydrophobic interaction of the PSf matrix caused the selective and efficient binding. We also showed separation behavior of the hybrid membranes and discussed on the binding selectivity of the IE molecule. In view point of hybrid effect of the PSf membrane and the cross-linked imprinted powder, the results of the separation of these substrates were considered.     

Development of a new high performance low pressure chromatographic system using a multisyringe burette coupled to a chromatographic monolithic column

A novel combination of high performance low pressure chromatography with multisyringe flow injection analysis is presented. This system comprises a multisyringe module, three low pressure solenoid valves, a monolithic Chromolith Flash RP-18e column and a diode array spectrophotometer. UV detection is carried out at 250 nm. AutoAnalysis software is used for instrumental control and automated data collection. The results obtained with multisyringe liquid chromatography (MSC) were compared with those obtained with a HPLC system using similar conditions. The chromatographic parameters were calculated from a mixture of anthracene and thiourea using a mobile phase containing acetonitrile-water (60:40) at a flow rate of 2 ml min⁻¹. The proposed MSC system has been successfully applied to the determination of amoxicillin, ampicillin and cephalexin using a mobile phase of sodium acetate buffer (pH 6.2, 0.1 mol l⁻¹)-methanol (90:10) at a flow rate of 2 ml min⁻¹. The low-cost, flexibility and simplicity of MSC should be highlighted.