Effect of dimensions of multi-walled carbon nanotubes on its enrichment efficiency of metal ions from environmental waters

The effect of dimensions (length and external diameter) of multi-walled carbon nanotubes (MWCNTs) on its preconcentration efficiency towards some metal ions (Pb²⁺, Cd²⁺, Cu²⁺, Zn²⁺ and MnO₄⁻) from environmental waters prior to their analysis by flame atomic absorption spectroscopy (FAAS) was investigated. MWCNTs (as-received from the manufacturer) of various external diameters and lengths were involved. Other variables optimized included effects of pH of water sample, composition and volume of eluent, mass of the MWCNTs, breakthrough volume and coexisting ions. Maximum recovery of metal ions was obtained at pH 9 where it was thought that precipitation of metals as their hydroxides played the major factor in metals uptake by MWCNT. It was suggested that the use of appropriate dimensions of MWCNTs may support the trapping process of the precipitated metal hydroxides by MWCNTs. It was found that long MWCNT of length 5-15 μm and external diameter 10-30 nm gave the highest enrichment efficiency towards almost all the targeted metal ions. It could be used for preconcentration of MnO₄⁻, Cu²⁺, Zn²⁺ and Pb²⁺ with almost full recovery; but not for Cd²⁺ due to its low recovery. The optimized solid phase extraction (SPE) procedure was capable of determining metal ions in the linear range 20-100 ng mL⁻¹ (except for Zn²⁺ from 20 to 150 ng mL⁻¹). Detection limits were 0.709 ng mL⁻¹ for MnO₄⁻, 0.278 ng mL⁻¹ for Pb²⁺, 0.465 ng mL⁻¹ for Cu²⁺, 0.867 ng mL⁻¹ for Zn²⁺. Application of the optimized SPE procedure to environmental waters (tap water, reservoir water and stream water) gave spike recoveries of the metals in the range of 81-100%.     

Ultra-sensitive determination of cyanide in surface water by gas chromatography–tandem mass spectrometry after derivatization with 2-(dimethylamino)ethanethiol

A gas chromatography–tandem mass spectrometric (GC–MS/MS) method has been established for the determination of cyanide in surface water. This method is based on the derivatization of cyanide with 2-(dimethylamino)ethanethiol in surface water. The following optimum reaction conditions were established: reagent dosage, 0.7 g L⁻¹ of 2-(dimethylamino)ethanethiol; pH 6; reaction carried out for 20 min at 60 °C. The organic derivative was extracted with 3 mL of ethyl acetate, and then measured by using GC–MS/MS. Under the established conditions, the detection and quantification limits were 0.02 μg L⁻¹ and 0.07 μg L⁻¹ in 10-mL of surface water, respectively. The calibration curve had a linear relationship relationship with y = 0.7140x + 0.1997 and r² = 0.9963 (for a working range of 0.07–10 μg L⁻¹) and the accuracy was in a range of 98–102%; the precision of the assay was less than 7% in surface water. The common ions Cl⁻, F⁻, Br⁻, NO₃⁻, SO₄²⁻, PO₄³⁻, K⁺, Na⁺, NH₄⁺, Ca²⁺, Mg²⁺, Ba²⁺, Mn⁴⁺, Mn²⁺, Fe³⁺, Fe²⁺ and sea water did not interfere in cyanide detection, even when present in 1000-fold excess over the species. Cyanide was detected in a concentration range of 0.07–0.11 μg L⁻¹ in 6 of 10 surface water samples.     

Microvolume turbidimetry for rapid and sensitive determination of the acid labile sulfide fraction in waters after headspace single-drop microextraction with in situ generation of volatile hydrogen sulfide

In this work, we demonstrate the feasibility of applying headspace single-drop microextraction with in-drop precipitation for the quantitative determination of the acid labile sulfide fraction (H₂S, HS⁻, and S²⁻ (free sulfide), amorphous FeS and some metal sulfide complexes-clusters as ZnS) in aqueous samples by microvolume turbidimetry. The methodology lies in the in situ hydrogen sulfide generation and subsequent sequestration into an alkaline microdrop containing ZnO₂²⁻ and exposed to the headspace above the stirred aqueous sample. The ZnS formed in the drop was then determined by microvolume turbidimetry. The optimum experimental conditions of the proposed method were: 2 μL of a microdrop containing 750 mg L⁻¹ Zn(II) in 1 mol L⁻¹ NaOH exposed to the headspace of a 20-mL aqueous sample stirred at 1600 rpm during 80 s after derivatization with 1 mL of 6 mol L⁻¹ HCl. An enrichment factor of 1710 was achieved in only 80 s. The calibration graph was linear in the range of 5-100 μg L⁻¹ with a detection limit of 0.5 μg L⁻¹. The repeatability, expressed as relative standard deviation, was 5.8% (N = 9). Finally, the proposed methodology was successfully applied to the determination of the acid labile sulfide fraction in different natural water samples.     

Determination of Hg on poly(vinylferrocenium) (PVF)-modified platinum electrode

A new surface based on poly(vinylferrocenium) (PVF⁺)-modified platinum electrode was developed for determination of Hg²⁺ ions in aqueous solutions. The polymer was electrodeposited on platinum electrode by constant potential electrolysis as PVF⁺ClO₄⁻. Cl⁻ ions were then attached to the polymer matrix by anion exchange and the modified electrode was dipped into Hg²⁺ solution. Hg²⁺ was preconcentrated at the polymer matrix by adsorption and also complexation reaction with Cl⁻. Detection of Hg²⁺ was carried out by differential pulse anodic stripping voltammetry (DPASV) after reduction of Hg²⁺. Mercury ions as low as 5 × 10⁻¹⁰ M could be detected with the prepared electrode and the relative standard deviation was calculated as 6.35% at 1 × 10⁻⁶ M concentration (n = 6). Interferences of Ag⁺, Pb²⁺ and Fe³⁺ ions were also studied at two different concentration ratios with respect to Hg²⁺. The developed electrode was applied to the determination of Hg²⁺ in water samples.     

Highly selective and sensitive paper-based colorimetric sensor using thiosulfate catalytic etching of silver nanoplates for trace determination of copper ions

A novel, highly selective and sensitive paper-based colorimetric sensor for trace determination of copper (Cu²⁺) ions was developed. The measurement is based on the catalytic etching of silver nanoplates (AgNPls) by thiosulfate (S₂O₃²⁻). Upon the addition of Cu²⁺ to the ammonium buffer at pH 11, the absorption peak intensity of AuNPls/S₂O₃²⁻ at 522 nm decreased and the pinkish violet AuNPls became clear in color as visible to the naked eye. This assay provides highly sensitive and selective detection of Cu²⁺ over other metal ions (K⁺, Cr³⁺, Cd²⁺, Zn²⁺, As³⁺, Mn²⁺, Co²⁺, Pb²⁺, Al³⁺, Ni²⁺, Fe³⁺, Mg²⁺, Hg²⁺ and Bi³⁺). A paper-based colorimetric sensor was then developed for the simple and rapid determination of Cu²⁺ using the catalytic etching of AgNPls. Under optimized conditions, the modified AgNPls coated at the test zone of the devices immediately changes in color in the presence of Cu²⁺. The limit of detection (LOD) was found to be 1.0 ng mL⁻¹ by visual detection. For semi-quantitative measurement with image processing, the method detected Cu²⁺ in the range of 0.5–200 ng mL⁻¹(R² = 0.9974) with an LOD of 0.3 ng mL⁻¹. The proposed method was successfully applied to detect Cu²⁺ in the wide range of real samples including water, food, and blood. The results were in good agreement according to a paired t-test with results from inductively coupled plasma-optical emission spectrometry (ICP-OES).     

Microflow injection chemiluminescence system with spiral microchannel for the determination of cisplatin in human serum

A new microflow injection chemiluminescence (μFI-CL) system was described for the determination of cisplatin in human serum. By using the microchip with double spiral channel configuration, the sensitivity was greatly enhanced due to more efficient mixing of the analyte and reagent solutions. Experimental results revealed that common ions in human serum, such as Mn²⁺, Co²⁺, Fe³⁺, Cu²⁺, Zn²⁺, Ni²⁺, Na⁺, K⁺, Ca²⁺, Cl⁻, NO₃⁻, Ac⁻, CO₃²⁻, PO₄³⁻, SO₄²⁻ did not cause interference with the detection of Pt(II) by using 1,10-phenanthroline as the masking agent. Under the optimized conditions, a linear calibration curve (R² = 0.998) over the range 2.0 × 10⁻⁸ to 2.0 × 10⁻⁶ mol L⁻¹ was obtained with the detection limit of 1.24 × 10⁻⁹ mol L⁻¹. The relative standard deviation was found to be 3.46% (n = 12) for 2.0 × 10⁻⁷ mol L⁻¹. The sample consumption was only 2 μL with the sample throughput of 72 h⁻¹. It had been used for trace platinum determination in cisplatin injection and human serum samples after the dosage of cisplatin. The recovery varied from 97.6 to 103.9%. The results proved that the proposed μFI-CL system had the advantages of high sensitivity and precision, low sample and reagents consumption, and high analytical throughput.     

Direct spectrophotometric determination of calcium in clinical samples with carboxyazo-p-CH3

A highly sensitive and relatively interference-free spectrophotometric method for determination of calcium is described. The method is based on the reaction between calcium ions and carboxyazo-p-CH₃ in aqueous citrate medium of pH 7, to form a blue complex with maximum absorption at 716 nm. The calibration is linear up to 0.12 μg ml⁻¹ calcium with a repeatability (R.S.D.) of 1.0% at a concentration of 0.04 μg ml⁻¹ (n=5). The molar absorptivity of the complex and Sandell’s sensitivity are 3.5×10⁵ l mol⁻¹ cm⁻¹ and 0.11 ng cm⁻², its 10σ limit of quantification and the 3σ limit of detection were found to be 0.3 ng ml⁻¹ and 0.09 ng ml⁻¹ respectively. The influence of reaction variables and the effect of interfering ions are studied; no interference was observed in clinical samples. The proposed method has been applied directly to the determination of calcium in clinical samples without the need for pre-concentration, masking metal ions and digesting samples.     

A new BOD estimation method employing a double-mediator system by ferricyanide and menadione using the eukaryote Saccharomyces cerevisiae

A new biochemical oxygen demand (BOD) sensing method employing a double-mediator (DM) system coupled with ferricyanide and a lipophilic mediator, menadione and the eukaryote Saccharomyces cerevisiae has been developed. In this study, a stirred micro-batch-type microbial sensor with a 560 μL volume and a two-electrode system was used. The chronamperometric response of this sensor had a linear response between 1 μM and 10 mM hexacyanoferrate(II) (r² = 0.9995, 14 points, n = 3, average of relative standard deviation and R.S.D._av = 1.3%). Next, the optimum conditions for BOD estimation by the DM system (BOD_DM) were investigated and the findings revealed that the concentration of ethanol, used to dissolve menadione, influenced the sensor response and a relationship between the sensor output and glucose glutamic acid concentration was obtained over a range of 6.6-220 mg O₂ L⁻¹ (five points, n = 3, R.S.D._av 6.6%) when using a reaction mixture incubated for 15 min. Subsequently, the characterization of this sensor was studied. The sensor responses to 14 pure organic substances were compared with the conventional BOD₅ method and other biosensor methods. Similar results with the BOD biosensor system using Trichosporon cutaneum were obtained. In addition, the influence of chloride ion, artificial seawater and heavy metal ions on the sensor response was investigated. A slight influence of 20.0 g L⁻¹ chloride ion and artificial seawater (18.4 g L⁻¹ Cl⁻) was observed. Thus, the possibility of BOD determination for seawater was suggested in this study. In addition, no influence of the heavy metal ions (1.0 mg L⁻¹ Fe³⁺, Cu²⁺, Mn²⁺, Cr³⁺ and Zn²⁺) was observed. Real sample measurements using both river water and seawater were performed and compared with those obtained from the BOD₅ method. Finally, stable responses were obtained for 14 days when the yeast suspension was stored at 4 °C (response reduction, 93%; R.S.D. for 6 testing days, 9.1%).     

Novel coated-graphite membrane sensor based on N,N′-dimethylcyanodiaza-18-crown-6 for the determination of ultra-trace amounts of lead

A novel selective membrane electrode for determination of ultra-trace amount of lead was prepared. The PVC membrane containing N,N′-dimethylcyanodiaza-18-cown-6 (DMCDA18C6) directly coated on a graphite electrode, exhibits a Nernstian response for Pb²⁺ ions over a very wide concentration range (from 1.0×10⁻² to 1.0×10⁻⁷ M) with a limit of detection of 7.0×10⁻⁸ M (∼14.5 ppb). It has a fast response time of ∼10 s and can be used for at least 2 months without any major deviation in potential. The electrode revealed very good selectivity with respect to all common alkali, alkaline earth, transition and heavy metal ions. The proposed sensor was used as an indicator electrode in potentiometric titration of lead ions and in determination of lead in edible oil, human hair and water samples. The proposed sensor was found to be superior to the best Pb²⁺-selective electrodes reported in terms of detection limit and selectivity coefficient.     

Sensitive and robotic determination of bromate in sea water and drinking deep-sea water by headspace solid-phase micro extraction and gas chromatography–mass spectrometry

A robotic method has been established for the determination of bromate in sea water and drinking deep-sea water. Bromate in water was converted into volatile derivative, which was measured with headspace solid-phase micro extraction and gas chromatography–mass spectrometry (HS-SPME GC–MS). Derivatization reagent and the HS-SPME parameters (selection of fibre, extraction/derivatization temperature, heating time and; the morality of HCl) were optimized and selected. Under the established conditions, the detection and the quantification limits were 0.016 μg L⁻¹ and 0.051 μg L⁻¹, respectively, and the intra- and inter-day relative standard deviation was less than 7% at concentrations of 1.0 and 10.0 μg L⁻¹. The calibration curve showed good linearity with r² = 0.9998. The common ions Cl⁻, NO₃⁻, SO₄²⁻, HPO₄²⁻, H₂PO₄⁻, K⁺, Na⁺, NH₄⁺, Ca²⁺, Mg²⁺, Ba²⁺, Mn⁴⁺, Mn²⁺, Fe³⁺ and Fe²⁺ did not interfere even when present in 1000-fold excess over the active species. The method was successfully applied to the determination of bromate in sea water and drinking deep-sea water.     

Flow injection fluorimetric determination of chromium(VI) in electroplating baths by luminescence quenching of tris(2,2'-bipyridyl) ruthenium(II)

A sensitive and selective luminescence quenching method is developed and used for manual and flow injection analysis (FIA) of chromium(VI) by reaction with [Ru(bpy)₃]²⁺. The emission peak of ruthenium(II) at 595 nm is linearly decreased as a function of Cr(VI) concentration. This permits determination of chromium(VI) ion over the concentration range 0.1-20 μg ml⁻¹ with a detection limit of 33 ng ml⁻¹. The quenching process is due to an electron transfer from the luminescent [Ru(bpy)₃]²⁺ complex ion to Cr(VI) resulting in the formation of the non-luminescent [Ru(bpy)₃]³⁺ complex ion. Selectivity for Cr(VI) over many anions and transition, alkali and alkaline earth metal cations is demonstrated. High concentration levels of sulphate, chloride, borate, acetate, phosphate, nitrate, cyanide, Pb²⁺, Zn²⁺, Hg²⁺, Cu²⁺, Cd²⁺, Ni²⁺ and Mn²⁺ ions are tolerated. The effects of solution pH and [Ru(bpy)₃]²⁺ reagent concentration are examined and the reaction conditions are optimized. Validation of the method according to the quality assurance standards show suitability of the proposed method for use in the quality control assessment of Cr(VI) in complex matrices without prior treatment. The method is successfully applied to determine chromium(VI) in electroplating baths using flow injection analysis. Results with a mean standard deviation of ±0.6% are obtained which compare fairly well with data obtained using atomic absorption spectrometry.     

Multiplex sensor for detection of different metal ions based on on–off of fluorescent gold nanoclusters

In this study, a multiplex fluorescence sensor for successive detection of Fe³⁺, Cu²⁺ and Hg²⁺ ions based on “on–off” of fluorescence of a single type of gold nanoclusters (Au NCs) is described. Any of the Fe³⁺, Cu²⁺ and Hg²⁺ ions can cause quenching fluorescence of Au NCs, which established a sensitive sensor for detection of these ions respectively. With the introduction of ethylene diamine tetraacetic acid (EDTA) to the system of Au NCs and metal ions, a restoration of fluorescence may be found with the exception of Hg²⁺. A highly selective detection of Hg²⁺ ion is, thus, achieved by masking Fe³⁺ and Cu²⁺. On the other hand, the masking of Fe³⁺ and Cu²⁺ leads to the enhancement of fluorescence of Au NCs, which in turn provides an approach for successive determination of Fe³⁺ and Cu²⁺ based on “on–off” of fluorescence of Au NCs. Moreover, this assay was applied to the successful detection of Fe³⁺, Cu²⁺ and Hg²⁺ in fish, a good linear relationship was found between these metal ions and the degree of quenched fluorescent intensity. The dynamic ranges of Hg²⁺, Fe³⁺ and Cu²⁺ were 1.96 × 10⁻¹⁰–1.01 × 10⁻⁹, 1.28 × 10⁻⁷–1.27 × 10⁻⁶ and 1.2 × 10⁻⁷–1.2 × 10⁻⁶ M with high sensitivity (the limit of detection of Fe³⁺ 2.0 × 10⁻⁸ M, Cu²⁺ 1.9 × 10⁻⁸ M and Hg²⁺ 2 × 10⁻¹⁰ M). These results indicate that the assay is suitable for sensitive detection of these metal ions even under the coexistence, which can not only determine all three kinds of metal ions successively but also of detecting any or several kinds of metal ions.     

Pre-evaluation of metal ions as a catalyst on chemiluminometric sequential injection analysis with luminol-H2O2 system

Catalytic effect of metal ions on luminol chemiluminescence (CL) was investigated by sequential injection analysis (SIA). The SIA system was set up with two solenoid micropumps, an eight-port selection valve, and a photosensor module with a fountain-type chemiluminescence cell. The SIA system was controlled and the CL signals were collected by a LabVIEW program. Aqueous solutions of luminol, H₂O₂, and a sample solution containing metal ion were sequentially aspirated to the holding coil, and the zones were immediately propelled to the detection cell. After optimizing the parameters using 1 × 10⁻⁵ M Fe³⁺ solution, catalytic effect of some metal species was compared. Among 16 metal species examined, relatively strong CL responses were obtained with Fe³⁺, Fe²⁺, VO²⁺, VO₃⁻, MnO₄⁻, Co²⁺, and Cu²⁺. The limits of detection by the present SIA system were comparable to FIA systems. Permanganate ion showed the highest CL sensitivity among the metal species examined; the calibration graph for MnO₄⁻ was linear at the concentration level of 10⁻⁸ M and the limit of detection for MnO₄⁻ was 4.0 × 10⁻¹⁰ M (S/N = 3).     

Development of a fluorescent chelating ligand for gallium ion having a quinazoline structure with two Schiff base moieties

A novel chelating ligand, 2,4-[bis-(2,4-dihydroxybenzylidene)]-dihydrazinoquinazoline (DBHQ), was synthesized, and the fluorescence characteristics of its complex with metal ions were investigated.Thirty-five different metal ions were tested for the emission of fluorescence in the presence of DBHQ in aqueous solutions in a pH range of 3.0-10.5 (at a difference of 0.5 for each metal).It was observed that DBHQ fluoresces intensely at 470 nm with an excitation wavelength of 405 nm in the presence of Ga³⁺ or Al³⁺ in the pH range 3.0-4.0. The other metal ions did not show fluorescence with DBHQ. Although the presence of Cu²⁺, Co²⁺ and Fe³⁺ decreased the fluorescence intensity of DBHQ-Ga³⁺, the addition of a fluoride ion (NaF) recovered the fluorescence by masking the interfering ions. In addition, the fluoride ions were found to enhance the sensitive determination of Ga³⁺ because the fluorescence intensity of DBHQ-Ga³⁺ was further increased approximately 2.5-fold in the presence of F⁻ (? = 0.658) from that in the absence of F⁻ (? = 0.401). The fluoride ions also masked the Al³⁺ ions, which emit fluorescence on chelation with DBHQ. Therefore, a selective and sensitive detection of Ga³⁺ was achieved by using DBHQ in the presence of F⁻. The detection limit of Ga³⁺ was approximately 50 nmol L⁻¹ (3.5 ppb). The proposed method was applicable to determine Ga³⁺ in river water.     

Nuclear magnetic resonance and optosensing properties of di-2-thienyl ketone p-nitrophenylhydrazone (DSKNPH) in non-aqueous media

The compound di-2-thienyl ketone p-nitrophenylhydrazone (DSKNPH) melting point 168-170 °C was isolated in good yield from the reaction between di-2-thienyl ketone (DSK) and p-nitrophenylhydrazine in refluxing ethanol containing a few drop of concentrated HCl. Nuclear magnetic resonance studies on DSKNPH in non-aqueous solvents revealed strong solvent and temperature dependence due to solvent-solute interactions. Optical measurements on DSKNPH in DMSO in the presence and absence of KPF₆ gave extinction coefficients of 83,300±2000 and 25,600±2000 M⁻¹ cm⁻¹ at 612 and 427 nm at 295 K. In CH₂Cl₂, extinction coefficient of 34,000±2000 M⁻¹ cm⁻¹ was calculated at 422 nm. When DMSO solutions of DSKNPH were allowed to interact with DMSO solutions of NaBH₄ the low energy electronic state becomes favorable and when DMSO solutions of DSPKNPH where allowed to interact with DMSO solutions of KPF₆ or NaBF₄, the high energy electronic state becomes favorable. The reversible BH₄⁻/BF₄⁻ interconversion points to physical interactions between these species and DSKNPH and hints to the possible use of DSKNPH as a spectrophotometric sensor for a variety of physical and chemical stimuli. Thermo-optical measurements on DSKNPH in DMSO confirmed the reversible interconversion between the high and low energy electronic states of DSKNPH and allowed for the calculations of the thermodynamic activation parameters of DSKNPH. Changes in enthalpy (ΔH^∅) of +57.67±4.20; 27.15±0.90 kJ mol⁻¹, entropy (ΔS^∅) of +160±12.88; 83±2.91 J mol⁻¹ and free energy (ΔG^∅) of −8.52±0.40; 2.66±0.25 kJ mol⁻¹ were calculated at 295 K in the absence and presence of NaBH₄, respectively. Manipulation of the equilibrium distribution of the high and low energy electronic states of DSKNPH allowed for the use of these systems (DSKNPH and surrounding solvent molecules) as molecular sensors for group I and II metal ions. Group I and II metal ions in concentrations as low as 1.00×10⁻⁵ M can be detected and determined using DSKNPH in DMSO.     

A novel di-iron(III) structure based on an ageless ligand

Salen-type Schiff base ligands possess a N₂O₂ coordination site able to chelate transition metal ions. Reaction of such a ligand with FeCl₃·6H₂O leads to the formation of a genuine dinuclear L₃Fe₂ complex in which the ligand plays a double role. The structural determination confirms that each iron ion is wrapped up by a chelating tetradentate ligand while the third one ensures a bridge in between the two Fe ions and completes to six the metal coordination sphere. Such a bridge implies a non planar coordination of the chelating ligands and induces helicity around each metal ion. Crystals are true racemates made of homochiral Λ–Λ and Δ–Δ pairs. The magnetic study confirms the absence of a spin exchange interaction through the saturated diamino chain and the presence of an axial single ion zero field splitting (ZFS) D equal to −0.7 cm⁻¹. The Mössbauer spectra show a unique asymmetric quadrupole-split doublet with isomer shift values, δ, of 0.342(2), 0.438(2) and 0.450(2) mm s⁻¹, and quadrupole splittings, ΔE_Q, of 0.826(4), 0.836(4) and 0.827(4) mm s⁻¹ at 293, 80 and 4.5 K, respectively. These values are in agreement with a high-spin iron(III) site in a N₃O₃ ligand environment.     

Enhancement reagents for simultaneous vapor generation of zinc and cadmium with intermittent flow system coupled to atomic fluorescence spectrometry

Simultaneous vapor generation of zinc (Zn) and cadmium (Cd) was evaluated by atomic fluorescence spectrometry coupled with an intermittent flow vapor generation system. Some complexing reagents, surfactant and transition metal ions were respectively tested as enhancement reagents. Experiments showed that an appropriate amount of 8-hydroxyquinoline or phenanthroline and nickel ion simultaneously, effectively improved the vapor generation efficiency of Zn and Cd. The volatile species generation was presumed to be a hydrogenation process interpreting how the enhancement reagents played an important role in vapor generation. Additionally, due to the instability of volatile species, reaction temperature, rapid and sufficient mixing of reagents and rapid separation of the volatile species from liquid phase were also crucial. The method of simultaneous determination of Zn and Cd by intermittent flow vapor generation led to the development of atomic fluorescence spectrometry. The detection limits (3σ_b) were 1.6 μg l⁻¹ for Zn and 0.01 μg l⁻¹ for Cd and the relative standard deviations were 3.6% for Zn (50 μg l⁻¹, n=11) and 1.7% for Cd (2 μg l⁻¹, n=11) respectively. Results for the determination of Zn and Cd have been confirmed by the analysis of CRMs with good agreement between the certified and found values.     

Synthesis of a novel bistriazene reagent 4,4′-bis[3-(4-phenylthiazol-2-yl)triazenyl]biphenyl and its highly sensitive color reaction with mercury(II)

We report the synthesis of a novel bistriazene, 4,4′-bis(3-(4-phenylthiazol-2-yl)triazenyl)biphenyl (BPTTBP), and its highly sensitive color reaction with Hg²⁺. The new reagent was synthesized in good yield by coupling 2-amino-4-phenylthiazole with 4,4′-biphenyldiamine bisdiazonium salt. Using a blend of surfactants N-cetylpyridinium chloride (CPC) and polyethylene glycol n-octanoic phenyl ether (OP) as a micelle sensitizer, the red colored reagent assembles with Hg²⁺ in pH 9.8 borate buffer according to a 1:1 stoichiometry, forming a blue oligomeric/polymeric chelating complex with a high apparent stability constant (1.1 × 10⁸ M⁻¹). Whereas the maximum absorption of reagent occurs at 510 nm with an extinct coefficient of 1.35 × 10⁴ M⁻¹ cm⁻¹, the complex absorbs at 611 nm, with an apparent extinct coefficient of 1.04 × 10⁵ M⁻¹ cm⁻¹. Beer's law is obeyed in the range of 0-15 μg/25 mL Hg²⁺, and Sandell's sensitivity is 1.92 × 10⁻³ μg/cm². In the presence of thiourea and Na₄P₂O₇ as masking agents, the method was found free from interferences of foreign ions commonly occurring with mercury. The optimized protocol has been successfully applied to spectrophotometric determination of mercury in waste water samples. The features of the new reagent associated with its special structure were discussed, and an unprecedented “domino effect” was proposed to account for its unique chelating stoichiometry with Hg²⁺.     

Artificial neural networks study of the catalytic reduction of resazurin: stopped-flow injection kinetic-spectrophotometric determination of Cu(II) and Ni(II)

An artificial neural network (ANN) procedure was used in the development of a catalytic spectrophotometric method for the determination of Cu(II) and Ni(II) employing a stopped-flow injection system. The method is based on the catalytic action of these ions on the reduction of resazurin by sulfide. ANNs trained by back-propagation of errors allowed us to model the systems in a concentration range of 0.5-6 and 1-15 mg l⁻¹ for Cu(II) and Ni(II), respectively, with a low relative error of prediction (REP) for each cation: REP_Cu(II) = 0.85% and REP_Ni(II) = 0.79%. The standard deviations of the repeatability (s_r) and of the within-laboratory reproducibility (s_w) were measured using standard solutions of Cu(II) and Ni(II) equal to 2.75 and 3.5 mg l⁻¹, respectively: s_r[Cu(II)] = 0.039 mg l⁻¹, s_r[Ni(II)] = 0.044 mg l⁻¹, s_w[Ni(II)] = 0.045 mg l⁻¹ and s_w[Ni(II)] = 0.050 mg l⁻¹. The ANNs-kinetic method has been applied to the determination of Cu(II) and Ni(II) in electroplating solutions and provided satisfactory results as compared with flame atomic absorption spectrophotometry method. The effect of resazurin, NaOH and Na₂S concentrations and the reaction temperature on the analytical sensitivity is discussed.     

A comparison of flow injection methods for sulfide determination based on phenothiazine dyes produced from diverse aromatic amines

In the present work a systematic comparison among spectrophotometric flow injection methods for sulfide determination based on phenothiazine dye production from diverse aromatic p-substituted amines were performed. The behavior of N,N-dimethylphenyl-p-diamine (DMPD), N,N-diethylphenyl-p-diamine (DEPD), phenyl-p-diamine (PPD), p-aminophenol (PAP) and other three aromatic amines was investigated and the chemical parameters of proposed flow methods were optimized by applying central composite design. For each evaluated method the concentration of amine, Fe³⁺ and H₂SO₄ was optimized and after the evaluation of reagents addition order the flow parameters were independently ascertained. Analytical signal was strongly diminished in the presence of iodide for flow methods based on the reaction of sulfide with DMPD, PPD or DEPD while fluoride was considered as an important interference for methods based on the reaction with PPD or PAP. The evaluated aromatic amines have permitted sulfide determination in a wide concentration range from 0.05 to 3.0 mg L^− 1 and limits of detection (3σ) varying from 18.8 to 51.0 μg L^− 1, for DEPD and PPD, respectively. The sensitivity of flow methods based on PPD and DMPD was higher even as PAP has permitted sulfide determination in a large sulfide concentration range. In addition, higher throughput was attained for DMPD method. The proposed methods were applied for sulfide determination in industrial wastewater and the obtained results were in agreement with reference method at 95% confidence level.