On-line electrochemically controlled solid-phase extraction interfaced to electrospray and inductively coupled plasma mass spectrometry

Electrochemically controlled solid-phase extractions of anions were interfaced on-line to electrospray mass spectrometry (ESI-MS) and inductively coupled plasma mass spectrometry (ICP-MS), using polypyrrole coated electrodes and a thin-layer electrochemical (EC) flow cell. The results indicate that electrochemically controlled solid-phase extraction (EC-SPE) can be used as a versatile potential controlled sample preparation technique for a range of anions and that the properties of the polypyrrole coatings can be modified by altering the electrodeposition conditions. In the present study, the influence of interfering anions (i.e., fluoride and sulfate), and the anion used during the electropolymerisation, on the bromide extraction recovery was investigated for EC-SPE interfaced to ICP-MS. The results of these experiments show that the interference due to the presence of similar concentrations of sulfate can be reduced when using a polypyrrole coating electropolymerised in the presence of bromide ions. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) measurements were also used to study the morphology of the coatings, as well as the variations in the film thickness within the coatings. The effect of different desorption techniques on the bromide preconcentration factor in the ICP-MS on-line flow system was also examined. Stopped-flow desorption was found to give rise to significantly increased preconcentration factors in comparison with desorptions in flowing solutions. While the desorption efficiency depends on the type of desorption electrolyte (the electrolyte in which the desorption takes place), due to the competing influx of cations, the influence of the pH on the switching charge of the polypyrrole coating was found to be small, at constant ionic strength. To study the applicability of the EC-SPE technique with respect to real samples, investigations were also made with tap water samples spiked with different bromide concentrations. The results of these experiments, which were carried out using a modified thin-layer EC flow cell allowing in situ polymerisation of polypyrrole yielding a polymer plug covering the cross section of the channel, demonstrate that 3 microM concentrations of bromide could be detected in the tap water sample. This demonstrates that the extraction technique allows extractions of low concentrations of ions in the presence of significantly higher concentrations of other similar ions. The fact that the extraction and desorption steps are electrochemically controlled makes EC-SPE particularly well suited for inclusion in miniaturised lab-on-a-chip systems.     

Electrochemically controlled solid-phase microextraction (EC-SPME) based on overoxidized sulfonated polypyrrole

A method for the extraction and selective determination of cations is proposed using electro-synthesized overoxidized sulfonated polypyrrole film. The polymer film is used for the selective extraction of trace levels of nickel and cadmium ions by solid-phase microextraction (SPME). The cation uptake and release properties of the overoxidized sulfonated polypyrrole film electrode were examined under both open circuit and controlled potential conditions for prospective applications in electrochemically controlled solid-phase microextraction. Increased extraction efficiency and selectivity toward cations were achieved in high saline content of water. Simple preparation of film coatings on a platinum wire was possible using a constant potential method. Applied positive and negative potentials facilitated the extraction and desorption of cations, respectively. Nickel and cadmium ions were desorbed into sample aliquot and determined by electrothermal atomic absorption spectrometry (ETAAS). The cation uptake and release mechanism is affected both by the cation exchange at the negative sulfonate and carboxylate moiety on the film and the altered solution pH occurring at the counter electrode caused by the applied potential. The method was validated using a standard reference material and tested for the determination of cadmium ion in commercial table salt samples.     

Electrochemical solid-phase microextraction of anions and cations using polypyrrole coatings and an integrated three-electrode device

A method for the extraction, transfer and desorption of anions and cations under controlled potential conditions employing a new integrated three-electrode device is described. The device, containing working, reference and counter electrodes, was prepared from tubes that could be moved vertically with respect to each other. In this way, a small amount of solvent, held by capillary force, remained between the electrodes when the device was lifted out of a solution after an extraction. This design allowed the potential control to be maintained at all times. With the new integrated device, it was possible to perform potential controlled desorption into vials containing as little as 200 microl of solution. The required ion exchange capacity was obtained by electrodeposition of a polypyrrole coating on the surface of the glassy carbon working electrode. Solid-phase microextractions of several cations or anions were performed simultaneously under potentiostatic control by doping the polypyrrole coating with different anions such as perchlorate and p-toluenesulfonate. The efficiency of the extractions, which could be altered by varying the potential of the working electrode, could be increased by 150 to 200% compared to extractions using normal solid-phase microextraction conditions under open circuit conditions. A constant potential of +1.0 V and -0.5 V with respect to the silver pseudo reference electrode, was found to be well-suited for the extraction of samples containing ppm concentrations of anions (chloride, nitrite, bromide, nitrate, sulfate and phosphate) and cations (cadmium, cobalt and zinc), respectively.     

Electro-optic applications of soluble polypyrrole

The optical transmittance of the film spin-cast from the polypyrrole(PPy) solution in chloroform depended on the thickness of the film. The film with 80% transmittance showed a surface resistivity of 23kΩ/□. A TN-LCD cell with rubbed PPy films as the LC alignment layers responded properly to an applied potential of 3.0V. Reflective mode cholesteric LCD cells made with black PPy film electrodes responded to AC fields to switch between the planar and focal conic states. PPy with imine structures introduced by deprotonation of doped PPy with NaOH solution was used as a diode material to exhibit a photo-current on exposing to light.     

On the break-in and passivation phenomena in polypyrrole/sulfate films

The influence of different divalent cations (M²⁺) on the electrochemical charging/discharging process of polypyrrole/sulfate (PPy/SO₄) films has been investigated. In principle, two different types of M²⁺ were found: (a) cations that cause the break-in phenomenon in the PPy film during electrochemical cycling with a gradual increase of film electroactivity and (b) cations in whose solutions the PPy film remains mainly electroinactive. Certain correlations have been drawn between several physico-chemical properties of the investigated cations and the break-in and passivation phenomena. The break-in and passivation phenomena were found to be influenced by the size and deformability of the cation hydration shell, ion covalent index and softness, as well as by the pH value of the test solution.     

Electrochemical fabrication of nanoporous polypyrrole film on HOPG using nanobubbles as templates

A versatile method for preparing nanoporous polypyrrole (PPy) film using electrogenerated nanobubbles as templates on highly oriented pyrolytic graphite (HOPG) is presented using in situ electrochemical atomic force microscopy (EC-AFM).     

A comparison of redox processes for polypyrrole/dodecylsulfate films in aqueous and non-aqueous media

Polypyrrole/dodecylsulfate (PPy/DDS) films were synthesized in aqueous and ethanolic solutions and investigated in aqueous, ethanolic, methanolic and acetonitrile solutions by cyclic voltammetry (CV). The amounts of anions and cations in the films before and after electrochemical treatment were determined by electron probe microanalysis (EPMA); the film morphology was studied by scanning electron microscopy (SEM). The results prove that the mobility of bulky DDS^– ions in PPy increases in the order: water<acetonitrile<ethanol<methanol. It was found that dopant DDS^– ions can be easily removed from PPy matrix swollen in alcohols or acetonitrile by electrochemical reduction or by soaking in electrolyte solutions of these solvents. The influence of electrochemical treatment on the change of doping level in aqueous solution is essentially less and depends on the cations in the test solution. Although the electroneutrality of PPy/DDS films during redox cycling is realized mainly by movement of the cations in aqueous solution and by movement of the anions in organic solvents, nevertheless the participation of anions in aqueous and cations in organic solvents is also established. The redox properties of PPy/DDS are more dependent on the solvent of the test solutions than of the synthesis solutions. Electronic Publication     

Potentiometric behavior of electrodes based on overoxidized polypyrrole films

Electrodes based on oxidized polypyrrole films have potentiometric selectivity toward anions. When the films are overoxidized, however, electron-rich groups are introduced on to the polymer chains, reversing the selectivity of the electrodes from anionic to cationic. In this study, electrochemically overoxidized polypyrrole film electrodes were prepared, and the conditions for film formation that lead to near-Nernstian potentiometric response were investigated. It was found that the doping ion, overoxidation solution, and pH affect the response of these electrodes. Redox interference is significantly lower for the overoxidized polypyrrole films than for polypyrrole electrodes.     

氟尿嘧啶的电化学控制释放

本文探讨了抗癌药物氟尿嘧啶在聚吡咯膜修饰玻碳电极上的电化学控制释放，结果表明药物自膜中的释放是聚吡咯膜的电化学氧化还原过程决定的。其释放量可由还原电位进行控制，并与还原电量和膜厚呈现良好的线性关系。     

All-solid-state reference electrodes based on conducting polymers

A novel construction of solution free (pseudo)reference electrodes, compatible with all-solid-state potentiometric indicator electrodes, has been proposed. These electrodes use conducting polymers (CP): polypyrrole (PPy) or poly(3,4-ethylenedioxythiophene) (PEDOT). Two different arrangements have been tested: solely based on CP and those where the CP phase is covered with a poly(vinyl chloride) based outer membrane of tailored composition. The former arrangement was designed to suppress or compensate cation- and anion-exchange, using mobile perchlorate ions and poly(4-styrenesulfonate) or dodecylbenzenesulfonate anions as immobilized dopants. The following systems were used: (i) polypyrrole layers doped simultaneously by two kinds of anions, both mobile and immobilized in the polymer layer; (ii) bilayers of polypyrrole with anion exchanging inner layer and cation-exchanging outer layer; (iii) polypyrrole doped by surfactant dodecylbenzenesulfonate ions, which inhibit ion exchange on the polymer/solution interface. For the above systems, recorded potentials have been found to be practically independent of electrolyte concentration. The best results, profound stability of potentials, have been obtained for poly(3,4-ethylenedioxythiophene) or polypyrrole doped by poly(4-styrenesulfonate) anions covered by a poly(vinyl chloride) based membrane, containing both anion- and cation-exchangers as well as solid potassium chloride and silver chloride with metallic silver. Differently to the cases (i)-(iii) these electrodes are much less sensitive to the influence of redox and pH interferences. This arrangement has been also characterized using electrochemical impedance spectroscopy and chronopotentiometry.     

Release mechanism of electrodeposited polypyrrole doped with corrosion inhibitor anions

Scanning Kelvin probe and electrochemical impedance spectroscopy were used to study the release behaviour of inhibitor anions doped in polypyrrole film (e.g. molybdate, 3-nitro salicylate). The polypyrrole coatings were formed on mild steel and zinc substrates in aqueous solution. It was shown that the release behaviour of the molybdate and 3-nitro salicylate anions depends on the size of cations in the electrolyte. The delamination is determined with the migration and incorporation of small cations.     

Electrochemically Controlled Ion‐exchange Property of Carbon Nanotubes/Polypyrrole Nanocomposite in Various Electrolyte Solutions

The electrochemically controlled ion‐exchange properties of multi‐wall carbon nanotube (MWNT)/electronically conductive polypyrrole (PPy) polymer composite in the various electrolyte solutions have been investigated. The ion‐exchange behavior, rate and capacity of the electrochemically deposited polypyrrole with and without carbon nanotube (CNT) were compared and characterized using cyclic voltammetry (CV), chronoamperometry (CA), electrochemical quartz crystal microbalance (EQCM), X‐ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). It has been found that the presence of carbon nanotube backbone resulted in improvement in ion‐exchange rate, stability of polypyrrole, and higher anion loading capacity per PPy due to higher surface area, electronic conductivity, porous structure of thin film, and thinner film thickness providing shorter diffusion path. Chronoamperometric studies show that electrically switched anion exchange could be completed more than 10 times faster than pure PPy thin film. The anion selectivity of CNT/PPy film is demonstrated using X‐ray photoelectron spectroscopy (XPS).     

Electropolymerization of polypyrrole, modified with germanium, on a passivated titanium electrode in aqueous nitrate solution: new results on catalytic reduction of protons and dissolved oxygen

Conductive polypyrrole (PPy) films and PPy films containing Ge microparticles were synthesized by anodic oxidation of pyrrole in acidic nitrate solutions using a bare passivated titanium electrode. Well-adhering black PPy films were obtained both under galvanostatic and potentiodynamic polarization. After the formation of the PPy film, during the first anodic cycle, an increase of the anodic deposition current with the number of cycles was observed, revealing the increase of conductivity of the growing film. The variations of the electrode surface area were estimated by impedance spectroscopy measurements. The kinetics of the PPy film formation is controlled by diffusion of the Py monomer in the solution. The diffusion coefficient, estimated by two different methods, was ca. 2×10^–6 cm² s^–1. The reduction rate of oxygen and protons at the Ti/PPy/Ge electrodes depends on how the Ge microparticles are incorporated in the PPy film. Optimum conditions for this incorporation are realized with thin PPy films and high Ge loading. Thermogravimetric analysis shows that the PPy film containing Ge microparticles is more thermally stable than the blank PPy film. Electronic Publication     

Study of the Properties of Electrodeposited Polypyrrole Films

Experimental and theoretical methods have been used for characterization of the properties of polypyrrole films. The AFM studies show that the morphology of polypyrrole (PPy) films on polycrystalline gold electrodes at the first stages of synthesis depends on the structure of the metal surface. It was established that mobility of anions depends remarkably on the rate of electrodeposition of the polymer film. If PPy film was deposited at relatively low current density, mobility of ClO^- ₄ anion was not high enough to guarantee electroneutrality during redox cycling and cations take part in this process especially when Li⁺ cations were replaced by more mobile ⁺ cations. Semiempirical (AM1 and PM3) quantum-chemical methods were used for theoretical studies. It was established that different size and charge of the anions together with the variation in doping levels give rise to a different optimal conformation of oligopyrrole cations which, in turn, define the resulting polymer to be either all-anti (common linear chains) or all-syn (formation of helical structures) or a combination of the two.     

Metallic and non-metallic redox response of conducting polymers

The potentiometric response of electrodes coated with polypyrrole or poly(N-methylpyrrole) films with different doping anions was studied in solutions containing the redox couples: Fe(CN)₆^3−/4−, Ru(NH₃)₆^3+/2+ and Fe(Ill)/Fe(II). The stable potential measured with the electrodes was the potential of the redox couple. The response time was instant for polypyrrole doped with dodecylsulphate ions, PPy(DS) and slow for the polymers doped with mobile anions. On the basis of electrochemical measurements and chemical analysis by EDAX spectroscopy it was found that with the PPy(DS) electrode the potentiometric response was of the ‘metallic’ type, with no change in the oxidation state of the bulk polymer. With the other polymer systems studied reduction or oxidation of the polymer bulk took place when it was in contact with a redox couple in the solution.     

Selective and sensitive determination of dopamine by composites of polypyrrole and graphene modified electrodes

A novel method is developed to fabricate the polypyrrole (PPy) and graphene thin films on electrodes by electrochemical polymerization of pyrrole with graphene oxide (GO) as a dopant, followed by electrochemical reduction of GO in the composite film. The composite of PPy and electrochemically reduced graphene oxide (eRGO)-modified electrode is highly sensitive and selective toward the detection of dopamine (DA) in the presence of high concentrations of ascorbic acid (AA) and uric acid (UA). The sensing performance of the PPy/eRGO-modified electrode is investigated by differential pulse voltammetry (DPV), revealing a linear range of 0.1-150 μM with a detection limit of 23 nM (S/N = 3). The practical application of the PPy/eRGO-modified electrode is successfully demonstrated for DA determination in human blood serum.     

Synthesis of a hexafluoropropylidene-bis(phthalic anhydride)-based polyimide and its conducting polymer composites with polypyrrole

A new electrically conducting composite film from polypyrrole and 4,4′-(hexafluoroisopropylidene)-bis(phthalic anhydride)-based polyimide was prepared. Pyrrole and the dopant ion can easily penetrate through the polyimide substrate and electropolymerize on the platinum (Pt) electrode due to the swelling of the polyimide on the metal electrode. The electrochemical properties of polypyrrole-polyimide (PPy/PI) composite films have been investigated by using cyclic voltammetry. The PPy/PI composite film is suitable for use as the electroactive material owing to its stable and controllable electrochemical properties. The electrical conductivity of composites falls in the range 0.0035–15 S/cm. Scanning electron micrograph, FTIR, and thermal studies indicate that PPy and PI form a homogeneous material rather than a simple mixture. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3009–3016, 1997     

Surface modification of FePO4 particles with conductive layer of polypyrrole

Polypyrrole–FePO₄ powder was synthesized by an oxidative polymerization of pyrrole monomer on the surface of FePO₄ powder. The polymerization reaction was initiated using hydrogen peroxide in an acidified solution and catalysed with Fe³⁺. The samples were investigated by light microscopy (LM), scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). These methods confirmed the presence of polypyrrole on FePO₄ particles and its homogeneous distribution in the composite material. To determine the PPy content in the PPy–FePO₄ composites a thermogravimetric analysis was used. Cyclic voltammetry curves (CV) were measured and compared in a non-aqueous lithium salt solution for electrodes consisting of pellets made from pure FePO4 and FePO₄/PPy. Electrochemical impedance spectroscopy (EIS) showed that coating of PPy significantly decreases the charge transfer resistance of PPy–FePO₄ electrodes.     

Polypyrrole Bilayers: Charge Trapping and Application for Amperometric Ions Sensing

Bilayers composed of polypyrrole: doped by perchlorate ions (PPy(ClO₄) – anion exchanging inner layer) and by dodecyl sulfate ions (PPy(DS) – cation exchanging outer layer) are very effective charge trapping systems that are usually not observed for other bilayers comprised of polypyrrole. Chronopotentiometric experiments carried out for oxidation and reduction showed that the trapping effect in the inner layer resulted from different ion exchange properties of the component polymers, leading to a low permeability of the reduced outer layer towards anions. Estimated diffusion coefficients of Cl^? anions in the oxidized and reduced PPy(DS) are in the range of 10^?9 and lower than 10^?10 cm² s^?1, respectively. The presence of the outer layer limiting the ion transfer was found to be beneficial to improve the signal resolution in amperometric mode of ion sensing within wide KCl concentration range, from 10^?5 M up to 3 M. The influence of experimental conditions (film thickness, response time) on optimization of this novel kind of polymeric bilayer ion sensors was studied.     

Force detection with Donnan equilibrium in polypyrrole film

Mechanical stimuli to polypyrrole (PPy) composite film could be detected as a spike-wise current by applying or releasing a stepwise tensioning-load in electrochemical cell. The current polarity observed here varies with the film preparation. A negative current was observed in the PPy film electrodeposited in dodecylbenzene sulfonic acid (PPyDBS), besides a positive current was observed in the film electrodeposited in bis(trifluoromethane sulfonyl)imide (PPyTFSI) with applying a load. Reversal currents were observed with releasing a load from the films. Switching of the polarity of the induced current well corresponded to the film actuation polarity, indicating that the current induction is the phenomenological counterpart of the electrochemical actuation. Perturbation of Donnan equilibrium by external pressure possibly generates an ion flux across the film/electrolyte interface, resulting in (dis)charge of the PPy similar to the redox process.